Search Documents

By John Frostiak, Lloyd Buckingham, Kenneth G. Thomas, Luis Wilson

"The El Indio roasting facility associated with El Indio Mine in Central Chile has operated since 1981. It is a facility developed to remove arsenic and antimony from gold bearing enargite/pyrite flotation concentrates.The three installed roasters are Nichols Herreschoff units each with 14 hearths and measuring 4.85 metres diameter. Hearths are rabbled by central shaft driven rabble arms. Product is progressively heated to 750°C under neutral to reducing atmospheric conditions to drive off labile sulphur, arsenic and antimony.Ancillary equipment includes skip hoist feed arrangements, water cooled screw conveyors for transporting and cooling calcine, gas cyclones, post combustion chambers, heat exchangers, electrostatic precipitators, bag houses, gas scrubbers and packaging facilities .Operating practices, history, mineralogy and results are reviewed. The improvements to arsenic and antimony extraction, ambiental conditions and environmental achievements are discussed.INTRODUCTIONHistoryThe El Indio property lies in the El Indio belt, a copper, gold and silver area approximately 175 km long by 10 km wide. The property is located in the Andes Mountains of the central part of Chile at latitude 30"" South and 160 km from the sea-side city of La Serena. Plant location is at 3850 meters above sea level.The property currently consists of two underground mines feeding the El Indio plant and an open pit feeding the newer Tambo leach plant. The property has been controlled by a succession of owners (St. Joe Minerals, Fluor, Bond Gold International and Lac Minerals Ltd.) before acquisition by Barrick Gold Corporation in 1994."

Jan 1, 1999

By C. E. Baltzer

This is the fourth in a series of coal technology reviews being prepared. in accordance with a recommendation voted by the Coal Division C.I.M. in session at the Jubilee Meeting, Vancouver, 1948, that the Department of Mines and Resources be requested to arrange for publication by the proper Government authority of a Quarterly Review of Coal Technology for distribution among those concerned in the production and use of coal in Canada. Copies of the first review, which appeared in the November, 1948, BULLETIN, pp. 612-614, of the second review in the June, 1949, BULLETIN, pp. 272-275, and of the third review in April, 1950, BUL-LETIN, pp. 1,9?3-196 (also, respectively, in Transactions, Vol. LI, 1948, pp. 262-264 Vol. LU, 1949, pp. 117-120, and Vol: LIU, 1950, pp. 133-136), were distributed by the Dominion Coal Board and are still available on request. In this review, the first in the series in the field of combustion, development and trends during the period approximately from World War II to the present time are described and therefore the presentation is general. Later reviews will particularize developments in relation to the range of coals available in Canada.-ED. INTRODUCTION THE utilization of coal in heat and power producing equipment has become of paramount importance to the coal industry in maintaining stable and profitable markets. In the past, the chief concern was with mining, transportation, and overall supply problems, but modern conditions demand interest in and knowledge of all phases of the product, from coal in situ to its ultimate disappearance in the form of products of combustion. Even the last mentoined factor has caused complications, as is shown by current widespread activity in the field of smoke abatement

Jan 1, 1951

By Premil Agarwal, Alok R. Patnaik, Pulak Dhar, Prakash C. Patnaik

In this study, a physics based model has been presented, considering the growth of the thermally grown oxide (TGO) layer on the bond coating of a thermal barrier coating. Using diffusion equations, a model has been developed to physically describe the oxidation process. The mathematical equations representing the diffusion formulations have been solved numerically. The computed results show the depletion of Al in the bond coating as it diffuses both towards the super-alloy substrate and towards the TGO produced in between the bond coating and the ceramic TBC top layer.

Jan 1, 2004

By James A. Finch

"I offer a personal view of what the next 30 years holds for mineral processing. Re-stating that mineral processing will remain a vibrant industry in raw material production, growth opportunities in waste management are identified. The processing sequence familiar now (mining -mineral processing -extraction) will become more interwoven. In situ processing (i.e., milling underground) will evolve from concept to demonstration. Opportunities to exploit physical properties altered in chemical (pyro-and hydro-) processing will present themselves. In primary grinding, the path to AG/SAG milling will progress with little deviation but opportunities in regrinding are wide open. Flotation will see the trend to designing bubble/particle reactors accelerate simultaneously with a vigorous response from mechanical cell suppliers. Gravity separation remains a bastion of the lone inventor but I anticipate that the new lines will come from the waste management business. I finish by examining the ""research cycle"", identifying growth in small ""high tech"" companies and university research centres.IntroductionI have been asked to offer a personal view of""where we are going in mineral processing?"". Gazing into crystal balls is quite a cottage industry as we approach the end of the millennium. Academics are often asked to assume the role of visionary, I presume because it is considered in their mandate, to reflect and philosophize (or, less charitably, because they are considered to have the time). Since this is the 30th Annual Canadian Mineral Processors Operators Conference, I am tempted to suggest the next 30 years as my frame of reference. This is about equivalent to one engineer's career or, given it takes typically 15 years to go from concept to realization in mineral process engineering (Napier-Munn, l 997a), about 2 ""invention cycles"". With this length of cycle, much that is familiar now will remain so over the 30 years.Research and development (R&D) is in response to need. The overarching need in mining is to find new ore bodies. Process developments cannot compensate for a depleting deposit or a declining commodity price. Mineral processing R&D is characterized by incremental gains, aimed at pushing the mine down the cost per tonne league table. Breakthroughs are the exception (flotation at the turn of the century was one). This must be kept in mind when trying to predict the future in our business."

