Search Documents

By Fukuda M, Kurita K

A mathematical model for estimating the liquid level in the hearth is presented. The analytical result was checked on a cold two-dimensional model and an additional boundary condition for the fundamental equation resulted. The applicability of the resultant equation was investigated on a cold model and a regression equation obtained for the average liquid level for Kashima No. 1 BF. Comparison of calculated and observed results were in fairly good agreement. It is concluded that the liquid level in the commercial furnace can be calculated from the measured values of pressure in the bosh and operating conditions.

Jan 1, 1975

Today computers are accepted as a standard item in industry and they perform a variety of tasks over a wide spectrum of activities from mine planning and CAD to data processing and spreadsheet work. However many problems particularly in the. area of decision making where there are no clear mathematical models available and usually the output or answer is dependent to some extent on a heuristic approach, don't lend themselves to conventional solutions using standard procedural algorithms. Recently a number of techniques have evolved primarily from the enhanced capabilities of modem equipment, which are capable of solving these problems. This paper is a brief overview of these rather unconventional developments of computer technology in the area of artificial intelligence with reference to their application in mining.

Jan 1, 1993

By M J. Begbie, K B. Sporle

The Golden Cross low sulfidation epithermal deposit produced approximately 750,000 ounces of Au from two ore zones: the underground Empire Vein System and the open pit stockwork. The Empire Vein System has at least eight stages of vein formation: (1) sulfide veins, (2) black veins, (3) massive veins, (4) banded veins, (5) thin white veins, (6) crumbly veins, (7) massive/platy calcite veins, and (8) flattened rhomb calcite veins. Gold mineralisation occurred relatively early in the lifetime of the system, dominantly during 2 through 4. The late calcite veins (7 and 8) and early sulfide veins (1) are barren. The vein system formed in a dominantly extensional environment, though some compressional faulting may have also existed during vein formation. There is no evidence for significant strike-slip faulting during vein formation, highlighting the fact that explorationists should pursue on-site structural patterns rather than fashionable models.

Jan 1, 1998

By D B. Donato

Gold mining cyanide-bearing solutions can pose a risk, cause significant wildlife deaths and adverse public relations and result in non-compliance with regulatory conditions. The International Cyanide Management Code for the Manufacture, Transport and Use of Cyanide in the Production of Gold (the Code) was developed as a voluntary code to encourage industry-wide improvements in managing cyanide responsibly. The Code requires design and implementation of robust monitoring programs for compliance under the following standards of practice: 4.1, 4.4 and 4.9. A robust monitoring regime can be complicated as each processing and tailing system is different. The following systems are commonly used in Australia: carbon-in-leach (CIL); carbon-in-pulp (CIP); heap leach process ponds; tailing waste disposal systems; peripheral discharge, central discharge and in-pit disposal. Some terrestrial wildlife can be denied access by fencing tailing storage facilities (TSFs) or other physical barriers, therefore limiting wildlife interaction with cyanide-bearing tailing and solutions to mainly birds and bats. While wildlife monitoring programs for processing and TSFs contain similar core attributes, it is necessary to adapt monitoring to take into account the site-specific features of each system. These core attributes are discussed in this paper, with reference made to cyanide concentration and associated methodologies. The issue is considerably complicated if tailing solutions are deemed or discovered to be toxic to wildlife. Essentially cyanides are required to be measured to gain an understanding of the concentrations to which wildlife may be exposed. This usually equates to measuring the cyanide concentration of solutions entering and leaving a tailing system. To assess the risk to wildlife presented by tailing and heap leach systems it is necessary to monitor both the hazard (cyanide concentrations) and the exposure (live wildlife species, presence and interaction). These tasks need not be arduous and a system of simple frequent monitoring has been developed and implemented for Code compliance. The wildlife monitoring developed by Donato Environmental Services (DES) and used at mining operations departs from the industry norm. It documents observer effort, live wildlife presence, habitat and behaviour in a tailing system, as well as deaths and carcasses. A greater understanding of wildlife cyanide toxicosis associated with this monitoring approach will enable mining companies to adopt a proactive approach to significantly reduce, or preferably eliminate, the impact on wildlife and assist in gaining Code compliance.

