Search Documents

By George Booth

In mining operations the cost of timber is an item of much importance, because the life of mine timbers is, in many cases, very short and, as the supply of the better grades becomes depleted, less durable kinds must be used. This, of course, tends to shorten still further the period of service-ability. While it is possible that concrete and steel may, to some extent, take the place of timber in mines, their high initial cost and the difficulty in installation will greatly restrict their use. Moreover, wood, besides being comparatively cheap to handle, possesses other desirable qualities, and for many purposes a satisfactory substitute is hard to find. Both the decreasing supply and the increasing price of timber make its more efficient utilization imperative. AGENCIES DESTRUCTIVE TO MINE TIMBERS Timber used in mines is exposed to destruction from many sources. Wear, breakage, and waste are responsible for much loss. Wood rollers and drum laggings must be frequently replaced on account of the constant wear by ropes. Unprotected timber in chutes and mills is also rapidly worn by abrasion, and track ties in main haulage ways get worn by the feet of mules, cut by ropes, etc. Large amounts of timber are broken by 'crush' and 'squeeze,' and much temporary timber is buried beyond all recovery in pillar workings and in those mines which resort to back filling. Decay and insect attack, however, cause the greatest damage. If not totally destroyed by one or both of these, the timbers frequently become so weakened that they break under the pressure upon them.

Jan 1, 1926

By S. P. Chong, N. C. Shih, G. A. Turner

Fine powders, with the bulk of the particle diameters Jess than 10 microns, were aerated so that each particle was, on the average, separated from its neighbours by 1.3 to 2 mean diameters. In this state, measurements were made of the viscosity and settling rate of the powder, and the interfacial tension between it and a moist pellet. From the viscosity measurements, qualitative analogies are drawn between the behaviour of the aerated powder and that of a dense gas near its critical point.

Jan 1, 1970

By Alan Bateman

Introduction A few years ago the name Katanga recalled, to those interested in copper, a far-off country in central Africa where deposits of huge size were beginning to pour a stream of copper into the world's markets. But no one heard of the adjacent part of northern Rhodesia as a potential copper region. It was then a bush-covered wilderness, with a few lonely, widely-spaced villages, and here and there a copper prospect that created but little outside attention. There was also one struggling mine whose development created pessimism. The low-grade carbonate outcrops of Rhodesia did not compare favourably with the rich carbonate ores of Katanga. And, since Katanga was mining only oxidized ores, it was then thought that this adjacent region likewise would contain only oxidized ores. The one mine that had been started, Bwana M'Kubwa, was working on low-grade carbonate ore at a loss. The outlook was not promising. But, a little over three years ago, the aspect changed. The vision of one far-sighted engineer embraced the possibility that here copper sulphides might underlie those low-grade carbonate croppings. His courageous associates furnished the capital; drilling commenced, and the great Roan Antelope mine rapidly emerged. In quick succession, the N'Kana, Mufulira, N'Changa, N'Changa Extension, and Chambishi mines were heard from. Prospecting and development are now proceeding apace, towns are being hewn out of the virgin bush, plants are being reared, and ramifying branch railways are being pushed out from the single line of steel that now connects Rhodesia with the coasts to the south. A great new copper-mining centre is in the making, about which the world will hear much in the future. As with most new mining camps, rumors abound regarding its ore possibilities; some are correct, some are erroneous, and reliable information unfortunately is all too scanty.

Jan 1, 1930

By B. H. Kim

It is hypothesized that the standard approach adopted to characterize the ground and to determine the rock strength properties at depth are flawed and generally tend to underestimate the rock strength and possibly the stiffness, particularly when the rock mass is characterized as massive to moderately jointed or blocky to very blocky. It is therefore necessary to conclusively established that the hypothesis, that the rock strength in highly confined rocks is greater than generally anticipated, is actually valid and generally applicable, and then to develop new procedures to establish rock parameters that can be reliably used for the design of deep excavation.