Jan 1, 1998

By Frank Ebbutt

In this paper it is proposed to point out certain structural factors that; have an important bearing on gold deposition. The subject will be treated; more or less generally. Although the writer has had access to a great many; of Canada's gold mines he does not wish to take the liberty of discussing; details of any particular mine or mines; the aim will be to discuss controls; that are evident in many places.

Jan 1, 1954

By R. W. Thompkins

The two largest contributors to silicosis in machine men are dust from drilling and dust from blasting. With the advent of the shatter-cut method of blasting, the evils of blasting dust were greatly reduced. The problem of dust from drilling has been attacked from two different angles: (1) The adoption of dustless frontheads or enlarged water tubes, both of which have proved capable of reducing dust concentrations; and (2) The adoption of better ventilation. Many operators are loath to adopt dustless frontheads or enlarged water tubes on Leyner drills because of the increased repair costs on drills, and also because it has been found difficult to enforce 'the proper usage of dustless machines: for example, workmen sometimes plug the vents in the fronthead.

Jan 1, 1943

By Michel Dostie

Un séchoir à vis chauffé par induction électromagnétique a été développé et implanté chez Mines Niobec pour le séchage d?un concentré de niobium. Ce séchoir a permis une réduction des émissions de poussières et des gaz à effet de serre de l?usine. Il offre une grande souplesse de contrôle, une meilleure efficacité énergétique et peut être utilisé pour le séchage de granulats, de poudres ou autres substances habituellement traitées dans un four rotatif ou à l?aide de vis chauffées par un caloporteur. Le principe de fonctionnement du séchoir est simple. Trois inducteurs opérant à la fréquence du réseau électrique assurent le chauffage des parties métalliques du séchoir, dont des vis qui servent à convoyer le matériel. Le contact du matériel avec les parties métalliques chaudes permet le transfert de l?énergie requise pour le séchage. La conception de ce type de séchoir requiert un équilibre adéquat entre les besoins associés au chauffage par induction et ceux liés au transfert de chaleur par contact et au transport du matériel dans le séchoir. Cette première implantation industrielle a nécessité des efforts de développements importants et une collaboration des différents intervenants. Une revue des principes de conception, des difficultés rencontrées et des performances obtenues sera présentée.

May 1, 2007

By J. E. Gill

"The Wasa Lake property is a block of about 1,640 acres in Beauchastel township, Quebec. Gold was discovered there first in 1936 in what is now known as the 'Southern area ( Fig. 1). Stripping and trenching were followed by 9,218 feet of diamond drilling in twenty holes. A number of good intersections were obtained, but their interpretation in terms of ore was difficult. A shaft was then sunk to 220 feet vertical depth. Thirteen hundred feet of lateral work and 543 feet of diamond drilling were completed at the 200-foot level before work was discontinued in 1938. Results up to this point had been just fair.Early in 1944, surface diamond drilling was resumed. The first hole cut material of ore grade in a strong shear zone 1,000 feet north of the old workings, and holes to the east and west showed this to be an extensive gold-bearing zone.In August 1945, a main working shaft was started. This has been sunk to 550 feet slope depth. A cross-cut at 390 feet vertical depth was driven to the ore zone and, by drifting and drilling at regular intervals, a length of 725 feet had been tested to December 31st, 1946 ( Figs. 1 and 2). The results check those from surface drilling quite closely.In the main zone, scoping widths from 8 to 40 feet and averaging about 25 feet are indicated. The grade after dilution should be about 0.15 oz. gold a ton and operation will probably start at 1,000 tons a day."

