Search Documents

By Y H. Zhu, X X. Tang, Y C. Yin, M L. Xing

Based on the stiffness theory, the stiffness difference and energy supply of surrounding rocks are important inducing factors for strain burst. However, due to the lack of multi-level low stiffness testing machine, there are few experimental studies on rock failure mechanisms under the influence of loading stiffness. This paper introduced a self-developed rock testing system with changeable stiffness. The main testing machine of this system is a combined structure of inner and outer frame. The change in the loading stiffness is achieved by using a stiffness servo control system to control the energy accumulation in the inner frame. The tests of the sandstone specimens under three different loading stiffnesses in the testing system showed that the loading stiffness did not significantly affect either the uniaxial compressive strength or the Young’s modulus of the rock. However, the post-peak stress-strain curve of the rock became smoother and steeper when the loading stiffness was decreased, and the stress drop rate increased. It is shown that the stress drop rate had a power function correlation with the loading stiffness. After the peak load, the inner frame of the testing system rebounded several times at high speeds. The magnitude of the instantaneous rebound speed and the rebound duration increased with the decrease of loading stiffness. Both the mean rebound velocity and the total rebound deformation had power function correlations with the loading stiffness. The loading stiffness has limited effect on the energy storage and energy dissipation characteristics of the specimen, while the released energy of the testing machine increases as the loading stiffness decreases, which is the key factor affecting the failure mode of the specimen. According to the test results, a rock burst mechanical model considering the stiffness is established, and the energy supply mechanism of rock burst is quantitatively explained.

Nov 29, 2022

By D Craw, P Lindsay, B Peake

The geochemical properties of Kaiata Mudstone and Brunner Coal Measures are evaluated in order to determine their suitability for placement at the proposed Cypress and existing Stockton mines. Correct scheduling of this waste material is needed in order to prevent sulfide oxidation and the generation of acid rock drainage. The Kaiata Mudstone has both acid generating and acid neutralizing properties. Results from this study and previous research from Kingett Mitchell Ltd (2003), indicate that within the Kaiata Mudstone sulphur content decreases with distance away from the Brunner Coal Measure/Kaiata Mudstone contact, while calcium carbonate content increases; sulphur values range from 0.33 to 4.23 wt %; and the acid neutralizing capacity ranges from 0 to 10.4 wt %. The Brunner Coal Measures have a low capacity to neutralize acid and sulphur content is variable ranging from 0.25 to 3.5 wt %. Appropriate control measures are therefore needed for the Brunner Coal Measures and any Kaiata Mudstone within close proximity to its contact. Tests have been undertaken to develop a rapid field or laboratory procedure to define the potentially acid-forming from the non-acid-forming Kaiata material. Results indicate that paste pH, Net Acid Generation (NAG) and Carbonate Bomb tests are suitable. Results from the Carbonate Bomb Test show a strong relationship with the Acid Neutralizing Capacity (ANC) and the Net Acid Production Potential (NAPP), indicating that this method may efficiently determine non-acid forming material in the field within fifteen minutes. Ongoing research includes kinetic column and shake extraction tests. These tests will quantify what trace elements could be leached from the waste rock and provide information on the usefulness of alkaline producing products such as Bauxsol, Limestone and Cement Kiln Dust.

Jan 1, 2004

By P Cepuritis, G Chitombo a, I Brunton

There is a significant amount of past evidence that links blasting and occurrences of slope failure. Particularly of great concern at Telfer Gold Mine is the effect of open pit blasting on the stability of the footwall slope above the underground portal and the stability of underground structures. For this reason, Newcrest Mining Ltd invited JKMRC to conduct necessary field measurements and numerical modelling with the following objectives:assess the dynamic stability of the footwall slope above the portal; assess the characteristics of current and future blasts in the open pit; and prepare open pit blasting guidelines that will minimise the detrimental effect of blasting on slope stability. To achieve these tasks it was necessary to develop a scaled distance attenuation curve for blast vibrations. In order to validate the developed vibration attenuation curves it was necessary to monitor vibrations from a production blast. Using JKMRC blast design software tools, the vibration of the production blast was also modelled from the blast design and vibration results from single hole blasts. The intention was, assuming that the observed and modelled vibrations were close in terms of frequency and amplitude, to use the software tools to model the vibrations of future blasts and assess their likely effect on slope stability. Numerical modelling of the dynamic stability of the footwall slope was done using the FLAC finite difference code and the UDEC distinct element code. The results of the numerical modelling and of the field measurements of the blast induced ground vibrations were combined into the blast design rules that relate distance between the slope and the blast, charge weight per delay and number of blasts necessary to cause failure of the slope.