May 1, 2009

By Brian Hart, Stamen Dimov

"The Time of Flight Secondary Ion Mass Spectrometer (ToF-SIMS) is unique in that it measures the outermost atomic layers of any material. The technique is particularly suited for determining surface chemical composition of mineral particles. It is most commonly used as a diagnostic tool to measure mineral surface chemical variability in plant and bench top flotation separation processes. Recently, research towards understanding the full capability of the instrument has resulted in the development of new diagnostic applications related to various Au extraction technologies and the development of the ToF-SIMS as a predictive tool for assessing the chemical reactivity of the ore.In this paper we will present a brief review of the ToF-SIMS technique with recent advances in instrumentation and methodologies including:•,?recent developments and advances towards a semi-quantitative approach to the evaluation of mineral surface modifiers (ex. Cu),•,?flotation case studies investigating activator, depressant and collector loading variability within a flotation process,•,?the recently developed chemical reactivity test which we believe has the potential to predict the behaviour of minerals in a flotation test in response to chemical transfer during grinding,•,recent applications for determination of surface Au preg-robbed in carbonaceous materials.A portion of this material has been recently presented at the COM 2009 meeting and at SIMS XVII (see Dimov et al 2009 and Hart et al, 2009).INTRODUCTIONIn flotation seperation surface chemistry is the principal determinant for selective separation of the various mineral phases (Ralston, 1994, Smart et al, 2003). Determination of this hydrophobic/hydrophilic balance by particle therefore requires correct identification and selection of the particular mineral phase(s) followed by a statistical analysis of the surface chemical characteristics of the particles with an estimation of the spread of values (Smart et al, 2003)."

Jan 1, 2010

By Jay Tuttle

THE spiral stoping method of mining was first seen by the writer at the Granby Consolidated Mining, Smelting & Power Company's Hidden Creek mine, at Anyox, British Columbia. Where the method received its name, or by whom it was named, is a question, but it was employed by the Granby Company at their Phoenix mine, in the Boundary district, B.C., as early as 1901-02 after they had tried unsuccessfully other methods at that large, law-grade property. its adoption there was suggested by two miners, John and Steve Swanson, then working at Phoenix, who had previously been employed in the hard iron-ore mines of Michigan and Wisconsin, where they had learned this system of mining. The method proved successful at Phoenix and also, later, at the Company's Hidden Creek mine at Anyox, where some 40,000,000 tons, or more, of ore was mined in this manner during a period of about thirty-five years.

Jan 1, 1939

By E. Heikkinen, J. Suikkanen, T. Siren, J. Valli, M. Hakala

Diametrically faced borehole breakout observations are a fairly good indication of magnitude of the secondary stresses acting perpendicular to the borehole. In cases of low in situ stresses, where borehole breakouts are not observed naturally, it is possible to increase the prevailing stress state around the borehole by increasing the rock temperature. When the temperature is increased sufficiently, thermally induced borehole breakouts will occur. By implementing the temperature increase in boreholes located at excavated tunnels, it is also possible to study the effect of the near-field stresses caused by the excavation. The near-field stress state changes as a function of borehole depth, thus increasing the information available from experiment. To study the feasibility of this proposed low cost method, a Borehole Thermal Spalling (BTS) experiment was executed in ONKALO Underground Rock Characterization Facility, in Western Finland in 2014. The first borehole pilot test with the method was conducted in ONKALO at the POSE niche in already at May 2010, with the second pilot test following in August 2010 at Äspö HRL. The major objective of the experiments was to define the trend of the maximum in situ stress component, while also providing knowledge of the in situ spalling strength of the ONKALO rock mass. The stress state in ONKALO is nearly isotropic in horizontal layer, causing problems for the use of more traditional stress measurement methods. With boreholes heated over long interval, the weakest rock parts are observed to fail, thus providing statistical confidence. For these reasons, continuous test sections have an advantage in ONKALO, compared to spatially limited stress measurement methods such as overcoring and hydraulic fracturing. The BTS experiment is conducted in 9 meter deep vertical boreholes located at the POSE niche, situated -345 m depth below the ground surface. The boreholes used within the BTS experiment are located in migmatitic granite, in an experiment area where the surrounding stress state and the rock strength are fairly well known. The prior knowledge of the stresses is favourable for the experiment, as it requires careful planning and iterations to determine the appropriate heating power domain. Too low heating power will not be sufficient to cause borehole breakout, while too high heating power causes breakout in all directions thus making determination of stress direction hard or impossible. The initial state of the borehole and induced borehole breakouts will be monitored using acoustic televiewer logging (ABI) and optical borehole logging (OBI) imaging techniques. Fracture mechanics modelling is used in planning of the experiment, also in back-analysis to link the observed breakout angle to stress state. Both the pilot test in 2010 and BTS test in 2014 resulted in similar borehole breakout direction. The results are in line with so called EDZ & VT1 stress interpretation, revealed the maximum horizontal component bearing the magnitude of 21.5 MPa, with the trend of 166°.

