Search Documents

By Y H. Zhu, X X. Tang, Y C. Yin, M L. Xing

Based on the stiffness theory, the stiffness difference and energy supply of surrounding rocks are important inducing factors for strain burst. However, due to the lack of multi-level low stiffness testing machine, there are few experimental studies on rock failure mechanisms under the influence of loading stiffness. This paper introduced a self-developed rock testing system with changeable stiffness. The main testing machine of this system is a combined structure of inner and outer frame. The change in the loading stiffness is achieved by using a stiffness servo control system to control the energy accumulation in the inner frame. The tests of the sandstone specimens under three different loading stiffnesses in the testing system showed that the loading stiffness did not significantly affect either the uniaxial compressive strength or the Young’s modulus of the rock. However, the post-peak stress-strain curve of the rock became smoother and steeper when the loading stiffness was decreased, and the stress drop rate increased. It is shown that the stress drop rate had a power function correlation with the loading stiffness. After the peak load, the inner frame of the testing system rebounded several times at high speeds. The magnitude of the instantaneous rebound speed and the rebound duration increased with the decrease of loading stiffness. Both the mean rebound velocity and the total rebound deformation had power function correlations with the loading stiffness. The loading stiffness has limited effect on the energy storage and energy dissipation characteristics of the specimen, while the released energy of the testing machine increases as the loading stiffness decreases, which is the key factor affecting the failure mode of the specimen. According to the test results, a rock burst mechanical model considering the stiffness is established, and the energy supply mechanism of rock burst is quantitatively explained.

Nov 29, 2022

By A Crosky, S Saydam, H Chen, H L. Ramandi

Cable bolts and rock bolts are used as primary and secondary anchoring systems in many underground mines. Reports on the premature failure of cable bolts and rock bolts due to stress corrosion cracking (SCC) in underground coalmines have been increasing in the past two decades. The previous studies found that the SCC in both rock bolts and cable bolts occur as a consequence of atomic hydrogen diffusion into the material, which is known as hydrogen-induced stress corrosion cracking, HISCC (Craig et al, 2016; Wu et al, 2018b). While research to understand the process of SCC occurrence in underground mines is still required, finding a prevention solution to protect the bolts from HISCC is crucial. In this study, we analyse a variety of commercially available coatings for steel corrosion prevention, including barrier coating (ie epoxy, polyester TGIC) and sacrificial coating (hot-dip galvanising). We test the coating on coupons manufactured from rock bolts and cable bolts used in the coal mining industry.

Nov 29, 2022

By B Vorster, T Medhurst, A Huey

Roof conditions at Oaky North Mine can be prone to stress related damage and/or time dependent degradation. The ability to identify these areas prior to mining has proved challenging using traditional methods. To help alleviate this situation, a study was initiated to investigate methods for roof characterisation using geophysical logs. This involved the use of neutron log data to provide an indirect measure of the proportion of carbonaceous/micaceous laminae present in the immediate roof strata. Detailed analysis of the shale–porosity inter-relationships arising from this analysis provided a means to estimate the proportion of laminations for a given roof interval. This paper outlines the process and how it was used to improve the current GSR modelling and hazard mapping process.

Nov 29, 2022

By W Zhu, J H. Zhao, H Ma

The permeability coefficient is an essential parameter for the study of seepage flow in fractured rock mass. This paper discusses the feasibility and application value of using readily available RQD (rock quality index) data to estimate mine water inflow and grouting quantity. Firstly, the influence of different fracture frequencies on permeability in a unit area was explored by combining numerical simulation and experiment, and the relationship between fracture frequencies and pressure and flow velocity at the monitoring point in fractured rock mass was obtained. Then, the stochastic function generation program was used to establish the flow analysis model in fractured rock mass to explore the relationship between flow velocity, pressure and analyse the universal law between fracture frequency and permeability. The concepts of fracture width and connectivity are introduced to modify the permeability calculation formula and grouting formula. Finally, based on the on-site grouting water control case study, the rock mass quality index is used to estimate the mine water inflow and the grouting quantity. The results show that it is feasible to estimate the fracture frequency and then calculate the permeability coefficient by RQD. The relationship between fracture frequency and RQD and the relationship between structure surface frequency and permeability follow an exponential function. The calculation results are in good agreement with the field monitoring results, which verifies the rationality of the calculation method. The relationship between the rock mass RQD index and the rock mass permeability established in this paper can be used to invert the mechanical parameters of the rock mass or to evaluate the permeability and safety of the rock mass, which is of great significance to the prediction of mine water inflow and the safety evaluation of water inrush disaster management.