Jan 1, 1999

By J Galvin

This paper addresses the actions of the Australian mining industry, its regulators and educational providers towards ensuring that a pool of competent mine managers is maintained in Australia and that mine management remains a desirable career path for future mining professionals. The Australian and global mining industries are experiencing an acute skills shortage. Mine managers, traditionally drawn from the ranks of mining engineers, are at the sharp end of this shortage. Exacerbating the shortage is a perception that a professional mine manager is not an attractive career option. This perception is influenced by the following forces which combine to make the role of a modern mine manager very demanding:legislative requirements for owners and managers to ensure (guarantee) the safety and health of employees; an increasing trend towards prosecution over exposure to risks to health and safety a need to be more aware and responsive to community and environment; financial, technical and æpeopleÆ pressures traditionally associated with the job of managing a mine; and mine management roles being filled by younger and less experienced professionals. Universities and other educational providers have the challenge of both ensuring that undergraduates are exposed to these issues during their study and continuing to promote mine management as a desirable career option. Anecdotal and statistical evidence indicates that young graduates are choosing and remaining in technical roles rather than taking on the challenge of mine management. Furthermore, it is suspected that the issues referred to above are contributing to the low retention rate of young professionals at mine sites. The challenges are not insurmountable, however. This paper reviews the initiatives of industry, the regulators and educational institutions in addressing these challenges. It includes a focus on:prosecution policies and their impacts, tertiary education program content and delivery modes, CPD initiatives of the Mine Managers Association of Australia, and alternative pathways for obtaining mine management qualifications.

Jan 1, 2006

By R Berthelsen

The Peak Gold Mines Pty Ltd (PGM) operations are located approximately 9 km south of Cobar, NSW. PGM currently mines and treats ore from three separate orebodies within 5 km of the original plant. Production from the original Peak orebody ceased in April 2002, with ore currently sourced from underground at New Occidental and Perseverance, while New Cobar supplies ore from an open cut mine. In March 2003, Wheaton Minerals Asia Pacific purchased the operation from Rio Tinto who operated the mine for around ten years. The Perseverance deposit is situated between 600 and 1000 m south of the Peak orebody. Access is via shaft from Peak to 630 m below surface and then by decline to the northern end of the deposit locally known as Zone A. Development of the resource commenced mid 2002 to set up for a long hole open stoping operation at 25 m level spacing. The first production stope was successfully brought on line December 2003. The Perseverance deposit is hosted by sediments and volcanics along the eastern margin of the Devonian Cobar basin and is one of many deposits with the Cobar Gold Field. The Cobar Gold Field has produced approximately 2.5 million ounces of gold since 1880. The Perseverance area had long been considered prospective due to the presence of old workings at the southern extensions of Peak line of lode. Significant mineralisation was first discovered at Perseverance in 1994 when PGM drilled a hole targeted 950 m below the historic workings. The target was based on an apparent plunge to the stratigraphic controls to the Peak Orebody. Subsequent exploration within and around the ægreaterÆ Perseverance area has been significantly aided through the use of downhole electro-magnetic surveys due to the close spatial association between gold and sulfide mineralisation.

Jan 1, 2004

White Cliffs Opal Field is situated in the Parish of Kirk, County of YulguIgra, New South Wales, about sixty miles from Wilcannia, and the River Darling. It is near the southern edge of the cretaceous basin of the interior of Queensland, New South Wales, and South Australia. Twelve miles south-west of the field, at Tarella station, a well sunk at the homestead reached silurian slates at about 127 feet, getting no water but about three miles north-west from the originally discovered and no central portion of the field, a well was sunk by the Momba, Pastoral cmpany, to a depth of 270 feet all the way through the cretaceous beds. At 250 feet a small supply of water was struck, but so much mineralised as to be quite useless. The temperature also was so high that a man could not keep his hand in it and Mr. Hogarth, the Momba Pastoral Company's manager, informs me that so corrosive was the action of the water, that a shovel left down the well for a fortnight, at the time of sinking, was completely eaten away.The well having now fallen in, I have been unable to obtain any of the water for analysis.The western termination of this portion of the cretaceous basin is situated about twenty miles from the present opal field, at which distance the slates, with (probably) devonian sandstones and quartzites resting unconformably thereon, commence to appear. The opal bearing country, as far as at present known, follows a more or less well defined line running north and south towards the northern end of the field, and north-east and south-west towards the southern extremity.

