Search Documents

By R. H. Keyes Duval

"The one point left off the table was pumping costs, i.e. the cost of pumping to the cyclones.At East Malartic 5 x 5 S R L pumps that had been used to pump the classifier overflow were used to pump the rod and ball mill discharges to the cyclones. Maintenance costs on the pumps rose from $105 in 6 months to $1000 per month. The pumps had to be operated at 1150 rpm and impellers lasted only 5 to 6 days. These pumps were replaced by 6 x 6 S R. L. pumps operating at 825 rpm, but at this speed the coarser sands settled and plugged the pipe lines and the speed was increased to 925 rpm. The maintenance cost is now $100 per m::rnth which is 0 003 cents per ton milled. The impellers now last 1 month and the casing linings 6 months.Density meters are often used on cyclone overflows and sometimes on the cyclone feed. Haliburton weighted tube density meters are used in some plants. They are cheaper than the radioactive density controller, $2500 as compared to $ 6000The angle of the discharge spray from the apex can be used to judge the quality of perform1nce of a cyclone.For ordinary metallurgical applications the inside slope of the cyclone is not too important but for fine separation steeper slopes are used.The cyclone is a versatile tool and will handle considerable variations in feed tonnage - probably up to 15%. Above this variation the number of cyclones used has to be increased or decreased or the tonnage fed to them has to be adjusted"

Jan 1, 1965

By S. Downing, T. Grammatikopoulos, N. Hoffmann, C. Gunning

"Most deposits display a high degree of geological and mineralogical complexity that can affect metallurgical processing. Therefore, the proper characterization of the ore and gangue minerals requires a multi disciplinary approach combining geology, mineralogy, geochemistry and processing. However, mineralogy to a large extent informs the metallurgical process. Automated methods can be used throughout the mining chain from advanced exploration through to production.In this presentation we discuss actual case studies where automated mineralogy has been applied in a geometallurgical framework at a pre-feasibility to feasibility level. These include examples from a strongly serpentinized magmatic Ni deposit (Dumont) and a magmatic Cu-Ni deposit (Maturi). Mineral speciation and ratios, e.g., chalcopyrite, cubanite, and pentlandite/pyrrhotite are critical to model the Cu-Ni magmatic deposit. In the serpentinized Ni ore, automated mineralogy is used to speciate the Ni minerals into sulphides, alloys and refractory Ni in the silicate matrix.The mineralogical results are linked to the metallurgical test work in order to model the geometallurgical domains. These case studies will illustrate how mineral quantification and improved understanding of inherent mineralogical parameters in relation to metallurgy reduce technical risk in both exploration and flowsheet development.INTRODUCTIONGeometallurgy is a cross-discipline approach combining geology, metallurgy and mine planning (e.g., Dunham et al., 2011). It is aimed to improve the understanding of geological, mineralogical and metallurgical parameters of an ore. Informational gaps among the different disciplines are often apparent. Automated mineralogy is shown in many studies (e.g., Eppinger et al., 2013, Philander and Rozendaal, 2013) to constitute the link between geology and metallurgy. The geometallurgical approach can provide specific data to geology, mining and mineral processing development and plant operations. The scope of the automated mineralogy is to illustrate how mineral quantification can improve the understanding of inherent mineralogical parameters in relation to metallurgy, and reduce the technical risk in both exploration and flowsheet development."

Jan 1, 2016

By E. Dernedde

Industrial plants located in the province of Quebec, Canada, are subjected to large variations of the ambient air temperature, Building ventilation systems of these plants must have some flexibility in order to meet industrial hygiene standards (TLV for chemical substances, heat stress and cold stress) at any time of the year, The building ventilation of a bath treatment plant of an aluminium smelter in Quebec was examined under summer and winter conditions, Part of the plant has periodic emissions of hydrogen fluoride gas and heat from hot anode butts, CFD modeling was used to optimise the building ventilation of the bath treatment plant, The present study proposes a modified building ventilation system, which improves the internal environment, complies with industrial hygiene standards and also reduces heating costs by 20 % during winter.

