Search Documents

By Heath E, van Calsteren P, Turner S, McDermott F

U-Th isotope studies of recent volcanic rocks may be used to evaluate the depths and rates of melt generation beneath mid- ocean ridges and ocean islands. Island arc rocks exhibit a similar range in Th isotopes to that seen in both MORB and OIB, but while those with high (230Th/232Th) tend to have excess 238U, many of those with low (230Th/232Th) are in isotope equilibrium. The excess 238U is attributed to the preferential mobilisation of U in hydrous fluids from the subducted slab within the last 100,000 years, whereas the low Th isotope ratios in the higher-K arcs are primarily due to the introduction of subducted sediment. Preliminary results from mineral separates from lavas on Soufriere on the island of St. Vincent indicate that some of the minerals crystallised up to 50,000 years prior to eruption.

Jan 1, 1995

Heap leaching of copper sulphide and oxide ores' has been conducted at Rum Jungle since the end of 1965.A review of operations was made and this led to an examination of some theoretical aspects of copper sulphide heap leaching. Ox,ygen diffusion was indicated to be the factor controlling copper leaching rate at Rum Jungle and in other similar operations. Suggestions are made for measuring the heap leaching rate. Prediction of full scale operational results from pilot scale testwork are discussed.

Jan 1, 1969

By Radenkovic C, Ivkovic S, Minic I

The model, already tested and applied, enables a highly efficaceous solution of the problem of issuing instructions for interested services on the basis of known contents of in- dividual stages of mine mechanization repair and known time intervals between repairs for specific machines and total mechanization. Application of the model provides work orders for all types of repairs for specific machines or systems, and orders for the commercial department regarding spare parts Supply.

Jan 1, 1977

By R Piper

The Yabulu Nickel Refinery commissioned in 1974, processes lateritic ore via a modified Caron process to produce high quality nickel and cobalt products. The Greenvale orebody provided the sole source of feed to the plant until 1990 and with well-blended mineralogy, it resulted in stable and predictable plant performance, allowing the operating focus to be on reducing energy consumption and increasing ore throughput. This approach provided better economics than pursuing increased reduction efficiency. From 1990, increasing quantities of lateritic ore were imported from Indonesia, Philippines and New Caledonia. This introduced considerable variation in ore blends and instability in plant operation but also provided the opportunity to treat higher grade ore blends which yielded higher reduction efficiencies. Ore reduction is conducted using 12 Herreshoff multiple hearth reduction furnaces, using heavy fuel oil as reductant. The æROASTERÆ Project was approved in November 2000 with the primary objective of improving Nickel reduction efficiency by: Stabilising Roaster Operation via a structured program including focused maintenance efforts, capital equipment upgrades, new process measurements, process re-design and improvements to operating skills and process troubleshooting. A structured technical program including laboratory and plant studies using one plant furnace as a pilot unit to develop improved knowledge of how the reduction process proceeds in the Herreshoff furnace. Armed with this knowledge, optimised process conditions and a reduction process model were developed contributing to a significant demonstrated reduction efficiency improvement. Technical input to the project was provided by QNI with Hatch providing the engineering and project management for the $8.5 M capital work. Execution of the work included extensive consultation with the plant operators and close cooperation between the Hatch project team and QNI operations personnel ensuring installations were completed with minimal production disruption. A strong focus on safety management resulted in a number of brownfields project relevant safety initiatives being implemented resulting in project completion without a serious injury.

Jan 1, 2002

By A Muhairini, M Eggers, J Smith, H Baxter

Detailed geochemical analysis of cored and non-cored drill hole data was used to characterise and model the Cenozoic detrital valleys of several deposits within the southern Pilbara region, Western Australia. The purpose of this modelling was to better characterise and understand the relationships between the various geotechnical units comprising mixtures of rock and soil for the purposes of slope stability and depressurisation studies.This paper presents data from several valleys where geological, geomorphological and climatic processes have resulted in the deposition of heterogeneous detrital rock and soil sequences. Seven primary detrital units are recognised as occurring within all the valleys studied, suggesting that the geological processes involved in the erosion and deposition of the units were widespread. Geochemical assessment of cored and non-cored data suggests correlatable geochemical signatures can be recognised for each of the units; however, local variability in the groundwater history of individual valleys is demonstrated by late-stage carbonate precipitation recognised both in the core and through the geochemical signatures, which has resulted in alteration of the parent rock/soil material. This paper discusses how the carbonate alteration may lead to improvements in rock/soil mass strength of a clay unit by comparing laboratory strength test samples of the same parent material with varying degrees of precipitate alteration to those with no discernible carbonate alteration. Following from this, correlations with geochemical assay results have been derived, whereby zones of more favourable strength conditions may be modelled through assessing areas of analogous geochemistry.The paper demonstrates how geochemical assessment can lead to improved geotechnical and hydrological modelling for a detrital valley system without the need for significant coring and laboratory testing. This in turn leads to improved confidence in the slope design and depressurisation recommendations for a slope.CITATION:Baxter, H, Eggers, M, Muhairini, A and Smith, J, 2015. The effect of carbonate alteration on detrital mass strength and implications for geotechnical slope design, in Proceedings Iron Ore 2015, pp 429–436 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

