Search Documents

By N Clarke, A Barros

Preconcentration of run-of-mine subgrade and marginal ore by screening has the potential to substantially improve the economics of mining, particularly for large, low-grade orebodies, and to reduce environmental impacts. It has recently been the subject of a major research effort by a joint public-private research body, CRCORE. Yet despite this, there appears to have been only one fully commercial installation, at Bougainville Copper Limited in the late 1980s. Two reasons for the limited application are that not all ores have suitable properties and the economics of all pre-concentration processes on low-grade materials are highly sensitive to the precise balance of mass and value recovery and to the pre-concentration process cost, including materials handling. These factors make it imperative to have good test data on the process response of feedstock across the orebody. Collecting that data presents major challenges, which differ for green and brownfields operations. This paper first discusses the approach to preliminary evaluation developed by CRCORE, which relies on testing of coarse rejects or drill chips available from exploration drilling programs. This method is an efficient first step in evaluating an orebody which is deemed geologically to be potentially amenable to screen upgrading, but it does have limitations and must be followed by larger scale work. A suite of methods have been developed by the authors as a result of test work since the 1990s on several projects, supplemented by published data, which aim to provide statistically robust data at lower cost than large scale bulk sampling tests. For greenfields projects, the upgrade response measured on material crushed to -53 mm has been found to correlate closely with ROM ore, with no scale-up required for material with upgrade responses in the range of commercial interest. Large diameter whole drill core, such as PQ, is expected to be suitable for this method. As drilling such core is costly, the aim should be to establish relationships between upgrade performance and proxy measurements such as multi-element chemical or hyperspectral analyses. This approach was successful at the Gramalote gold project in Colombia. The method is not applicable for ores with thick vein material comparable with the crush size, but such material is not suitable for upgrading by screening and would be eliminated by the preliminary testing. For brownfields projects where blasted material can be sampled, the upgrade response can be accurately measured by sampling only the finer fraction of the ore, selecting a top size which represents 30–50 per cent or more of the ROM size distribution. This is likely to be between 50 and 100 mm. The much finer size compared with the full ROM ore greatly reduces the sample mass required to achieve a given intrinsic sampling error and enables sample preparation to be undertaken with large-scale laboratory equipment rather than mobile crushing plant. The accuracy of the method can be improved by measuring the approximate mass of oversize rejected during sampling. Some ores do show a systematic deviation from the assumed model fit which results in this method slightly underestimating the upgrade response, and it would therefore still be recommended to take one or two full bulk samples to confirm results before a final investment decision.

Aug 24, 2022

By M T. Grigoleit, M S. Schneider

The iron ore industry in Australia has, in recent years, experienced an unprecedented growth phase. But now that major expansions are moving into the operation phase, new challenges have emerged. Whereas initial planning may involve a few modelling studies, ongoing performance monitoring and improvement requires a different, more intense approach. This is especially important in the face of changing factors such as commodity prices, exchange rates and labour markets. Response time is key. As a mining operation proceeds from initial planning to daily operations, the time window for analysis shortens, going from months to weeks to days as the business matures.Simulation models and analysis tools are typically built and run by specialists in the planning phase, but then what? The investment has been made, but realised only once. What if further analysis could be carried out in-house, re-using existing models using up-to-the-minute data? Can we create virtual mines that run in parallel to live operations that allow computers to identify areas of a value creation or operational improvement? These questions can be answered by the innovative application of big data, simulation and predictive analytics. The future will be having this all integrated into one platform that offers, for the first time, an opportunity for non-experts to apply existing modelling and analysis assets – combined with live data – to deliver support for continuous improvement, and the ability to respond quickly to external changes in the best possible way, before they become big problems. These techniques will represent a step change in the ability for operations to maximise efficiency and will underpin the intelligent operations of the future. These issues are addressed in this paper.CITATION:Schneider, M S and Grigoleit, M T, 2015. Maximising productivity through big data, simulation and predictive analytics, in Proceedings Iron Ore 2015, pp 475–480 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

