Search Documents

By Creasey J. W, Huntington J. F

Faults cutting the Lithgow and Katoomba seams in some collieries of the Western Coalfield can be classified, on the basis of spatial pattern, into three principal groups: meridional swarms of closely spaced minor faults and associated joints, with throws of less than 0.5 m and with exceptional faults of up to 5 m; isolated interswarm strike-slip faults in the Lithgow seam and widely spaced strike-slip faults in swarms in the Katoomba seam; and low-angle normal faults associated with the Lidsdale-Lithgow seam split.Orientations of faults and coal cleats in the coalfield are presented on stereoplots and histograms, as a basis for an analysis of fault dynamics. The low-angle normal faults were found to have been formed only along the Lidsdale-Lithgow seam split, and before the high-angle faults. The origin of the high-angle normal faults in the meridional swarms is discussed and it is suggested that basementcover interactions must have occurred. This suggestion is supported by geophysical evidence. Low-amplitude monoclines in the coal seam, and the spacing of swarms 0.9 to 4.5 km apart, may be due to the underlying basement structure.It is clear that postextensional compressive deformation of swarms in the coalfield gave rise to shortening by minor thrust development, and probably also caused the synchronous strike-slip movement on pre-existing normal faults. There is evidence to show that isolated interswarm strike-slip faults in the Lithgow seam, and widely spaced strike-slip faults in the Katoomba seam, may have originated synchronously with such thrusts. The axis of maximum principal compression ('71) for the thrust event was inferred to be near horizontal and aligned approximately E-W. Recent rock mechanics measurements of the present day stress field indicate a similar stress configuration.

Jan 1, 1981

By Parkes DB

The excavation of sandstone of generally medium strength for the Liverpool Link Line by Dosco Mark 2A Roadheaders has demonstrated the versatility and good performance of road- headers in suitable rock formations. A description is given of the strata traversed by the tunnels together with descriptions of equipment and crews, excavation sequences, operating difficulties and the results achiev- ed. In addition tunnel construction is des- cribed for a difficult section where there was only O.Sm clearance between invert and a four lane vehicular tunnel below, and O.5m clearance between tunnel crown and a century old sewer above.

Jan 1, 1976

CENTRAL mine ore consists mainly of galena and marmatite in a siliceous and rhodonitic gangue, the average assay values being approximately 11.5 oz. per ton Ag, 14.5% Pb, 14.5% Zn, 1.3% Ox Pb, 0.3% Ox Zn.Owing to the 1923 fire in the underground workings, much of the ore now being mined has been subjected to a certain amount of oxidation, as shown by the oxidised values above.This factor is of great importance from a flotation point of view, as a sulphide surface which has been subjected to the influence of oxidation is not as amenable to flotation concentration as a fresh sulphide surface. The importance of this factor is increased when a differential flotation is to be made, and, as in the case of Central mine ore, the sulphide, which is to be floated first, has been oxidised...

Jan 1, 1931

The Australian Constitution specifies certain powers of the Commonwealth Government to be used in its capacity as the national government. Certain of these broad powers result in the Com- monwealth having a facility to play an important part in the development of the mining industry. The State Governments, however, by virtue of their wide powers to regulate matters within the boundaries of a particular State, are more directly involved in the day to day administration and standards of activities of mining operations. In this respect the Common- wealth has something of a dual role because of its "State-like" responsibilities for the mainland Terri- tories. The components of the role that the Common- wealth Government discharges in relation to the mining industry are qualified to varying extents at particular times by the political persuasion of the Government. In absolute terms the components are as follows. 1. Economic management. The Commonwealth's fiscal and monetary policies have an important effect on industry as well as on State finances. In particular, the taxation regime employed by the Commonwealth Government is of direct importance to economic decision-makers in the mining industry. 2. International matters. International trade and commodity matters are, more and more, becoming an everyday part of the conduct of a nation's foreign affairs. 3. Exports. The Commonwealth Government, via the constitutional powers over overseas trade, have exercised varying degrees of control over mineral exports to achieve particular objectives. 4. Foreign capital and investment. Australia in general, and the mining industry in particular, is and will continue to be a net importer of capital. There appears to be bipartisan political agreement in Australia that foreign investment policy must be enunciated to ensure that investors. are in no doubt that Australia welcomes beneficial investment and technology from overseas. 5. Environment and Aborigines. Governments, both Commonwealth and State, have in recent years become more involved in these areas in response to their interpretations of community aspirations. 6. Energy. Access to assured supplies of energy is now viewed, by Governments worldwide, as a desirable asset to ensure the well-being of a nation's people and industries.

