Search Documents

By T Roberts, D Faulkner, G Watt

Traditional mechanised resin rock bolting in hard rock underground mines requires the installation of resin capsules into a pre-drilled hole prior to the rock bolt being spun into a hole to mix the resin and set the bolt in place. In poor rockmass conditions, especially at depth or in highly altered faults and shears, the condition of the holes often deteriorates as the poor ground around it unravels and falls into the hole. This results in partially or fully blocked holes that either damages the resin capsule when they are being inserted into the holes or prevent it entirely until the hole is continuously cleaned of debris. This deterioration of the hole condition, and continuous need to clean and re-drill holes, also increases the diameter of the hole which in turn affects the continuously mechanically coupled anchorage mechanism of the rock bolt to the rockmass as there is simply not enough resin in the hole to fill the annulus between the bolt and the rock. This results in a large increase to critical heading cycle time and, more importantly, results in the rock reinforcement not performing as per design specification and increases the risk of instability. To overcome the quality control issues with resin bolt installation in poor ground, a single pass drill, install, inject and tension self-drilling resin bolt application was designed and implemented for use in such conditions. This system allows the operator to inject a two part polyester resin through a self-drilled hollow bolt to mix and fully encapsulate the rock reinforcement. The self-drilling bolt allows for post injection of the hole after the bolt has been installed into the rock and gives the operator manual or automated control on the amount of resin used in the hole to ensure complete encapsulation and continuously mechanically coupled anchorage to the rock. This allows the reinforcement to work as designed and provide the Geotechnical Engineer extra quality control confidence in these conditions. The implementation of this single pass resin bolting system resulted in significant decreases to the resin bolting cycle time and rock bolt quality control failures. In this paper the design, implementation and embedment into the development cycle will be discussed and the in situ quality control checks used to validate the increase in rock bolt installation quality will be shared. CITATION:Watt, G, Roberts, T and Faulkner, D, 2018. Single pass drill, install and inject self-drilling resin bolt application in poor ground, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 323–343 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By C Rizzardi, M Callahan, J Mahon

Henderson Operation’s underground molybdenum mine has been in production since 1976. Since that historic date, more than one billion pounds of moly has been produced, and over 120 Mt of ore extracted from three different levels and many different panels. The safe and successful operation of Henderson has been, and will continue to be, dependent on utilising an increasingly sophisticated fleet of equipment, advanced designs, innovative mining techniques, best practices in maintenance processes, improvements in crushing and conveying systems, and most importantly, the training and mentoring of the underground staff. These ‘professional mining technicians’ have been essential in the safe and efficient operation and maintenance of the underground mine and convey systems, and will drive the continuous improvements needed to keep Henderson competitive in the growing global market.CITATION:Callahan, M, Mahon, J and Rizzardi, C, 2016. Development of the professional mining technician – Henderson’s underground mine continuous improvement program, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 161–166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

