Search Documents

By Ruschitzka C

The productivity and economic success of a German hard coal mine is attributed to the high productivity of a small number of operation points; however high rates of production are associated with increased gas emission at the working sites. Therefore modem high technology is required in order to reach the planned production rate, since high methane concentrations often cause unplanned breakdowns in operation. The optimised simulation of gas emission is a fundamental planning tool for mine design as well as for determining the potential of a coal deposit and has increased in significance over the last years. Methane-INFO enables the three-dimensional, graphical simulation of a working site taking account of different aspects such as the mine design, ventilation, production rate, geology, seam quality, gas exhaustion, etc. The following paper gives a short overview over the benefits of the discussed system.

Jan 1, 1995

By Mauk JL, Arehart GB, Mathews SJ

The banded nature of the quartz veins which form the Empire lode at the Golden Cross mine, is perhaps their most striking feature. Petrographic studies show that significant differences occur between the bands in terms of textures, quartz grain size, calcite, adularia and kaolinite content, and the form, concentration and mineralogy of sulfide phases. The 818Oqu i values of individual bands within the vein material range from 7.3-10.9%x. Calculations show that the 818Oqäa,u values can be adequately explained by temporal variations in the system temperature, boiling and/or variations in the systems fluid/rock ratios.

Jan 1, 1995

By Sandvik

Fine grinding in an air-swept ball mill working in closed circuit with a forced vortex air classifier has been investigated first in continuous laboratory and then in industrial scale. Results from the laboratory circuit have shown significant influence of mill load (powder filling) on the capacity of the circuit. In laboratory scale the mill load was measured and controlled by a weighing platform placed under the complete mill set-up. The mill load of the industrial air-swept ball mill has till now been controlled by measuring the power consumption of the mill motor. Thus, it was necessary to operate far from the range of optimal mill filling. To improve the circuit performance, alternative ways of mill load measurement were investigated. An important factor was investment cost, as many fine grinding mills operate in relatively small circuits that do not wan-ant large investment. In this case the task was accomplished by using a piezoelectric strain transducer, which detected strain changes in the mill shell. It was installed in the midpoint of the shell, where the highest deformation was obtained. As the transducer was on the top position, it indicated compression, and on the bottom position it measured tension. By taking the difference between the readings, it was possible to calculate total strain variations, directly proportional to the mill load. The signal from the transducer was sent to a control room via a cordless infrared communication system, employing a microprocessor control card, which could further regulate other operating parameters of the circuit according to the software model. The installation required very low investment cost and provided simplicity of application as well as stability and reliability of characteristics under severe industrial condition. The measurement system made it possible to optimise the mill load and thus increase the production from 3.2 to 3.7 dh (15 per cent), and stabilise the circuit operation.

Jan 1, 1995

By Heath E, van Calsteren P, Turner S, McDermott F

U-Th isotope studies of recent volcanic rocks may be used to evaluate the depths and rates of melt generation beneath mid- ocean ridges and ocean islands. Island arc rocks exhibit a similar range in Th isotopes to that seen in both MORB and OIB, but while those with high (230Th/232Th) tend to have excess 238U, many of those with low (230Th/232Th) are in isotope equilibrium. The excess 238U is attributed to the preferential mobilisation of U in hydrous fluids from the subducted slab within the last 100,000 years, whereas the low Th isotope ratios in the higher-K arcs are primarily due to the introduction of subducted sediment. Preliminary results from mineral separates from lavas on Soufriere on the island of St. Vincent indicate that some of the minerals crystallised up to 50,000 years prior to eruption.

Jan 1, 1995

Interaction between rock and fluid plays a critical role in rock engineering ventures such as stimulation of oil and gas wells, geothermal energy recovery and nuclear waste isolation. Robust and reliable design of the related services and underground facilities is based on understanding of the mechanics and chemistry of the coupled hydromechanical- thermochemical processes. This paper explores the application of the theory of such processes in minerals engineering, with particular reference to rockburst mitigation, in situ solution mining and cavity completion of coal-bed methane production wells.