This paper traces briefly the reasoning which led to the decision to extend the existing internal shaft at the Rosebery Mine and to instal underground a larger winder (No. 2 Hoist) with capacity to handle all hoisting requirements to a depth of approximately 2,500 ft. on an incline varying from 83" to 55" to the horizontal. It then covers the specifications and selection of the winder, the design of the winch chamber, rope raise and bins, the excavation, support and lining of the chambers and the transport to site and installation of the machinery. Finally a brief description is given of the mechanical and electrical parts of the winder.INTRODUCTIONThe existing shaft winder on the internal inclined shaft situated on No. 8 Level of the Rosebery Mine had reached the limit of its capacity. Hoisting 21-ton capacity skips in balance, with a 13/16-in. diameter rope, it required four layers of rope on the 3 ft. 6 in.drums to reach the loading station under No. 12 level at a depth of 864 ft. (Fig. 1). This entailed heavy wear on the multi-layered rope and heavy stresses on the cheeks of the drums. Continuous working on three shifts was necessary to handle ore, men and materials, and a hold-up from any cause whatever meant an interruption to production on the lower levels of the mine. The maximum output of the hoist whilst hoisting from the No. 12 level loading station was 50 tons per hour. It was obvious therefore, that a larger winder was required if output was to be maintained.Diamond drilling had proved the existence of sufficient ore at depths well below No. 12 to warrant exploitation and a decision had to be reached on the means of hoisting this ore.

Jan 1, 1958

By Stein A

The general mechanism of recrystallisation for cold worked metal is well established, and need be only briefly summarised with a few references to recent articles which clarify minor points. The types of extension, whether by stretching, drawing, hammering, rolling, etc., do not alter the general principles (1), although quantitative results may differ somewhat, particularly with regard to differences between the surface and interior of samples.These principles can be summarised as follows: The first stage in annealing is a recovery (sometimes known as relaxation) of physical properties such as hardness, elongation, etc., without any appearance of recrystallisation; the second stage involves a further alteration in physical properties, accompanying the formation of new recrystallised grains which replace the original structure; a possible third stage involves an increase in the grain size of the completely recrystallised structure by absorption of smaller grains by larger ones. These three stages will be referred to as recovery, recrystallisation, and grain growth. Depending on conditions, the three stages may be clearly marked or may occur more or less simultaneously.For a given annealing temperature, cold deformations below a certain amount fail to give recrystallisation, and the final structure consists of the original grains which have recovered and possibly become more equiaxed. When a certain deformation, critical for that annealing temperature, is given, recrystallisation can occur, and will give the maximum recrystallised grain size.Increasing deformations beyond this give progressively smaller grain sizes.For each material there is a minimum recrystallisation temperature, below which recrystallisation will not occur whatever the deformation or time of annealing. For a given deformation there is a temperature, critical for that deformation, below which recrystallisation will not occur, and above which it will take place with increasing rapidity.

Jan 1, 1947

By M Behrens, A McPhee, B D. Hegan

This paper describes the design and construction of twin 400 m long road tunnels as part of the Northern Motorway Extension Project in Auckland, New Zealand. Construction of the tunnel civil works is now completed and installation of mechanical and electrical systems is well underway. The tunnels are expected to be open for traffic at the end of 2008. The paper will address the design aspects of the project including: tunnel alignment and cross-section, geotechnical conditions and rock support, waterproofing and concrete lining and fire and life safety. The paper will cover the bored tunnel section, the cut-and-cover tunnel section, cross passages and portal structures. The design brief included a requirement for the tunnels to be a gateway to Auckland and this required particular attention to be given to the visual appearance of the finished tunnel structure. The final arrangement of the portal structures and a requirement for recesses in the concrete lining for emergency cabinets, deluge pipework and cable runs, reflects these requirements. The tunnels were excavated by a roadheader and road planer using a heading and bench. Initial support was provided by a combination of lattice girders, cement grouted rock bolts and steel fibre reinforced shotcrete. The permanent lining consisted of installation of a drainage geotextile and waterproof membrane, followed by cast in situ unreinforced concrete. Each portal consists of a cut-and-cover section. This paper describes the tunnel construction methods, including the particular requirements for safety, the environment and community relations. The tunnel is fitted with a compartmentalised deluge system for fire fighting purposes. The tunnel control centre is incorporated into the control centre for Auckland Harbour Bridge, some 30 km from the tunnel location.