Jan 1, 2015

By J. P. Weiler

The increasing use of high-pressure die-cast magnesium alloys in the automobile industry requires a better understanding of the mechanical properties, the microstructure, and particularly, the relationship between these two. The goal of this study is to first understand the microstructural features which control the mechanical properties observed from an AM6OB magnesium alloy, and second, to be able to predict the local mechanical properties based on microstructural features encountered in different areas of the die-cast component. The two main tools used in this study are spherical indentation testing, used on local areas of the die-cast magnesium alloy AM6OB to detect changes in microstructure and mechanical properties, and X-ray tomography, used to non-destructively investigate the internal porosity in a sample. The results from these tests are then used to predict the local mechanical properties such as the yield stress, the strain-hardening characteristics, and the fracture properties of the AM6OB component.

Jan 1, 2006

The mining industry has generally been slow to apply ion exchange processes to hydrometallurgical applications even if ion exchange offers an ideal solution for a particular problem. Two notable exceptions are in gold and uranium recovery. The largest application of ion exchange in the metals processing industry has been the use of resin-in-pulp (RIP) for gold recovery as an alternative to activated carbon. Iron is a ubiquitous impurity in hydrometallurgical solutions. In many cases, bulk removal of iron from the process solutions is accomplished by precipitation. However, precipitation for iron control is often accompanied by losses of base metals by co-precipitation. Increasingly, the option of ion exchange for removal of smaller amounts of iron from process solutions has been favoured. A number of applications have been developed and proven at the commercial scale for the removal/control of iron from a range of metal processing solutions. This paper provides an overview of the application of ion exchange for iron removal from a range of metal processing operations, including Cu, Ni and Co solutions. A number of case studies are provided which review operational and resin regeneration strategies and the impact upon the commercial operation of metal processing with improved iron control.

Jan 1, 2006

By E. O. Magnusson

THE orebodies of the Preston East Dome mine show a considerable variation in size,? shape, dip, and ground condition. They vary from small and large irregular masses being mined by shrinkage, cut-and-fill, and square set-and-fill mining methods to narrow veins being mined by open stoping. Standardization of mining operations has necessarily been difficult. This considerable variation in mining condition prompted the development of a bonus system which would give more equitable bonus payments through-out the mine than those obtained by the usually accepted methods of calculating mine bonus. PRINCIPLES ON WHICH THE SYSTEM IS BASED Under an incentive bonus system, performance (efficiency) and a price per unit of work done are inter-related. It is in the application of this? principle to working conditions .in the Preston East Dome mine that the system to be described differs from the standard methods of calculating mine bonus. It was found that the method of paying a fixed price per unit of work done, under the 'contract' system, gave satisfactory results in development, less satisfactory results in timbering, and results which were not satisfactory in stoping. Under the fixed price system, bonus payments, in timbering and stoping particularly, were very erratic and did not necessarily represent fair payment for the work done. A fixed price in development is satisfactory because the work done, and the conditions under which the work is done, are uniform. The drilling and blasting cycle is completed in one shift, the size of heading is con-trolled, and a minimum number of holes are required in order to obtain a satisfactory break. The performance possible under these conditions has been found to be confined to a fairly narrow range. By performance in development is meant the efficiency of the working crew as expressed in terms of the two variables of feet of advance per round and pounds of ex-plosives consumed per foot of advance. A change in rock formation, how-ever, may alter to a marked degree the performance possible, quite independent of the skill and energy of the working crew. The changes in working conditions that affect development performance from the standpoint of bonus calculation are usually easily apparent and are satisfactorily met by establishing several fixed prices.