Jan 1, 1995

By Meyer T

Sunburst PCF (Penetrating Cone Fracture) technology has recently undergone extensive underground field trials at Leinster Nickel Operations, Western Australia. Trials with the Sunburst machine started in September 1994 and continued through to December 1994 during which approximately 130 metres of tunnel were developed. The Sunburst technology was used to excavate sub-levels through ultramafic nickel ore for future sub-level caving operations at the Perseverance nickel mine. The Sunburst machine demonstrated reasonable instantaneous advance rates, however, there are still a number of future developments/design changes which need to be addressed prior to the PCF technology being trialed again in a production environment. This paper benchmarks conventional drill and blast at Leinster against the Sunburst Excavator machine performance within similar tunnel dimensions and rock conditions. In addition to productivity and cost information; environmental considerations, support and labour requirements are also discussed. Problems with the current machine design are highlighted and possible future design changes are suggested. The Sunburst machine could be a suitable technology for advancing development through weak to moderate rock conditions and may also reduce overall support costs. With the potential for automation and the ability to reduce rock damage into the development tunnel walls, it is proposed that the Sunburst machine warrants further consideration.

Jan 1, 1995

Renison Goldfields is one of Australia's largest mining companies with annual sales revenue over $600 million. It has ten operating mines and processing plants, with operations in most States of Australia and in Papua New Guinea, Indonesia and the United States. The exploration division is active in,other parts of the world, including Europe and South America. RGC produces gold, copper, tin, coal and mineral sands. RGC is typical of companies in the mining industry in that by contrast to the typical pattern in other industries, it is necessary to have systems to handle a variety of different types of operations, a range of size of operations, and operations in remote locations.

Jan 1, 1995

A vital ingredient in ensuring that metals exploration companies, working in the developing countries of the Pacific Rim, support the development of national geologists is making such a learning program cost-effective. There is a wide spectrum of learning needed in the development of these explorationists: the technical and conceptual skills to carry out exploration efficiently, the professional and managerial skills to apply the exploration in the work situation, the personal attributes required to manage their exploration effectively, and a company organisation that allows them to learn and use these skills and attributes.

Jan 1, 1995

The increased focus on best practice environmental management has led to mining and mineral processing companies developing a variety of procedures to ensure that the environmental impacts of their operations are minimised, and that company managements are fully aware of these impacts and the policies and procedures established to ensure this process. Parallel to this, international standards for the development and implementation of environmental management systems are being promoted as necessary for companies to demonstrate their due diligence. Good environmental management systems should be built upon the systems already established within companies, and should ensure that the process of continual improvement is integral to their operation. An outline of the basic components of environmental management systems is provided, along with examples of the way various mining companies have implemented such systems. The benefits of best practice environmental management to mining companies are also considered.

Jan 1, 1995

By Simmons SF, Fleming J

Alteration and mineralisation at the Island Copper deposit is related to the intrusion of Early Jurassic quartz feldspar porphyry dykes into surrounding comagmatic Bonanza volcanic rocks. The pyrophyllite alteration zone forms an upward flaring cone, largely hosted within a breccia body that c ross-cuts the Cu, Mo, and Au-rich ore shell. This alteration zone contains pyrophyllite, dumortierite and diaspore and resembles alteration occurring in some high-sulfidation deposits, but which is barren. Fluid mineral equilibria and fluid inclusion studies indicate formation at approximately 300 ¦C from fluids dominated by steam and gases. These fluids appear highly acidic, but sulfur poor, leading to extreme base leaching within the breccia body and surrounding rocks.

Jan 1, 1995

By Bhattacharyya A. K

A major constraint on sustaining high rates of production in the collieries of the Southern Coalfield of New South Wales is the inability to develop panels fast enough to match the rates of extraction. This inability is particularly crippling in the case of retreat longwall mining and is due to nearly half the time in roadway drivage being spent on strata control operations such as roof support.Increased rates of roadway drivage and significantly improved roadway stability can be achieved by the application of yield pillars between parallel roadways. These pillars are designed to yield immediately upon formation and transfer the damaging roof loads away from the immediate vicinity of the roadways. Since the width of the yield pillar is the key to their successful application, it was determined through the Yield Pillar Experiment conducted by Kembla Coal and Coke Pty Ltd at West Cliff Colliery.Three experimental headings, each nominally 5.5 m wide and 2.8 m high, were driven to form two tapering pillars. The width of these pillars progressively decreased from 24 m to 3 m over a length of 154 m. The convergence between the roof and floor of the headings measured at various cross-sections corresponding to predetermined widths of the pillars are analysed in this paper to evaluate the stability of the tapering pillars at the different widths.The width of the yield pillar in a three heading development layout at West Cliff Colliery was determined to be 7.5 m.

