Search Documents

By Z Li, Z Yan, M Yang

Recycled cement paste (RCP) is a kind of CaO-rich recourse, which is separated and recycled from waste concrete. Due to its chemical composition, RCP could partially replace lime as a flux and be loaded into electric arc furnace (EAF) steelmaking process. Rapid RCP assimilation and liquid slag formation have significant effects on EAF steelmaking process. In this study, the dissolution behaviours of RCP and lime at temperatures of 1400°C to 1500°C were investigated using static dissolution experiment. The dissolution rate, interfacial microstructure, as well as dissolution mechanisms were discussed. It was found that the dissolution rate of RCP was much higher than that of lime. RCP could be completely dissolved into slag in 60 secs at 1500°C. The dissolution rate of lime was in range of 3.910-4 g/(cm2ꞏs) to 2.610-3 g/(cm2ꞏs), while that for RCP was in range of 1.510-3 g/(cm2ꞏs) to 4.910-3 g/(cm2ꞏs). As for lime dissolution, a dense layer of dicalcium silicate (C2S) generated at the dissolution interface, and the diffusion of Ca2+ in C2S layer was the limited step for lime dissolution. Some of calcium ferrite could be observed at the interface between lime and C2S layer. As for the RCP dissolution, there is no obvious product layer of C2S formed at the dissolution interface, Fe2+ continuously diffused into RCP layer during the dissolution, and small amount of FeOꞏMgO solid solution generated and gathered at the dissolution interface. The dissolution rate of RCP in EAF slag was quite higher than that of lime, partially add RCP as flux in EAF could accelerate the slag formation process.

Aug 21, 2024

By Caelli T, Robey M

Most research into planning of open pit mines has been based on evaluation of volume-element block models in terms of their net present value. The major issues revolve around two interdependent problems the optimum ultimate pit and time-based scheduling. Despite feedback between the two problems, they are usually treated as separate tasks.The ultimate open pit is defined by the removal of whole blocks so that their net present value is maximised. This gives planners an estimate of the total worth of the venture in present terms, and is crucial to obtaining funding. All cost and profit values are assumed to be static throughout the mine life, and the only physical constraint usually taken into account is that of safe, average, wall slopes, which must be approximated by the removal of whole blocks. Modelling of any further constraints (for example, access roads and true wall slopes) is usually achieved by adding them to the optimal pit by hand. Typically this degrades the model by between five and 20 per cent of its value - which then brings into question whether it is still the true optimum.This paper reviews the dominant methods in use for this first task the ultimate open-pit planning problem. Some new optimisations are given, and the algorithms are examined in terms of their efficiency and accuracy. Finally, suggestions are made for improvement of model accuracy and eventual expansion into solutions of the more complete dual problem - that of simultaneously finding the optimum ultimate pits and dynamic schedules for the venture.

Jan 1, 1996

By Jackson S

An investigation into different aspects of importance in the understanding of explosibility of hybrid mixtures of coal dust, air and gases potentially found within mine workings through a comprehensive laboratory program of explosibility tests was conducted. Plotting of test results revealed that conditions of potential explosibility could be described using two dimensional flammability limit surfaces- for coal dust/oxygen; methane/oxygen; and coal dust/methane mixtures. From these plots, the three dimensional flammability envelopes defining the explosibility of the coal dust/methane/oxygen mixtures can be defined and illustrated for a coal sample. The surfaces of the three dimensional envelope describe limits which separate inert mixtures of coal dust and methane at varying oxygen levels from those concentrations which are ignitable under defined conditions. It is considered appropriate to generalise that the geometric shapes of these limit regions are applicable to all type classifications of coal dust. There are practical applications of these results to the underground environment.The action of free radical initiators in the propagation of a methane gas explosion was examined for its applicability to the flammability of coal dust/gas/air mixtures. The oxides of nitrogen or NO x radicals have influence upon the lean limits of flammability of hybrid mixtures and this is illustrated by use of three dimensional coordinate geometry. Gases can be introduced to the underground environment through the exhaust gases of diesel equipment. It is concluded that radical species can substantially increase the flammability of gas and dust flames and as a consequence raise risk of mine atmosphere explosibility.