A comprehensive analysis of rock structures in non-oriented (axially oriented) drillcore is now available (Laing, in press). The system embodies new concepts which better equip the geologist and engineer to deal from the outset with optimising the acquisition of structural information in drillcore, logging: interpreting, and graphically presenting the results. The few existing techniques for determining orientations of structures are augmented by a wide range of new techniques, and all are brought together into two solution types by considering the underlying Euclidean geometries. Analysis of these solution types in terms of what data are required to implement each solution and what assumptions need to be made, leads to strategies which facilitate intelligent design of different drilling programs for blind and outcropping situations. Drillcore is variably structurally fertile, depending on the number of different structures present. This concept fosters the selective logging only of the more fertile core. Drillholes are also variably fertile, depending on their orientational relationship to the structures in the host rocks. Structural parameters are either vectorial or non-vectorial. Vectorial structures parameters comprise normal structural orientations plus polar vectors like vergence, younging, shear sense and so on. They can be determined by one of two solution types: external solutions, which use an external reference structure to fix the drillcore and thus permit orientation of all structures within that core, and internal solutions, which use orientational data from a selected structure at three or more different drillhole orientation to determine the unique orientation of that structure, without reference to any external structure. Both solution types rely on constant orientations (orientational stability) of the selected structure, but the internal solution actually provides its own test of orientational stability. External solutions are the norm in outcropping situations and internal solutions are invaluable in blind situations. In blind situations sequential "internal then external" solutions can be used respectively to provide a reference structure and then use this for subsequent external solutions at individual points downhole. Blind prospects can now be drilled and interpreted as easily as outcropping prospects. Each solution type has its own optimum requirements. External solutions are ambiguous for certain orientational relationships between the drillhole and the reference structure (for example, a perpendicular relationship), hence drillholes in which external solutions are planned should be designed to avoid these orientations. Internal solutions are ambiguous for straight drill paths, and are most unambiguously resolved when the drill path attains maximum drillhole dimensionality, that is, it occupies a wide variety of orientations in 3D space; hence drillholes in which internal solutions are planned should be designed as combinations of non-parallel holes or as individual strongly curved holes. For both solution types an understanding of the kind of structural fertility required leads to intelligent design of drill paths, which is termed structural drill targeting. It is distinct from spatial drill targeting, which is the process which defines and (x,y,z) point-or volume-target. Effective design of drilling programs requires both structural and spatial targeting. The external and internal solutions for vectorial parameters are implemented via (1) visual (qualitative), (2) stereographic, or (3) core orienting frame procedures. Each of these has its own advantages. Stereographic procedures have been simplified via the erection of a drillcore reference frame in which three fundamental angles are defined, and the formulation of an all-inclusive set of stereographic recipes for determining orientations from the measurement of these angles. Non- vectorial structural parameters comprise an ad hoc array of useful measures which are simply described by numbers. Examples are angles between structures, and density of structures. Such parameters (some of which provide useful vectors toward ore bodies) are invaluable in drillcore because they can be measured and recorded rapidly, without determining the orientation of the core. In a summary, non-oriented drillcore can now be structurally mapped exactly as if it were outcrop. Interpretation of the significant volume of unique structural information which is beginning to flow from this system can be optimised by using, in addition to the conventional cross section and longditudinal section, three new modes of presentation. The natural cross section is that section in space normal to a principal structure of interest. It is a section in which it is advisable to drill to obtain certain structural information, and in which the results need to be presented. A newly defined unique cross sectional orientational symbol is recommended for dramatic improvement in the quality of information presented in cross sections. Stacked level maps are a powerful adjunct to cross sections.

Jan 1, 1990

The changes in layout and design over 48 years, from the first crushing and shiploading plant installed at Whyalla in 1915, up to the present plant being built at Koolan Island, Yampi Sound may be summarized as follows.1. Smaller motors and lower power consumption have resulted froma. oil lubrication, where practicable, in place of grease,b. a high pressure "oil-lift" device to reduce starting torque in crushers with white metal bearings, andc. roller bearings in place of white metal.2. Short centre drives with pivot-based motors permit controlled loads on bearings and a reduction in size of crusher houses and motor rooms.3. Dust proofing and pressurising of crusher houses and motor rooms reduces working temperatures and improves cleanliness.4. Variable speed pan feeders give improved plant control, with the use of one man only, and remove the need for large surge bins between crushing stages.5. The use of diesel quarry trucks to dump ore through a "drive over"tip results in faster truck cycles.6. Elevated cylindrical silos with air operated chutes, replace long horizontal storage bins with multiple manually operated side discharge chutes for loading rail cars, and give faster and more accurate truck loading. The silos are charged by belt conveyors with automatic distributors.7. Increased shipping bin capacity (40,000 tons at Whyalla and 6O,OOO tons being built at Koolan Island) caters for the bigger vessels now in use and envisaged for the future. Automatic travelling distributors deliver ore to the bins in layers to ensure, maximum mixing and a more uniform grade for blast furnaces.INTRODUCTIONThe Broken Hill Proprietary Company Ltd has six major crushing plants in Australia at its principal sources of raw material. These are at Iron Knob bench G, Iron Knob scree ore plant, Iron Baron, and Cockatoo Island, all of which are ironstone operations. The other two plants are at Rapid Bay, a limestone quarry, and at Ardrossan, which is the Company's only source of dolomite.