Jan 1, 1995

By Prakash AJ, Singh PK, Dhar BB

Safety and stability of underground mine openings, coal pillars and water dams in the near vicinity of operating surface mines are endangered from excessive blast induced vibrations. This paper deals with the investigations carried out in four coal mines. Simultaneous measurements at equal distances from the source indicated higher level of vibration on the surface than those produced in the underground workings. The values of peak particle velocity (PPV) measured on coal pillars, body of water dam were lower than those measured on roof and junctions of the roadways. The parting of coal (3-4.5 m) between two sections vibrated with higher PPV compared to the roof of top section and floor of bottom section. In one case the influence of total charge fired in a round was significant in generation of vibration compared to the maximum charge/delay where monitoring was done vertically below the source.

Jan 1, 1995

In recent years a number of explosive blends including ANFO, emulsion and watergel products have been used in a variety of ground types and applications. These `standard' explosives' technologies are not new, but out of the uses and applications, have sprung a new generation of tailored explosives that match the ground type and the operating environment. This is in stark contrast to the norm, where various patterns and loading configurations have traditionally been designed to accommodate the explosive. This paper discusses these tailored explosives and the explosives' technology behind why they work. Active tailoring of explosive formulations can save mining dollars while essentially leaving the explosive price unchanged. Tailoring explosives may lead to increased rock breakage, heave, digging rates; lower digging maintenance costs and in some cases replacing earth moving machinery altogether. Tailored explosives may have other benefits such as reduced over pressure compared with standard alternatives. The tailoring of explosive performance generally involves three major methods (other than changing the bulk density and sensitivity): (i) replacing fast burning reactants with slower burning reactants or vice versa; or (ii) leaving the explosive intact and diluting the entire explosive with slow burning or `inert' material; or (iii) changing the concentration of the fuel/oxidiser mix. When tailoring explosives for particular applications, authorising, testing, costing, manufacturing, and delivery systems must also be taken into account.

Jan 1, 1995

By Taylor GP

Mining Lease SML 57 was registered to Mount Kasi on 5 January, 1995. The Mount Kasi gold mine is located in Vanua Levu, Fiji's second largest island and operated from 1932 to 1946 producing 261,000t of ore at an average grade of 7.5g/t Au. The deposit represents a structurally controlled style of high sulphidation copper gold mineralisation with peripheral low sulphidation mesothermal vein type gold mineralisation. The resource consists of 1,048,000 tonnes of residual soils (eluvium) containing 1.9 g/t Au at 0.5 g/t Au cut off and 1,240,000 tonnes of hard rock at 3.0 g/t Au and 1.0 g/t Au cut. 94 drill holes, 298 auger holes and 85 pits were modelled to outline the resource. 29% of the pits bottomed in mineralisation and it is likely the full thickness of eluvium has been understated. The pit is scheduled to produce 500,000 tonnes of ore per annum to yield 35,000 ounces of gold with an initial 2 years of eluvial ore followed by a further 2 years of hard rock ore. Total capital costs are estimated to be less than 10.0 million dollars with construction planned to commence in 1995. The likelihood of locating further ore is high.

Jan 1, 1995

By A B. Christie, R L. Brathwaite, A Swain

This study provides quantitative data on vein distributions within seven selected epithermal systems, four deposits hosted predominantly in rhyolitic rocks: Ohui, Wharekirauponga, Neavesville and Komata, and three major deposits mainly hosted in andesite: Martha Hill, Golden Cross and Karangahake. The technique of fractal analysis was used to help quantify vein distribution patterns. The fractal dimensions (D) obtained are related to the number of veins per metre, the degree of vein clustering, and vein thickness. An increase in any of these tends to increase the fractal dimension.   It is the relative relationship of these parameters that is important for the characterisation of vein distributions, and the comparison of different deposits. Within the same systems, the rhyolites are characterised by lower vein thickness and vein density, but have a higher degree of vein clustering compared to the andesites. Sections that are deeper and more centrally located within the epithermal system and/or close to major structures tend to have a greater degree of vein clustering, higher average vein thickness and density, and higher thickness to density ratios. This depth control is most pronounced in epithermal gold-silver systems because they have formed at shallow crustal levels where physico-chemical conditions change drastically both vertically and laterally. In addition to lithological and structural control at vein scale, deposit scale structure is of great importance in the deposition of economic mineralisation. Large open vein structures capable of sustaining high fluxes of hydrothermal fluid, favourable for the formation of large, high-grade gold deposits, are best developed in andesite sequences.