Traditionally, surface coal mines in the Western United States have been limited by economics to depths between 150 to 200 feet. Utah International Inc., however, is now planning to strip coal its San Juan Mine in Northwestern New Mexico to depths ranging up to 400 feet while uncovering 20 feet of steam coal. This method is cost-competitive with nearby shallower coal deposits and underground mining of the same property. How trucks and shovels can pre-strip for a dragline, along with results of the planning process, comparison with alternate systems, capital requirements, operating costs and comparisons with other coal sources are all detailed. Also discussed are the major problems anticipated, how they might be corrected, and potential improvements to the concept. Introduction The San Juan Deep Stripping Project will be situated at Utah International's San Jean Mine. The mine is in the Four Corners region, so-called because four states enjoy a common border point about 30 miles to the northwest.(see Figure 1). The area is a semi-arid plateau region with an average elevation of 5,200 feet, receiving an average of 6 inches of precipitation annually

Jan 1, 1981

By G Campbell-Cowan

Much has been written about the fact that most transformation efforts disappoint. This paper addresses factors that should be taken into consideration in planning and implementing transformation programs to ensure success.In 2009, St Barbara commenced a transformation program to address issues of chronic poor quarterly operational performance; financial pressure caused by the unreliable operational performance; and an inability to develop business plans with integrity and to reliably deliver on the plans. As a result of a number of years of disappointing operational performance, St BarbaraÆs culture was not conducive to business success.This paper uses lessons learnt during St BarbaraÆs transformation program to highlight key characteristics of change programs that can generate significant sustainable benefits. While there were many benefits from the transformation program, the most significant impacts of St BarbaraÆs program have been transformation of the companyÆs culture and capability of people as business leaders; the establishment of a business systems framework to guide the design and development of systems; and developing support functions, for example centralised procurement and supply chain, business improvement and technical services.CITATION:Campbell-Cowan, G, 2012. Business transformation - Lessons learnt for successful change, in Proceedings International Mine Management 2012, pp 135-142 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By B Rouvray, R Bertuzzi

The development of a design-and-construct tunnelling project in Australia from its concept to its construction requires designs to be prepared and reviewed at several distinct stages prior to documenting ‘for construction’. On recent projects the post-tender stages have been variously called 30 per cent—70 per cent—100 per cent; or concept–substantial–final; or system definition–preliminary–critical. The design is reviewed at each stage by the designer’s internal reviewer, the contractor and its independent advisor(s), the owner and its independent advisor(s), the project’s independent certifier, proof engineers and often third-party stakeholders and their advisors. Documentation for each stage often dominates the design effort, at times distracting from design. This paper presents the authors’ experience of this design-and-review process. Comparisons of design budget and actual design spend and design program implications are presented. It is postulated that a subtle change has occurred in our industry that has diminished the value of the design dollar. Is there a better process? An alternative is suggested.CITATION:Bertuzzi, R and Rouvray, B, 2014. Reducing the cost of tunnel design in Australia, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 501–506 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By S Robinson, A Turner, R Dale, C Butler