Nov 29, 2022

By C Zhang, G Si, J Oh, X Zhu

The presence of rock joints has a huge impact on the strength, deformability, and permeability of fractured rock masses by providing surfaces of weakness on which further deformation are more prone to occur, and by serving as the major channels of water flow due to low matrix permeability. In earlier studies, water flow-through rock joints is often assumed as laminar flow between two ideal smooth parallel plates, and the well-known cubic law was derived and widely used to characterise the hydraulic behaviour of rock joints. However, natural rock fractures are irregular and of spatially varied aperture. Thus, the concept of equivalent hydraulic aperture was introduced to modify the cubic law. Numerous works have been conducted on the relation between hydraulic aperture and mechanical aperture incorporating various geometrical parameters. The surface roughness is one of the most sensitive factors for water flow-through rock joints. The aperture distributions are irregular in natural roughed fractures relative to the parallel plates. Barton et al (1985) and Olsson and Barton (2001) incorporated the joint roughness coefficient JRC in evaluating hydraulic aperture and proposed an empirical equation based on fluid flow tests. However, their equations do not conform to the dimensional consistency. Many other researchers (Zimmerman and Bodvarsson, 1996; Xiong et al, 2011; Li et al, 2019) considered aperture distributions in their equations. But the aperture distributions change during shear was always neglected. The contact of rock joints also has a significant impact on the hydro-mechanical behaviour of rock joint, since fluid tends to flow-through a rough joint along connected channels while bypassing the contact obstacles with tortuosity. Nonetheless, previous research mostly considered joint roughness or aperture changes based on 2D joint profiles, while the contact and tortuosity based on 3D surfaces were often overlooked. Only a few works have been made on quantifying the effect of contact area on flow behaviour (Walsh, 1981; Zimmerman et al, 1992; Zimmerman and Bodvarsson, 1996; Yeo, 2001), and mostly ignored contact area change induced by shearing and the associated impact on flow behaviour. Summarily, the quantification of fracture geometry effects on water flow in single rock joints still needs further investigation, especially when considering coupled shear-flow processes. This paper, therefore, aims to study the impacts of contact area and aperture distributions of the single rock joint on the flow behaviour. The evolutions of contact area and aperture distributions induced by shear are considered. Then, an improved model for estimating the hydraulic aperture with the mechanical aperture incorporating the above factors is developed. Finally, a series of shear and shear-flow tests are conducted on artificial joint samples and the model performance is verified by comparing against the results of experimental tests.

Nov 29, 2022

By R Carstens, L Munsamy, L Prinsloo, C Huang, C Zhang, R Liang, I Canbulat

With recent advances in machine learning, data-based automated decision-making has been proven successful with promising outcomes in many industries. Its application in the mining sector can be ground-breaking; particularly the data-driven analytics that can support decision-making in the mine and consequently enhance mine safety, efficiency and sustainability. However, the current data science applications in the mining industry are mostly noncomprehensive, especially inadequate in evaluations, thus often requiring further study to be potentially beneficial to operations. Furthermore, it was found that existing literature paid limited attention to understanding the role of such techniques. Hence, in this paper we aim to build an end-to-end machine learning powered data-driven framework for intelligent geo-hazard analytics to support decision-making for underground mining data management, where multiple types of data are managed in an integrated database to support the unified machine-learning model. Here we present the framework as data-driven workflow processes, including data gathering, data preparation, data processing and data presentation. In addition, we present an application scenario of the proposed framework, where falls of ground (FoG) is managed with the historical FoG investigation reports, related panel hazard ratings, compliance data and rock mass characteristics. A demonstration can be dynamic forecasting of high-risk areas for FoG based on both spatial and temporal factors, including a 3D data visualisation. Such a scenario shows the potential of the proposed framework to establish connections among various data fields across a diverse category of data. Furthermore, the results offer important insights for ground instability management and can potentially optimise the underground operation flow.

