Search Documents

Jan 1, 2004

An enhanced gravity concentrator was installed in conjunction with an intensive leach reactor at the Sadiola plant in Mali last year and commissioned in December 2007. There has been much debate over the years as to the effect of gravity concentration on overall plant performance. The late Dr Laplante suggested that for every ten per cent of gold recovered by gravity, there was a corresponding 0.1 per cent to one per cent additional overall plant recovery. The results at Sadiola are consistent with this hypothesis with an overall four per cent gain in plant recovery. With total gold recovery of 12 per cent in the gravity section, grades are increased from 3.54 g/t in the gravity feed to an average of 2 600 g/t in the concentrator feed to the inline reactor. The recovery of gold in the inline reactor is in excess of 98.5 per cent. This paper discusses the background to the project, the laboratory test work prior to the equipment selection, the operational results of the system, as well as the benefi ts of the future application of high mass yield centrifugal concentrators in base metals, sulfides and industrial minerals. Bench scale, pilot scale and plant practice examples are also presented.

Aug 1, 2010

By M Fylak, R Wenda

Advanced preparation techniques open new ways for SEM and X-ray diffraction (XRD) investigations on hydrating cementitious systems. In this paper the early time hydration of Portland cement is studied with advanced cryo scanning electron microscopy techniques in combination with in situ X-ray diffraction and heat-flow calorimetry. The application of preparation techniques and analytical methods to Portland cement hydration are presented and discussed. Some aspects of hydration reactions are focused. The reaction products of the first minutes, changes in ettringite morphology, AFm formation during the deceleration period and the visualisation of C-S-H microstructures were special points of interest. X-ray diffraction analyses and Cryo-SEM images gave essential information about phase development, reaction kinetics, microstructure and morphology of hydration products. Portlandite, AFt and AFm phases were detected by in situ XRD. Cryo-SEM analyses enabled high resolution imaging and EDX-analyses of cement particles and reaction products. The results of the different analytical methods were compared to obtain detailed information about crystallisation processes and microstructural development during the first three days of Portland cement hydration.

Jan 1, 2008

By Xu Z, Hu C

An attempt has been made to investigate the performance of green pellet formation of the Daye magnetite concentrate from the weak-magnetic separation plant. The optimum conditions for the commercial production of green pellets was found through experimental research. The satisfactory size range for balling is 75 ¦ 3 per cent -200 mesh. The suitable moisture content is between 8.7 and 9.1 per cent and the optimum amount of bentonite added is between 1.5 and 2.5 per cent. The emphasis is on the size of the feed materials since the grinding fineness, which can be obtained at the plant, at most is 78 per cent -200 mesh. If the optimum fineness for the pellet formation is above this value, this means that the concentrate must be re-ground before balling. The results from experiments showed that a good quality green pellet can be attained by using materials below 78 per cent -200 mesh, which provides a strong foundation for the commercial production of green pellets.

Jan 1, 1999

By Y Li, S Ramazan, E Topal

A mine waste dump progression plan can provide a clear outlook of the mining operation. To produce such an output requires detailed placement schedule of the mined material, including the volume (or tonnage) and the allocated dumping location. However, current practise mainly focuses on the ore production, over-simplifying the waste material scheduling. As a result, a rock dump is often treated as a single point in long-term planning, making it difficult to predict the waste dump progression pattern over the life-of-mine. Without such a guidance, it is almost impossible to carry out progressive rehabilitation on the waste rock dumps. The lack of dumping schedule could cause delay in development construction, ie tailing storage facility and run-of-mine pad. Other downstream effect due to the over-simplification is inaccurate estimation of required truck hours, which could have huge financial impact on the operation.In this paper, mixed integer programming (MIP) models of different objective functions, ie maximise truck productivity by minimising the overall haulage distance, minimise required truck deviation between adjacent years, and a hybrid between the two objectives, are utilised to generate the long-term optimum rock placement schedules under the criteria of satisfying site specific conditions. All three MIP models are implemented in a large scale open pit mine. The numerical solutions from the models forms three different rock placement schedules, based on which, the yearly truck requirements are easily calculated and compared. The graphical results show the three corresponding waste dump progression patterns over the life-of-mine, providing the optimised long-term forecast of the operation.CITATION:Li, Y, Topal, E and Ramazan, S, 2014. Optimising the long-term mine waste dump progression and truck hour schedule in a large-scale open pit mine using mixed integer programming, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 335–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By J Millard, K Sexsmith