Jan 1, 1954

By J. Parreira

This paper presents a deterministic/stochastic model that was created to compare an autonomous haulage truck system to a manual one by calculating and estimating benchmarked Key Performance Indicators (KPIs) such as productivity, safety, breakdown frequencies, maintenance costs, labour costs, fuel consumption, tire wear, and haulage cycle times.

Aug 1, 2013

By E. Wolmarans

The selection of the main mineralised zone (MMZ) concentrator milling circuit has followed a comprehensive route over the preceding 10 years. Many knowledgeable parties have contributed and assisted in developing the milling circuit according to the best available information. The final selection of the flow sheet was completed after DRA conducted a techno-economic study on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous (AG) milling. The results from all the above mentioned work indicated that it is possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding circuit. The flow sheet was designed to treat the main mineralised zone (MMZ) arising?s from both underground and open cast operations and incorporates a fully autogenous grinding (AG) circuit. Commissioning of the 375ktpm concentrator at Nkomati Nickel began in August 2009 with the first ore reporting to the mill on the 15th of September 2009.

Jan 1, 2012

By M. Mezbahul-Islam

Thermodynamic modeling of the Mg-Cu-Ni system is carried out as a part of multi component thermodynamic database for Mg alloys. This system is being modeled for the first time using the modified quasichemical model, which considers the presence of short range ordering in the liquid. The thermodynamic descriptions of the binaries Mg-Cu, Cu-Ni and Mg-Ni have been extrapolated to the ternary Mg-Cu-Ni system using Toop geometric model. The constructed database has been used to calculate and predict thermodynamic properties, isothermal sections and liquidus projections of the Mg¬Cu-Ni system, which showed very good consistency with the experimental data.

Jan 1, 2011

By E. H. Dudgeon

In order to make increased use of automation in copper smelting, it is evident that a useful first step .world be the accurate determination of the copper end point in the converter operation. After laboratory tests, the copper end points in a copper converter at Gaspe Copper Mmes Ltd. were determined without reference to melt samples or other observations. The results indicated that the rapid measurement of the S02 level in the gas released from the converter has potential as a new and independent method of determining the copper end point in converter operation.

Jan 1, 1966

By Claude Bazin, Patricia Obiang

"The slurry density (pulp percentage of solids) and the size of the grinding media are often used for the optimization of an operating ball mill. In many cases a change of ball size is made at the slurry density used with the original ball size. But is the optimum slurry density changing with grinding media size? Laboratory grinding tests were conducted to answer that question and results indicate that more than likely there is no need to adjust mill slurry density when adjusting the size of a grinding media in a ball mill. Full scale behaviour could be different because slurry density affects the slurry transportation through the mill and the classifier operation.INTRODUCTIONOre preparation begins with a fragmentation step that liberates valuable minerals or exposes mineral surface to the environment. The size reduction step of a mineral processing operation is energy demanding and the optimisation of this process should always be an objective for the plant metallurgists. Various approaches could be considered for improving the operation of a grinding circuit. For a close grinding circuit an adequate tuning of the classifiers operation may lead to substantial savings (McIvor, 1988). Once a grinding mill is in operation, few variables remain to be considered for process optimization. The ball charge is usually maintained to achieve a target power drawn by the grinding mill motor. The rotation speed is seldom considered (McIvor, 1983; Bazin and Lavoie, 2000) as a change of mill speed usually implies a costly pinion change. If the liner and lifter configuration is critical for SAG and AG mills (Latchireddi et al., 2005), few discussions are available for ball mills (Fuerstenau and Abouzeid, 1985; McIvor, 1983). The mill feed size distribution can also be adjusted but this implies changing the upstream processes, which transposes the optimization process to another level. Modification to grinding media shape is a possible avenue (Cooper et al., 1994), but it remains that slurry density and grinding media size are probably the most frequently considered variables for the optimization of a ball mill."