Nov 29, 2022

By P Mikula, B Darlington, J Graham, P Young

In underground mines experiencing dynamic events, there is an ever-present challenge to design and maintain a capable ground support system. One key component of ground support systems is surface support, which serves the essential roles of retaining failed rock and transferring forces generated by surface displacement to rock bolts or other support elements. Observations underground show that in many instances, standard mesh panels alone do not provide sufficient dynamic support to retain substantial bulking failures imposing displacement onto mesh, and in such cases Mesh straps and W-straps may be employed. Determining the performance of surface support elements proves to be difficult, with a multitude of variables at play in the underground environment. Quite comprehensive work has been completed on laboratory testing of surface support systems; however, very little work has been conducted on in situ dynamic testing of Mesh straps and W-straps. In 2019 in Western Area’s Flying Fox Mine, in situ dynamic testing was conducted on a series of Mesh straps and W-straps using Sandvik’s in situ Dynamic Test Rig (DTR). The testing regime applied impact energies from 5.1 to 15.3 kJ to Mesh straps and W-straps. The performance of the straps that did not fail was a maximum absorbed energy of 9.3 kJ and 14.2 kJ for the Mesh straps and W-straps respectively. The testing successfully demonstrated the ability of Sandvik’s DTR to test not only rock bolts, but also surface support elements, creating new testing and research possibilities. The testing also provided important design guidance data that is not practicable to obtain using laboratory dynamic testing facilities.

Nov 29, 2022

By T M. Nester, D J. Reardon, A N. Page, B J. Barsanti

The load capacity of a friction bolt has long been regarded as 4 t/m of embedment for ground support design analysis and supported by in situ pull test results. In recent years, the authors have observed lower pull test results or inconsistent results which were rarely sighted in the early 2000s. The lower pull test results indicated in some cases that reliable friction bolt capacity (≥90 per cent of results) is closer to 3 t/m of embedment with some geotechnical engineers adjusting the ground support parameters in the design work accordingly. This can be in contrast with other mines which reliably obtain 4 t/m (or greater) using the same suppliers bolt in similar ground conditions. This raised several questions: • What is the effect of poor installation (bolt twist or bolt hole deviation)? • Does the performance of friction bolts vary in different rock masses? • Does bolt performance vary between suppliers? • What effect does increased jumbo feed/percussion/rotation settings have? • Have the bolt dimensions or steel strip width changed? • Have the physical bolt properties changed? • Have the steel properties changed? This paper was aimed to answer as many of these questions as possible and discuss each variable in detail. This project included friction bolt trials at various mine sites across Australia, multiple friction bolt manufacturers, steel manufacturers and laboratory analysis. The paper also includes discussion on what the authors consider best practice for pull testing. It should be noted, the terms ‘friction stabiliser’ and ‘split set’ used in this paper are used in a generic manner and is not linked to any specific ground support supplier. Whilst its acknowledged within the industry the term split set and friction stabiliser is used interchangeably, the authors acknowledge that the term split set is a trademark of Split Set Mining Systems and has been used in context in this paper.

Nov 29, 2022

By Ö Aydan

Rock dynamics is one of the most important topics in the field of rock mechanics and rock engineering. The spectrum of rock dynamics is very wide and it includes the failure of rocks, rock masses and rock engineering structures such as rock bursting, spalling, popping, collapse, toppling, sliding, blasting, non-destructive testing, geophysical explorations, science and engineering of rocks, earthquakes, and impacts. Undoubtedly, the rock dynamics issues in Mars would remain to be the same. Although mankind has no direct access to Mars yet, the Mars exploration rovers (Opportunity, Sprit, Curiosity and Perseverance), Mars Reconnaissance Orbiter and InSight Lander provided very valuable data so that some rock dynamics issues can be recognised. The author reports his considerations on rock dynamics issues in Mars from very careful examination of images and data provided from MERs and MRO and discusses their implications.