Jan 1, 2005

By K. Esmaieli

This paper addresses issues associated with ore pass degradation caused by material impact. A series of numerical experiments, using the particle flow code, were undertaken to investigate the influence of various finger raise configuration. This has allowed the identification of favorable configurations. The results of this analysis, when coupled with field observations, can contribute to the design of ore pass systems that can prolong the useful operating life of ore pass systems.

May 1, 2009

By V. Ogarlaci

Over 90% of the Romania's lignite reserve is located in the region of Oltenia, which is why this area is given special attention in the country's coal resources. Because the lignite deposit of Oltenia is comprised of 1-8 exploitable coal layers, their capitalizing calls for urgent arrangements to ensure rational exploitation under conditions of total safety, minimum losses and efficiency. The technology used the coal pits of North-Western Oltenia is the technology of excavation, transport and dumping in a continuous flow by using the complexes of excavation, transport and high-capacity dumping. The theme of this paper is of particular importance because the rhythmic operation in complete safety, is necessary both for sizing and keeping within the bounds of acceptable values, throughout the process of excavation of the geometric elements of the coal faces, marked by: the height of benches, slope angle and width of berms. Geometric dimensions of the benches of the open pits, the height of benches, slope angle and width of berms shall be calculated and shall be based on: the massif structure that forms the benches; physical-mechanical characteristics of rocks from the bench; working conditions, characterized mainly by mining and extraction methods applied; functional parameters of the mechanical equipment used to perform various operations on the coal face etc. For this study it was necessary a broad field for task tracking, measurement, research and design elements of the coal face, for land survey and a desk activity by: processing of topographic data, laboratory analyses on physical and mechanical properties of rocks and numerous specialized studies. In the final part, we bring some contributions to elucidating the issues of special importance for the lignite coal pits of Oltenia, coming up with data, graphics, formulas, solutions and concrete dimensioning of coal faces in terms of using technology in a continuous flow.

Aug 1, 2013

By M. Jahazi, M. Brochu

This paper describes the advantages/disadvantages of electron beam freeforming using two different types of filler metal: (1) brazing paste and (2) solid wire. Sound buildups were obtained from both filler metal. The freeforms produced with the brazing paste showed a certain level of porosity, which was reduced by successive melting. In comparison, the solid wire buildup was practically free of pore. When compared with the solid wire filler, the brazing paste produced narrower buildups but a larger scattering of the width.

Jan 1, 2004

By T. Verdel, Y. Gunzburger

Rockfalls are major and essentially unpredictable sources of danger, particularly along transportation routes (roads and railways). Thus, the assessment of their probability of occurrence is a major challenge for risk management. From a qualitative perspective, it is known that rockfalls occur mainly during periods of rain, snowmelt, or freeze-thaw. Nevertheless, from a quantitative perspective, these generally assumed correlations between rockfalls and their possible meteorological triggering events are often difficult to identify because i) rockfalls are too rare for the use of classical statistical analysis techniques and ii) all intensities of triggering factors do not have the same probability. In this study, we propose a new approach to investigate the correlation of rockfalls with rain, freezing periods, and strong temperature variations. This approach is tested on three French rockfall databases, the first of which exhibits an outstandingly high frequency of rockfalls (approximately 950 events over 11 years), whereas the other two databases are more typical (approximately 140 events over 11 years). These databases come from (1) the national highway RN1 on La Réunion Island, (2) a railway in the Bourgogne-Franche Comté region, and (3) a railway in the Auvergne region. Whereas a basic correlation analysis is only able to highlight an already obvious correlation in the case of the “rich” database, the newly suggested method appears to detect correlations even in the “poor” ones. Indeed, the use of this method confirms the positive correlation between rainfalls and rockfalls on La Réunion Island database. This method highlights a correlation between cumulative rainfalls and rockfalls in the Bourgogne region, and it detects a correlation between the daily minimum temperature and rockfalls in the Auvergne region. This new approach is easy to use and also serves to determine the conditional probability of rockfall function of a given meteorological factor. This approach will help to optimize risk management in the studied areas based on their meteorological conditions. Nevertheless, even if some rockfalls are correlated to meteorological factors, other seems to occur independently of these factors, which highlights the unpredictability of rockfall hazard.

