Search Documents

By B E. De Gee, N Viviers, A Naidoo

In 2013 the Mopani Copper Mine Mufulira plant in Zambia embarked on a project that was aimed at improving concentrator recoveries. The project commenced with the automation of the milling and flotation circuits. This involved the installation of new instrumentation, namely measurement devices and actuators, and the connection of these to new programmable logic controllers (PLCs).The infrastructure changes were followed by the implementation of basic proportional-integral-derivative (PID) controllers on the PLCs. Supervisory control and data acquisition (SCADA) interfaces were also implemented to allow for switching between controller modes, inputting of setpoint variables and to provide a visual display for process monitoring. The final phase of the project involved the installation and commissioning of advanced process control (APC) solutions on the milling and flotation circuits. This work was carried out by Mintek over 21 on-site days. The APC solutions included the MillStar and FloatStar suites of advanced controllers.The MillStar control suite focused on stabilising the mill feed and mill discharge on the two primary mills as well as the flotation circuit feed. Mintek’s CyLas instruments, which provide a measurement of the hydrocyclone underflow angle, were also installed. The measurements were incorporated into the discharge stabilisation control on both milling circuits. The FloatStar level stabiliser controller provided flotation cell pulp level control on fourteen cells, including two columns.Performance tests showed that the Mintek APC system stabilised the mill feed and mill discharge while ensuring the process remained within operational constraints. The MillStar control system utilised the CyLas instrument to prevent roping on the hydrocyclone underflow. This was not always achieved under normal operation. Additionally, the flotation section was stabilised as a result of improved level control by the FloatStar control system.Performance comparisons showed that the Mintek control system improved the operation of the milling and flotation circuits resulting in a greater copper recovery.CITATION:Naidoo, A, De Gee, B E and Viviers, N, 2014. Implementation of an advanced milling and flotation control system at Mopani Mufulira copper mine, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 363–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Eupene GS

The valuation of exploration properties which contain no identified resources or reserves is the most subjective of all valuation tasks likely to be carried out by a geologist. The geoscience rating method proposed by Kilburn (1990) recognises this inherent subjectivity but also attempts to apply some discipline to the valuation process. Some other methods used for valuations of this type clearly lack discipline and are open to misuse and abuse. The Kilburn method essentially requires the practitioner to justify all aspects of the valuation process. The valuer must specify and, more importantly, quantify aspects which enhance or downgrade the intrinsic value of each property. The intrinsic value is called the ""base acquisition cost"" (BAC) and it represents the average cost to identify, apply for and retain a base unit of area of title. The BAC and base unit of area both vary with different types of exploration and mining title but remain constant for similar types of titles in the same mineral tenure regime. In the Kilburn Method the enhancement/ downgrading factors are determined by the geotechnical prospectivity (Kilburn Method) within the title. A modified version of the Kilburn Method presented here (""Modified Kilburn Method"") also focuses attention on other real variables besides the geotechnical attributes which influence valuations of this type, viz., competition for tenure and activity in the markets in which the exploration properties are being traded. The most active such market at present is the stock market. By utilising uniform BACs and base units of area (for similar titles) for all exploration properties (in practice in Australia this is only possible within a particular State or Territory), the method exposes the valuer's opinions of each of these variables to the scrutiny of the investor. The investor (or his professional adviser) is afforded the opportunity to directly compare valuations on different properties by different practitioners and can assess how the final valuation is weighted in respect of geotechnical prospectivity, competition for tenure, and stock/financial market sentiment. No other method currently employed in Australia to value mineral exploration properties affords the investor this `luxury', which some may argue is their right.