BHP Billiton Diamonds Inc (BHPB) has been mining kimberlite from several pipes at the Ekati Diamond MineTM located 300 km north of Yellowknife since 1997. Processing of kimberlite produces coarse kimberlite rejects (CKR, 0.5 to 8 mm) and fine tailings (less than 0.5 mm). The CKR are trucked to the Coarse Kimberlite Reject Storage Area (CKRSA) located within the drainage area of the tailings impoundment (Long Lake Containment Facility û LLCF). The coarse rejects are wet when dumped and are expected to freeze as a result of annual average site temperatures of about -10¦C. Seasonal thawing occurs along the exposed edges of the pile. Monitoring of the CKR indicates they have consistently low sulfur concentrations (0.4 per cent) accompanied by high acid neutralisation potentials (78 to 337 kg CaCO3/t). Carbonate concentrations vary from 0.9 per cent to 3.4 per cent. The CKR are therefore not potentially acid generating based on conventional laboratory testing. Monitoring of stagnant pools on the tundra downgradient of the CKRSA has shown that water originating from the pile resembles acid rock drainage (ARD). Water pHs can be less than 4, and sulfate concentrations are typically in the thousands of milligrams per litre. Conventional flowing toe seeps are pH neutral but also have elevated sulfate concentrations. Investigations conducted in the summer of 2002 revealed no evidence of in situ acid generation. Pore water chemistry is probably controlled by oxidation of fine-grained pyrite, neutralisation of acidity by calcium and magnesium carbonates and silicates, and freeze concentration of pore water. The acidity observed in tundra pools downgradient of the CKRSA appears to be a result of leaching and mobilisation of iron under reducing conditions at the CKR-soil contact. Downstream of the CKRSA, reduced iron oxidises and is hydrolysed on contact with the atmosphere causing pH depression. BHPB is applying the findings of this study by constructing facilities containing kimberlite on granite pads. These in turn are placed on frozen ground so that the foundations remain frozen and limits contact of wastes with the acidic soils.

Jan 1, 2003

Separation of Iron Particles from Banded Haematite Quartzite (BHQ) Ore by Selective Magnetic Coating The separation of fine iron particles from banded hematite quartzite (BHQ) has been studied using selective magnetic coating. The BHQ ore assays as 38.9 per cent Fe, 42.5 per cent SiO2 and 1.0 per cent Al2O3. Mineralogically, the ore contains hematite and quartz as the major mineral phases where as goethite and magnetite is present in minor entities. Natural magnetite of very fine size and oleate-magnetite in colloidal form, prepared synthetically in the laboratory are used as the coating material on the surface of hematite particles. The selective coatings of oleate-magnetite on BHQ surfaces followed by magnetic separation studies have indicated that, it is possible to achieve 62.3 per cent Fe with 8.5 per cent SiO2 at 85.4 per cent iron recovery. The recovery of iron values is found to be superior in comparison to the conventional magnetic separation techniques. The selectivity of coating for enhancing the magnetic response of iron particles is achieved by controlling the surface properties of the particle via electrokinetic potential adjustment by controling pH and addition of oleate-magnetite. In the separation process, the effects of pH, magnetic intensity and addition of oleate-magnetite are studied to achieve the maximum grade and recovery of iron values. The optimum separation is observed at pH of 7.5, oleate-magnetite concentration of 0.25 ml/g of BHQ ore and a magnetic intensity of around 0.8 Tesla. The X-ray diffraction (XRD), Infra-red spectroscopy (IR) and UV-visible spectroscopic studies strongly suggest preferential coating of magnetite on hematite surfaces. Scanning electron microscopy (SEM) studies have brought out the semi-quantitative features of BHQ ore. The recovery of iron values from a lean grade ore such as BHQ is carried out looking into the future needs of this ore in India for iron and steel making.

Sep 13, 2010

By G Mudd, N Haque, S A. Northey

Life cycle assessment (LCA) provides an internationally standardised framework for estimating the environmental impacts associated with products or services (International Organisation for Standardisation, 2006). A particular strength of LCA is the ability to consider indirect impacts that occur at different stages of a product’s life (eg raw material acquisition, manufacture, use, disposal or recycling) and through its supply chain (Figure 1). A wide variety of impact categories are able to be considered by LCA, such as the potential contribution to global warming, ozone depletion, marine eco-toxicity or freshwater eutrophication.CSIRO has a long history of using LCA to compare the environmental impacts associated with alternative mining, mineral processing and metal production technologies (Haque and Norgate, 2014; Norgate and Haque, 2012, 2013). These ‘mine-to-metal’ assessments have primarily focused upon estimating embodied energy and greenhouse gas impacts associated with these production processes; however, more recently there has been a refocus to also consider consumptive water-use impacts in more detail (Northey et al, 2014).CITATION:Northey, S A, Haque, N and Mudd, G, 2016. Water-related data requirements for improved life cycle assessment of mining, mineral processing and tailings management, in Proceedings Life-of-Mine 2016 Conference, pp 16–18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