Jan 1, 1963

By W R. Adamson

Cerro Vanguardia SA (CVSA), property of AngloGold Ashanti, mines gold and silver from a system of vetiforme orebodies located in the south of the Argentine Patagonia, in the Province of Santa Cruz.Surface mining techniques are applied to develop a series of narrow pits with an average waste to ore ratio of 26:1. This quite unique constraint brings into focus the need to maximise inter-ramp and final wall angles, leading to a strong need to optimise wall control drilling and blasting in order to reduce back-break damage to an absolute minimum.The paper describes a program of applied investigation and design modification implemented during?2008?and?2009 in?two?separate pits of Cerro Vanguardia. Three distinct yet complementary damage mechanisms were identified and observed during the field components of the work; vibration induced strain fracturing, surface cratering around blasthole collars and quasi-static loading and unloading of the surrounding rock mass as a consequence of poorly controlled confinement.With these mechanisms identified, a measurement, modelling and modification campaign was conducted in order to reduce the incidence of each source of damage. Interactive design analysis and modelling, near-field vibration measurement, video capture and the application of electronic initiation technology were supported by seed wave modelling and topographic evaluation of the achieved results.Results point to the usefulness of simulation techniques for determining optimum delay timing to reduce vibration impact, while the visualisation of explosive energy distribution produced by drilling and explosive loading decisions assists in reducing the probability of over-confinement.This paper presents relevant aspects of the two fieldwork campaigns:1) describing the application of the techniques, and2) summarising the results obtained.

Nov 8, 2011

By J Centofanti, D Conti, R Riske, C Morley, A Cook

Why is it so difficult? Why are there differences throughout the resources industry in how reconciliation factors are reported and calculated? Why is there no standard formula to use? These are common questions asked when mining companies try to compare reconciliation results across operations or attempt to undertake internal or corporate governance reporting processes. For many mining companies the calculation of reconciliation factors is often a very time and resource intensive part of mandatory reconciliation reporting. Some major mining companies, that move millions of tonnes of material per annum, dedicate full time resources to the calculation of reconciliation factors. The willingness of these companies to set aside resources demonstrates the value that operations place on good reconciliation reporting. Reconciliation is about measuring the variance between two like measures at different points along the mining sequence. It can be undertaken between predictive models, forecast plans and actual measured performance. Calculations are used to derive a variance between two sections within the mining sequence, with the result being commonly known in the resources industry as a æfactorÆ. Mining companies use the calculation of reconciliation factors as key performance indices (KPIs) to provide a æhealth checkÆ of their operation, with variances often pointing to issues either with the accuracy of the original estimate or the quality of the measurement being used in the comparison. There are many reconciliation factors that can be calculated and reported. This paper will set out, clarify and provide a recommended standard means of calculating each specific factor that, where adopted by a company, will ensure compliance with the international reporting codes, such as JORC. Using case studies from Rio Tinto Group (Rio Tinto) and BHP Billiton Mitsubishi Alliance (æBMAÆ), and the authors experience across a wide range of mine sites, the outline of a generic solution for tracking a parcel of material from the pit through to the port along with appropriate reconciliation factors is provided. The intention of proposing standardised reconciliation factor terminology and methodology is to provide the foundations of a system to enable communication and comparison across different commodities, companies and mines sites.

Jan 1, 2009

By R J. Thompson

In truck-based hauling systems, the mine haul road network is a critical and vital component of the production process. As such, underperformance of a haul road will impact immediately on mine productivity and costs. Operations safety, productivity and equipment longevity are all dependent on well-designed, constructed and maintained haul roads. With the advent of autonomous haul trucks, the haul road itself becomes all the more critical to the success of these type of operations; not only in relation to mine operators requirements for safer and more efficient and predictable haulage systems, but also in response to autonomous truck manufacturers’ requirements for a more predictable and controlled operating environment. This paper presents a brief summary of the state-of-the-art in surface mine road design and then proceeds to examine the design and technological challenges associated providing a safe, predictable and affordable road for autonomous mine haul trucks. The paper serves as a basis for evaluating the contributions that enhancements in road design and management can deliver to autonomous mining operations, an initiative that also has scope for adoption within the operating life of many mines, haul roads and haul trucks.