Jan 1, 1944

By H. J. lgner

Hydraulic fills are widely used in the tabular, steeply dipping stopes of the South African gold and platinum mines as an integrated process within a daily cycle of drill and blast. There is therefore only a small time window in which to fill the geotextile bags used as primary fill containment, without the risk of loosing production. Consequently, mines tend to increase the flow rate to the stopes, although this compromises adequate drainage, consolidation and strength development during filling. Recent underground measurements inside the geotextile bag have revealed that at high rates of rise and at 25 degrees dip, the backfill can remobilise within a limited area inside the geotextile bag during filling. This sudden downward surge of backfill exerts, for only a few seconds, additional loading on the geotextile, its supporting mesh and the props. This unstable behaviour poses a serious threat as it can push props out of place, thereby damaging the geotextile bag and causing a mud slide in the stope. To reduce the risk of accidents, the phenomenon of sudden slumping was further investigated for various filling conditions in the laboratory. The results confirmed that the maximum pressures associated with the sudden slumping can be more than five times those experienced during steady-state consolidation. Based on this new insight, the current best practice for hydraulic backfilling was critically reviewed. A practical approach to implementing meaningful standards is presented to ensure safe operations in relation to the consistency of the backfill quality and the appropriate matching of geotextile characteristics with backfill properties.

May 1, 2007

By J. Chelsey Dawson

In presenting a thesis on this subject it is advisable to explain a few of the reasons for its seeming incompleteness. World progress has brought us to a position where approximations are not only to be condoned, but regarded as absolute essentials. Production in anticipation of demand is always accompanied by mistakes on the part of the producers. Only through trial and sometimes erring hypotheses may there be evolved the true course and theory upon which the steady triumphant march of world-wide industry depends. The average person likes to have everything placed ?before him in a clear and convincing manner. It is the impossibility of doing this which, in many cases, arises to confound the writer on shales. All that one can do is to present, as lucidly as possible, the known hypotheses' and theories on the subject and leave the reader to study and work out the truth for himself. Many theories have been advanced on the origin of oil-shales ; some may be correct in certain instances and not in others; however, the writer will attempt no decision as to which are and which are not correct, but .will merely point out the relative merits of each. The figures given for reserves of oil and shale in different countries are only approximations and give but a rough idea of the true conditions.

Jan 1, 1925

By N. Ahern, L. Manoukian

"Cyanide is a leaching agent for precious metals commonly used in gold ore processing. Cyanide exists in various forms (including free, complexed as weak or strong complexes, and as ions such as cyanate and thiocyanate), so its detection, speciation and analysis in processing or environmental samples can be complex. This paper will review best practices for cyanide sampling and preservation in the field, interferences and pretreatment methods required prior to sample analysis and analytical methods that are used for cyanide species. Titrimetric, flow injection ligand exchange, spectrophotometric, colorimetric, potentiometric, amperometric, and chromatography techniques will be discussed and their chemistries, detection limits, advantages and limitations will be described.INTRODUCTION Cyanide is well known to be an extremely toxic species. Accurate cyanide measurement in effluent from mines is critical from an environmental perspective. Its measurement is also an important control parameter in the recovery of gold using cyanidation. Cyanide chemistry is diverse and complex, and cyanide analysis can be challenging as a result of and because of limitations in understanding of analytical methods. Various chemical mechanisms can form or destroy cyanide, and the sample matrix or preservation chemicals can also affect analytical results. These interferences make the collection of reliable cyanide measurements challenging and can start as soon as the sample is collected, during laboratory pre-treatment and during analysis. This paper reviews different methods of cyanide measurement. The basic chemistry of cyanide, best practices for sampling and preservation, as well as various methods of analysis will be discussed.CHEMISTRY The complexity of cyanide chemistry is well known (Beck, 1987; Delgado, Botz, Bucknam, Milasovljevic, & Staley, 2008; Botz, Milosavljevic, & Ward, 2013) and is attributed to the ability of cyanide to undergo: •,Volatilization •,Precipitation •,Adsorption •,Complexation with metals •,Oxidation to cyanate, ammonia, or cyanogen chloride •,Reaction with sulfur or sulfide minerals to form thiocyanate •,Redox reactions leading to the formation of cyanogen and cyanate •,Redox reactions (of some cyano complexes) •,Photochemical reactions (of some cyano complexes)"