"Sandfire Resources NL- (‘Sandfire’) DeGrussa definitive feasibility study (DFS) identified geometallurgy as a major factor in achieving optimum plant performance at the DeGrussa mine. A geometallurgical initiative was created to proactively investigate this issue, and a key initial achievement was the 2013 paper by Condon et al (2013) on developing a working geometallurgical model from first principles. Significant advancements in Sandfire’s geometallurgical understanding since that publication now shape how information is presented and communicated.The main geometallurgical parameters so far identified as critical factors affecting plant performance are Cu:S ratio, iron sulfide mineralogy, talc carbonate content and sphalerite content. Apart from specific mill strategies, geometallurgical issues have been managed through communication between departments and strategic run-of-mine (ROM) pad management.This paper uses the current theories of geological evolution of the volcanogenic massive sulfide (VMS) deposit at DeGrussa, to discuss the variability between the orebodies C1, DeGrussa (sea floor mounds) and C4, C5 (sub-sea floor replacement) to highlight the different issues each orebody is expected to encounter when processing.A zone of altered low-grade mineralisation surrounds the main orebodies at DeGrussa, referred to as a halo. Talc minerals are often patchy within this halo and often cause significant recovery issues during processing. This halo has been successfully modelled using MgO as a proxy. The ability to model the talc material assists with both identifying potentially problematic zones for processing and geological interpretation of the ore deposits evolution.Early in geometallurgy studies at DeGrussa it became apparent that it would be useful to identify processing performance prior to mining. This necessitated the incorporation of specific sulfide species into the mining block model. These attributes are interpolated from the logged sulfide estimates allowing a clear picture of the abundance of each mineral type within a defined area.In conjunction with the block model a geometallurgical factor (GMF) graph was developed, identifying sulfide mineralogy based upon mineral assays. These two recent additions to the model provide a clear picture of the nature of the ore sources that will be presented to the processing plant.The future of geometallurgy at DeGrussa will see these tools used to aid mine scheduling with a view to further improve processing recoveries.CITATION:Butler, C, Dale, R, Robinson, S and Turner, A, 2016. Geometallurgy – Bridging the Gap between Mine and Mill: a Case Study of the DeGrussa Geometallurgy Program, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 77–88 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By MJ SMITH

For the past 150 years, drilling and blasting has been an integral part of the underground mining industry in Australia. Ever since Busby's Bore was developed using black powder to supply Sydney with water, miners have been drilling holes, filling them with explosives and blasting the rock into a manageable size. The drilling was fairly straight forward but the explosives were always a mysterious commodity. It worked, but how and why? The explosives industry is now working much closer to the mining industry to dispel these mysteries and also to aid the advancement of explosive technology. This paper looks at the results of these advances in the form of explosives, accessories and blasting systems.

Jan 1, 1992

By H W. Wu, T Harvey

An overview is given of two new developments in mine atmospheric monitoring. A new personal dust monitor (PDM) that gives real-time respirable dust readings is discussed. The unit is mounted within the minerÆs cap lamp battery and internally measures the true particle mass of dust collected on its filter. Samples are available for later mineralogical analysis and results do not exhibit the same sensitivity to water spray as optically-based measurement approaches. The technique achieves microgram-level mass resolution even in the hostile mine environment and reports dust loading data on a continuous basis. The monitor has been evaluated under an Australian Coal Association Research Program (ACARP) grant and is being adopted for statutory mine respirable dust determinations in the United States (US). The monitor has particular application for determining location of high dust sources. It can evaluate the efficiency of engineering means of suppression and other approaches to reducing dust levels. It has been recognised that the PDMÆs unique measurement approach has application to allow real-time atmospheric diesel particulate matter (DPM) monitoring. The industry has no real-time atmospheric DPM monitor at present. Recent surveys in New South Wales and Queensland show significant numbers of miners continue to face full shift DPM exposures in excess of internationally accepted levels. Real-time DPM monitoring will allow the industry to pinpoint high exposure zones where a number of trucks and other vehicles work in areas of poor ventilation. Knowledge of high DPM concentration zones allows efficient modification of work practices to reduce underground minersÆ exposure. Approaches to uses of the DPM form of the monitor and the design of tag boards are discussed. Some outcomes from mine tests with both these new instruments are given.