Jan 1, 1994

By P E. H Gregg, D Horne, R B. Stewart, N Bolan

The Tui mine site is situated on the NW flank of Mt. Te Aroha, at approximately 400 m altitude. During underground mining operations two lead-copper-zinc ore bodies were exploited and processed on site. The legacy of the mining operation is a barren dam containing over 100 000 mm of sulphide-rich tailings. The Tui mine site is arguably the worst case of environmental degradation resulting from past mining activity inNew Zealand. Although the impacted area (approximately 4 ha) is extremely small by international standards, acid mine drainage (AMD) emanating from the abandoned tailings dam and mine adits has severely contaminated local streams and prevented natural plant recolonisation of the site for more than 20 years.   The suitability of the tailings as a potential plant growth medium was assessed with the end view of revegetating the tailings dam and alleviating AMD. This paper outlines characterisation work conducted on the tailings and summarises preliminary results from plant growth trials. The tailings contain up to 5% Fe, 1.15 % Pb, and 0.45% Cu in the form of sulphide minerals. The distribution of heavy metals, sulphate and total sulphur with depth indicates that the top 200 - 300 mm of the tailings have been extensively weathered since their deposition. The oxidation of sulphide minerals, particularly pyrite (FeS2 ) has reduced the pH of the tailings to nearly 2 in places. Below 300 mm the sulphide minerals are largely unweathered and the theoretical acid generating potential of the tailings exceeds 170 Mg CaCO3/1000 Mg tailings at certain depths. Plant growth trials were conducted to study the effects of lime and organic matter addition on the establishment of vegetation on the Tui mine tailings. Several plant species were assessed including some cultivars bred for their tolerance of heavy metals.

Jan 1, 1995

By H Cifuentes, D J. Williams

Despite the recognised importance of tailings management, there remain little data on the potential benefits of biological treatments compared with physical and chemical treatments. The operation of the majority of tailings storage facilities (TSFs) continues to employ mainly physical solutions, such as sub-aerial tailings slurry deposition, with increasing adoption of thickening, paste and filtration to dewater the tailings involving the addition of chemicals such as flocculants and coagulants. However, with tailings production continuing to escalate rapidly due to the increasing demand for commodities and reducing ore grades, available technologies have not demonstrated cost-effective performance at high tailings production rates. This paper examines the emerging role of bacteria to better manage tailings, reducing risks and optimising storage capacity. Bacteria have the potential to enhance tailings dewatering, maintain their permeability, delay the onset of desiccation cracking, and improve their shear strength. Bacteria-treated tailings may be suitable for use as construction materials. Bacteria also have potential in limiting the dusting of tailings and facilitating rehabilitation on closure. The paper describes a series of laboratory involving the addition of harmless bacteria to a range of tailings. The bacteria form a compact material called calcite (a common and stable form of calcium carbonate), which immobilises the tailings particles, releases water, and cements the tailings in a stable and natural matrix. The water released can be recovered or evaporated, depending on site objectives. The bacterial reactions are linked to physical and chemical processes, providing the potential for an optimal mix of technologies for particular tailings and site conditions.CITATION:Cifuentes, H and Williams, D J, 2018. Potential improvement of tailings geotechnical behaviour using bacteria, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 228–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

A low grade, refractory ore gold mine with high striping ratio such as at Macraes is always challenged in ways to improve margins. Common practice approaches used at OceanaGold Ltd Macraes are to maximise grade delivery, optimise recovery and reduce unit costs, as well as take any opportunities to incorporate new technologies and implement enhanced commercial strategies.   The Business Improvement (BI) programme was implemented across the Macraes operations in late 2003 and is being rolled-out to all other parts of the business. The core focus of BI at OGL is to: +        increase revenue, +        reduce cost, and +        improve processes.   A dedicated BI team comprising of a manager, team leaders and business analysts were engaged to identify and manage a series of opportunities to reduce operating expenses, optimise capital outlays and generate extra revenue. The Business Improvement Programme, though in its formative phase, has begun a cultural change within the organisation. Many people are starting to challenge the way they do things and are looking for ways to continually improve business performance.   The BI team encompasses individuals from different departments who can offer the diverse skill set necessary to produce intended results. The current team is made up of a BI manager, BI Team Leaders in Mining and Processing and analysts from Mining, Processing, Commercial and Plant Maintenance workgroups. A team member has recently been formally trained as a Six Sigma Black Belt. ] The BIÆs team role is to assist in the establishment of project management processes for each improvement idea. In addition the team will assist in tracking implementation, identifying and unblocking restrictions and limitations as well as setting up metrics to quantify the level of benefit returned and sustained.   From a more strategic point of view, the BI team is advancing the Business Improvement capability of the company by developing long term Communication and Training strategies. These strategies will set the direction of BI initiatives in the years to come to: +        educate the OGL workforce in basic BI techniques, +        assist the OGL workforce in applying basic BI techniques, +        communication the direction of BI in OGL, and +        close the information feedback loop to facilitate transparent communication between the OGL workforce and the BI team.