Jan 1, 2017

By A. Majumdar, B. Servière, H. Persson

The CCR refinery, which was built in 1931, treats both internal and third party copper anodes to produce 325,000 mt of copper as cathodes. These anodes contain high levels of impurities, such as Ni, As, Sb and Bi, that reports to the electrolyte during the refining step and need to be removed in order to maintain cathode quality and operating efficiencies. In the purification plant, the electrolyte is de-copperized via electrowinning in three stages. In the last stage, the copper content of the electrolyte is reduced to below 1 gpl in order to maximize the co-deposition of As, Sb and Bi with the Cu. This is accomplished with minimum arsine gas generation by using periodic reversal of the current and by controlling the final copper content of the electrolyte. Nevertheless, the possibility of exposure to arsine is treated as a major risk and controls have been implemented to reduce this risk. This paper describes the controls in place at the purification plant, which are being continuously improved through periodic risk assessments and audits. INTRODUCTION The CCR Refinery, which is a part of Glencore Canada Corporation and located in Montreal-East, Quebec, is a custom copper and precious metal refinery, with a capacity to refine 325,000 tonnes of copper anodes per year. Copper anodes are received from the Horne smelter in Rouyn-Noranda, Quebec, Altonorte smelter in Chile and other 3rd party smelters. CCR anodes are produced using the spent anodes from the tankhouse along with purchased spent anodes and copper scrap. The precious metal plant treats the tankhouse anode slime, purchased anode slime, precious metal ingots and Doré anodes from Glencore’s Brunswick lead smelter in Belledune, New Brunswick. CCR products include copper cathodes, silver and gold bullion, a platinum-palladium concentrate, selenium, tellurium dioxide and nickel sulfate. In 1975 an accident occurred at CCR where two employees were exposed to fatal levels of arsine emitted from the then existing purification cells. This process was therefore shut down immediately. Research and development work was then initiated to determine the optimum electrowinning conditions whereby arsine gas generation would be minimized while maintaining high copper and impurity removal efficiencies. It was found that the application of periodic reversal of current (PRC) during the last stage of electrowinning retarded the onset of arsine formation while at the same time allowing the copper concentration to be reduced to less than 1 gpl (Houlachi & Claessens, 1978). A new purification plant was designed based on the PRC technology and was started up in 1976. In addition to the use of PRC electrowinning, the new plant is located in a fully enclosed section of the tankhouse. A special effort was made to design a ventilation system to evacuate the acid mist in addition to any arsine gas. Arsine monitors were installed to measure the emissions from the stack along with arsine levels in the workroom. The arsine monitors and the ventilation system were interlocked with the rectifiers (Thiriar et al., 1983).

Jan 1, 2019

By William M. (Bill) Shaver

"The author will review the early history of shaft sinking as well as focus on the improvements made in shaft design and construction over the last fifty years (1970 to 2019) to predict how shaft sinking will change over the next fifty years and describe what the shaft sinking world might look like in 2070. INTRODUCTION It is a great honour to be one of your keynote speakers for the Fourth International Conference on Shaft Design and Construction being held in Toronto in November 2019. This is one of the opportunities we have to thank the Mining Companies of the world as well as the industries and companies we serve for their support of the mining contracting and shaft sinking business of Canada and the world at large. Many of these companies are represented here today. Without your support many of the innovations we will talk about today would not be possible. We would also like to thank all the companies that work with us in our business including all the contractors and suppliers who provide the various services we require. These include equipment manufacturers, engineering companies, project management companies and suppliers large and small who cater to our every need as quickly as possible. Without all these partners we would not be as good as we are. Many of these companies are our sponsors this week. Thank you from all of us! This is also an appropriate time to pause and think about those Shaft Sinkers we have lost and those who have been injured on our projects around the world. Please bow your head and remember the Shaft Sinkers you have worked with, who did not return home or those who returned home injured. Think about how we can continue the work of making shafts safer every day as we go forward with our projects so everyone goes home to their families safe and sound. Pause for a minute and thank you. The subject matter we have chosen to discuss today is “Shaft Sinking in the Next Five Decades”. How will the work be done, how fast will it be done, what will it cost, and why we think this may occur? It is appropriate to consider this over the next few days with this auspicious group we have assembled. Today, we will look back at all the advances that have been made over the last many years and look ahead to the future to attempt to predict what shaft sinking will look like in 2070. When I look around the room I recognize that many of us will not be around then so we need not worry about being wrong. Suffice it to say that the next 50 years will be very interesting and exciting for the shaft sinking business."