Jan 1, 1978

By A Hanna

Quarries around Auckland have reached or are reaching the ends of their lives, which raises issues about rehabilitation. Significant volumes of 'cleanfill' are generated by the City, particularly during phases of urban renewal and development. Emplacement of the fill in quarries removes the problem of fill disposal and provides an opportunity for restoration of the quarry site.There is a compatibility between quarrying and cleanfilling because at quarries:Truck routes are already established Neighbours are accustomed to the effects and appropriate buffer distances have been established Bringing fill into a site attracts aggregate sales and is very efficient. Fill originates from construction sites and ad-hoc excavations and therefore it is not surprising that sampling has shown the quality to be variable. Both Winstone and the Auckland Regional Council have surveyed undisturbed soils in the region to attempt to determine natural background levels of common contaminant substances. Comparison of these levels with delivered fill shows that a high proportion of delivered materials can be regarded as mildly contaminated. Therefore the term 'cleanfill' is, in the Auckland region at least, a misnomer and the term 'managed fill' has been adopted.Historically and presently the only control on quality of 'cleanfill' has been some visual inspection. This leaves the fill operator open to potential liability for creating a contaminated site. Implementation of controls at WinstoneÆs operations has progressed slowly, over some ten years. This is mainly due to the perception that mobility of contaminants within and out of the landfill will be very limited because of the near-neutral pH and abundance of clay minerals in the fill. The methods of control and results of environmental risk assessments at WinstoneÆs Puketutu Island Quarry will be briefly described.

Jan 1, 2002

The drilling and evaluation of bore cores provides the best available statistical basis for characterizing a coal prospect. Important, long-term decisions by management frequently must be based on the results. The majority of coal mined presently is used for steam raising or the production of metallurgical coke. Common bore core tests and analyses appropriate to this usage can be cate- gorized as non-destructive, chemical, physical, petrographic, caking/plastometric and propert- ies of non-coal material. The major tests within each category are described. Certain specific information from the bore cores is required by the coal geologist, mining engineer, coal preparation engineer and the user, either individually or as a group. The optimal bore core evaluation test pro- gramme is the one which satisfies the needs of all the professional disciplines with the grtatest speed and at minimal cost. The principal steps in such a programme are listed. There is an urgent need for a bold new Australian standard to provide the necessary guidelines to an industry which at present lacks uniformity in its approach to the task.

Jan 1, 1977

A process was developed based on the thermal hydrolysis and precipitation of iron from solutions resulting from the leaching of zinc plant residue. A study was made of the hydrolysis of iron, at temperatures in the range 140-220°C, in both pure solutions of ferrie sulphate and in leach solutions derived from plant spent electrolyte.At 200°C hydrolysis of pure ferric sulphate solutions results in the precipitation of ferric oxide, Fe2O3, at low acid. concentrations, and a basic salt, Fe2O3.2S03.H20, at hIgher acid concentrations. At 180°C ferric oxide is precipitated at low acid concentrations, but at higher acidities. carphosiderite, 3Fe203.4SO.3.9H20, is the stable phase. Frequently a mIxture of ferric oxide and carphosldente IS produced at 180°C, the ratio of phases being dependent on the non-equilibrium experimental conditions.With solutions derived from plant spent electrolyte hydrolysIS at elevated temperatures results in the precipitation of jarosite compounds of the type NaFe3(S04)2(OH)6 The precipitation of natrojarosite jarosite, and ammonio-jarosite was studied in detail. Temperature, free acidity, and the concentration of sodium potassium, and ammonium ions are critical factors which affect the extent of precipitation.A process based on ammonio-jarosite precipitation was tested in a pilot plant.An alternative method of iron removal based on the addition of zinc oxide calcine, to neutralize excess acidity, and the precipitation of ferric oxide was also tested in the pilot plant. Both processes appear economically favourable...