Nov 22, 2011

By H Arvidson, B Spence, S Helm

Mining is the art of disturbing ground. All phases of a mine’s life cycle from exploration to building and operating a mine, through closure, has a physical impact on the earth. There is currently increasing public and stakeholder awareness owing to a wide range of issues including heritage protection, environmental stewardship, and social impacts therefore ground disturbance must be conducted in a way that honours and respects all agreements, regulations, legislation, and social expectations. A comprehensive ground disturbance permitting process has been developed through consultation with major mining companies and Traditional Owner groups. It operates from strategic business planning through to closure and rehabilitation. Adherence to the principles and process of permitting helps to minimise risk by ensuring that mining companies conduct their business in an inclusive, professional, reliable, and consistent manner that stakeholders reasonably expect, and that mining companies can be proud of. Built on a geographical information system, supplemented with a specialist database, this process allows request, review, and approval by subject matter experts, to operate in a common environment that is transparent, facilitates collaboration, improves efficiencies, and reduces the risk of error or omission. The application of new technology can effectively highlight changes that naturally occur in today’s dynamic ESG domain and provides the perfect platform to record actual disturbance against authorised and planned allowances. The social license to operate demands that strong governance of the ground disturbance process, described herein, can be demonstrated to any interested stakeholder, and mining companies recognise that this principle is central to the betterment of the mining industry.

Sep 18, 2023

By G Stanway, P Mahoney, C Griebel

The Mining Innovation – State of Play was initiated three years ago by VCI in partnership with the University of Western Australia. The ambition was to create a ‘think tank’ type platform to support industry discussion on how it is performing in terms of innovation at a strategic level, what needs to change in the industry ‘ecosystem’, and how businesses may more effectively develop their strategy and architecture to innovate for competitive advantage.The drivers for this ambition were straightforward. The industry recognises itself as being conservative with respect to innovation and it knows the business and community endowment dividend from getting better at innovation is large; however, much of the material that seeks to provide insight on innovation tends to be drawn from industries that do not have the same high capital, long life cycle and market uncertainty characteristics as that faced by mining. Material that does focus on mining innovation is orientated towards technical innovation, not innovation strategy. There exists a significant knowledge gap, and filling it is valuable to both mining businesses and communities.The 2014 Mining Innovation State of Play report (Stanway, Griebel and Mahoney, 2014), based on a survey of over 230 mining executives, uncovered a range of insights but left several questions unresolved. The people with the best perspective on these questions are CEOs. They can see the business issues with sufficient clarity and have the influence to shape both the industry and its organisations, as seen in Figure 1. Discussing these questions with the view to progressing our collective understanding was the primary reason this interview series was conducted.Unsurprisingly, interviewing 15 CEOs and Chairpersons from different industries and commodities, across the globe resulted in a broad range of views. The discussions were frank and often blunt in assessing the short comings in the industry and suggestions for improvement. This degree of candour is hugely valuable as a basis for improvement. In the end, four key areas emerged as a basis for improvement.CITATION:Stanway, G, Griebel, C and Mahoney, P, 2017. Mining Innovation State of PlayTM – iron ore insights, in Proceedings Iron Ore 2017, pp 439–442 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By D P. Blair

The theme of this conference is blasting productivity. This article only considers the technology aspect of this theme, and in particular, the collection and analysis of experimental data. In many cases, field trials are set up to collect data on variables such as fragmentation and vibration with the aim of comparing different explosive products and/or blast designs. An important aspect of such trials is the collection of sufficient data to draw sound conclusions. In this regard, there is no doubt that the scatter in real data is the root cause of all problems of obtaining misleading results due to an insufficient number of trials. This article shows that the typical one-off trial has a high probability of producing misleading information, which could be considered to be worse than having no information at all. Assuming that sufficient data has been collected, this article also highlights the methods that can be used to make the most of that data. These methods include the application of appropriate statistics that are dependent on the nature of the scatter in the data, and the use of some of the more recent filtering and spectral approaches that can be used to reduce the noise in measured blast signals and increase the resolution of their spectral characteristics.

Nov 8, 2011

By Robinson KJ

There has been much debate in recent years regarding the number of Geology (Earth Science) graduates produced in Australia. The key variable has commonly been assumed to be the placement of graduates in the mineral and petroleum industries. Although not wishing to deny the importance of this element, we contend that Geoscience studies should be given to a wider variety of graduates. The essence is to make students and future citizens more environmentally aware. INTRODUCTION Geoscience is fundamental to exploration and to the well-being of the minerals industry and hence the Australian economy. The value of mineral primary products exports for the past three years has been: 1895 $15.3 billion 1986 $14.8 billion 1987 $16.3 billion (Data source: B.M.R) The mining industry supplies about 40% of Australia's export earnings. However the overall value of Geoscience to the Australian economy is much greater. At the opening of the ANZAAS conference in Townsville during May 1987, Sir Bruce Watson , Chairman of the Mt. Isa Mines Ltd., made a plea for a national re-examination of the way science is taught in secondary schools. In particular he emphasized the point that the community should be more aware of the importance of Geoscience and the value of the mining industry to Australia.