Jan 1, 2004

Mineralisation adjacent to Herberton occurs within three main subcentres. The Her- berton Hill subcentre is characterised by the association of Sn,W the Herberton Dividing Range South subcentre by Sn, and the Herberton Dividing Range North by Cu, As. The relation- ships between the subcentres are discussed in terms of metal distribution, production, deposit types, wall rock alteration and re- lationships with granitoid intrusives. The temporal and three dimensional spatial re- lationships between the centres are uncertain.

Jan 1, 1978

By G R. Howard, G Back

Management of information systems for data collection is essential to maintain data integrity and continuity, and manage loss control on a large world-class mine such as Telfer Gold Mine. This paper aims to describe the individual systems and protocols of geological data capture at Telfer, then focus on Quality Assurance Quality Control data as an example of loss control in practice. Loss control systems are required to provide capacity, flexibility, structure and management tools to enhance data interrogation. The data that have been collected can then provide geological, financial, environmental, and contractual information to optimise management of business best practice. Telfer Gold Mine is a wholly owned and operated subsidiary of Newcrest Mining Limited. The mine is located in a remote area of NW Western Australia, and has been operating for 20 years. Geological data have been collected at Telfer since 1973. The data include drilling, assay, geological, survey, structural and geophysical data. Data management has evolved through many systems with data stored on many different hardware and software platforms. Commencing in 1995, collation, standardisation and validation of the historic data was completed. This has resulted in the first Access based drill hole database incorporating all available drilling data. This drill hole database, now hosted in SQL Server, is the hub for all geology related data management systems. The Telfer Gold Mine Geology Department has developed a series of inter-related database systems in order to manage the core geology business issues. Databases relating to drill hole planning, drill contract management, geological logging, accounting (standard costing, forecasting, invoice reconciliation), quality control (QAQC), and environment rehabilitation have all been developed to manage loss control. Management effort to provide adequate data systems and protocols has driven the system from concept to utilisation. The improved productivity, data integrity and data analysis capabilities provided by the new database systems at Telfer have allowed for greater confidence in decision making. Systems such as the drill hole and QAQC databases, when utilised in the proper manner provide up-to-date data analysis for resource audits and contract negotiations. The loss control systems are essential to maintain confidence in data integrity and hence directly effect the future of mining at Telfer.