Jan 1, 1967

By d&apos, Alton AJ, Rigden DT

Modern petroleum refining offers a complexity of environments, each requiring different metals for the satisfactory performance of-the various sections of the refinery, and this paper first outlines the varied enva.x¦on-ments thus met.It follows that the metal types in use will also vary to suit each particular environment, and the paper' consequently covers the use of ferrous-metals, ranging from plan carbon steels to the high alloy types and the non-ferrous metals, particularly copper and its alloys.The failures of some,of these metals and alloys are then illustrated by experiences it Kwinana. These failures are duo to (a) corrosion, (b) erosion, (c) faulty welding, and (d) mechanical defects,' of which the first is by far the most prevalent. The protective measures taken to prevent subsequent failures are then given under one or other of the following headings :(1) alterations in process conditions, (2) the use of alternative ,alloys,(3) suitable heat treatment, (4) redesign of the failed section, (5) cathodic protection, and (6) use of corrosion inhibitors.Reference is then made to the use of specialised metals and alloys.Metals, generally in the form of oxides or salts, are also used as catalysts in refining processes. Activated alumina is used, combined with silica .forScracking' of heavy oils, and as a support -for platinum, cobalt, molybdenum, nickel and similar metals, which catalyse hydro-genation and dehydrogenation-processes. .In the final formulation of petroleum products metallic compounds may be added. Reference is made to the large quantities of lead used by the petroleum industry and to the use of metallic soaps and detergents in the formulation of lubricating oils and greases.

Jan 1, 1962

The influence of pulp potential on the flotation behaviour of sulphide minerals in laboratory batch flotation tests is discussed in terms of self-induced flota- tion, collector-induced flotation, and depression.' Assuming that the pulp poten- tial is controlled by the same factors that determine the genuine redox poten- tial, an attempt is made to interpret the experimental results in terms of potential-dependent reactions based on bulk thermodynamic data. Self-induced flotation is displayed by many sulphides in moderately oxidizing solutions but not in reducing solutions. The available evidence suggests that the hydrophobic entity could be sulphur produced by superficial oxidation of the mineral but this has not been established beyond dispute. In general, flotation is observed near the potentials at which sul- phur would be expected to form and the minerals which produce sulphur seem to float the most strongly. Collector-induced flotation is most conveniently studied on minerals which have only slight self-induced floatab- ility. The mineral-collector interaction is potential-dependent hence flotation is generally only observed in limited ranges of potentials. While the general form of the floatability-potential relationship is similar to that predicted from thermody- namic data close correspondence between predicted and experimental results is not always observed.

Jan 1, 1984

The Perth Mint receives gold and silver from various sources for evaluation and refining. The metals are received in many forms and vary widely in assay. Refining is carried out using the Miller Process and the and the resulting market quality bullion is sold in a range of weights and alloys to suit the international bullion market and public demand. INTRODUCTION The Perth Mint was established in the late nineties as a branch of the Royal Mint, London, to refine the gold from the newly established gold- fields in Western Australia. The branch was opened for business in June, 1899. After refining, the bulk of the gold was used in the manufacture of sovereigns and half-sovereigns. Nowadays, although most of the gold received comes from the W.A. goldfields, some gold is deposited by producers in other states and in Papua-New Guinea, as well as scrap and trade wastes from manufacturing jewellers and old jewellery from the general public. Silver is deposited in the form of old silverware, recoveries from-photographic processes etc. Gold or silver may be lodged at the Mint in person, through a bank or other agency or by registered post. Telegraphic advice is usually given when gold is sent by the latter, so that insurance may be effected.

Jan 1, 1982

This paper comprises a discussion of standards for comparing conditions in mines, of methods for measuring the flow of air, of a comparison of fan performances, and the application of these matters to mines in Western Australia.UNDERGROUND CONDITIONSIn approaching the question of mine ventilation one naturally searches for some standard by which to measure the conditions in a mine.There are several clauses in the Mines Regulation Act defining the conditions which are permitted. The quantity of CO2 is limited to 0·25 by volume, but the estimation of CO2 involves a chemical determination and is not suited for general use in a mine.The maximum temperature is fixed at 87 0 F. (dry bulb), and at 80° (wet bulb). The reading of temperature is easily done in the working places, and this is a very valuable and practical test of the conditions in a mine.The wet bulb temperature is probably the most important factor in determining working conditions. It is obvious that human life cannot be sustained for any appreciable period if the wet bulb temperature is above blood heat (about 97°F.). In places where the wet bulb temperature is 90°F. there is danger of heat stroke.In places where the air in a mine is still, the wet bulb temperature rises to a value close to the rock temperature.Adequate ventilation cools the workings by transference of heat from the rock to the air stream, and the temperature...