Jan 1, 2008

A number of terrane reconstructions conflict with global plate histories or with data from adjacent regional studies. Paleogeographic maps have ignored terranes thus are over-simplified. This paper represents an attempt to "marry" Mesozoic global plate reconstructions and terrane analysis to produce examples of a "third generation" of global plate tectonic maps. The best approach to global terrane analysis involves intercomparison of all regional data and the evolving global model. Data conflicts within and between terranes and regions must be resolved by a system of relative data reliability "weighting." The most reliable and useful data are those which constrain "departure" (rift) and "arrival" (collision) times. Certain ad hoc decisions aid in the analysis (e.g. only one net vector allowed per plate). The maps that follow summarize Early Mesozoic global tectonic history at three critical junctures: 240 MA (Triassic); 180 MA (Jurassic); and 120 MA (Cretaceous). Due to space limitations, maps drawn at 20 m.y. intervals appear elsewhere. A preliminary Middle Triassic reconstruction is presented in Figure 1. Major plates and continental blocks are labeled; smaller blocks are marked with abbreviations. Examination of Figure 1 indicates the necessity of modeling Triassic tectonics with at least 68 blocks. Spalling- off of microcontinental slivers from Gondwanaland is active some 70 m.y. before the actual breakup of the supercontinent. In the SW sector of the Pacific, the Australian margins were embroidered with several terranes (e.g. Sumba) which eventually rifted away and crossed Tethys. The NW sector at this time included 10 microcontinental chips forming a huge archipelago along the Asian margin. All blocks inboard of Indochina collided by latest Triassic. Terranes of the NE sector include several (e.g. Arctic Alaska) along the North American margin, and at least six large blocks (e.g. Stikinia) drifting SE with the Farallon Plate. The SE sector

Jan 1, 1987

By Moxon N. T, Berndt J. R

BHP-Utah Coal Limited's Peak Downs Mine is located in Cen- tral Queensland, approximately 200 km south west of Mackay. The annual raw coal production of the mine is over 8 million tpa, requiring the removal of about 40 million cubic metres of prime overburden. This is achieved through the use of five large draglines. The large depths of overburden (up to 55 metres) encountered over half the strike length of the mine enables cast blasting to be carried out in conjunction with draglines employ- ing the chopping method of digging. The objective of cast blast- ing is to use explosive energy to move as much material directly into spoil as possible. The additional costs of drilling and blast- ing are offset by reducing dragline rehandle. Two factors which are of primary importance to the design of cast blasts are initiation control and material velocity. High speed motion picture photography is a powerful diagnostic tool to quantify these aspects of blasting (Winzer, Montenyohl and Ritter, 1979; Chiappetta et al., 1983; Anon., 1983). The objec- tives of such analysis are to: 1. Determine the burden velocity, 2. Determine the time to initial movement (that is, the inter- val between a face hole firing and the initial movement of the burden), 3. Check the accuracy of the initiation sequence. BHP Central Research Laboratories (CRL) and Peak Downs Mine monitored a cast blast in the mine's Winchester Pit on 18 August, 1988. The objectives of this exercise were to: 1. Quantify current cast blast performance, providing a base case for comparison with modified blast design. 2. Compare two orientations of angled holes within the blast. 3. Assess the effectiveness of cast blasting utilising an air-deck. 4. Check blast timing with respect to burden movement times.

