Search Documents

By J L. Kanau

In this study some drawbacks of using Bond grindability as a measure of grindability characteristics for mill control have been discussed. After reviewing the merits of alternative methods of determining the Bond grindability published in the literature, a new alternative method has been proposed.

Jan 1, 2000

This technical note describes a problem with WANG82, a ventilation network analysis programme. The problem was highlighted by Renison Ltd when using the programme on large, complex networks. Under certain circumstances the programme produced incorrect results or failed to converge to a solution.

Jan 1, 1986

By Buizen M

An investigation into the mechanics of sub-surface deformation caused by caving of the extracted area behind retreating longwall faces has been completed by the Subsidence Engineering Section of the New South Wales (NSW) Department of Minerals and Energy. Changes in strata bulk permeability were also measured by standard packer tests undertaken before and after mining. The strata movement was measured by a multi-wire borehole instrumentation system consisting of mechanical anchors installed at different horizons in a borehole extending from the surface to the coal seam. The mechanical anchors were collected to suspended weights on the surface by stainless steel multi-strand wires. The movement of these weights was monitored as the longwall face approached and retreated past the borehole. The anchors did not move significantly until the face went past the borehole. For subcritical extraction geometry with the extraction width to mining depth ratio of 124, the caving zone extended to roughly 9 times the extracted seam thickness above the seam roof. Tensile strains within the overburden tended to be much more closely related to stratigraphy than to the proximity to the extracted seam roof. Larger tensile strains were associated with layers of sandstone, siltstone and conglomerate, whereas layers of mudstones, claystones and coal underwent much smaller strains indicating subsidence in blocks. A beller correlation was observed between pre-mining Rock Quality Designation and permeability than between rock type and permeability. This correlation was less evident in the post-mining core logs. There was an overall increase in bulk permeability after mining.

Jan 1, 1990

By Zervoudis J

Limitations of current touch-up solders for galvanised steel include coating thickness control problems and poor corrosion and abrasion resistance as well as health and environmental concerns due to toxic constituents such as lead. This paper reports on progress in ILZRO-sponsored research to develop an improved touch-up solder. Encouraging results were achieved in torch soldering trials with experimental zinc-tin-based alloys. Mouldability and coating thickness control were achieved over a practical working temperature range in which the solders consisted of a viscous mixture of solid primary zinc phase particles in a liquid zinc-tin eutectic matrix. The mouldability was dependent on the microstructure of the solder sticks, and optimum structures could be obtained through control of casting solidification rates and by the addition of small amounts of copper. Hardness, abrasion resistance, adhesion and corrosion tests on experimental Zn- (40 - 50 per cent) Sn-I per cent Cu also showed improved performance over lead-tin-zinc solders and compared the effects of tin content within this range. Atmospheric corrosion testing and optimisation of alloy composition and methods of solder stick production are continuing.

Jan 1, 1993

By Aziz NI

There are a number of methods available for the determination of the fracture toughness of rock. Some of the most recognised methods include the hollow pressured cylinder, the short-rod, the chevron - edge-notched round bar in bending and the disc-shaped compact specimen. Most of these tests are difficult and expensive to conduct. In this paper the simple Brazilian testing of discs for tensile strength has been used to determine their fracture toughness. Tests were conducted on six different rock types and the values of the fracture toughness obtained for each type are in close agreement with the results of the well recognised the chevron edged types. Details of the tests, and analytical validation of the technique, are presented

Jan 1, 1992

Performance trials followed the commissioning of three large mine fans at Mount Isa in 1965. Actual performance characteristics were determined. These were in good agreement with predicted performance. Piezometer rings for volume flow and pressure measurement were calibrated, and the performance of some aerodynamic components of the installation was studied.Test equipment, preparation, and conditions are described.