Nov 29, 2022

By I Gray

Other than being reasonably certain of the average vertical stress being lithostatic, there can be little certainty about stress in the ground. The stresses and strains in rock are a function of gravitational effects, external load, thermal changes, diagenesis and their mechanical properties including elastic, creep and post failure behaviours. It is highly desirable to measure stress where mining is going to take place, even if the virgin stress condition has already been changed by mining. The concept of some far field stress value that is more or less constant is usually invalid and can be dangerous to use in mine design. Measuring stress is not simple. The basic processes are broken into two categories, one where the rock will not fail around the borehole in which the stress is being measured and one where the rock has failed or will fail. Because of the complexity and cost in obtaining a single, precise stress measurement it is highly desirable to have some system to be able to obtain an idea of the uniformity, or otherwise of the stress situation between precise measurements. Table 1 shows the methods for measuring stress. The first five methods work on the basis of some fairly direct measurement of mechanical rock behaviour while the last three are attempts to get some idea of stress out of core long after it is removed from the host rock. While these latter methods appear to tick all the boxes for applicability there is a great deal of uncertainty in the results that they deliver. This paper reviews the methods for measuring stress and presents two new methods. These are a three dimensional overcore system to provide precise stress measurements in rocks that will not fail around the borehole and a core ovality system. The latter can be used to provide information on the stress difference orthogonal to the core. It is particularly useful because it can be used every metre of core length.

Nov 29, 2022

By R deMoraes, A Bobet

The last decade has seen a resurgence of interest in lunar exploration and the emergence of countries like China and India as space fairing nations. In 2004, the US announced a new Vision for Space Exploration, whose objectives focused on human missions to the Moon and then Mars. The near future is likely to see the emergence of a worldwide drive to revisit the Moon as the first step in investigating the Solar System. To date, the Apollo missions provide our only experience of human operations on the Moon or anywhere else beyond Low Earth Orbit. Much was learned from these missions. However, their short duration means that many of the environmental effects that will be important for longer-duration missions could not be quantified. In addition, long-duration missions and infrastructure on the Moon require new technologies and capabilities, which must operate successfully and reliably in this lunar environment. Developing these technologies poses significant challenges for the exploration program. The paper discusses the risks associated with the construction of lunar surface and underground structures and the challenges to adopting the standards and rock mass classification systems developed on Earth and their applicability to the Moon. Moreover, an exchange of views to explore near-surface geologic and geotechnical profiles of the Moon is emphasized and implications of the lack of knowledge on rock mass characterisation of the Moonrock mass, the lack of theoretical/empirical experience on the use of rock mass systems outside Earth, and uncertainties.

Nov 29, 2022

By A Sainoki, D Fukuda, K Shioya, C Zhang, M Sharifzadeh, T Yamaguchi, S Saydam, J Kodama, C A. Amagu, Y Fuji

In an open pit mining, ensuring stability of rock slope has been one of the major challenges. As the instability of rock slopes can results in slope failures; consequently, endanger the lives of workers, affect mining operations, and often lead to economic losses. Therefore, it is practical important to study the stability of rock slopes to ensure safe, smooth, and effective mining. The stability of rock slope of about 130 m height at Higashi-shikagoe limestone quarry, which has experienced slope failures four times since 1996, was assessed. The rock mass at the quarry is consists of mainly limestone, schalstein and slate rocks intersected by clay seams of about 70 m thick at footwall of the rock slope. Previously, the effects of limestone excavation at the foot of the rock slope and shear failure due to rainfall infiltration have been investigated. Although clay is widely known to plays a vital role in the stability of slopes in engineering projects including mines, but its impacts on slope deformation at the study quarry are not adequately examined. Therefore, the present study addressed the impact of presence of clay on slope deformation at Higashi-shikagoe limestone quarry by employing both field displacement measurements and numerical simulation. Firstly, surface displacements measured by automated polar system (APS) for over eight years were analysed to understand the overall characteristics of the slope deformation. The measured results show that the displacement gradually decreases with time. The maximum displacement of about 100 mm was observed at middle of the rock slope. Secondly, the effect of deterioration and plastic behaviour of the thick clay layer were simulated using two-dimensional finite element method (2D FEM). The simulated results reveal that the clay exhibited deterioration by water contact and plastic behaviour arising from mining activities at the footwall of the clay zone. Based on the characteristics of the measured and simulated results, it was found that the displacement induced by the effect of deterioration of clay is more noticeable at the north side of the quarry whereas displacement induced by excavation is quite significant at the south side of the quarry if clay behaves as an elasto-plastic material.