Jan 1, 2007

By G. M. Ritcey, S. H. Lucas

"On the north shore of the St. Lawrence River, in Quebec, are located orebodies of low-grade titaniferous magnetite. The Quebec Mining Exploration Company (SOQUEM), who have an interest in the deposits, believed that beneficiation of the could generate sufficient revenue to defray the mining costs and the costs of transporting the ore to a steel production facility. A joint research project of SOQUEM and CANMET investigated alkaline roasting of a magnetic concentrate, followed by leaching of the calcine and separation and recovery of Cr and V by solvent extraction. Aluminum was recovered by precipitation.The present paper describes the roast-leach bench-scale and pilot-plant work leading to the development of the optimum conditions f or the integrated process.A plant flowsheet was developed for the treatment of 5 x 106 tons of magnetic concentrate per annum. Estimates of capital and operating costs were made.Based on a recovery of approximately 90% V, 85% Cr and 75% AI, the total hydrometallurgical plant fixed capital costs, including mining, concentration and shipping, are estimated at $1.021 x 109; the operating costs are estimated at $131.92/ton concentrate. Annual revenue from the Na2CrO4.H2O, V2O5 and A12O3 produced is calculated to be $421 x 106.IntroductionThe Quebec Mining Exploration Company (SOQUEM) acquired in 1968 an interest in four titaniferous magnetite orebodies located in Eastern Quebec. 85 miles north of Mingan on the north shore of the St. Lawrence River. The Mingan deposit, with an estimated tonnage of one billion tons, has a reported average grade of 43% Fe, 6.3% Ti , 1.60% Cr, 0.19% V and 6.1% Al with minor amounts of nickel. SOQUEM, on the basis of previous bench-scale data, believed that the recovery of chromium, vanadium and alumina by alkaline roasting would generate sufficient revenue to defray the mining costs and the costs of transporting the ore to a steel production facility on the coast. One of the approaches selected by SOQUEM for beneficiation of the ore consisted of a combination of magnetic concentration followed by alkaline roasting of the calcine."

Jan 1, 1980

By Waldbillig. D.

A baseline of the poisoning effect of hydrogen sulfide (H2S) fuel impurities on solid oxide fuel cell (SOFC) anodes was developed using polarization testing. After the baseline behaviour was characterized, tests to study the effect of various H2S concentrations on the rate and amount of cell voltage degradation and recovery were performed. Attempts were made to improve the rate and amount of recovery by various methods. Testing was very reproducible, but significant electrochemical performance degradation was seen after all H2S poisoning tests even at an H2S concentration of 0.1 ppm. Degradation is initially quite rapid, but after a period of time the rate of degradation levels off. After poisoning was complete, the H2S flow was stopped and the cells were allowed to recover. Some recovery was seen after poisoning, but cell performance was never fully recovered.

Jan 1, 2005

By I. Ueda, S. Ishikawa, T. Nagata

“O-SR process” in which the S-Furnace of the Mitsubishi process is followed by existing reverberatory furnaces (RFs) and Peirce Smith (PS) converters has been operated since December 2007. The S-Furnace smelts copper concentrates to produce molten matte containing 58-62%Cu which is then settled in the RFs and converted to blister copper in the PS converters. The SO2 gas generated from the S-Furnace and PS converters is converted to sulfuric acid in the acid plants. In addition to the smelting copper concentrates, the O-SR process has advantages in terms of recycling various waste/secondary materials. Automotive Shredder Residue (ASR) has been treated in the RF to reduce fossil-fuel consumption in RFs, and to recover various metals included in ASR as well, since 1993. Electronic circuit boards (E-scrap) has also been processed in order to recover not only copper but also rare resources such as gold, silver and PGMs since 2013. Strategic modifications have enabled expansion of the processing volume of E-scrap. Enhancing recycling of wastes and scraps from urban mines while reducing the consumption of natural resources in the “O-SR” process will be demonstrated and discussed in the present paper. INTRODUCTION Onahama smelter and refinery has been operating as a custom smelter since 1965. Smelting facilities were subsequently expanded to two green-charged RF furnaces and five PS converters in 1973. Since RF is a conventional old-fashioned smelting furnace that necessarily consumes a huge amount of fuel to smelt copper concentrates, saving fuel cost has been an important objective. In early 1980’s the fuel was changed from bunker oil to pulverized coal, while utilizing the combustion heat of waste tires. Furthermore, treatment of combustible waste such as shredder residue (SR) was initiated in order to save fossil fuel for smelting concentrates in the RFs. Since enhancing of the treatment of SR requires a reduction in concentrate smelted in the RFs, most concentrates were dried and injected through tuyeres into the PS.converters. These modifications enabled to reduce the amount of the pulverized coal combustion and to increase SR treatment in the RFs. SR treatment capacity has increased to 12,000mt/month because the SR market has grown after the enforcement of the Vehicles Recycling Law. Such business environment has been attributed to establish the thermal-materials recycling system of SR in which the RFs have changed their role from copper concentrates smelting furnaces to waste materials combustion furnaces.