The formation and distribution of gold placers in active collisional mountain belts are directly related to the tectonic, topographic, climatic and erosional constraints prevailing on either side of the orogen at the time of placer formation. In the absence of pre-existing placer deposits, these factors combine to concentrate placer development on the side of the orogen facing the prevailing winds, where most of the erosion and uplift occurs. Drainage network changes and glaciation can significantly alter placer distribution with respect to source areas within the orogen. After collision stops, placer formation will proceed on both sides of the orogen as exhumation of the mountain belt ensues. Incorporation of pre-existing placers formed on ancient mountain belts into younger placers in subsequent orogens, may be recognised by anomalous placer distribution compared to the above model. Most of the relatively young giant placers such as those inNew Zealand, Chile, Bolivia and Columbia, exhibit these general patterns. Their character and mode of formation have important implications for the formation and distribution of much older placers, such as those in South Africa's Witwatersrand Basin.

Jan 1, 1996

Open pit mining has considerable damaging effects on the environment of the mining region. These harmful influences have to be controlled during mining operation until mine closure. Different sections of mined land, such as; pit(s), waste dump(s), tailing pond(s), roads, areas for onsite facilities and free land zones which are not mined, have to be reclaimed through treatment of environmental pollution and implementation of a permanent post mining land use (PMLU) after mine closure. Implementation of a permanent optimal post mining land use (OPMLU) is one the most decisive criterion which effects on reclamation procedure, mine closure and their costs. Therefore to define ultimate pit limit (UPL), mine closure and reclamation costs should be entered in the calculation iterations same as the other variable costs of the projects. Estimation of closure and reclamation costs of a mining project is carried out based on the attained OPMLU and the specifications of the mine site. In this paper, a model is developed to provide OPMLU for pit area through fuzzy multi-attribute decision making (FMADM) technique. The model was implemented on a hypothetical copper mine in northwest of Iran as a case study. Lumber production was selected as OPMLU for the pit area. It is finally concluded that through the developed model, OPMLU for different sections of mined land in an open pit mine project is defined. Also closure and reclamation costs are estimated based on the defined OPMLU to achieve a more accurate UPL.

Dec 6, 2010

By M I. Pownceby, C M. MacRae, A Torpy

Electron probe microanalysis (EPMA) and quantitative X-ray diffraction (QXRD) techniques are capable of providing high-quality quantitative information regarding the phase mineralogy and distribution of alumina within iron ore samples. The techniques, however, use different methodologies in determining the mineralogical information (ie structural versus chemical), which introduces some limitations. In this study, EPMA was used to identify and quantify the deportment of alumina within mineral phases in iron ore samples (-1 mm crushed) sourced from different suppliers. Results were directly compared with quantitative mineralogical data derived from QXRD to provide an evaluation of the relative merits of both techniques. The four ores studied contained alumina either in the form of gibbsite, aluminosilicates (eg kaolinite), or associated with goethite.For minor phases, gibbsite and kaolinite, the abundance trends measured via QXRD were generally reflected in the EPMA data. Agreement was less satisfactory for the more abundant goethite phase (both low- and high-Al forms). The discrepancy may be the result of sampling issues arising from textural features such as grain size, and also a systematic overestimate in the amount of Al-rich goethite when hematite and Al-bearing phases are finely intermixed and the EPMA step size is coarse. A second difference in the EPMA results compared to the QXRD data was in regard to quantification of low-Al and high-Al goethite phases. The sensitivity of the chemical-based EPMA was better for distinguishing between high- and low-Al goethite although the results remain overprinted by potential errors introduced via sampling.Care should be taken when directly comparing results from each method, although in general the data should be considered complementary, as each approach provides slightly different results and interpretations regarding the overall mineralogy.CITATION:Pownceby, M I, MacRae, C M and Torpy, A, 2017. A comparison of X-ray and electron-based analysis techniques for characterising the mineralogy and alumina distribution in iron ores, in Proceedings Iron Ore 2017, pp 593–598 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By D Garcés, M Meléndez, R Castro, E Viera