Jan 1, 2007

By R S. Sing, M D. Yadav, G Udaybhanu

This paper presents the results of the first part of a research project to study the effect of various inhibitors to reduce the spontaneous heating susceptibility of some highly susceptible Indian coal seams. In this investigation 11 inhibitors were chosen and applied at three, five and ten per cent of their concentrations in an aqueous solution for four coal samples collected from four different seams. The susceptibility of coal samples, before and after application of these inhibitors, was determined by carrying out crossing point temperature (CPT) analysis. The findings of this study have indicated that it is possible to retard the tendency of spontaneous heating of Indian coals to a considerable extent by the application of six of the inhibitors studied. Further, these inhibitors were tested in 1:1 combination to study their synergistic effect. Finally the economics of the application of these inhibitors has been analysed and four inhibitors are recommended for field use. These results have direct application to control fire and improve productivity and safety in coal mines.

Jan 1, 2005

Suppression of the explosion of the world population and the surprising increase of waste and emissions are major targets confronting mankind in this century. Recycling and waste minimisation are key words for sustainable development in a highly industrial society. The argument is really whether or not recycling done well is the solution to the environment problem for the following generation. If energy is not necessary in the recycling, all materials have to be recycled. The greatest interest among the environmental issues is the regulation of CO2 gas emission. It must be recognised that it is not possible to completely renew expended energy. Some of the recycling systems currently used are thought to increase the load on the environment rather than to be beneficial. Although metal industries have consumed tremendous amount of energy and discharged a large quantity of CO2 and solid waste, the metals have supported a high quality of life. The metal production industries such as the iron and steel industry and the non-ferrous metals industry can work well recycling of not only metals but also other materials without consuming more energy. Waste plastics, for example, are use as a reductant in a blast furnace. The role of metallurgical industry in the recycling-based society is introduced in the present paper to recognise how the metal industries can contribute recycling and waste minimisation.

Jan 1, 2002

Based on the examination of thirty sets of contiguous matte and slag samples taken from industrial nickel smelters a relationship is predicted between oxidic nickel in slag, oxygen in matte and the Ni/Fe ratio in the matte. Oxidic nickel in the slag is found to increase with an increase in oxygen content of a matte of constant Ni/Fe ratio, and it is proposed that the relationship may be used to predict nickel solubility in slag from a knowledge of matte composition alone.

Jan 1, 1980

By Grieveson P, Terry B. S

Carbothermic reduction of sulphide minerals for achieving a selective separation of metallic species from complex minerals has been discussed by considering the prevailing oxygen potential during the course of reaction. Construction of univariant plots for the reduction of sulphides with carbon monoxide gas or carbon and in the presence of either lime or anhydrous calcium sulphate is the key feature of this work. The theoretical calculations for univariants in the Cu-Fe-S-O system indicated a preferential separation of metallic copper and iron by imposing a chemical potential. This is evident from a logarithmic plot of sulphur dioxide partial pressure against reciprocal temperature. The results are compared with empirical data for the reduction equilibrium. The reduction behaviour of the constituent sulphides are also discussed together with the experimental results and theoretically predicted phase stability diagrams.

Jan 1, 1992

The Australian lead-zinc industry faces a future in which the world market is likely to show at best only minimal growth and in which there will be increasing competition. Its production facilities use mature technologies employing expensive labour and increasingly costly energy in a country which demands the highest standards of environmental performance. Returns on investment are already unsatisfactory.Technology for survival would appear to indicate a need not only for more efficient capital, labour and energy usage combined with improved environmental performance, but also flexibility to handle more complex materials than the traditional, virtually single metal concentrates. This offers the potential for improved overall economics from the mine onwards, but will demand efficient separation and by-product recovery processes.In the lead industry these problems are being addressed in several emerging technologies. With zinc, the situation is less clear.