Jan 1, 2019

By J. Frostiak

"This paper describes some energy reduction measures Implemented at the Griffith Mine. Before proceeding, I will give you a brief overview of the operation.The Griffith Mine is an iron ore mining, concentrating and Pelletizing complex located in the red lake area of northwestern Ontario. The operation is owned by Stelco Inc. And is managed By Pickands Mather & Co. of Cleveland, Ohio. Operation of the concentrator commenced in 1968 and it has been producing at a nominal capacity of 1,500 ,000 tons annually.The plant flow sheet is illustrated in this slide. Run of the mine ore is crushed in a single stage 54"" gyratory crusher. Reclaim ore feeders draw from an open stockpile to feed two 32' diameter by 12' long autogenous mills, each driven by 6800 hp. Two s·rages of wet magnetic separation, roughers and cleaners, and primary cyclones complete the primary circuit. Cleaner concentrate is then ground in four 14' diameter by 28' long pebble mills rated at 2000 hp. The secondary grinding circuit is closed by cyclones and fine screens. Secondary cyclone overflow is further upgraded through hydro-separators, finisher magnetic separators and flotation.The magnetic concentrate produced is then thickened, filtered, balled and fired in three vertical shaft furnaces to produce a high quality hematite pellet."

Jan 1, 1983

By George E. Cole

"It is a truism that the metals, and particularly the precious metals tend to monopolize the attention of those interested £n the mineral industry. This is a tendency to be mildly, but actively and continuously combatted if we are to have a well-rounded mineral development." There are in the province of Ontario a number of industries centred about the non-metallic minerals. Too little is heard of the part these play in our industrial life. It is with the intention of showing what the gypsum industry is doing in Ontario that this paper is written. The writer lays no claim to any originality in the discussion and merely offers some material in an endeavour to assist in bringing about that 'well-rounded mineral development' sought for Ontario. M. Y. Williams in his "The Silurian Geology and Faunas of Ontario Peninsula and Manitoulin and Adjacent Islands"1 in discussing the industries dependent on the Silurian rocks of south-western Ontario points out that "the splendidly ordered gypsum mine at Caledonia, formerly owned by the Alabastine Company of Paris, and now owned by the Ontario Gypsum Company, is a revelation to the average man, who disconnects mining entirely with this part of Ontario". This region is better known as one of the richest and most thickly settled agricultural areas in Canada.

Jan 1, 1925

By H. J. McQueen

Pressure welding is a solid state joining technique that depends on bringing the parts into sufficiently close contact that inter-atomic bonds are achieved. Pressing is more effective at elevated temperatures where plastic flow causes the asperities to collapse; improved application conditions are derived from hot-work research to clarify temperature and strain rate dependence of hot strength and ductility. The substructure evolution systematically studied in hot working to determine dynamic recovery or recrystallization is applied to clarifying that developed in welding. The various processes are affected differently by work-piece geometry and final shape requirements. In addition to pre-cleaning of the surfaces, the plastic flow helps disperse the remaining oxide layers as was originally exemplified in blacksmith hot forging of layered sword blades and in bellldie welding of wrought iron tubes. The presentation critically compares the utility for various materials and configurations of simple pressure, ultrasonic application, diffusion, explosive, rotary and linear friction and friction-stir processes. Diffusion bonding (primarily Ti) with light cleaning, low pressure, little distortion in protective furnace atmosphere contrasts strongly with the heavy upsetting in friction welding, or complex alloy mingling and substructure variations in friction stir joints.

Jan 1, 2011

By Jerry Ran

When multiple levels are mined in open stope mining with delayed backfill, mining underneath fill is inevitable to achieve higher rate of recovery if no sill pillars are left for the purpose of fill separation or partial ground support. This is particularly true when the orebody has low reserves per unit vertical distance. Instability of the exposed fill back causes stope dilution, production delay and possible equipment damage and consequently increases the mining cost. Previous studies have concentrated on fill mat stability in cut-and-fill and stability of fill walls in open stope mining. Workers are exposed to the fill back in cut-and-fill and therefore smaller open spans are normally adopted and the fill mat is reinforced. In open stope mining openings with large spans are designed, workers are not exposed to the fill back and its stability has to be maintained by fill of sufficient strength. However, the required fill strength is normally determined by considering different modes of fill wall failure. The fill back stability is usually not analyzed in the fill design process. The lack of analysis on fill back stability for open stope mining is mainly due to difficulties in relating the fill properties to the fill and stope geometry. In this paper a simplified wedge model is adopted to analyze stability of the exposed fill back in open stope mining with consolidated backfill. The proposed method calculates the factor of safety of the fill back against shear failure under known fill and stope geometry and fill strength parameters in order to assess the fill back stability. It can also be used to determine the required fill strength with known fill and stope geometry. The proposed approach is indirectly validated by mining experience and observations at two operating mines. In addition there are many factors affecting the fill quality and stope configurations in an operating mine. These factors have to be considered in the analysis of fill back stability. This situation is highlighted by presenting an actual mining case where the fill back failed due to factors commonly encountered in mining operations.

May 1, 2003