Jan 1, 2000

The C.S.I.R.O. acid alumina process employs the essential steps of digestion, hydrolysis and calcination to produce pure alumina from ores too high in silica or too low in grade for the Bayer process. The two latter stages have been described in some detail previously but the digestion stage requires separate discussion since ores vary widely in composition and reactivity. Kaolinitic clays require roasting to 800°C to render the alumina soluble in the 11 per cent sulphuric acid used in the process while some ferruginous laterites require roasting to reduce the reactivity of iron minerals.The iron content of pregnant solutions is kept at a low figure by digesting at temperatures where the solubilities of ferric oxide or basic ferric sulphates are small. A two-stage, counter-current digestion is necessary to extract a high percentage of alumina from the ores and to produce a basic pregnant liquor with an SO3 : AI 203 ratio of 1'\1 suitable for high temperature hydrolysis. The second stage of digestion, called the modification stage, treats slightly acid liquors with excess of ore in the temperature range 1200-1400C.The first stage operates at 170°-1900C to extract further alumina from modification residues, using recycled acid obtained from later steps of the process. Both temperature ranges are critical for economic operation and for proper control of the iron content of solutions. In batch experiments, 30 min is regarded as a suitable retention time for digestion and modification; ores which require much longer than this are less suitable for the process. Impurities such as silica, and titanium and vanadium oxides are discarded in the residue along with iron oxide, and do not contaminate the final product. Bivalent metallic sulphates such as MgSO4, can build up in the circuit to a very considerable degree without affecting product purity.Comparison with other processes shows that the C.S.I.R.O. process is superior for control of contamination by iron, which is the major problem in acid processes. The pure intermediate product (3Al203.4S03.9H20) is also more convenient for calcination to alumina than the hydrated aluminium sulphate usually recovered in other processes. Detailed cost comparisons must await pilot-plant evaluation of the C.S.LR.O process.

Jan 1, 1964

By S Norman

The Water Delivery Alliance (WDA) was established to design, construct and commission the pump station and desalinated water delivery pipeline to link the desalination plant on the Kurnell Peninsula (constructed by others) with the existing distribution network at Erskineville, Sydney, Australia. The WDA consisted of McConnell Dowell Corporation Ltd (Macdow), Bovis Lend Lease Pty Ltd (BLL), Kellogg Brown and Root Pty Ltd (KBR), Worleyparsons Ltd (WOR), Environmental Resources Management Group Inc (ERM) and Sydney Water Corporation (SWC).Sydney’s Desalination Project is one of the initiatives to secure Sydney’s water supply against the effects of climate change, population growth and drought. The desalination plant, 100 per cent powered by renewable energy, can supply up to 250 million litres of water per day (mld), which is up to 15 per cent of Sydney’s water needs. The project involved the construction of an 18 km pipeline with an ultimate capacity of 500 mld to accommodate any future increase in the output of the desalination plant.The Alliance procured three full-face tunnel boring machines (TBM) from Herrenknecht AG to construct the 6.5 km of tunnel that would provide a conduit for the DN1800 welded mild steel cement mortar lined (MSCL) pipeline at a number of locations along the route. Nineteen shafts and 16 tunnels were required to complete this work.Crucially one of the TBM drives involved construction of a tunnel into Botany Bay under protected marine life habitats; enabling the connection of the MSCL water carrier pipeline into the dredged section of pipeline underwater, approximately 800 m off-shore in Botany Bay.This paper details the retrieval of the 17.4 m long TBM from the ocean floor upon completion of the Botany Bay tunnel allowing for subsequent use on the Project. Elements covered in the paper include the 835 m tunnel, design and construction techniques for the tunnel and recovery, and details of the methods used to install the DN1800 water carrier pipeline.

Mar 8, 2011

By T F. McConachy, B I. A McInnes, R A. Binns

Within the last decade, major research discoveries have been made in the submarine realm of magmatic and hydrothermal activity of arc-backarc systems in the southwestern Pacific. These include identification of numerous particulate-poor, gas-rich (CO2-CH4) hydrothermal plumes emanating from arc front volcanoes, actively forming porphyry-copper-gold style mineralisation, and new backarc spreading systems erupting alkali basalt-trachyandesite magmas. Major goals of these studies have been identification of modern analogs to ancient volcanogenic massive sulfide ore bodies, and quantification of the volatile fluxes though supra-subduction zone systems.

Jan 1, 2002

Following a period or small-scale activity a joint venture was formed between Ceramco Limited of New Zealand and Georgia Kaolin Company of USA. The initial concept was to process clays for the paper industry but it soon, became apparent that insufficient markets were attainable for the grades of china clay that could be produced for an economic unit. Ceramco Limited acquired the Georgia Kaolin interest in 1975 and proceeded to search for a market, of markets, that would: 1. utilise the unique properties of the product, and 2. enable a viable operation to be created. This paper describes the mineral deposits, the process, the properties of the product, and the marketing methods of New Zealand China Clays.