Jan 1, 1995

The transgressive sedimentary sequence of the Notnnea Basin contains rhyolitic lavas and less voluminous mafic and intermediate volcanims of shoshonitic affinities which erupted simultaneously during the late Cretaceous. The shoshonitic volcanism shows a trend from early inafic to younger evolved intermediate lithologies. The rhyolites are consistently calc- alkaline. There is no evidence of 'mixing, of, the two magma types. The shoshonitic volcanism is the result of a short-lived subduction event related to sprcadime in the New Caledonia Basin and involved reactivation of an earlier Mesozoic subduction zone.

Jan 1, 1995

By Totterdell JM

The Permian-Triassic Bowen Basin and the Jurassic-Cretaceous Surat Basin evolved in a backarc tectonic setting behind an active convergent plate margin in eastern Gondwana. Several extensional (Early Permian; Eocene) and contractional (mid- Permian; Early Triassic; Middle-Late Triassic; early Late Cretaceous) intraplate deformational events are recognised in the basins. These can be correlated with similar events in the New England Orogen that was being deformed in the Late Permian- Late Triassic as a foreland thrust belt. The intraplate deformations were probably the consequence of plate interactions, including the accretion of terranes, at the ancient active plate margin, remnants of which now occur in New Zealand.

Jan 1, 1995

By Baird G. R, Jurak R. N

In this study Dynamic Finite Element Modelling is used to investigate the distribution of peak particle accelerations (PPA) induced in a rock mass by a vertical decked column of explosives. The rock mass is assumed to be viscoelastic. The influence of the delay time between decking charges, the viscosity attenuation (quality factor Q), the decking configuration, and the velocity of detonation (VOD) on PPAs is examined. The results of this paper are relevant to fragmentation since the nature of the fragmentation is related to the stress magnitude and hence the PPAs. It was found that increasing the VOD, and increasing Q increases the PPAs in the neighbourhood of the blasthole. However, the VOD and rock quality factor Q have little influence upon the distribution of PPA. It was also found that an even distribution of PPAs, at a fixed distance from the blasthole, could only be obtained by increasing the ratio of charge length to stemming length. The study showed that the amplitudes and distribution of PPA surrounding the blasthole was approximately independent of the delay time between the decked charges. The modelling also shows that the particle accelerations at locations below the bottom of the charge are relatively small and so the model predicts no substantial damage below the bottom of the charge after blasting.

Jan 1, 1995

By Winrove G. S, Herdie G. J, McCarthy C. A

Production of hot metal from the Hlsmelt Research and Development Facility at Kwinana, Western Australia commenced in October 1993. The stand-alone facility is a unique, coal-based, integrated ironworks equipped to process iron ore fines to pig iron and simultaneously undertake a wide range of research tasks. The data generated will be used to verify the commercial potential of the technology and to set the design and operating parameters for a full-scale production plant. The design, construction, commissioning and initial operation of the HRDF has required many innovative and practical solutions to be developed and implemented by the international group of organisations contributing to the Hlsmelt Project. Initial operation has produced results which demonstrate the potential of the unique process technology associated with the core plant smelting unit. The recent achievement of post-combustion levels of 60 per cent with heat transfer efficiencies greater than 85 per cent demonstrates that the performance obtained with the Small Scale Pilot Plant in Maxhutte, Germany can be reproduced at a larger scale. The results presented in this paper support the thrust for further intensification and future commercialisation of the process.

Jan 1, 1995

Blasting in Norwegian mines is often carried out by contractors who tend to look for the cheapest solution, without concern about fragment quality. The requirementsfor a contractor are usually only related to the maximum size of boulders and the quantity per month. Even when the owners of the mine are responsible for blasting, very little effort is made to optimise the blasting process. This paper presents test methods which were used and results from small-scale and full-scale blasting tests. In the small-scale tests, cubes 500 x 500 x 500 mm of four different rock types were blasted in a chamber, using two types of dynamite explosive. The velocity of detonation (VOD) for the dynamite explosives was 3000 m/s and 6000 m/s respectively. Three cubes of each rock type were blasted with each type of explosive, and a total of six cubes of each rock type was used. The entire muckpile (approximately 350 kg) was- sieved and weighed after each blast and fragments between 8-16 mm were tested for impact values and flakiness. The results of these tests clearly showed improvement in fragmentation the closer the acoustic impedance ratio of the explosive (VOD x density) over the rock (Cp density) was equal to one. The results also showed that the quality of the fragments (in terms of impact values) tends to be better when the cubes are blasted with the high velocity dynamite.

Jan 1, 1995