Jan 1, 2008

By J Rutter, D La Rosa, P Walters, M Scott, L Keeney

Bulk ore sorting technologies, whether surfaced based or penetrative, have seen an increased uptake by the mining industry for preconcentration application. As with all technologies, going through the technology validation process is key to de-risking the operationalisation of the technologies and to demonstrate and confirm predicted value propositions. The ability to laboratory calibrate cross-belt bulk sensors is standard practise for sensor vendors, however transitioning the technology from laboratory to real-world application is a non-trivial process. The industry has taken two main approaches to trialling and validating bulk sensing technologies in operational environments, namely:  Construct an off-line pilot facility at scale, or  Install bulk sensing systems on production conveyors Each of these two approaches have significant advantages and disadvantages and require different experimental design programs and analysis methodologies. Consideration of material movement, heterogeneity degradation, logistical requirements, and financial investment all factor into which approach is most suitable for an evaluation scenario. CRC ORE in partnership with mining companies, have conducted several bulk sensor pilot trials utilising different sensor technologies employing each of the two main approaches outlined above. This paper describes the challenges faced, learnings obtained and outlines a position on how to transition bulk sensing technologies from the laboratory into the operating environment. The case studies presented cover a range of commodity types in both open pit and underground operations.

Nov 10, 2020

By S Rogers, D Stead, E Eberhardt

The last decade has seen a major increase in use of the discrete fracture network (DFN) approach applied to cave mining problems, often integrated within more complex geomechanical simulations. Because the value of the DFN model directly depends on the quality and quantity of available field data, there is the need to apply dedicated mapping procedures to collect sufficient structural data at the required engineering scale. This paper attempts to address several key questions about DFN modelling; for example: are current methods for fracture mapping suitable for DFN modelling? What are the critical parameters that we need to measure and what do we need to change in the current practice? Particularly at the earlier stages of a cave project, engineers may have to account for the lack of appropriate data, which manifests itself in the form of increased uncertainty and the difficulty to characterise variability in an objective manner using a limited set of data. DFN models could in principle be generated using limited data by assuming statistical distributions for the sampled parameters; however, engineers would need to be aware of the implications that such limited knowledge (and increased uncertainty) would have on stability analysis, fragmentation analysis and mine design. When used correctly, a DFN approach offers practitioners the opportunity to:maximise the use of fracture data collected from mapping of rock exposuresgenerate more realistic synthetic rock mass modelsprovide estimates of natural fragmentation that also account for rock mass variability.CITATION:Elmo, D, Eberhardt, E, Stead, D and Rogers, S, 2016. Discrete fracture network modelling – importance of accounting for data uncertainty and variability, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 845–852 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By S A. McManus

With the advances in software speed and capability, many of us now are running multiple scenarios on entire models rather than just testing small areas or a few blocks. In the authors experience both the geological and geostatistical academic theory and our rules of thumb, often prove un-useable or incorrect in the real world we work in. The only way to truly validate and tune our models is to complete the entire model and ‘see if it works’. If it lacks some property we were expecting, then we need to find out why and/or run different scenarios to see what changes. This is not always possible with tight project timelines but we find ourselves doing more and more of this sort of thing, and in so doing, understand that every deposit is different and requires its own ‘rules’ to get valid and useful results. For the purposes of this paper, this process is termed Empirical Geostatistics. Take Clayton Deutsch’s ‘all realisations all of the time’ concept a step back. Before you even think of simulating, test the alternate realisations generated by alternate parameters such as different domaining, varying search neighbourhood parameters etc.

Mar 22, 2022

By C Berglin

Is the Northern Territory different? Certainly it is more remote, has less people and relies more heavily on two or three industries for its survival. On the other hand, its mining industry is governed by Acts not dissimilar to those of the major States - a Mining Act provides the basis for acquisition of tenure, a Mine Management Act provides regulatory control, a Mineral Royally Act collects revenue in return for the right to utilise the land's bounties, an Environmental Assessment Act provides the public face to rehabilitation and environmental safety, and the Aboriginal Land Rights (NT) Act purports to give development criteria for inalienable land use. With the exception of the latter, at least until the advent of Mabo, all these are simply variations on a theme, and are common to most States. This paper will show how the Department of Mines and Energy works in relation to the Northern Territory mining industry.