Jan 1, 1998

By D Craw, G Eis

Late Cretaceous Blue Spur Conglomerate preserved as isolated remnants at Gabriels Gully, Weatherstones, Forsyth, Waitahuna Gully and Adams Flat was deposited during the intiation and early stages of extensional movement on the Tuapeka Fault zone at each locality. The deposits represent successive courses of a single fluvial system flowing across the Tuapeka Fault zone from the up-thrown (northeast) block. Each course, beginning with the channel at Gabriels Gully, was abandoned as a result of uplift-induced defeated antecedence in favour of a new course farther to the southeast around the southeast-propagating tip of the Tuapeka Fault zone. Schist and quartz in the conglomerate was derived ultimately from schistose rocks northeast of the Tuapeka Fault zone. Caples Terrane greywacke detritus in the middle and upper beds of the conglomerate was probably recycled from pre-existing sedimentary cover on the up-thrown block, following initiation of uplift on the Tuapeka Fault zone at each locality. Most of the gold is derived from vein sources in Otago Schist rocks to the north, and/or associated placers. Hydrothermal veins at Waipori, Hindon, Barewood, and Macraes are the most likely primary sources. There is no evidence to support previous interpretations of deposition by river systems flowing from the southwest, or axially along the Tuapeka Fault zone from northwest to southeast. High gold grades within Blue Spur Conglomerate should have a linear trend more or less similar to the orientation of the host channels, but are likely to drop off rapidly to the southwest. Extensions of the conglomerate-filled channels are unlikely to be preserved, but there is a strong probability that younger placers recycled from the former channels exist.

Jan 1, 1999

By C Glassock, P Bodon, M Elias

Computer simulation is a well-accepted tool for modelling the behaviour of large or complex operating systems. Less common is the use of simulation as a design aid, but FluorÆs simulation group regularly applies discrete and continuous simulation models to assist with optimisation and risk management in a wide variety of mining, mineral processing and logistics applications. To demonstrate the wide applicability of simulation modelling as a design aid, this paper describes three case examples from FluorÆs recent work that cover both discrete and continuous operations.

Jan 1, 2003

The ore body being worked is about one hundred feet in length by seventy feet in width. A face of about fifteen feet is stoped over the whole level at one operation, this height standing without any timber.Double lines of logs, twenty feet in length and from ten inches to one foot in thickness at the small end, are then laid longitudinally, butt to butt, and breaking joint from end to end of the ore body they are at ten feet centres from wall to wall. The starting logs are single for the first ten feet and their ends are hitched into the solid rock. These are called "miners" and are the logs which are picked up as the level underneath is worked up. The double layer gives a better chance of picking up. Logs are now laid from the centre of the ore body at right angles to the miners, the ends being hitched into the walls. A space, seven feet wide, is left open right through the centre of the ore body...

Jan 1, 1904

The Iron Prince orebody occurs within the Lower Middleback Jaspilite Horizon of the Middleback Group and consists of hematite within host rocks of jaspilites and schists. The ore was probably the product of leaching of silica from jaspilites and replacement by iron, concentrations occurring in suitable structural traps. The narrowness and the presence of extensive dolerite amphibolite dykes within the orebody make it essential to operate a grade control programme in advance of the faces. Information from drilling is drawn up on bench plans, step plans and impurity overlays, and these serve both in day to day production planning and in long term planning. Mining is done selectively by open-pit methods and blending conducted by keeping at least three faces of different grades of ore open at any one time. No stock piles of ore are kept for blending, but contact ore, contaminated ore and enriched material are dumped for later beneficiation.

Jan 1, 1971

By J Austin, R Bitencourt

Differences between the long-term model (LTM) and mine geology system (MGS) grade control block-outs on a blast block scale can impose difficulties to planning crusher feed grade and tonnes on a monthly to weekly blend basis. Detailed geological input to short-term planning has been integral to improve the performance and reduce risk in six-week to three-month production schedules and local variability in tonnage and grades is often not accurately represented in the LTM. The challenge of producing to combined target specifications from different mine sites in an integrated mine to ship business has been reduced with the creation of blast blockout-based short-term model. These short-term blast block models (STBBM or STM) are robust predictive tools created for upcoming benches of current mining areas by firstly collecting data from the pit in the form of bench and face mapping and projecting the structure and stratigraphy down to the next bench. A wire-frame of the projected contacts based on material destination from production blockouts is created and then checked against the LTM. Blast block data from the bench above including assay results and material logging is extracted and validated according to the projected wire-frames (geozones). Individual blast blocks and a full block model are created for each bench production defined by the STP (bench plans). Data output from the STM is in a compatible format for import into scheduling specific software packages. Additional information is incorporated into the STM to allow querying of drill penetration rates, predicted powder factors, material hardness and feed type to further aid in the production planning process and cost forecasting. To date, reconciliation of the STM has been pleasing and certainly an improvement on the LTM, especially in areas where variability is higher due to geological complexity. Short-term predictions derived from in-pit geological observations allow mine planners to more confidently decide on mining block sizes and schedule tonnages and grades, reducing the risk component attached to developing production schedules based directly upon long-term orebody models and mine plans.