Jan 1, 2019

By Jan E. Nesset

It is just over 100 years since the practice of blowing small bubbles into a mixture of ground ore and water revolutionized the mining industry, resulting in uneconomic deposits becoming highlyprofitable mines, along with the inevitable lawsuits over this new technology called froth flotation. To this day, the viability of many mining projects rests largely with the ability of flotation to effectively capture the valuable minerals and reject wastes. Remarkably, bubble behaviour in flotation has not been well understood until very recently with the advent of new sensor technologies that can be brought directly into the operating plants. This presentation will review the importance to the mining industry of understanding bubbles, highlight these new technologies and illustrate, with examples, how paying attention to your bubbles will pay off.

Jan 1, 2009

By B. A. McKee, T. Adamcewicz

For a capital expenditure of only $46,000, Caland Ore Company has successfully converted its three dry grinding center peripheral discharge rod mills to dry grinding ball mills. The conversion has resulted in a significant capacity increase, operating cost reductions and in-plant environmental improvements. This paper describes why and how• the conversion was made.

Jan 1, 1972

By Nancy E. Wilk

In 2015, more than 1.2 million deaths annually were estimated to be caused by occupational risks (WHO, 2018). In 2021, this estimate increased with the publishing of the World Health Organization (WHO) and the International Labour Office (ILO) Joint Estimates of the Work-related Burden of Disease and Injury based on data from 2000 to 2016 (WHO/ILO, 2021). These global estimates reported that each year 1.9 million people die from exposure to occupational risk factors, 81% of these fatalities resulting from non-communicable, occupational diseases. WHO/ILO notes that the health-related risk factors with the largest number of attributable deaths were exposures to long working hours followed by workplace exposures to particulate matter, gases, and fumes. The health outcome with the greatest work-related burden of deaths was chronic obstructive pulmonary disease, followed by stroke and ischaemic heart disease. In considering the 2021 data published by WHO/ILO, it is likely that the estimates are low and underestimate the true burden of occupational disease and injury. In support of that position, more recently the ILO estimated that “2.3 million women and men around the world succumb to work-related accidents or diseases every year; this corresponds to over 6000 deaths every single day” (ILO, 2022).

Jan 1, 2023

By John Postle, Maureen Jensen, Marcel Vallee, Bernie Haystead, Dan Hora, Graham Clow

The Committee's proposed standards establish definitions and guidelines for the reporting of Exploration Information, Mineral Resources and Mineral Reserves in Canada and are identified as the "CIM Standards" and referred to as such hereafter in this document. To provide additional clarification to Qualified Persons (QPs), guidelines have been included with the respective definitions. The CIM Standards are applicable to all minerals including industrial minerals, diamonds and other gemstones. Reserve definitions for bitumen, natural gas and oil are not included in these Standards. The CIM Standards are not intended to cover mineral inventory estimates that will be reported to government agencies.

Jan 1, 2001

This paper describes the results of a laboratory study on the upgrading of Algoma siderite by the amine flotation of silica and silicate gangue. The experiments indicate that a virtually complete removal of silica is possible in a rougher flotation con-ducted in tap water at natural pH, without prior desliming of the ore. Grinding considerably finer than the apparent liberation size is essential for maximum silica rejection. A cationic collector, Aeromine 3037, gave best results when used in combination with a modifier. Of the several modifiers tested, a Dutch potato dextrin, Dextrin 4356, was found to be the most effective. Both iron recovery and the grade of the final iron product are enhanced by floating the pyrite contained in the ore prior to the amine flotation of the silica, and by scalping the magnetics from the silica concentrate. F OR over twenty years, the Algoma Ore Properties Division of The Algoma Steel

Jan 1, 1963