Jan 1, 2015

By Masatake Haruta

Gold can be deposited as nanoparticles on a variety of support materials by coprecipitation or deposition-precipitation of Au(OH)3, grafting of organo-gold complexes such as dimethyl-Au(III)-acetylacetonate, mixing of colloidal Au particles, and vacuum deposition. Owing to the moderate adsorption of at least one of reactants (for example, CO) on the edges and corners of Au nanoparticles and to the activation of the counter reactant (for example, O2) at the perimeter interface with the supports, supported Au nanoparticle catalysts exhibit unique and practically useful catalytic properties at relatively low temperature below 473K. They have already been commercially used for deodorizers in rest rooms in Japan and will find growing applications in indoor air quality control, pollutant emission control, production of hydrogen energy carrier, and innovations in chemical processes. Cluster science of Au may also open an exciting area of research showing some magic numbers for dramatic changes in reactivity.

Oct 1, 2003

By J. A. McLennan

Geological uncertainty is an unavoidable characteristic of all mining projects since only limited information is available from sampling. Mine planning and development decisions with significant economic consequences are made when the geological heterogeneity is inherently uncertain. Geostatistical simulation is preferred over kriging because the methodology provides alternative property realizations that can be combined into a model of geological uncertainty. Geological uncertainty can be transferred into production uncertainty, which can help characterize the economic risk of the project. This paper presents a case study for the Pogo property, being prepared for development near Fairbanks, Alaska. The exact dimensions, grades and production predictions have been modified; however, the methodology is illustrative. The geostatistical methodology consists of (1) assembling the relevant drillhole data and establishing a suitable coordinate system, (2) calculating the target distribution, (3) creating a model of spatial correlation, (4) generating multiple realizations at a small scale and (5) linearly averaging all the realizations to the chosen selective mining unit (SMU) support size. The geostatistical model is then used to calculate production uncertainty.

May 1, 2004

By David deVries, James Rajith, Paul Mascrenhas, Nurzhan Dyussekenov, Lawrence Hanschar

Kansanshi Copper Smelter commenced operation in March 2015. The smelter features four Peirce- Smith Converters (PSCs) operated in a three hot, two blowing configuration. This paper describes some of the process automation and design features implemented to maximize operational and environmental performance. To ensure that the converters were easy to operate, efficient, and were protected in emergency situations such as power failures or loss of tuyere air supply a significant focus was placed on automated sequences initiated by “one button” operator commands or otherwise automatically by the Distributed Control System (DCS). Examples include: main converter roll-in and roll-out sequences; emergency roll-out in the event of power failure; and the charging sequences for reagents (silica and reverts). Other automated features configured for the PSCs were specifically aimed at maximizing converter capacity and reducing the environmental impact from fugitive emissions. These features include: “one button” in-stack charging; automated restriction of blowing rate based on the available acid plant capacity; and fully-automated control logic for the Secondary Ventilation System. In-stack charging allows anode furnace oxide slag to be poured into the PSCs while the converters are still blowing and still sending off-gas to the acid plant. PSC Secondary Ventilation control logic was configured to require minimum input from the operators while ensuring maximum utilization of the available draft from the ventilation system. Highly automated PSC controls contribute to high utilization, averaging 41.2 in-stack hours per day. INTRODUCTION Kansanshi Copper Smelter (KCS) is located near Solwezi at Kansanshi copper mine in Zambia's Northwestern province. The smelter treats concentrate produced at Kansanshi mine as well as Sentinel mine located 150 km west of Solwezi. Four Peirce-Smith Converters (PSCs) are installed at KCS. The nominal capacity of each converter is to treat 350 t of copper matte and produce up to 250 t of blister copper per batch. Normally three PSCs are hot, with two able to operate (produce off-gas), and the third converter on hot standby. The fourth converter is normally under cold repairs. The blister charge size is relatively low for the matte charged due to the unavailability of tank house or other high copper scrap.