Jan 1, 2005

By H Aral

A rotating magnetic field can be produced in a magnetic separator by using a magnet rotor fitted with alternate north-south magnetic poles, similar to the rotors currently used in modern eddy current separators. Rotation of the magnetic field causes ferromagnetic particles to rotate during magnetic separation. The particle rotation can then be used simply to remove entrapment during a conventional attraction magnetic separation (RMF lift separation), or it can be used to roll particles away from non-rotating particles, and to move them out of the separator under their own rotation (RMF rotation separation). RMF (rotating magnetic field) separation is a separation for ferromagnetic particles. These particles have a very ordered magnetism that is locked into directions of easy magnetisation in the crystal. As a result, if the external field rotates, the particles attempt to rotate with it. RMF separation uses this fact to rotate the ferromagnetic particles in a rotating field. In contrast, paramagnetic particles have a magnetism that can point in any direction with almost equal ease, and these will not rotate in a rotating field. By making use of this difference in magnetic properties, RMF rotation separation can separate ferromagnetic particles from paramagnetic, even when the particles have similar susceptibilities. Some particles such as both chrome spinel and ilmenite can contain ferromagnetic regions within a paramagnetic matrix. These ferromagnetic regions can vary from very small regions dispersed throughout the crystal, through thin lamellae, to larger more bulky regions. Although most natural ilmenite is ferromagnetic and generally has a higher magnetic susceptibility than paramagnetic chrome spinel, the susceptibility ranges for the two minerals overlap considerably (Allen, 2000a) due to the presence of these ferromagnetic elements, frequently making the conventional magnetic separation of these two minerals impractical. It is known that roasting a mixture of ilmenite and chrome spinel particles increases the magnetic susceptibility of the ilmenite while leaving the spinel susceptibility substantially unchanged. This makes the use of conventional (susceptibility attraction) magnetic separation more practical for the separation of these two minerals. However, very little is known about the effects of roasting on the response of ilmenite and spinel particles to a rotating magnetic field. For example, although the optimal ilmenite roasting conditions for conventional magnetic separation are quite well established such conditions may or may not be optimal for RMF rotation separation. Low intensity conventional magnetic separation on the basis of magnetic susceptibility can be made more accurate if it is carried out in a rotating field, because the rapid spinning of the separating particles prevents the formation of magnetic flocs, and reduces entrapment and entrainment. Medium intensity RMF rotation-only separation (no attraction component) has the ability to separate rotating (ferromagnetic) from non-rotating (paramagnetic) particles, irrespective of their relative magnetic susceptibilities. RMF rotation separation is of particular interest in this case because ilmenite particles generally rotate much better than the mainly paramagnetic chrome spinel particles, and roasting could enhance this difference further. Further information on the use of RMF to separate minerals can be found in Allen (2000a; b and c). The aim of this series of tests on a number of Australian ilmenites was to compare some different oxidising and reducing roast methods and to establish whether the use of RMF rotation separation improves the chrome spinel rejection.

Jan 1, 2001

By M E. Trim, J J. Johnson, W Cranston

The Brightwater conveyance system is located near Seattle, Washington in the north-western United States. The East Contract portion of the system consists of a 4.3 km long, 5.9 m diameter tunnel in soft ground and two large shafts constructed in challenging soil conditions. The two shafts are situated side-by-side in an urban valley. One will house an influent structure to direct incoming sewage and outgoing treated effluent, while the other will house a 645 megalitre per day (ML/d) influent pump station. The tunnel contains four pipelines: two force mains to convey untreated wastewater eastward from the new pump station to a new treatment plant, one gravity-pressure pipeline to convey treated effluent westward to a new outfall in Puget Sound, and one high-pressure pipeline to convey reclaimed water from the treatment plant to downstream distribution points. The shafts and the tunnel presented many design challenges. Groundwater is near the surface in the area surrounding the shafts, and compressible peat and clay soils preclude dewatering during construction. These and other challenges were encountered during design of the pump station shaft and multiple-pipe tunnel. The challenges were addressed by a design that includes a dual intersecting circular cell shaft (referred to as æthe peanutÆ) and a single tunnel into which stacked pipes will be æstuffedÆ. This paper discusses the design approach and design details for both elements.