Jan 1, 1984

Effect of Activated Carbon on the Leaching of Cobalt-Rich Ferromanganese Crust in Sulfuric Acid

Sep 13, 2010

By D J. Williams, G W. Wilson, S, A B. Tran

A comprehensive field program was implemented to evaluate the internal structure and hydrology of two full-scale waste rock piles. The excavation of waste rock dumps for in-pit disposal at the two mine sites provided an opportunity to characterise the in situ properties of the dumps given contrasting geologic and climatic settings. The internal structure and materials within the dumps were observed and sampled as the waste rock piles were being excavated and placed in the open pits for permanent closure. The field program was designed to fully characterise the structure and material properties of the waste rock. The alteration of the material by physical and chemical weathering was also observed. Samples were analysed for paste pH, water content, grain size distribution and geochemistry. In situ density and matric suction were also measured. Soil water characteristic curves and saturated hydraulic conductivity were measured for representative materials. These properties were used to predict seepage pathways through the waste rock and the resulting outflow geochemistry using the finite element model SEEP/W. The materials in the dump at Site 1 were predominantly fine-grained in texture and highly weathered. The presence of dipping beds with alternating coarse and fine materials was evident throughout the profile of the dump. The structure of the waste rock appears to have an impact on the hydrologic pathways within the waste rock pile. The material in the dump at Site 2 was found to be competent and resistant to particle size breakdown. The particles range in size from clay size to large boulders with the median particle size being approximately 125 mm in diameter. The coarse-grained texture of the waste rock resulted in a loosely packed arrangement of coarse particles with little matrix material infilling the pore spaces between the coarse-grained particles. Seepage modelling for Site 1 was completed to predict seepage paths based on observed structure and hydraulic properties measured in the laboratory. The modelling showed that materials with a fine grain size distribution become the dominant pathways for flow through the waste rock pile. The modelling also showed that layers with high silt and sand contents are subject to the highest flow rates. Finer grained clay rich layers have a low hydraulic conductivity and do not convey large volumes of water. Alternately, coarse gravel and cobble materials are unsaturated under values of matric suction that approach the residual water content of the material and do not transmit liquid water. The seepage modelling together with the results of the geochemical analysis show that the dominant particle size that receives the most fluid flow and flushing ranges from fine sand to silt, corresponding to materials with air entry values ranging between 5 kPa to 50 kPa.

Jan 1, 2003

By P Duuring

Late-Archean banded iron formation (BIF)-hosted deposits in the Yilgarn Craton of Western Australia are less well understood compared to the larger Paleoproterozoic, Superior-type BIFhosted deposits of the Hamersley Province. The Weld Range greenstone belt, in the Murchison Domain of the Yilgarn Craton, hosts two Archean, high-grade deposits, Madoonga (68 Mt resource at 57.7 wt per cent Fe) and Beebyn (62 Mt resource at 59.6 wt per cent Fe, ASX announcement 2008). Five main types of high-grade (>55 wt per cent Fe) iron mineralisation at Weld Range each display characteristic grades, tonnage, and contaminant levels, which affect exploration strategies and beneficiation methods:1. ‘Residual’ ore formed as a result of two generations of hypogene alteration of BIF. The first alteration phase replaced silica-rich bands with siderite and/or Fe-rich dolomite; the second phase involved the removal of carbonate gangue minerals and the concentration of residual Fe oxide-rich bands in the BIF via volume reduction. The product is a high-grade, high-tonnage Fe orebody, with minor contaminants.2. Magnetite-bearing shear and fault zones cut BIF along lithological contacts. These zones of secondary magnetite formed as a result of the addition of hypogene magnetite via the circulation of Fe-rich, hypogene hydrothermal fluids through BIF. This type of mineralisation produces narrow (low-tonnage), high-grade magnetite-rich ore zones with high levels of contaminants (eg SiO2, Al2O3) due to the difficulty in mining these zones.3. Specular haematite ± quartz-bearing shear and fault zones cut residual orebodies and magnetite bearing structures. They share similar characteristics to magnetite-bearing structures.4. Goethite-haematite supergene ore zones are controlled by brittle faults that cut BIF. These faults promoted the flow of supergene fluids through BIF and resulted in large ore zones with variable Fe grades and contaminants.5. Detrital deposits comprise transported BIF fragments and are intensely goethite-haematite supergene-altered. These orebodies are locally extensive, with moderate Fe grades.