Jan 1, 2019

The Anglo Platinum Mogalakwena North concentrator was one of the first three hard rock mineral processing applications to utilise a HPGR circuit in preference to a SAG milling circuit. This was driven by the extreme competence of the ore that had given rise to throughput issues on the original South Plant. Despite more than adequate capacity and performance of the individual comminution units, the circuit has struggled to obtain full design capacity. A thorough review of the integrated performance of the circuit revealed a wide range of bottlenecks and underutilised parts of the circuit arising from design issues. Interestingly, the major opportunities lie in materials handling issues and mismatch of loads about the circuit. This paper presents the high-level outcomes and the associated opportunities, and is pertinent to all HPGR circuit designs.

Jan 1, 2012

By J. H. Archibald

"IntroductionShot-saws are used for sawing rock throughout the dimension stone industry especially in granite quarry mills. Shot-saws, as currently designed, have an inherent wear problem which leads to slow cutting rates and repetitive blade changes which consumes much time. Because the saw blades are made from steel the abrasive shot used with them is limited to a certain hardness which effects the over-all efficiency of the sawing operation. Suggestions are made toward optimization of blade design and the sawing process. Blade DesignA common steel blade design is shown in Figure I. Note the perforations in the blade. These perforations or holes in the blade serve two or three purposes. The most obvious reason is to allow the abrasive shot a pocket in which to collect at the bottom of the blade, so that it can be distributed from these pockets into the cutting zone underneath the blade. The abrasive is fed to the saw in a slurry and usually comes in from the top. The blade must then cut a kerf wider than itself in order that the abrasive grains have a path leading from the top of the blade, down along its sides, and finally reaching the pockets and cutting zones. This circuitous path followed by the abrasive leads to side wear on the blades and high friction which can lead to blade buckling in severe cases. However, the fluidized path of the abrasives down the sides of the blade serves another purpose which is a positive gain if conditions are properly controlled. The abrasive slurry interacts with the perforations of the blade, the blade itself and the rock. This gap and the perforations in the blade, which are fluid filled, are sites of constant shearing motion. Eddy currents form in these gaps and pockets which tend to stabilize the blade by setting up balanced hydrodynamic forces which otherwise might not form in a non-perforated blade. A stable blade produces a more uniform cut in the rock. The third and final reason for the perforations are to allow the blade to wear in such a fashion that new pockets are always being formed and, consequently, new cutting surfaces between these pockets are also formed."

Jan 1, 1993

By G G. Suffel

T HESE remarks on the occurrence of strata-bound massive sulphide deposits are submitted be-cause the writer recently visited the principal Cyprus deposits (in January, 1965) and has also a back-ground of many years spent largely in detailed observation and map-ping of the Horne and Amulet ore-bodies, now largely inaccessible. They are particularly related to the Symposium papers (September Bulletin) by Hutchinson and by Roscoe. Some comments are offered on the cupriferous pyrite deposits of Cyprus. As the writer is currently reviewing the published literature on the related deposits in Turkey, a brief account of some characteristic Anatolian sulphide occurrences is given. The discussion is closed with some thoughts on the relationship between these Mediterranean sulphide deposits and those of northwestern Quebec and the Superior province in general. The geology of Cyprus, as it relates to the sulphide deposits, is well summarized by Hutchinson (1965). After visiting Mavrovouni, Skouriotissa and Limni and after much thought on the possible ge-nesis of these ores, it seems quite logical to me that he is right. They are indeed closely related to late-stage submarine volcanism.

Jan 1, 1965

By John L. Bonus

"WITHIN THE BROAD PARAMETERS implied by the title of my speech, I propose to deal more particularly this evening with a subject the many aspects of which have constituted the essential elements of one of the main thrusts undertaken by the MAC in the past two years, i.e., to create among Canadians a much greater awareness of the importance of mining and to demonstrate to them what are the many and varied benefits they derive from mining activities across their country. In other words, MINING - WHAT IT MEANS TO CANADA.I also intend to discuss some aspects of government-industry relationships.I am very conscious of the fact that I am speaking to an audience made u in large part of experts in several fields of mining and exploration activities. They will be familiar with many of the points I intend to discuss. However, without in any way suggesting that familiarity breeds contempt, might I emphasize that even in this particular forum there is justification for reiterating some of our basic philosophies and suggesting ways whereby they might be better understood and promoted.Let us first summarize the present dimensions of the Canadian mining industry."