Jan 1, 2008

This paper summarizes the progress of geological exploration at North Broken Hill Ltd.The North Mine orebodies occur in knots of minor folds on a simple limb structure which is itself highly folded, giving rise to two distinct orebodies pitching N. at av. 42° down to 2,920-ft. level, where the pitch steepens to near vertical as a result of complementary shear movement on the Globe-Vauxhall Crush Zone.The lack of adequate marker beds and top and bottom relations makes the resolving of the complex structural environment of the orebodies most difficult.To test the deeper ground of each side of the De Bavay Fault on the 2,600-ft. level the footwall drive was extended 3,556 feet and over 20,000 ft. of drilling completed from three transverse fans, only one of which intersected the orebodies due to steepening of pitch.The problem of locating the North Mine orebodies N. of the DeBavay Fault remains speculative because the exact position of them S. of the fault is still unknown. Exploration beyond the fault in the search for ore had two lines of mineralization to consider, an eastern one through Cosgroves-Round Hill, long regarded as the continuation of the main lode, and a western one passing through Silver Hill Silver Peak.From surface 45,000 ft. of drilling was completed in five sections, establishing that the structure was dominantly synclinal with a flatdipping E. limb, the W. limb and adjoining structures being involved in the Globe-Vauxhall Crush Zone. Mineralization, though weak, was remarkably persistent but the economic mineralization exposed at surface has not persisted with any continuity.Deep exploratory drilling below the bottom level (3,370 ft.) has established high-grade ore to a depth of 4,095 ft. and also has proved its existence within the Globe-Vauxhall Crush Zone.INTRODUCTIONThis paper summarizes the progress of geological exploration at North Broken Hill Limited from the inception of the Geological Department in 1941 until the end of 1955. The writer has drawn freely on departmental records for the period prior to 1947.

Jan 1, 1956

Whilst employed by Dyno Nobel as the Technical Services Engineer û Brisbane, I was asked, as part of a contractual agreement, to look at optimising PioneerÆs blasting process to provide the most effective rock to the new crushing and screening plant. This paper details the preliminary blast designs and practices that have been in use at the quarry and the initial changes made to these designs, and the effect they have had on the excavation and crusher performance.

Jan 1, 1999

By Snowden D. V, Standing C. A, Ryba A, Bywater A

McKinnons open pit gold mine, located within the Cobar Basin in New South Wales, is characterised by complex mineralisation controlled by the intersection of steep faults in the hinge zone of an anticline. Resource estimation using indicator variography and indicator kriging was based on RC drilling on 25 in sections together with grade control RC drilling on 12 in by 12 in and 6 m by 6 in patterns. Rigorous sampling and checking procedures were used to verify the reliability of the drill hole data. Blast hole data was used to assist grade control in defining ore block boundaries.