Jan 1, 1989

By M Rea, E O’Connell

Decarbonising explosives manufacturing and catalysing low-carbon mining supply is a significant global challenge. Low-carbon manufacturing precincts – clusters of geographically close businesses across multiple industries that share a goal of adopting firmed renewable energy and decarbonising process emissions – offer one potential solution. In an Australian first, Orica commissioned tertiary catalyst abatement technology in 2023 to mitigate greenhouse gas (GHG) emissions at its Kooragang Island (KI) facility in New South Wales (NSW), Australia. The EnviNOx® technology (ThyssenKrupp Industrial Solutions AG, Dortmund, Germany) used reduces nitrous oxide (N2O), a potent greenhouse gas arising as a by-product of nitric acid manufacture. As a result, mining customers in NSW are now benefitting from ammonium nitrate (AN) products that are almost 50 per cent less emissions-intensive than those Orica previously offered. The $37 million project is a private-public partnership that has involved partners across Federal and State government, global engineering and technology vendors, local community groups and local carbon advisors to overcome financial barriers.

Sep 1, 2024

By E Coffison, M Gibbs, C Bennett

The sustainable management of surface water associated with coal mining and coal seam gas projects is a considerable factor affecting the global competitiveness of these resource companies operating in Australia. Management of surface water can be costly, but effective water management and hence environmental stewardship enhances corporate social responsibility and the social license to operate. The surface water issues for the two industries are comparable, yet there is currently a lack of alignment between how Queensland, where the majority of AustraliaÆs coal seam gas projects are located, manages and regulates water on coal mine projects and coal seam gas projects.This paper provides a high level comparison of Queensland legislation and highlights the lack of alignment of this legislation regarding surface water management in these two industries. Through a case study, it looks at the surface water management process at a coal mine site based on the current legislation and principals of surface water management. QueenslandÆs lack of alignment in legislation regarding surface water management in these industries is understandable given the different development paths and time scales of the two industries. The coal mining industry has developed over a long period of time and the legislation has progressed in parallel, whereas, the coal seam gas industry is relatively new in Australia and the legislation has had to advance quickly. The lack of alignment between management of surface water for the two industries creates confusion among stakeholders and this adds complexity and additional transaction costs during the exploration, permitting and operational phases of projects, including landowners who may be affected.CITATION:Bennett, C, Coffison, E and Gibbs, M, 2013. Lack of alignment between regulation of surface water management in coal mining and coal seam gas, in Proceedings Water in Mining 2013 , pp 157-162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

In practice a sampling solution is a compromise of many requirements: the sample should be representative; the sampling system should also be reliable, less than 95 per cent availability restricts the use of the assayed sample for process control purposes; no sample is the worst sample, and investment costs and installation space/layout are frequently a restriction. For instance, online X-ray analysers for process control introduce a delimitation error by the nature of X-ray physics. Thus only in special cases a relative accuracy better than three per cent relative, as one standard deviation, is achieved. A sampling system for process control needs not to be, as representative, for so many sample properties, as one for composite laboratory analysis samples. Sampling system maintenance is also an important issue. There are many sampling systems in the industry which have been difficult to maintain and are in disuse for lack of resources or incentives to keep them running. Pierre Gy developed the most generally accepted sampling theory. One of the main principles is that all particles in a one-dimensional process stream should have equal chances of being included into the sample. A correctly designed and operated transversing cutter comes close to this goal but has limitations in temporal representativity. For slurries an acceptable solution in many cases is to use a fixed vertical cutter(s) in a position where the slurry is well-mixed by turbulence and other means. For online analysis, reliability problems are mostly related to faulty design or installation of the piping system to the analyser. Properties of material processed, process flow sheet and piping details before and after the sampler have to be taken into account when deciding on which sampling arrangement is appropriate. Guidelines and some solutions to these issues are presented in this paper.