Jan 1, 1939

By Spark R. F

The copper deposits at Pernatty Lagoon are predominately djurleite-digenite bodies beneath the permanent water table, and chrysocolla-atacamite-malachite above the permanent water table. The minerals havebeen deposited as sheets, lobes, and pods in zones suggestive of permeability channels or permeability basius with respect to groundwater circulation.Pyrite is deposited in the form of framboids, which reflects its biogenic origin. Copper-iron sulphides deposit by replacement of pre-existent pyrite, and rarely by direct deposition. The latter mode of formation results in complex crustification bandings of chalcopyrite, bornite, sulphur rich bornites, digenite, and blue remaining covellites. The copper-iron sulphides appear to reequilibrate under constrained oxidation, resulting in an iron depletion and associated copper enrichment, the final product of which is a djurleite-digenite assemblage and associated with goethite. Where copper mineralization/ host rock relationships have rendered the rocks entirely impermeable to post ore groundwater movement, then the copper-iron sulphides are preserved as the ore assemblages.Minor and trace minerals observed include sphalerite, carrollite, galena, wittichenite, and possibly tetrahedrite in the primary ores. In the oxidized ores cllprite, tenorite, and trace brochantite have been found.

Jan 1, 1976

The purpose of this paper is to outline the current status of financing in the Australian Gold Mining industry and to discuss a number of developments that have occurred during 1983/84.Recognising the importance of equity financing various equity issues, including project valuation, will be discussed against the backdrop of an industry experiencing both rapid growth and a changing structure.Nothwithstanding the current tax exempt status of the industry there is a trend towards more debt financing. A number of financing issues will be covered and it will be shown howvalue can be created through astute financing planning.

Jan 1, 1984

A philosophy is presented that new graduates in mining and metallurgy should be equipped to use computers during their under- graduate courses, should be aware of the capabilities and costs of a wide range of computing equipment, and should receive sufficient stimulus to become involved in applying computers for the benefit of the mineral industry. A program is presented in which computer applications and "hands on" involvement with computers are integrated into the progressive stages of the undergraduate courses in Mining and Metallurgy. In this respect, the role of the computer is to assist the student by performing time consuming tasks, to demonstrate the industrial applications of computing, to extend the scope and complexity of the tutorial, assignment and project work which can be undertaken by the student, and to provide the essential first stepping stones toward continued useful involvement with computers during the graduate's working life.

Jan 1, 1977

By S Barrow, D Kent

Controlling the access of equipment, and people, has become more critical over the last few years for improving productivity and to meet safety responsibilities imposed by legislated obligations to have safety management systems. Hence Mine Site Technologies (MST) has spent the last three years completing the development of the tagging system to meet the mining industryÆs requirements, particularly streamlining access control. The basic tagging system tracks active Tags carried by personnel, or attached to vehicles and equipment, within underground zones. These Tags are detected (read) by Beacons placed strategically throughout the mine. As a Tag, or Tags, go past a Beacon they are read and the information transmitted back to the main database PC. This allows the current whereabouts of personnel and equipment to be known, as well as the history of their movements. The objectives of implementing the TRACKER Tagging System at Oaky No 1 Coal Mine were to: maintain a count of personnel inbye a particular point, and can alarm when a pre-set number is reached (eg the limit imposed by availability of SCSRÆs, etc); maintain a count of vehicles (and vehicle type) inbye a point, and can alarm if when a pre-set number is reached (eg when rated diesel units exceeds the limit for the ventilation present in that zone); manage the vehicle fleet, by keeping track of various vehicles underground better control and dispatch management of the equipment is achieved; keep track of equipment, knowing the location of equipment (such as forks, baskets, pumps, fans, etc) where last used or stored will minimise the risk of losing gear and assist in keeping inventory to a minimum; and locate personnel in emergency situations, by placing read Beacons throughout the mine the location of all personnel can be known in real time so that in the event of an emergency, their withdrawal can be monitored.

Jan 1, 2005

By Nemick JA

Recent advances in computer simulation together with field measurements of caving and microseismic activity about longwall panels, has allowed a much better understanding of the caving process and the variability due to geology. The joint research between SCT Operations and CSIRO Division of Exploration and Mining has initiated new methods of computational modelling predicting various caving patterns and strata failure far ahead of the longwall face. This work was validated by field measurements of caving and microseismic activity at the longwall face.The rock fracture distribution and the caving characteristics of a range of strata sections have been simulated by computer methods. Validation studies of the method were addressed together with case studies. The interaction of caving with support convergence and face control is presented. The method allows the simulation of longwall support behaviour under various geological conditions. The system also allows a prediction of the monitoring data, which is best suited to give an early warning of weighting events or signal various key caving characteristics.