Enhancing the understanding of gravity flow in caving operations is a key factor in the design, operation and success of caving methods. Consequently, much research has been performed to increase knowledge about gravity flow. Many valuable theories have been gained from different research approaches, which include physical modelling, numerical modelling and a limited number of full-scale tests. Recent advances in technology have allowed Codelco Chile to carry out trials using Smart Markers technology. This technology was used in Esmeralda mine’s Block-2 at El Teniente mine from August 2012 to January 2015. This paper aims to determine the characteristics of the extraction zone and obtain the data that will allow greater understanding of gravity flow for design and draw control purposes.The collected data from recovered markers were analysed using a linear interpolation of both the initial position of the markers and drawbell accumulated drawn tonnage. For each drawpoint in the trial, the regularity or irregularity of flow was analysed based on the recovered markers and the drawn tonnage. Correspondingly, the relationship between flow characteristics and observed fragmentation in drawpoints was analysed. The gravity flow of the Smart Markers revealed that current drawpoint spacing provides the interaction conditions of adjacent flow zones. However, it is possible to increase the drawpoint spacing while allowing caved rock to be extracted from the major and minor apexes.The results of this research also verified that full-scale test data are the predominant factor in the production level design and production control at El Teniente mine.CITATION:Garcés, D, Viera, E, Castro, R and Meléndez, M, 2016. Gravity flow full-scale tests at Esmeralda Mine’s Block-2, El Teniente, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 349–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

This backgrounds the methods, and technical terminology, of digital image processing techniques used to write out remote sensing imagery.

Jan 1, 1983

By A D. Campbell, G R. Power

Many caving mines use numerical flow models to simulate mine production, forecast recovered ore grades and optimise the draw strategy. In sublevel caving (SLC) mines, the effects of blasting and fragmentation at an individual ring scale generally cannot be included in these models. Previous attempts to use results from marker recovery trials to calibrate numerical flow models have been limited due to difficulties in accounting for blasting effects at a ring scale. This paper outlines how an empirical criterion for blasting and fragmentation was used to attribute variable flow properties into a numerical flow model based on the blast design and modelled fragmentation. The flow model was then validated using data from a number of full scale marker recovery experiments. The result of this approach was a significant improvement in forecast accuracy when compared against the same modelled cave marker recovery without the inclusion of these blasting effects. Improvements in the flow model are currently being adopted within the mine scale model to further improve the accuracy of grade forecasting, optimise the draw strategy and increase net present value. The integrated modelling approach is also being used to simulate the effects of different drill and blast designs on cave recovery. It is suggested that, if implemented, the technique would lead to improved blast designs in other SLC mines, increase the value of marker trial data and reduce costs associated with large scale blast design trials.CITATION:Campbell, A D and Power, G R, 2017. Improving calibration of flow models against SLC marker trials by linking blasting effects to particle mobility, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 11–22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By L B. Zhou, S Li, B L. Wang, S B. Li, Q Wang

The rapid development in ChinaÆs metal mine resources has caused a series of mine environment problems such as serious ecological damage and environment pollution, and secondary geological disasters. The paper has reviewed ChinaÆs metal mine development, including current status and environmental situation, analysed existing problems in mine development and environmental management, and proposed corresponding countermeasures and suggestions.CITATION:Wang, B L, Li, S B, Li, S, Zhou, L B and Wang, Q, 2012. Current situations, problems, countermeasures and suggestions for ChinaÆs metal mine development, in Proceedings Life-of-Mine 2012 , pp 353-356 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

Western Deep Levels, a seismically active deep level gold mine, started placing backfill in their narrow tabular workings as part of the regional support strategy in 1986. Over the years the percentage of working places being backfilled has been gradually increasing. At the end of 1995 the support efficiency and the labour productiveness relating to support installation were scrutinised to determine if resources were being optimised. Owing to financial, safety and productivity constraints it was decided to redesign stope support to be less labour intensive, safer and provide an integrated stope support system. This new integrated system will thus combine the previously used temporary, permanent and back area support consisting of mechanical props, hydraulic props and backfill respectively. Backfill previously formed an integral part of the regional support in conjunction with strike stabilising pillars. To design the integrated support system the backfill placement quality has to be exceptionally good and placement must be done as close as possible to the working face. The backfill to face distance was reduced by 30 per cent and in some areas by more than 50 per cent with an increase of square metres filled to increase the effect of the backfill even more. This paper addresses the design and successful implementation of an integrated stope support system based on the optimisation of backfill to the extent where installation of mechanical and hydraulic jacks could be eliminated.