Jan 1, 1989

THE exceptional rainfall characteristic of the West Coast of Tasmania, in conjunction with the rugged topography of the district, has always suggested the utilization of water-power, and from the earliest days of the Mount Lyell Company theeventual installation of a hydro-electric power scheme, making use of some near-lying lake, has constantly been kept in view. At the period of the inception of the company, however, the time was not ripe for such an undertaking, and it is only oflate that the various important considerations involved have sanctioned incun;ing the heavy expenditure necessary, with the positive assurance of permanently reaping the benefits expected. The West Coast of Tasmania contains many lakes of varioussites; situated at high levels, and, although the catchments of these lakes are not very extensive, still, the excessive rainfall is so constant over long periods that its regularity may be relied on as offsetting the limited catchments. The explanation of the abnormal rainfall is simply the circumstance that the West Coast Range forms the first high land barrier which is met by the moisture-laden westerly and north-westerly winds blowing off the Southern Ocean. By the time the clouds strike the mountains they ride very low, consequently the elevation of the range, the peaks of which do not exceed 3000 to 4000 ft. above the sea, is sufficient to cause a copious precipitation. Lake Margaret, which is situated five miles north of the reduction works, was first recognized as a possible source of waterpower by Mr. Hugh Ohrisp, a surveyor, who visited it about 1893-4. Earlyl in 1895, while the preliminary work on the erection of the first furnaces of the Mount Lyell Co.'s reduction...

Jan 1, 1915

By Balint F

The Izok massive sulphide deposits are located in the Northwest Territories of the remote western Canadian Arctic. Together they represent one of the highest grade undeveloped zinc-copper resources in North America. Metall Mining Corporation is presently engaged in a feasibility study on developing the Izok property as well as actively exploring for additional reserves. The Izok deposits are Archean-aged, volcanogenic massive sulphide (VMS) bodies hosted within and near the top of a thick sequence of predominantly felsic pyroclastic rocks. The hangingwall package includes additional felsic volcanoclastics, dacitic and basaltic flows, thin sulphide-rich iron formations, and turbiditic sediments. The felsic volcanics are intruded by syn- to late-hydrothermal dacitic dykes and sills and post-hydrothermal gabbroic dykes and sills. Both intrusives are interpreted to be volcanic feeders to overlying flows. All lithologies are cut by much later irregular granitic pegmatite dykes and regionally metamorphosed to pyroxene homfels grade. The deposits occur within a large kilometre-scale soda-depleted alteration zone. The immediate footwall and hangingwall rocks to the deposits are characterised by zones of muscovite-biotite (with or without sillimanite), lesser chlorite-biotite-cordierite (with or without anthophyllite), and locally intense silicificified and albitised zones. All lithologies have been affected by a later calcic metasomatic alteration. As currently defined, the Izok Zn-Cu-Pb-Ag deposits comprise a cluster of four complexly-zoned composite lenses: the Northwest, North, Central, and newly discovered Inukshuk deposits. The first three deposits are amenable to open pit mining while development of the Inukshuk deposit will require underground methods. The combined mineral inventory of the Northwest, North, Central and Inukshuk deposits at present totals 15.6 million tonnes with a grade of 2.4 per cent Cu, 13.8 per cent Zn, 1.4 per cent Pb, and 74.6 g/t Ag.

Jan 1, 1993

By W. M. LONIE

Address by the President of the Institute (Mr W M Lonie) in making the presentation of the Certificate of Honorary Membership to Sir Ian McLellan, K.C.G.M, K.B.E. Address by Sir Ian McLellan after accepting the award.

Jan 1, 1979

The paper discusses the special mixing requirements for Metallurgical Plant Design and outlines the problems associated with the agitation in Mineral Processing Industry today. It also covers new applications such as state of the art large leach tanks and backfill for deep mining.

Jan 1, 2004

By A P. Brown

Comparison of legal permits required for mining (as opposed to prospecting or exploration) inNew Zealand, under the Mining Act 1971 and the Resource Management Act/Crown Minerals Act 1991. Mining generally receives the same treatment as any other industrial or commercial activity.

Jan 1, 1995

Cyanide is a significant contributor to the cost of producing gold. Any reduction in cyanide consumption that is achieved through more reliable measurement, and/or more efficient management of cyanide dosing rates, can produce a significant financial saving to the mine operation.

Jan 1, 1997

It is a pleasure for me to be able to address you today. My Chairman, Sir Eric Neal will not be able to be here until later in the morning and he has asked me to deliver this speech on his behalf.

Jan 1, 1990

By Brown AP

Comparison of legal permits required for mining (as opposed to prospecting or exploration) in New Zealand, under the Mining Act 1971 and the Resource Management Act/Crown Minerals Act 1991. Mining generally receives the same treatment as any other industrial or commercial activity.

Jan 1, 1995

The electrochemical dissolution of gold and other noble metals in hydrochloric acid using alternating current has been investigated. The experimental results show that this technique is efficient for dissolving pure noble metals and offers prospects for their extraction from wastes and poor ores.

Jan 1, 1992