Jan 1, 1985

The Hill 50 Gold Mine is situated at Boogardie, 3 miles on a bearing of 295 degrees from; Mount Magnet township. Mount Magnet lies 300 miles north-north-east of Perth, Western Australia (Fig. 1).The older workings of the mine may be identified with those of Sirdar, Gold Mining Lease 696M The Sirdar had been worked before 1902 though no records remain, and irom 1903 to 1912 about a thousana tons at a grade of 6' 2 dwt. was extracted annually; by the end of 1918 6,225 oz. of gold had been obtained from the milling of 17,852 tons of ore. In view of these yields, and the length and width of the lode, this mine was early recognized as one of the most promising in the district. From 1919 to 1924 the ground,including G.M.L. 1282M, was held as Mt. Zion G.M.L. 1183M.The Hill 50 Gold Mine N.L. company took up the workings as Hill 50 G.M.L. 1282M in 1934 and have continued operations to the date of writing. To the end of 1956 the Hill 50 Gold Mine had yielded 982,106 tons of ore for a return of 448,'602 fine oz. of gold.The mine has been described by: J utson (1915), Feldtmann (1920), Johnson (1949), and Finucane (1953). Finucane (1953) details the mine structure to a depth of 414 ft. The author was able to examine the mine to a depth of 1305 ft. Detailed main level mapping to the 1060 level and a detailed surface examination have revealed aspects of the structure which were previously obscure.

Jan 1, 1960

By Fink ST

Management requires up-to-date information on the activities of an enterprise in order to maintain control and to assist in decision-making and planning. In today's environment it is essential that this information is immediately available and in an easily assimilated format. If this is not the case, management is forced to make decisions based on intuition and past experience. At Mt Newman Mining Co, a computer application has been developed and implemented with the objective of providing this type of information to management. The Key Parameter Reporting System (as the application is known) allows for daily (constant) on-line capture of selected production statistics, safety statistics and free format textual comments relating to topics such as industrial relations, major maintenance and other pertinent news. Information can be retrieved,'and displayed or printed in either a tabular or graphical format. All senior managers have colour visual display units in their offices for immediate access to the system. Access to selected sensitive information is controlled. All company staff are able to retrieve unsecured information from the system via visual display units installed in all company Locations.

Jan 1, 1983

The Aberfoyle Tin Mine lies on a wide sloping bench about 2,000-2,500 ft. above sea level, at Rossarden, 14 miles north of Avoca, in north-eastern Tasmania. The quartz-cassiterite veins were discovered in 1916, but mining did not begin until 1926. Trenching revealed seven small tin-bearing veins within a width of 57 ft. of Palaeozoic slates and sandstones, and it was assumed that the mineralization extended beneath the adjacent cover of Permian strata, but the presence of the main vein system (the 26 Vein System) was not suspected until the Aberfoyle Fault was discovered late in 1928.The mine has now been developed on thirteen levels, to a depth of 1,350 ft. The lower limit of economic mineralization appears to lie at about the ll-level, which is 1,060 ft. vertically below the concealed outcrop of the main veins. Production of tin and tungsten concentrates began in 1932, and to date more than 550,000 tons of ore have been mined for a recovery of 8,856 tons of tin concentrates, and 3,056 tons of wolfram concentrates, valued at approximately £6,500,000.This paper reports part of an investigation undertaken by the Mineragraphic Investigations Section of C.S.I.R.O. to study the mineral composition of the ore in relation to the apparent failure of cassiterite and wolfram mineralization to extend below the present working limits of the mine, and was first issued as Mineragrapnic Report No. 639.GENERAL GEOLOGY:The deposit consists of a series of quartz veins in a northsouth trending sheeted zone, transecting folded slates and...

Jan 1, 1957

By B Delaney

For worker safety, mining companies are required to stop production and inspect hoist ropes. Visual inspection is generally done daily and EM inspection occurs every three to four months. During visual inspection, rope speed is generally reduced so an inspector can look for problems. In EM testing the LMA and LF traces are printed on a paper strip chart and a skilled operator interprets these traces. Mining companies only find large defects during visual inspection and are sometimes concerned about the content of EM trace information. This paper will present research outcomes that show how muck can be hoisted while performing a complete visual rope inspection at full speed. Other research results will show that digital signal processing can increase the amount of information available to the EM rope inspector. The research was funded by Inco, C-CORE, three AMIRA International sponsors and six sponsors from the Canadian Deep Mining Research Consortium (DMRC). The research will be commercialised in 2005.