Jan 1, 1998

By D R Van Eck

Western Deep Levels, a seismically active deep level told mine. stalled placing backfill in their narrow tabular workings as part of the regional support strategy in 1986. Over the years the percentage of working places being backfilled has been gradually increasing. At the end of 1995 the support efficiency and the labour productiveness relating to support installation were scrutinised to determine if resources were being optimised. Owing to financial, safety and productivity constraints it was decided to redesign stope support to be less labour intensive, safer and provide an integrated stope support system. This new integrated system will thus combine the previously used temporary, permanent and back area support consisting of mechanical props, hydraulic props and backfill respectively. Backfill previously formed an integral part of the regional support in conjunction with strike stabilising pillars. To design the integrated support system the backfill placement quality has to be exceptionally good and placement must be done as close as possible to the working face. The backfill to face distance was reduced by 30 per cent and in some areas by more than 50 per cent with an increase of square metres filled to increase the effect of the backfill even more. This paper addresses the design and successful implementation of an integrated stope support system based on the optimisation of backfill to he extent where installation of mechanical and hydraulic jacks could he Eliminated

Jan 1, 1998

By W Taylor, S Chen, R Haywood, M White, R West, J Ranasinghe

In March 2012 a combined BHP Billiton and Hatch team embarked on a program to improve the concentrate burner efficiency of BHP Billiton’s Olympic Dam copper flash smelting furnace. A multi-faceted approach including an analysis of the furnace using operational knowledge and first principles engineering led to the design and supply of a new central-lance (disperser). A new, patented, swirl method of introducing the copper concentrate into the furnace was developed to integrate with the existing concentrate burner. Plant trials in 2014 demonstrated an increase of nearly 10 percent in the oxygen efficiency of the furnace. The improved efficiency is expected to provide savings in operating costs and asset life extension of downstream gas and dust handling equipment.CITATION:White, M, Haywood, R, Taylor, W, Chen, S, Ranasinghe, J and West, R, 2015. Improved copper flash smelting at Olympic Dam, in Proceedings MetPlant 2015, pp 382–395 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

Behaviour of Bubble Clusters in a Turbulent Flow

Sep 13, 2010

By A Hollweg, K H. Esbensen, M Lischka

Two new splitter designs for intercepting moving streams of matter are presented, the variable cross-stream splitter (vCSS) and the rotary stream splitter (RSS), which are intended for implementation in a fully automated modus. The vCSS facilitates obtaining up to three subsamples with different splitting ratios from automated laboratory flow paths, while the RSS divides the intercepted sample into 16 equal analytical aliquots. The splitters can process a wide range of dry, granular and free-flowing materials (<5 mm). The required weight for each subsample can be set without mechanical adjustments in the case of the vCSS. Typical applications are subsampling/splitting for X-ray fluorescence pelletisation (or fused beads) or splitting for average shift composite sampling or grain size analysis. The vCSS combines the advantages of riffle splitting (three user-defined subsample masses) with miniature bed blending and can accept up to 15 kg in total incoming sample mass. In practice, the automated vCSS can deal with unlimited ingoing mass fluxes, while the RSS is designed to operate at a user-defined fixed subsampling rate (1/16th in the tested version). Both splitters have the potential to be optimised and evaluated according to an application/user-defined total sampling error (TSE) + total analytical error (TAE) threshold. Both splitters were tested under adverse conditions and with compositions involving three components with properties representing typical mass fluxes and components concentrations in industrial and technological systems: phosphate concentrate 89.00 per cent (<500 µm), slag ten per cent (>2 mm) and glass spheres one per cent (750–1000 µm). The slag particles vary widely in particle shape, aspect ratio and surface roughness, while the glass spheres are extremely prone to bouncing and segregation (spillage). This test system is extremely difficult to split and thus constitutes a realistic worst-case scenario. While the vCSS does not comply strictly with Theory of Sampling demands for correctness, both splitters may well be able to deliver fit-for-purpose representative results if/when tested properly. Average relative mass deviations ranged from 1.89 per cent for phosphate concentrate (relative standard deviations of 20-fold repeated splitting) to 4.72 per cent for glass spheres and 13.04 per cent for slag. For the RSS, the average replication experiment splitting variation was 2.89 per cent for phosphate concentrate, 4.82 per cent for glass spheres and 11.1 per cent for slag. Both new automated online splitters would therefore appear to be able to be tuned to fit-for-purpose representivity (defined here as maximum relative reproducibility <5 per cent) for many non-extreme materials; however, it is always imperative to test every new type/class of material empirically. There is a wide commercial potential for important materials and commodities sectors, including food, feed, drugs (pharmaceutical), secondary raw materials, recyclates, agricultural products and seeds.CITATION:Lischka, M, Hollweg, A and Esbensen, K H, 2017. New online/atline splitter designs for laboratory automation – feasibility results, in Proceedings Eighth World Conference on Sampling and Blending , pp 159–166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017