Jul 11, 2011

By Jackson E

The general level of awareness amongst members of the professions that they are faced with an increasing number of claims for breaches of their professional duty was dramatically heightened by the decision of Rogers J. at first instance in Cambridge Credit Corporation v Hutcheson (1985) 3 ACLR when the auditors of the failed company were found liable for breach of contract and faced a damages award of $145 million - well in excess of their insurance cover. No comfort should be found in the fact that this decision was overturned on appeal, for that result rested on the issue of whether there had been a causal connection between the breach of contract which had occurred and the loss suffered rather than on the fundamental principle of auditors' liability.

Jan 1, 1989

By Little T. N

The Western Australian School of Mines is continuing to investigate the blasting techniques and mining strategies that are used for ore/waste separation (or high grade/low grade ore separation) or to prevent ore and waste mixing. The aim of all the mining strategies is to produce an optimum product. The optimum product is one which contains no diluent and undergoes no mixing of the various identified ore and waste blocks and is fully recovered at the minimum overall operating cost. The current study includes the use of computerised Knowledge Based Systems (KBS) technology to assist the user with the blast technique selection and blast design process. These aspects are highly dependent on the geology. (geometry, rock mass properties, grade distribution), explosive performance and the expectations of the mining company in terms of production rates and equipment utilisation. Most of these factors are not well defined and nor are they easy to quantify. However, a large amount of knowledge does exist and is available in the following forms: rules of thumb, empirical formulae, engineering judgement and past experience. KBS techniques are well adapted to handle such"forms of knowledge. The primary objective of this paper is to illustrate an approach for the use of Knowledge Based Systems during the analysis and interpretation stages of the blast design process. In particular, the components and methodology of the developed system are described for selective open pit gold mining. The Knowledge Based System developed was written using the declarative programming language PROLOG.

Jan 1, 1990

By Y Wang

Inadequate goaf gas control may lead to gas exceedances in the ventilation return air, which will trip power in longwalls and cause production stoppage. To effectively control gas emissions, Australian mines heavily rely on drilling vertical goaf holes to capture coalmine methane before it migrates to mine openings. The wide application of goaf gas drainage may change the goaf pressure distribution, lead to more ventilation air leakage, and consequently increase gas explosion and spontaneous combustion risks. This paper focuses on analysing goaf gas drainage production data from a case study longwall mine in Australia. The correlation between suction pressure, total flow rate, gas flow rate and air leakage rate were analysed in detail as the face-to-hole distance changes. Suction pressure is found to be positively correlated with total flow rate, and their correlation also varies at different goaf locations due to various goaf compaction and flow resistance. This paper also proposed a theoretical method to calculate the goaf resistance of ventilation air leakage pathways. Based on several basic assumptions and different goaf drainage scenarios, the leakage airflow pathway resistance in the goaf at different face-to-hole distances can be calculated. The model results suggested that the resistance of air leakage pathways from the working face to individual goaf holes increased with the face-to-hole distance. The resistance results can also be used to calculate the corresponding permeability at the same position, which can be used as input data for CFD or Ventsim models.