Jan 1, 2005

Some low grade South Australian iron ores were classified on the basis of their physical characteristics. Ores from Mount Christie and Billeroo are coarse grained mixed ores; Mount Christie ore could be concentrated by gravity or dry magnetic separation at 10 mesh, but Billeroo ore needed to be crushed minus 36 mesh. Ores from Razorback Ridge and Wilgena Hill are fine grained mixed ores; ore from Wilgena Hill could be concentrated by flotation, but poor results were obtained on Razorback Ridge ore. Malcolm Creek ore is non-magnetic and crystalline, and can be concentrated by flotation, but the deposit is small. Ores from Grants Quarries and Peeralilla Hill are nonmagnetic and earthy and could not be satisfactorily concentrated.INTRODUCTIONThe Geological Survey of South Australia has for several years been undertaking a systematic study of the iron ore resources of the State (excluding the Middleback Ranges) in relation to their geology, reserves, and beneficiation. As part of the latter phase of the investigation samples of the ores have been submitted to The Australian Mineral Development Laboratories (AMDL), and it was the study of these samples which provided the material for this paper.The mineragraphic and metallurgical work was undertaken by several officers of AMDL and the results are contained in unpublished reports submitted to the South Australian Department of Mines. Field data published here was obtained from unpublished reports by G. F. Whitten, Senior Geologist, Iron Exploration, of the Geological Survey of South Australia.

Jan 1, 1964

The importance of timbering, not only from a financial point of view but from an actual mining point of view, is so often overlooked or slightly glossed over by the average expert and investor, that I have thought it would prove interesting to go into the matter and to invite discussion upon the subject. We will first take small veins, or reefs as they are termed in some mining countries; and by small veins it is intended to denote fissures from a few inches to three feet. The ore body is supposed to be confined within well defined walls free from gangue matter, unless the casing can be defined as such. Now, if the walls are smooth and moderately hard, no timbering is required other than the stulls, which are braced from wall to wall in order to form platforms or stages to stope from. Should the reef from wall to wall prove payable, or should the vein be of a character to prohibit cleaning or sorting; and it be determined to send the whole of the stone to the, reduction works, the stuUs should be left in place until the section or block of ground is worked out, in order that if a weak spot in the walls (especially the hanging) occur, it would be possible, without any particularly extra expense or difficulty often times accompanied by danger to brace and secure the slabs. After the block became entirely stoped, it would pay where labour was cheap to remove the majority of timbers to stull another section.

Jan 1, 1901

Despite a long history of production of industrial minerals and rocks, New South Wales still offers significant opportunities for exploration for and development of these minerals. Exploration for opal, sapphires, and zeolites in the State has been particularly encouraged by pioneering geological studies by the Department of Minerals and Energy, which have resulted in the development of important new geological concepts and exploration techniques. Large areas with potential for these minerals have not yet been tested. In the case of sapphires, the studies have identified a new type of deposit which is'the source of most of the sapphires mined from alluvial deposits. Recent price increases for heavy minerals, a re-evaluation of previous exploration in coastal regions, and a recognition of suitable environments in inland New South Wales have stimulated renewed exploration both onshore and offshore and have led to increased production. Significant potential also exists for development of a number of other minerals, including: topaz, which occurs in large, unusual and perhaps unique deposits in northern New South Wales; dimension stone (particularly granite); bentonite; diatomite; and silica for metallurgical use. Potential also exists for development of construction material resources, particularly construction sand, which is in short supply in the Sydney region.

Jan 1, 1989

The following is a brief summary of the Bulli Colliery and its method of operation when Australian Iron and Steel Ltd. took control.Bulli Colliery is situated about a mile west of the village of Bulli and is some 10 mUes north of the Australian Iron and Steel Company's Steelworks at Port Kembla.The mine is owned by Australian Iron and Steel Limited, who purchased it in 1936 from the liquidators of Bulli Colliery and Coke Works.It is one of the oldest working coal mines in Australia, having been opened about 1858 and has worked more or less continuously since that date.The seam worked is the No. 1, or Bulli, Seam, which outcrops along the escarpment of the Illawarra Range and is generally operated by tunnels, the portal at Bulli being some 440ft. above sea level.The colliery holding is fairly extensive, but the coal seam over a large portion of the area within two miles of the outcrop has been more or less destroyed by an intrusion of basalt.At present there is no coal being worked within a distance of about 21 miles from the surface, the farthest workings being about four miles from the tunnel mouth.The existing main haulage road, for the first two miles from the portal, is not straight; it is very narrow over fairly long stretches and has many changes of grade varying from 3% in favour of the load to 13% against the load.The dumping station and screens are situated close to the portal of the haulage tunnel, and at this point the coal is loaded into railway hopper waggons, which are then hauled by rope to the top of a self-acting incline. The waggons are lowered down the incline, a distance of approximately! mile, the ruling grade being about 18 %.From the bottom of the incline, waggons are hauled by Company's steam locomotive to exchange sidings from whence they are taken by New South Wales Government Railway engine to the Company's Steelworks at Port Kembla.