Jan 1, 1998

Every automatic citizen is an automatic recipient of a miner's right under the present Mining Act (Chapter 195), but this alone does not entitle any automatic citizen to mine for minerals on any land, even his customary group's land. Without complying with requirements of the Mining Act, any automatic citizen who engages in mining solely on the basis of a miner's right would be mining illegally. He would also be engaged in illegal mining if he mines on customary or other non-government land. Even if mining is legally pursued by an automatic citizen, he does not acquire ownership of minerals without first making the required royalty payments to the State.

Jan 1, 1991

By P J. Chapman

Recent catastrophic failures of tailings storage facilities (TSFs) continue to highlight the need for a detailed understanding of failure modes and the defences that are in place within the design to mitigate the failure modes. However, in many cases the instrumentation devices and monitoring approaches selected during operation do not link back to the design defences and inappropriate or redundant instrumentation is often installed. Candidate instruments and monitoring approaches (critical controls) are presented and matched to critical failure modes, with clear linkages to the intent of each instrument/monitoring approach. Commentary on where complementary measurements with independent technology types are recommended to provide greater assurance of trends to the design engineer or TSF owner is also presented. In response to the recent TSF failures, an increasing focus is being placed on instrumentation and monitoring relating to slope instability and safeguarding against the potential for static liquefaction, using a critical state soil mechanics framework. To support selection of appropriate zoning within a stability model, three complementary devices are recommended – vibrating wire piezometers to provide an indication of pore pressure and allow the phreatic surface to be inferred, tensiometers to confirm the presence of unsaturated conditions (and hence low potential for undrained failure) and moisture content sensors to provide an indication of void ratio, and hence state parameter, in saturated zones. The combination of VWPs and tensiometers will provide complementary measurements in the saturated and unsaturated zones, and also provide information on the extent of any near-saturated zones, provided that sufficient instruments are installed.

Jul 1, 2021

Reconciliation of the ore reserve has been an integral part of mine planning since Bougainville Copper Ltd. commenced mining operations at Panguna in 1972. Confidence in the ore reserve is considered essential, both for long term planning of the deposit, and for fair and accurate reporting of the mining resource to shareholders. Recoverable, proven reserves are published annually. Although the ore reserve quoted is based only on diamond drill hole (DDH) information on a 122 metre by 122 metre grid, predictions are regularly reviewed against production. Concentrator results are taken to be the best estimate of grade and tonnage. Surveyed mined perimeters and average blasthole grades are reconciled at the end of each month against the concentrator figures. Predictions of the in-pit reserve are made using an orebody model. DDH and blasthole (BH) sample grades are used to make predictions for both long and short term planning. This paper describes how reconciliations are used to validate ore reserves at Panguna. Development of the orebody model is described, and some of the difficulties encountered in doing reconciliations are addressed.

Jan 1, 1987

By P Stoker

The need for quality assurance and quality control (QA/QC) in the sampling and assaying of minerals is fundamental to the reliability and confidence of a mineral resource estimate, reserve estimate and possibly profitability of a mine. In spite of this, QA/QC practices in the mining industry are commonly applied poorly, or misunderstood. As New Leaders, we should aim to correct the poor practices and become fully informed on appropriate procedures. This paper uses worked examples that show the usefulness and importance of best practice QA/QC procedures. Fundamentals of reviewing the performance of the laboratory by examining the results of client inserted standard reference material (standards), blank material and duplicate samples are discussed. To do this, three examples from Australian data sets have been used. For each example, simple and efficient plotting techniques are suggested with subsequent evaluations of each plot. The first case study compares the results of internal standards from a laboratory with blind standards (where the expected value is unknown to the laboratory) submitted by the client. It was demonstrated over time that the laboratory was unintentionally analysing the internal standards in a different manner to the remainder of the sample batch. In this example, not understanding the cause of a high negative laboratory bias could have led to poor understanding of the depositÆs grade and in the extreme a proposed mining operation may have reached operational stage with a subeconomic grade. The second case study discusses the quality of blank material submitted by a mining operation to monitor cross-contamination within the laboratory. The blank material contained background levels of the element under investigation. This created uncertainty in the assay results, which could have led to the need for additional assays and drilling programs. Finally, the third case study demonstrates the use of the relative paired differences (RPD) technique to cross-validate the results from duplicates and repeat analyses from two laboratories. The three examples given show either laboratory or operational error. If left undetected, each example could have had serious implications for the mineral resource estimate and ultimately, the mining operation. These examples are not isolated occurrences; poor QA/QC practices are an industry wide problem exacerbated by rapid staff turnover and increased contractor positions on-site. New Leaders must be equipped with a thorough grounding in QA/QC best practices to improve its application and confidence in the results of sample analysis.

Jan 1, 2009