Jan 1, 1971

By A. F. Matheson

"Bankfield Consolidated Mines, Limited, and Tombill Gold Mines, Limited, in the Little Long Lac area, Ontario, mined an orebody that was common to both. The discovery' of this orebody was made by surface prospecting in May, 1932, on Bankfield ground, following an original discovery made in the same manner on the same property on a small reef in Magnet lake in October, 1931. The production from the two mines between 1937 and 1942 was approximately 135,000 oz. gold from about 420,000 tons of ore, an average grade of 0.32 oz. a ton. Production was nearly equally divided between the two properties. Both mines are now closed, the ore exhausted.""The ore is mainly sheared and fractured greywacke and porphyry impregnated by silica and small amounts of metallic minerals. To a lesser extent there are definite quartz veins in the ore zone""(l). The metallic minerals present were principally pyrite, arsenopyrite, pyrrhotite, and native gold .As at other mines in the Little Long Lac area, an elongated, broad, deep trough of folded, steeply dipping volcanic and sedimentary rocks, striking roughly east-west and surrounded by younger granite, is host to the orebodies of the Bankfield and Tombill. In the immediate area of the two mines iron formation and conglomerate bands occur nearby both north and south of an intrusion of porphyry-Cliorite, suggesting repetition of beds and folding. Although considerable drag folding is in evidence, folding on the above scale has neither been proved nor disproved."

Jan 1, 1954

By B. W. Smee

Glacial lake sediments or glaciolacustrine deposits form a significant portion of the Canadian, Scandinavian and Russian landscapes. Furthermore, 50 per cent of the Archean volcanic belts within the Canadian Shield area are covered wholly or in part by these deposits. Because of the high electrical conductivity and low hydraulic conductivity of these compact sediments, the application of geophysical (electrical) and geochemical techniques in such areas becomes a difficult task. The presence of these sediments has therefore hampered exploration for metallic sulphide deposits in some of the most important metallogenic environments of Canada. Similar problems exist in some tropical countries, such as Australia, where the overburden may be very conductive. In this paper, the extent and provenance of the glaciolacustrine deposits within the Canadian Shield are described. The geochemical and geophysical factors that hinder exploration in the clay belts are reviewed, with case histories of successful and unsuccessful applications of some of these techniques. The most successful geochemical technique used within glacial clay belts is the sampling of lodgement till beneath the clay cover, and the analysis of the heavy mineral fraction of that till. Surficial sampling has not been successfully applied. Some geophysical techniques, more specifically electromagnetic and magnetic induced-polarization techniques, have detected mineralization beneath substantially deep clay or saline overburden layers. Some suggestions have been made, such as the use of anions in hydrogeochemical surveys and the use of wide-band multi-frequency EM systems. When implemented, they will hopefully make the current geochemical and geophysical methods more effective in exploration for base metal sulphides within clay-covered terrains.

Jan 1, 1979

By John F. Haberer

DURING the twentieth century Canadians have been steadily improving their standard of living. Originally, this improvement depended almost entirely upon the export of basic raw materials and a triangular system of trade with Great Britain and the United States. However, since the Second World War, Canadian living standards have improved still further because of the very rapid d0evelopment of secondary industries. As a result of this development, the present demand for scientists and engineers exceeds the supply, and interest in scientific research has never been greater. It is the purpose of this paper to discuss the professional and economic status of Canadian scientists and engineers over the past half century. GROWTH OF RESEARCH It is difficult to determine accurately the amount of scientific research conducted in Canada since 1900. However, ?prior to World War I, it was limited and was connected mainly with primary industries and health. Government departments did some; university science faculties, overloaded with teaching responsibilities, did a little; and industry, which consisted mainly of subsidiaries of American and British firms, depended chiefy upon foreign sources for new information.