Oct 12, 2022

By Pirvics AI, Whitworth NR, Tuppurainen JMI

Process control applications to the unit operations in both the Lead and Copper Smelters are reviewed. The basic aim of this control is to smooth plant inputs to produce an output of consistent quality in terms of chemical composition, temperature and physical properties. Most effort has been put into the process bottlenecks, namely in the process baghouse of the Lead Smelter and in the Copper Smelter reverberatory furnaces. The method of approach is discussed, firstly extensive plant measurement and data logging plus identification of factors which most affect the unit operation and secondly control of these factors to smooth out variations. This has been possible due to the development in-house of on-line instruments to measure the critical variables and the external use of computers for plant control. Some of these instrument developments are also briefly discussed.

Jan 1, 1984

By D H. Bell

Slab-buckle failures in coal sequences involve thin slab deformation in strata dipping parallel to the footwall, and are a consequence of both unloading and the weak nature of the thinly bedded rock mass. Methods of modelling and predicting such occurrences include: +        a conceptual model using a base friction table, +        a mathematical model using the Euler solution for column and beam bending (after Goodman, 1980), and +        computer analysis techniques such as UDEC (Universal Distinct Element Code after Cundall and Hart, 1993).   Slab-buckle failures have the potential to seriously disrupt production because of their volume and rapidity, and to endanger both equipment and personnel working on the pit floor.   In July 2004 a large slab-buckle failure occurred overnight after a new batter and bench had been formed at the Malvern Hills Opencast Mine in inland Canterbury. This involved the entire length of the pit (85m along strike) when a 2m thick intact slab with a total volume of ~3500m3 translated down dip 6.2m on the base of a thin coal seam to form a pronounced buckle at the toe. The coal measures consist of finely laminated mudrocks with multiple coal seams of varying thickness dipping ~45¦ to the southeast, and the opencast mine had been designed with footwall batters formed parallel to bedding with a vertical bench separation of 15m.   Back analysis of the Malvern Hills failure was necessary to investigate the controls on footwall instability, and for future mine design. An engineering geological model was created and samples of the slab material and failure surface were collected and tested to establish the required parameters for use in the Euler solution for column and beam bending. Back analysis using the Euler solution provided unrealistic results that overestimated the overall length of a stable slope by more than 10 times.   No further large scale slab-buckle failures have developed at the mine site, in part because of the slow rate of coal extraction, but precautionary drainage of the footwall slopes has been undertaken to improve overall batter stability. The location of the slab-buckle failure on a critically positioned pre-sheared thin coal seam with full hydrostatic head is considered the most probable cause of the July 2004 failure, rather than inherent instability of the generic bench and batter arrangement adopted. The use of a precedent-based engineering geology approach to future mine design is considered the most appropriate solution in the circumstances.

Jan 1, 2007

By M I. Pownceby

High temperature roasting studies on chrome-spinel contaminated ilmenite concentrates showed that sulfur, introduced through a sulfidising roast treatment, selectively reacted with the chromium in the spinels. The roast treatments were carried out in a laboratory scale rotating drum kiln using a standard Becher-style heating profile (10 h, 1075ºC), char as the reductant, and variable amounts of added elemental sulfur (0 - 3 wt per cent).After roasting, bronze-coloured grains were visible representing chrome-spinels that had undergone selective sulfidisation. SEM imaging of the products showed that sulfur was preferentially concentrated in ~5 - 15 µm thick rims fully enclosing the chrome-spinel grains. The sulfur-rich rims became a sink for manganese (Mn) from the ilmenite resulting in the rims being rich in Cr-Mn-Fe-sulfides. Quantitative electron probe microanalysis of phases present within the rims identified two sulfide phases. The first sulfur-phase (S-phase) was low in Mn (1 - 3 wt per cent) and high in Fe, Cr and S, while the second S-phase was considerably higher in Mn (30 - 35 wt per cent Mn) and lower in Fe and Cr. The dramatic change in the composition of the chrome spinels after sulfidisation is likely to significantly alter their physical properties (eg hydrophobicity, conductivity, etc). This should make their physical separation from the ilmenite potentially easier than roasting/magnetic separation methods.

Oct 5, 2011