Jan 1, 1994

By C Armstrong, B Wentzinger

Upstream embankment raises often represent the lowest cost option for increasing the capacity of tailings storage facilities (TSF), but also pose the highest stability risk due to constructing on top of previously deposited tailings.This paper presents an overview of key aspects in the geotechnical investigation and design of upstream raises and some recent lessons learnt from experience across a number of TSFs in Australia. A summary of recommended field investigation and laboratory testing methods is provided with a focus on collecting quality information for design purposes. A strong focus is given in developing an accurate assessment of pore water pressures, which, if not correctly understood can have disastrous consequences on tailings strength parameter interpretation and wall stability assessment in static and post-seismic conditions.The assessment of the contractive or dilative shearing behaviour of the tailings material and rigorous interpretation of design characteristic values are presented. Some comments on stability analysis options and proposed methodology are also provided.CITATION:Wentzinger, B and Armstrong, C, 2018. Lessons learnt in geotechnical investigation and stability analysis for upstream tailings storage facility raise design, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 333–348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By P Valenzuela

Joint mapping is a fundamental input for rock mass characterisation and slope stability analysis. The usual way to do it is using a compass in the field or digitising structures on a screen, with a software package.In this paper a method to identify and map joints automatically along a rock face is presented; it is called the Concentric Shells (CS) algorithm. The method scans a point cloud sequentially, tests if selected points are ‘true pivots’ within an inner shell, and then it searches for points inside a wider sphere (outer shell).The algorithm, developed by the author, was applied in real data. It reproduces the main features obtained from conventional (compass) and digital mapping (software package). Execution times are approximately 45 seconds for two point sets holding of 3.1 million points. Obtaining the same results via digital mapping takes approximately 3–4 working days.Key advantages of this method are: significant time reductions; elimination of mapping bias; and the ability to manage very large data sets (>2 million points) without the need of scanning the cloud on the screen. These advantages make this method an attractive tool for engineers and geologists wanting to increase productivity.CITATION:Valenzuela, P, 2017. Automated joint mapping using the concentric shells algorithm, in Proceedings Tenth International Mining Geology Conference 2017, pp 257–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

With the theme of û æUnderground Ore Handling SystemÆ, Kopanang Mine completed an extensive project on a specific system with technologies for the handling of ore from a dedicated drawpoint to the shaft system. The intended rail haulage tramming system had to be capable of handling the shaft design and Life of Mine (LOM) requirements. Kopanang is an AngloGold Ashanti gold mine situated in the province of the Free State in South Africa. In the Sotho language the name æKopanangÆ means to come together as a team. ItÆs an appropriate name given that 25 companies worked on this project. The future focus at Kopanang is to establish four mining levels between 3 to 4 km south-west of the shaft and two mining levels to the west. The mine has an expected life of almost 20 years and capital was approved in order to access this reserve to establish the infrastructure to handle the ore, hence this exclusive rail haulage tramming system of close to R40 million (SA rands), which took three years to construct. Apart from the fact that this system had to be capable of handling 6500 t per shift at a depth of over 2 km over a length of 3.2 km, some of the major considering factors were: safety, economic factors with improved labour productivity, efficiency and reliability, risk termination, and ergonomics. The system comprises two 20 t locomotives operating in a double header configuration from a dedicated draw point to a dedicated tip area for the reef and waste ore. With the objective of handling high speed and high capacity, this 200 t payload train is capable of running at 35 km/h powered from a 500 volt ac overhead line. Each loco consists of two 90 kW dc motors with ac/dc power conversion on the locomotive. For the system to operate at this speed, the rail system is constructed with Class 1 rails over the entire hauling distance. The tipping mechanism is unique and the span of 11 hoppers each with a load of close to 20 t is capable of tipping the pay load of 200 t in about 20 seconds hands free.

Jan 1, 2005

By Sataev IS, Malinovskaja ND, Otrozdenova LA, Knodov NV, Maximov II, Kuznetzou OK

The technology of flotation recovery of silver from the residue of a zinc plant is described. The peculiarity of this technology is a preliminary pulp conditioning in sodium chloride solution in the presence of aluminum metal under high temperature. In this process the silver is converted to the metallic phase and then floated with the usual sulphydryl collectors. A variant using a combined technology is also described, in which before flotation is performed about 50 per cent of silver is leached. The total silver recovery with the combined technology comes up to 90 - 94 per cent.