Jan 1, 1967

By Y B. Kang, Y J. Park

Ti-added ultra-low carbon (ULC) steel is produced by adding Al and Ti during the secondary refining process to deoxidise molten steel and to bind C and N which are detrimental to the deep drawing quality of the steel product. However, the production of Ti-added ULC steel faces challenges, including submerged entry nozzle clogging and surface defects on cold rolled coils. The troubles were often attributed to ‘Al-Ti complex inclusions’ in the molten steel. However, the evolution of oxide inclusions including their stability has been still unclear. In the present study, the evolution of these inclusions in Ti-added ULC steel was investigated by phase diagram measurement, CALPHAD thermodynamic modelling, high-temperature stability test for the oxides, and observation of transient behaviour of oxide inclusions in the steel. The phase diagram of the Al-Ti-O system was elucidated with an emphasis on oxygen potential, which significantly controls the stability of the oxides. CALPHAD thermodynamic models and a self-consistent database were developed. The transient behaviour of Al-Ti complex inclusions in Ti-added ULC steel was observed in situ using a confocal scanning laser microscope. This was additionally validated by the new thermodynamic model. The equilibrium phases of the oxide inclusions were investigated using a high-temperature resistance furnace, and were analysed using a secondary electron microscope, energy dispersive spectrometer, and electron back-scattered diffraction. By considering the morphology and crystal structure of these inclusions, the evolution of Al-Ti oxide inclusions was elucidated. Various behaviour of Al-Ti inclusions and their influence on steel cleanliness are discussed.

Aug 21, 2024

A Modelling Approach Using a Back-Calculated Induction Time to Predict Recoveries in Flotation

Sep 13, 2010

By D M. Aranha, A R. Cabral

Theories on the origin of the Itabira iron formation (itabirite) in Quadrilßtero Ferrffero (QF), as elsewhere in the world, are restricted by the apparent lack of adjoining volcanic units, severe syndeformational metamorphism and deep weathering. Besides the three types of iron formations at QF (siliceous, dolomitic and amphibolitic; Dorr, 1969) we include a fourth type initially described as ocherous, goethitic, limonitic or even yellow iron formation. Considering its high magnetite content, it has been described as yellow magnetite itabirite (Pires, 1979). It was reported as formed by the alteration of the dolomitic itabirite (Dorr, 1969) although the anomalous Al2O3 contents are high for normal weathered itabirite. The yellowish magnetitic itabirite occurs at the bottom of the Itabira Iron formation, along the contact with the Batatal schists, and at the top units of the Itabira, within the Gandarela Formation. Within the magnetitic itabirite at the Tamanduß iron ore mine there are metric zones, concordant to the bedding of pillow-like structures, exhibiting a porous core, surrounded by an intermediate, more granular zone with numerous, minute rounded cavities grading to an external, fine-grained zone with much less minute cavities. In the external portions of some pillows a breadcrust type structure, derived by quenching with the water can be observed. In some other zones, such as the Barreiro hill, an outer, vesicular, whitish yellow, 5 - 10 mm thick, band grades to an aphanitic, isotropic band. The vesicles are slightly flattened against the band surfaces. The existence of fragmental layers showing flowage and fragment alignment, kaolinitic laminas and vesicles filled with kaolinite at Barreiro Hill and Capitpo do Mato Mine represent mesoscopic structures, indicators of a possible volcanic origin. Chemical compositions of the magnetitic itabirite from a wide area in QF revealed a relatively high Al2O3 content, consistent with a volcanic origin.

Jan 1, 2005

By Corbett GJ, Leach TM

The Nena Cu-Au high sulphidation deposit has formed within the Frieda River Intrusive Complex in association with a major dilatant structure. Multiple intermediate intrusives of Miocene age are localised by a splay (Frieda Fault) of the Fiak-Leonard-Schultz Thrust, a several hundred kilometre long structure, formed parallel to the accretionary prism of northern Papua New Guinea.The high sulphidation systems including Nena, crop out as narrow silica-alunite ridges extending for up to 5-6km in length within a dilational structural environment. Alteration at Mena exhibits two phases of hydro-thermal activity: an initial stage, inferred to be volatile-rich, which has produced zoned alteration; and a later phase, postulated to have been a liquid-dominated fluid, which has brecciated earlier alteration zones and deposited gangue phases as well as Cu/Au-bearinq sulphides in open spaces.