Nov 29, 2022

By J Franke, C Gonzalez

One of the regular tasks of geotechnical and mining engineers is the measurement and management of deformation in underground excavations. Although several methods are used to do so, the incumbent methodologies for monitoring deformation and ground support serviceability are limited to the use of visual observations or measurements at discrete points, resulting in a qualitative assessment only. The introduction of LiDAR technology allows a quantitative assessment across the entire excavation volume and its rock surface, by collecting a full three-dimensional image of the entirety of an excavation such as an underground drive, decline, or a tunnel. Comparisons between epochs of complete 3D data coverage allows for change detection over time that doesn’t feature otherwise typical omissions. The implementation of regular scanning has shown to be highly advantageous for mines with swelling or squeezing ground, but also at mines with rapid deformation. Despite the LiDAR potential, its adoption has been slow. A key reason for that is that working with point clouds is foreign to most geotechnical engineers. Point clouds have long been the realm of surveyors, but to fully adopt their use in geomechanics requires retraining, upskilling, and devotion by the individuals and the company. Sites are already stretched, so often there are insufficient resources to be applied to bringing the new technology into use. The solution to this hurdle is to partner with subject matter experts to achieve the desired high-quality outcomes without the commitment of time by geotechnical personnel. This paper presents a new solution of fully automated raw LiDAR point cloud data processing that not only enables geotechnical engineers to avoid having to learn unrelated skills by allowing for deformation monitoring without associated training or expertise, but it also provides instant reporting results as well as a sophisticated database with features otherwise not available. All data processing time and effort is completely replaced by an automated process which at the same time opens up the opportunity to monitor many more excavation volumes at a higher frequency than is possible with conventional tools and methodology.

Nov 29, 2022

By W Y. Guo, L X. Chen, D X. Zhang

To obtain the rock type-I crack propagation process accurately, a novel fixture is used to make the prefabricated crack of rock propagation along the predetermined direction. In this study, the crack propagation process of rock is monitored with the digital image correlation method (DICM), and a mechanical model of crack directional propagation was established. The results show that the simple crack directional propagation device can effectively realise the stable propagation of type-I crack along the predetermined direction, the crack initiation angle is less than 10°, and the deviation between the peak strength of crack propagation calculated by a simplified mechanical model and the tensile strength of Brazilian splitting is 22.76 per cent and 7.53 per cent, respectively. According to the deformation field evolution law, crack propagation can be divided into three stages: microcrack development, main crack propagation, and main crack propagation. As for the rock type-I crack initiation and propagation mechanism, before reaching the peak strength, the prefabricated crack tip is subjected to maximum tensile stress; the elastic energy increases rapidly, and the dissipation energy increases slowly; after the peak strength, elastic energy exceeds its energy storage limit and released rapidly, and most of the input energy is converted into dissipation energy, which makes the crack propagation rapidly. The crack directional propagation device will be further optimised and improved, and it is expected to provide a new method for the study of crack propagation mechanism, rock failure precursor information and crack arrest principle, etc. It will also provide theoretical references for the optimisation of coal strata directional blasting, fracturing, fracture arrest, and other related technologies in geotechnical engineering.