Jan 1, 1997

By M, C A. RosiFre, R C. Figueiredo e Silva

Jaspilites and underlying basalt contacts of the Archaean volcano- sedimentary Grpo Parß Group, Carajßs, host giant iron mineralisation in the ~100-km long, E-W trending Carajßs fold. Preliminary, unpublished geochronological data point to a Palaeoproterozoic mineralisation event. Geochemically, jaspilites are typical volcanogenic banded iron formations. Basalts exhibit evidence of spilitic seawater interaction. Iron-associated hydrothermal alteration of mafic rocks was induced by fluid infiltration in amygdales, with development of chlorite- and hematite-dominated zones. In the case of jaspilites, iron mineralisation encompasses: partial replacement of jaspilitic microcrystalline hematite by blasts of martitic magnetite; jasper recrystallisation, producing fine-grained, hematite-free granoblastic quartz; martite recrystallisation, forming lobate¦subhedral hematite; pervasive porosity development by quartz-chert leaching; incipient cavity filling by microlamellar hematite; and advanced filling by coarser, euhedral and comb-textured, tabular- shaped hematite.Peak hydrothermal ore textures indicate typical epithermal-crust conditions, supported by preliminary fluid-inclusion calculations at 160 - 200¦C. Such temperatures and extreme fluid-to-rock ratios during alteration must have exceeded the ambient metamorphic conditions, with the infiltrating fluid relatively hot and capable of leaching SiO2. Therefore, mineralisation developed over exhumed, Archaean, brittly deformed rocks, with mineral associations representative of very low- to low-grade metamorphism. Considering that chlorite (¦talc) abounds in mafic rocks; hydrothermal albite is developed; dolomite fills veins and vugs; the typical rare-earth-element (REE) pattern of jaspilites is significantly modified in higher-grade hard hematite ores (higher LREE); pyrite, copper sulfide minerals and rare gold occur in association with carbonate-quartz-rich alteration zones, it is suggested that an alkaline, H2O-Fe-CO2 mineralising fluid dominated, also containing species like S¦Cu¦Au. Peak-mineralising conditions are likely to have resulted from a single, evolving fluid, via incipient- through advanced-stage alteration phases. The porous, high-grade soft hematite-type ore (SH), rich in microlamellar and anhedral hematite, must have derived from interaction with this relatively hot SiO2-leaching fluid, whereas the high-grade massive hard hematite-type ore (MH) developed due to closer fluid-rock temperature equilibrium conditions, attained by mineral reactions, with relative increase in the Fe/Σcations ratios allowing the precipitation of subhedral-tabular hematite that partially cements the soft-hematite ore. SH and MH hematite ore types must thus reflect intermediate and high fluid:rock ratios, respectively. Since the N5 deposit is to date understood to contain the largest amount of the MH ore, its units are interpreted as the loci of the highest fluid:rock ratios in the district. Preliminary mineralogical information regarding the S11 deposit of the Serra Sul (south range) implies higher-temperature conditions. The near-equant grain size and the granoblastic intergrain relationship, coupled with the presence of riebeckite, augitic pyroxene and garnet, suggest hornfels textures. The data collected, though still relatively sparse, permit the speculation that the immense driving force for the Carajßs world-class iron deposits was a relatively shallow, igneous-related hydrothermal system. If such a model is correct, then the Carajßs Palaeoproterozoic iron deposits could represent an end-member of the iron oxide-copper-gold hydrothermal system in the province.

Jan 1, 2005

A review is given of progress made to- wards the development of personal gravimetric dust sampling for risk assessment on South African gold mines. The present strategy is critically examined on the basis of principles for assessing health hazard from dust exposure. Reasons are advanced for replacing the konimeter with a gravimetric system based on full shift personal sampling. Constraints imposed by local characteristics of gold mines are used to illustrate the difficulty in finding suitable instrumentation for measuring personal exposure to respirable silica.

Jan 1, 1988

By M J. Kelleher

CREAM is an acronym for coal recovery, evaluation, analysis and management and is a business improvement project at BMAÆs Goonyella Riverside mine that is focussed on maximising coal recovered. In August 2003, Goonyella Riverside was set a challenge to quantify coal loss and dilution and their relationship to cost, revenue and ultimately profit. While the mine was confident in its site forecasts of recovery (and loss), it was clear that the traditional measurement and analysis systems were inadequate to firstly, identify key loss areas and mechanisms and secondly, successfully quantify the benefit of various coal recovery initiatives. The path that BMA Goonyella Riverside has travelled to maximise coal recovered can be divided into four key steps: Mapping the process û This step involved the development of a coal flow process map for Goonyella Riverside that stepped through each component of the process from the coal reserve to the customer and identified key measurement points for the purposes of reconciliation. Understanding coal loss and identifying opportunities û This step involved conducting two detailed Reserve to Customer projects at the mine site to track a block of coal from the reserve to the customer and to gain a greater understanding of the relationship of dilution, coal loss mechanisms, revenue and costs associated with recovering additional coal. Coal data systems development û Two important coal data systems have been developed and implemented at Goonyella Riverside in the past twelve months, namely SnowdenÆs Coal Reconcilor and SeamFix. These systems enable coal losses and dilution to be quantified and reconciled back to the initial coal reserve. Implementation of loss reduction initiatives û This step involved the formation of a business improvement project referred to as æCREAMÆ in August 2004, for the purposes of improving pit coal recovery and maximising business value. To date a series of coal recovery trials have been run in a number of pits at Goonyella Riverside that have yielded significant improvements in business value. The key to the success of this project has been the discipline to follow a defined process map, management commitment through resourcing and shared key performance indicators, a successful acceptance strategy resulting in holistic ownership and the implementation of sustainable reconciliation systems. Coal loss and dilution are now quantifiable and their relationship to cost, revenue and ultimately profit is well understood. This paper discusses the process that Goonyella Riverside has adopted to maximise coal recovered.