Jan 1, 1994

INDEX OF CONTENTSIntroduction.Systems of classification of coals.RankClassification of Australian coals.Defects of systems in use in other countries.Indexing by Fuel Ratio.Classification by Ultimate Carbon/Ultimate Hydrogen.Relationship between Fuel Ratio and ultimate composition.Suggested convention for classification.Origin and Evolution.Notes on directions of change of composition on Carbon Hydrogen chart.Summary and conclusion.Acknowledgments.Bibliography.Appendix.

Jan 1, 1948

By L Soares, W T. Hennies, F Fujimur

Barra Bonita reservoir, located in the Sao Paulo State, Brazil, has been mainly used for local navigation and electricity generation to supply a prosper region in the country. Sand mining activities in that area have an important social and economic meaning for the local community. In this reservoir there are several sand mines that produce around 45 000 m3 of sand a month. These deposits were rich in material used as concrete aggregate in the civil construction. However, nowadays a significant increase in the demand of gravel can be observed, representing a serious productive problem. This material hasnÆt been well accepted by the market and, through the years, it was disposed at open sky in piles as waste deposits. This deposits have caused environmental problems like visual impact, reduction of free spaces outside and inside the mine, source of material to erosion and sedimentation processes in lower areas, flooding as a result of the filling up process in the drainage system, among others. For a lack of an appropriate technological characterisation, this material have been mainly used to pavement internal and external areas in the mine, with lower cost associated. With the purpose of evaluate the usefulness of this material in the conventional concrete, there were conducted several tests in the disposed residue including petrographical, physical, and chemical characterisation. The petrographical analysis and the preliminary results of the study showed that the material reacts with the alkalis that are present in the conventional cement (CP-II-E-32). In order to make the application technical and economically possible a research was developed seeking forms to correct this characteristic by adding special cements with high pozzolana content. The results of the technological, physical and chemical characterisation of the products indicated the technical viability of the use of that material. The study also allowed projecting environmental improvements resulting in the elimination of the waste piles.

Jan 1, 2003

By Matsuo T, Uga Y

The tunnelling work to construct a sewage trunk line designed by the Sewage Bureau of Kobe City along north side slope of Rokko mountain range incorporated an all ground condition type (broad spectrum) TBM with slurry transport system with jet pump manufactured by Kawasaki Heavy Industries, Ltd. Boring dia. of the tunnel measured to 2.0 m. The construction planning and implemen- tation were done by Ohbayashi Corporation, the general contractor. The heading way was 3342.4 m in overall length.; construction work ran from April '84 to June '85. The max. daily progress marked 31.9 m and the max. monthly progress 493.1 m according to the relevant record. The machine proceeded with the work under geological conditions featured with conglomerate, rhyolite, tuff breccia and slate, whereby soft soil zone mostly of clay was encountered in a limited area. In the latter case, however, steel segments were substituted for supporting steel ribs. The tunnel was routed beneath a meandering road with the result that more than 40% of overall length show a curvature of 50 to 200 m radius.

Jan 1, 1987

By Corner NG

A sea bed sampling programme by CRA Exploration Pty. Limited over an area of 12000 km offshore from Westland, Southland and Otago, New Zealand, led to the discovery of the Harvester Prospect, an area of some 67 km2 which averaged 189 mg/m3 gold in surface samples. This area was in water depths of 70 to 100 m and contained a high grade core of 33 km2 which averaged 283 mghn3 gold. The gold recovered was fine grained, averaging 124 microns, and indicated a potential resource of approximately 10 t of gold per metre of thickness. Interpretation of existing seismic and geological data suggested that the gold anomaly may be associated with a unit of sediments 10-40 m thick, probably deposited during a lower sea level stand. Two initial attempts at vibrocoring the anomaly produced inconclusive results. In 1989 a much more powerful vibrocorer with scaled up support facilities and a dedicated 24 It turnaround laboratory were employed. The final results clearly showed that the gold was from an uneconomic surface enrichment.