Nov 29, 2022

By S J. Chen, N Jiang, Y S. Ding, F X. Li, D W. Yin, F Wang

This study assessed the deformation failure characteristics of rock-coal composites with different height ratios. Uniaxial compression tests were conducted using an acoustic emission monitoring system and XTDIC three-dimensional full-field strain measurement system. The results showed that with the increase in rock-coal height ratios, the uniaxial compressive strength of composite samples increased from 5.26 MPa to 14.61 MPa. The evolution of the deformation localisation zone of the composite samples is closely related to the initiation and propagation of the primary cracks in the coal samples. At the moment when the main fracture of the coal samples occurs, there is a large drop after the peak of the stress-strain curve of the composite samples, and the height of the rock samples increased to varying degrees, which indicated that the failure of the coal samples induced the rebound deformation of the rock samples. With the increase in rock-coal height ratios, the rebound deformation amount of the rock samples decreased from 0.042 mm to 0.008 mm, and the rebound deformation rate decreased from 0.210 per cent to 0.010 per cent. Meanwhile, the rock samples’ rebound deformation releases part of the elastic energy to act on the coal sample, further contributing to the destruction of the coal samples. Compared with single composite coal samples, the coal samples of the composite samples have much more failures. In addition, with the increase in rock-coal height ratio, the input energy density, elastic energy density, post-peak release energy density, and residual elastic energy density of the composite samples increased, the dissipation energy density decreased, and the percentage of pre-peak elastic energy density increased from 98.56 per cent to 99.86 per cent. These results revealed the deformation failure characteristics of rock-coal composite with different height ratios and provided a theoretical reference for understanding the underground dynamic rock failures.

Nov 29, 2022

By I Canbulat, G Si, Y Duan, X Luo

The presence of unfavourable geological structures such as faults and dykes often can contribute to coal burst risk. Seismic events associated with rock fractures tend to cluster around these structures and it is important to understand the characteristics of seismicity for coal burst risk management. In an Australian underground longwall coalmine, two clusters of seismic activities close to the longwall face and within a section of the maingate roadway which was intersected by a major dyke were respectively identified. The induced seismicity in the dyke-roadway area was closely related to the longwall mining. These seismic events were located and the distribution of seismic events shows that more fractures were distributed on the inbye side of the dyke. The spatial-temporal changes of the seismic event locations delineate the fracture propagation as the longwall mined through the dyke. The frequency-magnitude relationship of seismicity was analysed and it was found that it changed significantly when the longwall was mining towards, through and past the dyke. The monitoring results demonstrate that because of the stiff dyke, the seismicity was intensified in the roadway section. It proves that the dyke promoted stress re-distribution and seismicity in its vicinity. More fractures were induced in the hanging wall of the dyke, whereas less strain energy was accumulated and released in the footwall of the dyke.

Nov 29, 2022

By N Power, R Hassell, E Jones

Wiluna Mining Corporation are progressively re-entering the old Wiluna underground mining complex. The existing underground was abandoned in 2013 by previous owners and left to flood with water levels reaching above the East Pit portal and Happy Jack Pit portal and up to 300 m below surface in the Bulletin underground. Re-entering the mine commenced in 2017 with dewatering of the Bulletin decline. The underground development had been previously supported with friction bolts, with weld mesh in places. Until mid-2021 rehabilitation requirements were based on an external visual inspection of the installed ground support scheme. However, several incidents involving falls of ground due to corroded bolts have occurred during this time, showing that this approach was inadequate. The challenge the operation faced was should the entire decline be rehabilitated, the implication being not only a large rehabilitation cost but also the impact of severe delays to the mining schedule. The question was asked can the operation better understand the level of corrosion damage and potentially optimise rehabilitation requirements. A proposal to use a systematic approach to assess corrosion by environmental condition mapping, visual external corrosion assessment, and internal corrosion assessment via borehole camera inspections was provided and accepted by Wiluna Mining Corporation. The objective of this work was to produce a three-dimensional map showing the degree of corrosion on the reinforcement systems in the capital infrastructure, this would then be used to risk assess and prioritise rehabilitation requirements. This paper summarises the approach, methodology and results that provided the Wiluna mine planning team with information to enable planning of resources and budget to justify priorities of rehabilitation.