Study on Pure Mineral Flotation Tests of Low-Grade Phosphate Ore in Zhijin, Guizhou Province, China

Sep 13, 2010

By J Harmse

This paper deals with the modernisation of the brakes on an electrically coupled Blair multi-rope hoist and covers the removal of the old calliper brakes and hydraulic control system, and its replacement with brake discs, disc braking units and hydraulic control systems. The paper covers the braking requirements of the hoist, which is made up of two electrically coupled single-drum hoists, together with the theory behind the choice of brakes and control systems supplied. The paper also covers the project logistics that were required in order to install and commission the new brakes and control systems with the minimum disruption to production on the only rock hoist on a major production shaft. Items covered include the modifications to civil works, pre-installation of bearing lubrication systems, brake discs and hydraulics and the interfacing of the new hydraulic control system to the existing electric control system. It had to be designed to be compatible to a new electric drive and control system due for installation at the end of 2005.

Jan 1, 2005

The main objectives of this paper are to identify the main sources of coal dust and to investigate measures for minimisation of dust generated at these sources at the Bukit Asam open cut mine, on the island of Sumatera, Indonesia which uses a

Jan 1, 1994

By D Craw, R Norris

The Golden Bar pit is part of the Macraes mine, the largest gold mine in New Zealand. The Macraes mine is mainly developed in the late metamorphic Hyde-Macraes Shear Zone. However, the Golden Bar pit was developed in a mineralised zone about 200 m structurally above the Hyde-Macraes Shear Zone. The host rocks are dominated by massive quartzofeldspathic schist (5 - 10 m layers) with minor intercalations (1 - 5 m scale) of micaceous schist. All the host schist has disseminated pyrite (micron to mm scale) from pervasive late metamorphic hydrothermal alteration.   In addition, there has been more localised (metre scale) relatively intense hydrothermal alteration controlled by shears subparallel to foliation. Gold occurs in three types of mineralised rock: silicified schist, which dominates, fissile black sheared rock, and cross-cutting quartz veins. There are three principal structural zones in the deposit: 1.   a strongly sheared micaceous and graphitic zone at the base of the structural sequence; 2.   a weakly deformed schist zone cut by relatively flat-lying (= 20¦ dipping) quartz veins; and 3.   a stack of imbricated schist pods and deformed silicified schist confined between two sub-parallel low-angle (ca. 30¦) shears.   These structural zones were juxtaposed during thrust deformation. The lower black shear zone has m-scale folding and over-thrusting packages, kink folding and foliation stacking with associated striations that imply west-directed thrusting. Striations and imbrication geometry between the upper two shears imply oblique thrusting that was directed towards the west. Post-mineralisation normal faults locally disrupt the mineralised zone. The Golden Bar pit mineralised zone has some of the structural and mineralogical characteristics of the main Hyde-Macraes Shear Zone, and may be genetically related.