Jan 1, 1947

The cyclone, or centrifugal separator, ,is firmly established in industry as a low cost separator of solids from gases.While it will also separate fluids of different densities, and solids from liquids, its main use is to remove relatively fine dusts from gases whose pr~erties are generally not greatly different from those of air. This latter phase of operation is the one that will be dealt with here.The duty of such a cyclone separating system is to take in a supply of dusty gas and separate it into its components of dust and clean gas as perfectly as possible for the least consumption of pressure head. Any separation at all causes pressure loss and, in general, the greater the separation, the greater the pressure drop needed to effect it. The percentage of dust in suspension which is separated from the gas-dust mixture is commonly called the collection or separation efficiency. Overall or "true" efficiency must take pressure drop into account and may be considered as proportional to the ratio of the percentage of dust collected to the resultant pressure drop. For any cyclone It will vary with different dusts.Many commercial adaptions of the simple cyclone are made solely on the basis of pressure drop improvement, without taking into account the effect on separation efficiency, probably because the latter is so difficult to assess correctly. It appears unfortunate but true that the majority of such adaptions and patent gadgets fitted to cyclones which decrease pressure drop, do have an adverse effect on separation. In other' words, the true efficiency is seldom increased but often diminished.Without a knowledge of what actually goes on inside a cyclone, it is impossible fully to appreciate the real effect of a modification. For instance, it is on record that a cyclone...

Jan 1, 1949

By McLeod RL

The Tolukuma gold-silver prospect is located approximately 100km N of Port Moresby in the Central Province of Papua New Guinea (PNG). Epithermal "adularia-sericite" style mineralisation crops out over 1200m within an en echelon quartz veined zone 1 to lOm wide. At a 4g/t cut-off grade, a geological resource of approximately 1.47Mt @ 13.77g/t Au is indicated from 38 diamond drill holes completed since discovery by Newmont Pty Ltd in September 1986. At a regional scale, Tolukuma miner- alisation appears localised in a dilatant zone at the intersection of a 1150 magnetic structure, and the western margin of a N-S trending graben which is filled by a Pliocene volcanic complex contemporaneous with the Mt Davidson Volcanics 30km to the W. A l0km diameter circular Landsat feature, which may reflect magma emplacement at depth, occurs immediately N of Tolukuma and nearby mineralisation. Mineralisation at Tolukuma occurs in sub-vertical quartz veins at, or adjacent to the faulted contact between Pliocene basic and intermediate volcanics/intrusives, and quartz mica schists and phyllites of the Cretaceous Kagi Metamorphics. Most veins display evidence of multiple episodes of brecciation and textures indicative of cyclic boiling, including crustiform rhythmic banding and quartz pseudomorphs after platy calcite.

Jan 1, 1991

The subject of government involvement in industry is, to say the least, a touchy one. For many it conjures up thoughts of socialisation or nationalisation. For others it is a desirable objective and is seen as a means of social reform by giving government a greater say in the control and distribution of human, financial and natural resources for the betterment of the community. Whatever your point of view, it is difficult to deny that government involvement exists to lesser or greater degrees in all industries. The mining industry is no exception and the degree of government involvement is probably greater than it is in other industries. I think it is important to remember when talking about government involvement in industry to recognise that there are different types of involvement and that all governments have a right, if they so desire, to become involved in whatever way they choose. The decision of a government to increase its direct or indirect involvement must, of course, be taken in the national interest. Governments, if we are still old fashioned enough to believe in ministerial and electoral responsibility, must make up their own minds about whether their actions are in the national interest and they must be prepared to accept the consequences of that action, good or bad. For instance, they must decide

Jan 1, 1975