Nov 29, 2022

By M Zoorabadi, Y Zhang, D Bringemeier, S Nicoll, N Kerr

Lihir operations of Newcrest Mining Limited (NML) are on Lihir Island (PNG) which is located approximately 900 km north-north-east of the national capital Port Moresby. The mine is located within the Luise Caldera of the Luise Volcano which is located on the east coast of the island. The caldera is an extinct volcanic crater that is geothermally active. Volcanic activity on Lihir Island is limited to remnant hydrothermal venting in the Luise Caldera in the form of hot springs and fumaroles. Steam and gas (including H2S) naturally discharge within the pit area and along the Kapit beach and near shore region. The hydrothermal reservoir temperatures can reach 100°C at the water table and exceed 200°C at depth. Newcrest maintains a Geo-hazard Management Plan to identify and manage the various geotechnical and geothermal hazards on-site. The major geothermal hazard to mining at Lihir is the occurrence of geothermal outbursts, which have occurred in the past with varying intensities and caused two ‘near misses’, production delays and material losses.

Nov 29, 2022

By C G. Sweeney

The underground mining industry is seeing unprecedented shortages in skilled labour. Migration to Australia being at an all-time low is a leading concern, with pandemic-induced border closures and lockdowns only exacerbating the skills shortage, not causing it. The skills shortage is forecast to peak in 2023 and remain high beyond 2025. With this skills shortage in mind, mining companies throughout Australia are trying to deal with stricter protocols around Health and Safety (H&S) legislation, as well as more stringent controls on quality assurance, particularly as underground mines are reaching greater depths and extending into ‘unchartered territory’. The cumulation of this is proving to be a major hurdle in ‘effective’ operational geotechnical management. The drive for automation in mining is bringing another level of complexity. However, ‘once automation is up and running, it presents the opportunity to access talent pools that may not normally be available. There is also a change in skillset that will be required to drive automation. ‘The top two emerging roles that will be critical for the future of the mining industry are artificial intelligence and machine learning (AI/ML) specialists, and process-automation specialists’ (Writer, 2021). If anything positive has come from the pandemic, it has shown that remote working can be effective and that the drive for automation and critical evaluation of skills required on-site should be given greater priority. UQ acknowledges that the industry is changing, and that digital technology is required to be offered in mining related disciplines. Industry and academia need to do more to promote geotechnical engineering in mining and balance the curriculum to suit the future of mining and make it more enticing. The average cost of a geotechnical failure is about $5 million in coalmines and can be into the hundreds of millions of dollars if production is affected (Cartledge Mining and Geotechnics, 2020). The cost of a good geotechnical design far outweighs the potential losses if a failure were to occur. This alludes to the growing importance of experienced geotechnical consultancies playing a pivotal role in managing mine site geotechnical hazards, while the industry is developing the next generation of geotechnical engineers.

Nov 29, 2022

By K Young, M Martin, D Payne

This paper outlines the evolution of managing high consequence risk scenarios in BHP Coal, with particular focus on managing the stability of an endwall that is adjacent to a public infrastructure corridor running through a Central Queensland coalmine. BHP Coal developed a Geotechnical Consequence Register after industry failures identified shortcomings in traditional risk assessment practices. Traditional risk assessments consider the consequence and likelihood of a geotechnical event occurring under normal operational conditions. As such, the risk rating for a high consequence, low likelihood failure may fall within the acceptable range, even where a lack of meaningful geological data exists due to the area being off lease or outside of mining reserves. The Geotechnical Consequence Register lists all geotechnical failure scenarios of high consequence, identifies if current controls are adequate, and highlights if specific Geotechnical Management Plans are required. This case study reviews a failure scenario that was identified through the geotechnical consequence register. The scenario had previously been considered low likelihood and subsequently driving a low risk; however, the likelihood ranking was impacted by a lack of geological data outside of the mining lease and predominately informed by an acceptable historical slope behaviour. Additional exploration identified previously unmapped faulting which increased the risk rating. The requirement to develop a specific management plan resulted in an increase in the required factor of safety, design changes, the implementation of additional monitoring and a corresponding monitoring Trigger Action Response Plans (TARP). In the case study area, the initiation of a geotechnical instability was identified early through the increased monitoring program. The instability was successfully managed and any impact to the infrastructure corridor off lease was prevented. BHP Coal has used the Geotechnical Consequence Register for several years to identify and assess high consequence geotechnical failure scenarios. In some areas this has justified additional exploration, more stringent design acceptance criteria and an increased level of geotechnical monitoring. The process has been successful in ensuring that geotechnical risk is controlled in areas that often receive less attention than active production areas.

Nov 29, 2022