Jan 1, 1993

By W. M. LONIE

Address by the President of the Institute (Mr W M Lonie) in making the presentation of the Certificate of Honorary Membership to Sir Ian McLellan, K.C.G.M, K.B.E. Address by Sir Ian McLellan after accepting the award.

Jan 1, 1979

By B Murphy, S O’Connell, J L. Heath

In the 1989 best-seller The 7 Habits of Highly Effective People, the author, Stephen Covey, highlights the importance of maintaining not only ‘production’, but also, ‘production capacity’. When operating a modern flotation concentrator, production is often measured in terms of concentrate tonnage, tonnes milled and plant utilisation. There are very few metrics that focus directly on flotation equipment condition in relation to performance, which is analogous to Covey’s production capacity principal. It is evident on many mine sites that flotation equipment condition is not monitored on a proactive basis and that the prevailing culture is to wait for a failure, before addressing an issue.This paper discusses examples of how poor equipment condition can lead to production loss through poor metallurgical performance. Actual examples are given where these problems have occurred in operating plants. An outline is provided on how metallurgical and maintenance departments can work together to protect production capacity and gain more from existing equipment.CITATION:Murphy, B, O’Connell, S and Heath, J L, 2014. Maximising value through maintaining your flotation equipment, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 71–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By A Horne, Z Graszkiewicz, D Dettrick, R Evan, B Neal

"Most of VictoriaÆs rivers and aquifers are already fully allocated or reaching full allocation. In regions without a well-established water market, access to water entitlements to facilitate new development is limited. In areas with established water markets, mine developers face an undue cost burden in circumstances where they are only planning to consume a fraction of the water entitlements that they purchase. The challenge for water managers is to ensure protection of water resources and other water users without creating an unnecessary disincentive for those types of developments that return most of the water that they take from water sources. The opportunity for development of a mine is explicitly linked to a particular location and must be developed where a resource is located or it cannot be exploited at all. Regulatory arrangements that facilitate development may have a positive impact on economic development, particularly where water availability is a potentially limiting factor. Net volume licensing has the potential to allow increased economic outcomes through improved licensing of access to water. Net volume licensing differs from traditional water licensing in that it authorises access to water on the basis of ænet useÆ rather than æthe gross volume takenÆ. This paper asks under what conditions net volume licensing is likely to be feasible and effective. In particular, the paper examines the information and accuracy requirements to allow net volume licensing decisions to be made. This work is based around five case studies in Victoria that were used to examine the potential for net volume licensing for mines and quarries. Assessing a potential net volume licensing arrangement requires the regulating authority to have an understanding of the inputs and outputs of water to a site. In contrast, assessment of take and use licences consider only a single input. It was concluded that the conditions that lend themselves to net volume licensing include: well understood water inputs and outputs, including appropriate accuracy of information where the location of site water inputs and outputs are the same where the timing of extraction and discharge can be managed to minimise impact on the water resource.A key remaining challenge is establishing an accounting framework that allows net volume licensing under current water resource limits. CITATION:Graszkiewicz, Z, Horne, A, Neal, B, Evan, R and Dettrick, D, 2013. The practicalities of implementing net volume licensing of water use in mines and quarries - a discussion based on Victorian case studies, in Proceedings Water in Mining 2013, pp 241-250 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By J M. Galvin

History attests to the catastrophic consequences that fire, explosion and contaminated, noxious andirrespirable atmospheres can have for workplace health and safety in underground coal mining. It also confirms that fires and explosions present the greatest risk of partial or total loss of underground mines and equipment and that this risk continues to materialise. The design, implementation, operation and maintenance of the mine ventilation system are core controls for managing the hazards associated with these risks, both for preventing them from materialising and for mitigating their consequences if they do materialise. These are most effective when embedded in a risk management approach.

Oct 12, 2022