Jan 1, 2006

By J Wei, A Yo, R Levy

Waste water reuse from municipal and industrial effluents is becoming increasingly important in many areas around the world. Water scarcity, local regulation and environmental impact are driving many industries like coal and copper mines to reuse the large volume of waste water they produce. For example, the Chinese coal industry generated about 4.2 billion tons of mine waste water in 2005 of which only approximately 30 per cent was reused. Coal energy represents 76.6 per cent of the total energy generated in China in 2007 and most of the coal-fired power plants are located in north-west of China, which is a water stressed area.The selection of mine waste water treatment process is challenging as the effluents typically contains high levels of organic compounds and salinity and their composition can vary significantly. In recent years there has been a growing interest in the integration of ultrafiltration (UF) and reverse osmosis (RO) membrane technologies for mine waste water treatment and reuse.In this paper, an overview of the design and performance of ultrafiltration and RO membranes applied for reuse of mine waste water are discussed. A study was carried out in two effluents treatment plants treating copper and coal mine waste water, which are located in Chile and China respectively. The following topics will be discussed to demonstrate the performance of an integrated membrane system in mine waste water reuse: The main challenges from copper mine waste water treatment: high level of chemical oxygen demand (COD); high level of total suspended solids (TSS); high salinity; high concentration of silica, sulfate, iron and other contaminants; and fluctuation of raw water quality. The main challenges from coal mine waste water treatment: high level of total dissolved solids, and waste water quality fluctuation. Design parameters for waste water treatment systems: Selection of pretreatment for dual-membrane system in the copper mine: Clarifier with coagulation and flocculation to remove high TSS; Dissolved Air Flotation (DAF) to remove non-settling solids; Media filtration to handle fine solids and particulate organics; Activated Carbon filters (ACF) to remove dissolved organics, colour and odours. Selection of UF and RO membranes and specific design of their recovery, flux, chemical dosage and cleaning regimes. Finally, the performance of UF and RO, including the main fouling factors and efficient cleaning procedures, will be presented and compared to the design parameters to demonstrate the efficiency and performance of the selected integrated membrane systems in each case.

Jan 1, 2009

The number of employees required to operate a continuous operation was determined. The fixed and variable costs of the operation were separated, generally along the lines of labour and stores components. Proprietary `MicroPlanner' scheduling software was used to assess resource utilisation under the constraints generated by seven-day operation to determine the level of resources required and ensure that the maximum use was being made of all resources. The mine economic model was used to account for both the fixed and variable costs of the various task to determine the cost and net revenue of the various scenarios. The analysis indicated that mine output could be increased while reducing the unit production cost. Several eight- and 12-hour, seven-day rosters were sourced and ranked for their potential to improve production and communication, and for their effect on employee health and lifestyle.

Jan 1, 1995

By Y Yamaguchi, S Nomura, M Matsumura, C Kamijo

In order to increase productivity and decrease reducing agent rate (RAR) of blast furnaces, slag content of sinter ore must be decreased. However, gangue content in iron ore tends to increase because of resource depletion. Therefore, amount of high-grade concentrate in sinter ore feeds should be increased, but this situation causes a decrease in permeability of the sintering bed so that the productivity of sinter process decreases. In order to increase the amount of concentrate, NSSMS has developed the P-type separate granulation method, RF-MEBIOS and SPEx II technologies. These technologies have been introduced to actual sintering machines. In this report, a new technology using microparticles of iron ore is proposed to increase the amount of concentrate in sinter blends. Basic experiments simulating the sinter making process using microparticles of iron ore were undertaken. Crushed pisolite, containing >60 wt per cent -10 µm was prepared for binder. The pisolite microparticle binder was mixed with another Australian sinter feed ore in a high-speed agitating mixer. They were mixed for about one minute, and then granulated using a pan pelletiser. After that, they were added to another raw material mixed by a drum mixer, and then charged in a pot for a sinter pot test. As a result, when the amount of concentrate increased from 13 wt per cent to 20 wt per cent, productivity was almost kept constant using pisolite microparticle binder.CITATION:Kamijo, C, Yamaguchi, Y, Matsumura, M, Kawaguchi, T and Nomura, S, 2017. Development of an iron ore microparticle binder for increasing the concentrate content of sinter blends, in Proceedings Iron Ore 2017, pp 69–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By B G. Lottermoser

Field and laboratory data combined with computational modelling have been used to predict the pit water quality for the Highway Reward mine. Open pit mining of the Highway Reward copper-gold deposit has produced a final mining void with a diameter of 600 m and a depth of 280 m. This void will be left to fill with ground and surface water once pumping of pit water ceases. Several leaching tables were constructed to simulate weathering reactions and surface water run-off in the major pit wall units during a 200-day leaching experiment. To date, about three-quarters through the experiment, combined run-off from these cells has reached a pH

Jan 1, 2003

The effect of temperature, time and SO2 concentration in the atmosphate have been studied for a complex Pb-Zn concentrate, which contained four sulphides and some organic material, in order to determine optimum roasting conditions. Under static roasting conditions virtually complete sulphation was achieved after roasting at 650¦C.2 hours in 10% SO2 in air. Both zinc ferrite and zinc silicate were observed to form early in the roasting, but continued exposure to SO2 -containing gases caused decomposition of these as the roasting time increased. Water and acid solubilities of iron, silica, calcium, magnesium and aluminium in the calcine were determined, as a function of roasting time, temperature and atmosphere composition.