Mar 1, 2010

By K Ehrig

You are a geologist, geometallurgist, or metallurgist/process engineer and are fortunate enough to work for an organisation who asks you to design/execute a geometallurgy program. What seems like a simple request is actually not a trivial exercise. æRecipeÆ style manuals are not readily available. However, many æexpertsÆ are lurking around willing to deliver solutions which will solve all of your problems. Even though similar ore deposit styles (e.g. porphyry Cu, IOCG, Ni-laterites, calcrete hosted U, etc.) have many similar characteristics, each ore deposit is unique. Hence your geometallurgy program needs to be æfit-for-purposeÆ. This paper offers some insights gained via designing and executing geometallurgy programs from exploration through to production, and working at a mine where you are held accountable for your metallurgical performance predictors.CITATION:Ehrig, K, 2013. Geometallurgy - What do you really need to know from exploration through to production?, in Proceedings MetPlant 2013 , pp 28-33 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By G D. Matthews, M E. Haylett, S Khosrowshahi, A Weeks

In narrow orebodies the use of ordinary kriging (OK) may pose certain limitations when used for grade control modelling. The smoothing effect of kriging, by its very nature, cannot retain or accurately characterise the dispersion (variability) that is inherent in gold deposits. This dispersion is a critical component of determining the desired level of ore loss and dilution.Fixed block model positions used in OK, and all estimation approaches, within a grade control process may never align with the ‘true’ ore boundary. This may lead to excessive ore loss and dilution, especially within narrow lodes.Using a risk-based approach to ore block design based on the geostatistical method of conditional simulation (CS) can highlight the differences achieved when an alternative method to OK is used for grade control modelling. By using a mesh of nodes and the application of a ‘transfer function’ to the simulation models, the position for ore contacts can be better assessed than when using fixed blocks in OK. Therefore, the value of various ore block boundaries can be better analysed by objective assessment of ore loss and dilution for a given minimum mining selectivity (selective mining unit or SMU), even in narrow lodes.A case study of a narrow vein gold deposit, comparing the results from an OK model and a CS model shows that whilst both models show similar trends – waste, low-grade, and high-grade regions are the same in both cases – the simulation model can provide greater insight for optimal definition of the mineralisation boundary.CITATION:Haylett, M E, Weeks, A, Matthews, G D and Khosrowshahi, S, 2014. Ore block design in narrow vein gold deposits – estimate or simulate?, in Proceedings Ninth International Mining Geology Conference 2014 , pp 421–424 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By D R. Anstey

The mining of magnetite iron ore in Western Australia will generate large volumes of waste rock and tailings over many decades. The need to dispose of these materials will result in massive waste landforms that will require significant planning and management. The formation of comparable man-made landforms is relatively common, as exemplified through past practice in gold and iron ore (haematite) mining. Unfortunately, the performance of these landforms, with respect to long-term stability (erosion resistance), the release of low pH seepage water and aesthetic impact, has commonly been disappointing and environmental legacies have been created as a result. Lessons that have been learnt from past, large mining operations indicate that there is a need to rethink the methods of waste disposal and landform development applied to magnetite mining. The environmental compliance criteria applied to magnetite mines for the storage of tailings and waste typically include minimising dust generation (particularly as the tailings and mine waste may contain asbestiform minerals), control of silt, minimising visual intrusion and management of potentially acid forming materials. In addition, the climate of Western Australia and the paucity of both surface and groundwater in the vicinity of the magnetite mines frequently necessitate water consumption to be minimised. This paper discusses the potential to co-mingle magnetite mining waste streams in a variety of ways to concomitantly satisfy the environmental compliance criteria and the operational requirements of the mine. These methods include co-mingling of coarse tailings and waste through dry-stacking, deposition of tailings as a paste, co-disposing of all wastes to form an integrated landform and the co-mingling of all waste streams to produce PasteRockTM (a blend of tailings paste and crushed waste rock). The paper demonstrates how these techniques can be applied to the magnetite mining industry to provide better outcomes than might be achieved using more conventional techniques, currently employed in large-scale mining operations.