Jan 1, 2005

By Rienks, Wyborn D

The Ravenswood Batholith in the Charters Towers -Ravenswood area of north Queensland, was formed by three main episodes of granitoid emplacement between the Early Ordovician and the Early Permian. Granite to granodiorite plutons of the first phase of intrusions in the Early to Middle Ordovician, probably formed by partial melting of a thin continental crust as a result of the emplacement of mafic material derived from the mantle. Some of this mafic material subsequently intruded the Ordovician granitoids as gabbro to diorite complexes. The early granitoids were deformed and metamorphosed prior to emplacement of second phase granodiorite to tonalite plutons in the Late Silurian to Early Devonian. These later plutons have generally not been deformed or recrystallised. Geochemical and isotopic data suggest the Siluro-Devonian plutonism may have been generated by a partial melting of the tholeiitic material emplaced in the lower crust during the Ordovician. A third intrusive phase consists principally off Late Carboniferous to Early Permian gabbro-granite complexes, high level granite to granodiorite complexes, and rhyolitic plugs and diatremes near the batholith margin. Gold mineralisation in the batholith is associated with two major events: mesothermal vein formation in the Early Devonian and porphyry types in the Late Carboniferous to Early Permian.

Jan 1, 1990

By Tyler DB, Thin LGT

Coal mass strength properties must be estimated to obtain realistic estimates of coal pillar strength. The limitations of existing techniques for approximating these properties are discussed. The coal mass is anisotropic. The Hoek and Brown approach to rock mass property estimation is modified to allow for this. This approach requires the Rock Mass Rating (RMR) for the strata. In the normal case where bedding is sub-horizontal, these major planes of weakness have little effect on the strength of pillars. As a result of this the RMR must be measured parallel to bedding. This means that a significantly higher rating than that usually obtained for coal is observed. The use of mass strength property estimates in extant empirical relationships is outlined. At high width to height ratios, an acceleration in the rate of increase in pillar strength with increasing width to height ratio has been observed. The empirical relationship developed by Salamon (the so called squat pillar formula) takes account of this. This relationship was found to have significant limitations with respect to its universal application. Modifications are made to Bieniawski's empirical formula to extend its use to large width to height ratio (squat) pillars. This new squat pillar formula has none of the disadvantages associated with Salamon's relationship. Strain softening was incorporated into non-linear finite difference numerical modelling to estimate pillar strengths. The technique outlined above is used to obtain peak coal mass properties. Modelled pillar strength was found to be sensitive to both peak and post peak mass strength properties. Post peak properties were found to be difficult to obtain and required some back analysis. Modelling results were used to estimate both the strength of squat pillars and parameters for use in a new squat pillar empirical strength relationship.

Jan 1, 1992

By T G. Measham, D A. Fleming

When attempting to understand potential regional or community socio-economic changes that resource-extraction industries may produce, it is important to analyse the channels that promote these changes. In this study, we propose a conceptual framework to better understand how socio-economic effects are likely to emerge in regions impacted by mining. The framework considers three levels of hierarchical effects (Measham, Fleming and Schandl, 2016).In the first level, the resource-extraction industry causes four direct initial impacts on nearby communities: labour demand shock (mining employment generation), income generation (compensation to landowners and higher wages), environmental consequences and land tenure/Aboriginal issues and an increase in local tax revenues.The second level is shaped by the subsequent population increase (given by immigration of permanent or temporary residents) produced by the new levels of employment and income that resource windfalls can generate in resource-extraction regions. These increases in employment, income and population become the source for a rise in the demand for local (and non-local) goods and services.Finally, the third level is given by boomtown-like and other socio-economic effects generated from the initial effects.CITATION:Measham, T G and Fleming, D A, 2016. A conceptual framework to understand the local community/social impacts of mining, in Proceedings Life-of-Mine 2016 Conference , pp 188–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

As this paper is being written primarily for perusal by milling workers, metallurgists and engineers, an attempt will be made to avoid the use of accounting technicalities. Its scope will be confined to a description of the methods employed in the collection of basic information for use in timekeeping, costing, and the compilation of statistics.TIMEKEEPINGEvery applicant for work is asked to furnish the following information, which is collected on a card (size 6 in. x 4 in.)...

Jan 1, 1922