Jan 1, 1990

Recycling and Recovering Fine Particles from Auto Shredding Residue (ASR/SR) to Conserve Raw Materials and Protect Environment

Sep 13, 2010

The large, high grade 3000 and 3500 copper orebodies at Mount Isa lie greater than 1200 m below the surface, and partly beneath the silver-lead-zinc mining operations at the Isa Mine.Since discovery over 30 years ago, the primary data acquisition programs have been integrated with long-term copper production strategies. These potentially sizeable and distinctly separate accumulations of copper mineralisation are the only sources capable of supplementing a decline in output from the 1100 orebody in the 1990s. Within a decade these deeper copper orebodies will become the major source of copper ore.

Jan 1, 1993

By Floyd J. M

The recovery of gold from refractory ores and concentrates can be achieved in a number of ways using roasting and leaching procedures. The Sirosmelt system introduces a new approach to the recovery of gold from these materials using smelting procedures. Laboratory studies were carried out to establish procedures for operating the Sirosmelt system for recovery of gold and associated valuable elements from an ore containing 17.5 g/t gold and a concentrate containing 22 g/t gold as well as substantial copper levels. Copper, iron, lead and matte were evaluated as collecting phases for the gold. The ore smelting procedure recovered 80-90% of the gold whilst smelting concentrate gave 98-99% gold recovery.

Jan 1, 1987

This paper describes a mobile laboratory developed specifically for nickel prospecting, and which was designed to be operated by sub-professional staff in remote areas independently of established laboratories. An atomic absorption spectrophotometric procedure was used to determine nickel, cobalt, lead, zinc, and copper ID latentIc and sulphIde samples, with a detection limit better than 25 µg/g for all elements. The procedure was applicable to both soil and drill samples and the accuracy of the procedure, which was ±5 per cent relative at the 1,000 µg/g level was sufficient for the preliminary assessment of mineralized samples and the control of drilling operations. The analytical procedure and the means taken to ensure the necessary reproductibility and accuracy are described. One operator can carry out 400 elemental determinations per 8-hr day at an approximate cdst of 6 cents per elemental determination. The results are returned within a single day, a factor which can contribute materially to the efficiency of drilling operations.

Jan 1, 1970

By Abell RS, Wyborn D, Solomon M, Stuart-Smith PG, Henderson GAM

The two major massive sulphide deposits in the Silurian rocks of southern NSW, Captains Flat and Woodlawn, differ from classical Kuroko deposits in several ways, e.g. they lie on the flanks of felsic volcanic piles in volcano-sedimentary marine sequences, are relatively thin and large compared to individual Kuroko deposits, show prominent banding in lead-zinc ore, and contain arsenopyrite. Qualified stuctural and stratigraphic correlations of the various fault-bounded remnant Silurian sequences that host these deposits provide the basis for a new interpretation of the regional geological setting that also differs from that of the Kuroko deposits (Ohmoto, Tanimura, Date, Takahashi, 1983), and sheds further light on the distribution of volcanogenic massive sulphide deposits in the Silurian rocks of NSW.

Jan 1, 1987

By Michot LJ, Kongolo M, De Donato PH

Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS), Hallimond tube flotation tests and microelectrophoresis measurements have been used to investigate the reactions involved in the adsorption-ion of K-amyl xanthate on finely ground pyrite. Pure pyrite was finely wet ground, at different pH values, in specially built laboratory stainless steel or iron rod mills. Amyl dixanthogen was the only product identified on the surface of pyrite when stainless steel rods were used. When iron rods were utilised, ferric xanthate and physically adsorbed xanthate ions were observed in the superficial phase. The use of iron media was found to depress slightly the floatability of the mineral.

Jan 1, 1993