Jan 1, 2009

By K Peters, C McKenzie

New Zealand has an established history of gold production beginning with the gold rushes of the 19th century in the Coromandel, Nelson/Marlborough, West Coast and Otago regions. Despite this, the number of significant modern hard rock gold operations has been limited in recent years due to a lack of sustained exploration capital and not limited geological prospectivity.The New Zealand Government is actively encouraging explorers to invest in New Zealand through a series of targeted promotional visits, more importantly through the acquisition of precompetitive regional geophysical data. Data collection has been completed over the prospective Northland epithermal district and a large portion of the South IslandÆs west coast that is prospective for both orogenic gold and intrusive related gold.Analysis of new data has been an important component in aiding the generation of exploration targets from prospectivity modelling. Determining the prospectivity of an area involves reviewing all the available data and analysing it with respect to the most up-to-date mineral system model for the mineralisation style of interest. Using the weights of evidence modelling approach, the most prospective areas for epithermal gold-silver, orogenic gold and intrusion-related gold have been identified. The key exploration parameters relevant to each mineral system are first represented spatially and then statistically combined into a single prospectivity map. New potentially economic deposits could be found by focusing exploration on targets identified from these models. The prospectivity modelling approach can greatly reduce the risk involved in mineral exploration.CITATION:Peters, K and McKenzie, C, 2013. New Zealand gold potential - using mineral prospectivity modelling to evaluate gold-bearing mineral systems in an underexplored country, in Proceedings World Gold 2013 , pp 479-486 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By D La Rosa, D Bennett

"Exploration drill core provides for a number of standard measurements essential for determining the viability of a new mine or the extension of an existing one. Rock lithology and alteration can be visually determined and grade measured from the half core. Geotechnical parameters such as rock strength and structure can also be measured. Using suitable proxies, these metrics can then be used to estimate run-of-mine (ROM) particle size. In combination with comminution test results, these can subsequently be used to design comminution circuit configurations and estimate their performance.The Frieda River Project drill core for the large Horse-Ivaal-Trukai copper-gold porphyry deposit was unusual due to a late stage gypsum-anhydrite stockwork event that overprinted much of the deposit. Above the base of the oxidised zone, which closely matches the water table, gypsum and anhydrite has been leached out, effectively removing the glue holding the rock mass together. As a result, much of the rock above this gypsum-anhydrite surface is fragmented and gravel-like in texture, while the material below this horizon is typically uniform and competent.Large volumes of the orebody above the gypsum-anhydrite surface are expected to need minimal or no blasting for efficient excavation. In addition, the fragmented nature of much of the material was expected to reduce comminution specific energy as it already appears as though it has been crushed. While this was expected to have positive impacts to the operation, the lack of standard geological logging methods available to accurately define the degree of in situ fragmentation led to difficulty in gaining certainty over the ROM product and grinding circuit feed size distributions.Using the extensive library of core photos for the project, a novel method using image analysis techniques to take both the intact core and gravel into account to predict ROM fragmentation was developed. In addition, existing point load test data was used to infer the strength of the rock and its impact on the blasting, crushing and grinding processes. The novel approach allowed development of ROM size distribution data and improved certainty in the results of comminution circuit designs.This paper describes the methodology undertaken in detail, and discusses the results obtained.CITATION:Bennett, D and La Rosa, D, 2016. The Frieda River Project – a Novel Approach to Analysing Exploration Drill Core: How Broken is Broken?, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 65–76 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

The New Zealand Minerals Industry is small but growing. Over the next 10 years it will be facing stiff international competition for skills to support this growth, particularly from Australia who are forecasting that a further 70 000 people will be employed by 2015.   The value of commodities mined and quarried in NZ continues to increase; and the value of coal, metals and industrial minerals production reached $1.505 billion in 2006, an increase of 15 per cent on 2005. Production increases will continue à. Latest Crown Minerals statistics show that national prospecting and exploration expenditure rose to $29.9 million in the year ended March 31 2006 û an increase of 46 per cent from the $20.4 million spent in the March 2005 year. The equivalent 2001 year expenditure was only $2.48 million.   The industry already experiences difficulty in recruiting the people it needs with ongoing demand for skilled underground miners, trades people, and mining professionals. This discussion paper will outline the national context with regard to labour, skills and training. It will suggest options and provide an opportunity for conference participants to discuss the way forward.

Jan 1, 2007