Jan 1, 1956

By Ludwig Strah

"The paper outlines the history of rubber mill liners beginning with the awarding of the first North American patent rights in 1923. It includes the early-day applications and installations of the 1920s and 1930s through to their present-day application. Over-all rubber mill liner design is discussed in relation to present day installations employing rubber mill liners in various grinding applications. A brief overview is given of a manufacturer's procedures to produce rubber mill liners.IntroductionIn early 1910, it became apparent that the productive life of the silver mines in Cobalt, Ontario, could be substantially prolonged by mining lower-grade ores.The mining of lower-grade ores required the establishment of treatment facilities which initially employed jaw crushers, stamp mills, jigs and concentrating tables. The recovery of silver in other than a coarse metallic form required the additional step which was introduced at that time: the cyanidation of silver concentrates from the tables. The resultant requirement for increased and improved recovery led to the introduction of grinding mills, i.e. tube mills.Shortly after the introduction of the tube mills to the Nipissing Mine's mill in 1914, the idea of using rubber as a mill liner material was spawned. However, no action was taken due to the advent of World War I. It is interesting to note that the idea of rubber mill liners emanated from having used pieces of solid rubber tire as an emergency repair on a set of liners when a liner had broken and no immediately available spare was on site.The credit for this ingenuity and subsequent application for a patent on rubber mill liners falls to James John Denny, the mill superintendent, and Rolla Barnum Watson, the general manager of Coniagas Mines Limited. The patent application was formally made on December 3, 1921. The U.S. Patent Office issued Patent No. 1,470,597 on October 16, 1923."

Jan 1, 1982

By The Mill Staff

"IntroductionCOMMENCEMENT of operations at the new No. 7 shaft and 10,000-ton mill at Creighton mine was a major step in the programme of conversion to all-underground mining by the International Nickel Company of Canada, Limited. Planned ten years ago, the orderly transition has been greatly speeded-up to offset the heavy drain on production imposed by World War II and also to meet the increased demand for nickel caused by the current international situation. Development of new mining methods, and process changes in the reduction plants, have made possible the economic recovery and utilization of ore of lower grade than formerly used and of varying metallurgical characteristics. By 1953, when the Company's open-pit mining operations are scheduled for completion, the hoisting capacity of its five underground mines in the Sudbury district will have been increased to 13,000,000 tons per year, compared with 5,700,000 tons of underground ore hoisted in 1950.Two types of ore occur at Creighton. One is a breccia and stringer type that contains a high percent-age of massive sulphides and is located in sheets along shears and in large and small pockets on the underside of the main norite mass; the other type, forming the main part of the ore zone, is mineralized norite that occurs as a •sheet up to 400 feet thick overlying tl1e breccia ore. In both types of ore the minerals of economic interest are pentlandite, which is intimately associated with pyrrhotite, and chalcopyrite. Early mining was confined to the breccia ore; this ore was mined by open stoping methods. The hanging-wall was later allowed to cave, with the result that the old stopes are now filled with caved low-grade ore."

Jan 1, 1952

By L. D. van Dyk, G. S. Tshofu

Iron ore fines are by-products of iron ore mining operations. Unlike iron ore lumps, fines cannot directly be used in conventional iron making processes, and consequently large quantities accumulate around the world. Pelletizing and sintering can be used to convert iron ore fines into agglomerates or briquettes for processing with lump ore, but these techniques are energy intensive and produce greenhouse gases. This research investigated the extraction of iron from iron ore fines using acetylacetone (a ß-diketone) as an environmentally friendly alternative process for fines utilization. A 2k factorial experiment design was used to identify the significant extraction variables. It was found that the reaction temperature and solid to liquid ratio had significant effects on the extraction process. The extraction kinetics were studied at different temperatures and the highest iron extraction (97 %) was obtained after 48 hours at 413 K and 0.025:1 (g:mL) solid to liquid ratio for a particle size range of +106 to -150 µm. The extraction products were easily separated from the unreacted acetylacetone by flash distillation and iron(III) acetylacetonate crystals were recovered. An economic evaluation showed that selling the crystals was profitable. Alternatively, the crystals can be reduced with hydrogen to iron particles and acetylacetone (for reuse).

Jan 1, 2015