Jan 1, 1970

By Kleine T. H

Blast design involves many engineering constraints and objectives. Some of the more important include the implementation costs, the desired fragmentation and shape of the muckpile. A spreadsheet has been developed to allow blast design options such as burden, spacing, blast hole diameter, decking and explosive type to be varied. As any option is varied the spreadsheet recalculates and graphs the expected implementation costs, fragmentation and muckpile shape in seconds.The spreadsheet extends the philosophy of simple robust fragmentation prediction (Cunningham, 1983) to include similar models for explosive detonation (with respect to explosive type, age, blast hole diameter and density) and muckpile shape (with respect to burden, spacing, charge location and weight). The new empirical models for explosive detonation and muckpile shape prediction have been calibrated successfully for one situation and are now undergoing further field trials.

Jan 1, 1992

By Woodcock JT

This paper deals with some innovations and current proposals for the treatment of gold ores and considers the possibilities of incorporating new developments in new or revised ore treatment flowsheets. The main topics considered are I. typical practice in relation to the size of gold particles, 2. concentration of coarse gold, 3. leaching reagents, 4. in situ leaching, 5. heap leaching, 6. carbon-in-pulp adsorption, and 7. treatment of complex ores (gold in pyrite, gold tellurides, and carbon-containing ores).

Jan 1, 1982

By G Johnson, S Michalek, N Redman

As the modification of the 2009 Mill OperatorsÆ Conference theme from æmilling through the boomÆ to æthe boom û experience gained and lessons learnedÆ exemplifies, comminution practitioners are facing a series of challenges in the dramatically changing mining environment. One of the main problems plant managers have been facing during the boom times has been the severe metallurgy skills shortage and high staff turnover, both factors that can cause difficulties in mill liner management. Many of todayÆs mill managers are now also more than ever faced with the need for cost-cutting in order to continue operating viably. Amongst other potential target outcomes such as maximised throughput, MillMapperÖ, a tool for mill condition monitoring and mill performance optimisation, can be utilised to address these issues. This paper demonstrates how MillMapperÆs quantifying decision making tools can serve to be in control of managing mill liner and production issues, and how it can form the basis for mill cost savings without the risks normally associated with conventional methods or the lack of using any condition monitoring methods. MillMapperÖ is currently being referred to at a rate of approximately 150 surveys and associated reports per annum at processing plants in Australasia, South America and Africa. Examples throughout the paper provide insight into how the presented sample set of users have extracted benefits that could have otherwise not been safely or at all achieved.

Jan 1, 2009

Study on the Effects and Mechanics of Na2SO3 to Chalcopyrite and Galena

Sep 13, 2010

The phosphatic overburden of Christmas Island is a lateritic soil and consists dominantly of crandallite and millisite. These minerals are polymorphs of general formula, (Na,K)x Ca2-x (Al, Fe)6 (PO4)4 (OH)10-x (2+x) H2O. Iron occurs only in millisite. Both minerals exhibit similar thermal transformations, dehydroxylating near 600¦C and recrystallizing above 800¦C. Dehydroxylation results in crystal structure collapse but retention of crystal morphology. Ggethite, boehmite and apatite are minor constituents of some-of the phosphatic Soils.

Jan 1, 1971

Reconnaissance geochemical exploration in the vicinity of low angle detachment faults which bound the core of the Paparoa metamorphic core complex yielded Au up to 14 ppm, with 35% of greywacke, granitoid and quartz vein samples in the northern range exceeding the 0.01 ppm detection limit. Au is associated with Ag, As, Sb and Cu anomalies consistent with epithermal-type mineralisation. The Ag and Cu anomalies also distinguish this mineralisation from older, mesothermal Au deposits widespread in the Ordovician 'slate belt' greywackes, which comprise much of the upper plate of the core complex. Baryte, molybdenite, fluorite and stratiform U mineralisation in the northern Paparoa Range may also be related to hydrothermal activity along the detachment fault zones.

Jan 1, 1995