Search Documents

By M. H. Allan

SASKATCHEWAN POWER CORPORATION is a Provincial Crown Corporation responsible for the production transmission and distribution of electric power and natural gas in the Province of Saskatchewan. Through the electric power responsibility, we became interested in the coal reserves in Saskatchewan, which, although still somewhat of an "orphan fuel" in the early and mid 1950's, gave the promise of providing a low-cost source of energy for electric generation. Coal in Saskatchewan, a lignite with an "as-received" heating value of from 5000 to 6500 Btu's per lb and up to 40% moisture, was first recorded in 1853 . By the end of the 19th century, many small mines were in operation in the Estevan, Coronach and Shaunavon areas supplying local inhabitants with a cheap source of heat. These small mines, some of them prosperous, some of them not, continued operation right up to the late 1940's, when oil replaced coal in the market place. The year 1930, however, saw the introduction of the new technique of strip mining in the Estevan area. This technique revolutionized coal mining. It was now possible to use large machinery to uncover the coal and cast the overburden to one side instead of burrowing through thin seams of coal varying from 2 to 10 feet thick. The overburden cast aside by these large mechanical shovels, or later draglines, created heaps of spoil which at that time, during the depression, were a sure sign of prosperity and the welcome news that people had jobs. By the late 1940's, coal production had dropped off, but the spoil piles remained and were now labelled by some as "scars on the landscape", even though there had been some natural succession of grasses. In addition, some people had planted trees in experimental plots and even some aerial seeding had been done.

Jan 1, 1978

By Zhiyang Long, Ruiling Xiao

"A mine shaft is one main development method of establishing access in an underground mine. The construction technology of the mine shaft sinking is complicated and large equipment setup on surface and in the mine shaft. The paper briefly reviews a single-line operation method, parallel operation method and mixed operation method as well as the features of the one operation method with the excavation, lining and installation. The special construction technology mainly would include ground freezing methods, full diameter shaft drilling methods, caisson methods, grouting technology and concrete curtain methods as well as other methods. The paper summarizes the shaft sinking numbers and effects by the special construction methods during different periods. The paper states the shaft sinking conditions and the each created record conditions in the coal, metallurgy, non-ferrous metal, hydropower, highway, railway, nonmetallic and other industries. The paper has a prediction on the shaft sinking requirements and development tendency in the future for China.INTRODUCTIONA mine shaft is one main development method of access in an underground mine. In recent years in China the new shaft mines represent 45% of the total number of new mines. With the development of new mining area under construction and the development of deeper mines, the ratio of the mine shaft as access for underground mines will increase. The construction technology of the mine shaft engineering will be complicated, the operation site footprint will be small and the working environment will be more difficult. The mine shaft sinking operation will often be varied by the geological conditions and affected by underground water inflows, seam gas outbursts, geothermal and other natural conditions. The safe construction of the mine shaft sinking will be challenged by all these conditions. Although the mine shaft engineering will only be about 5% of the total mine roadway engineering, the mine shaft construction period often will take over 40% of the total mine construction period. With the progress of modernized mine production technology and the construction of a high production and high efficient mine, the mine transportation roadways mostly would be set in the seam and the engineered amount of the mine rock roadways reduced year by year could cause more prominent long extensions of the mine shaft construction period. Therefore, in order to speed up the construction, to shorten the mine construction period and to realize the investment benefits as early as possible, the technical level of the mine shaft sinking should firstly be improved and the construction speed of the mine shaft engineering and sinking should be speeded up, which would have important significant benefits."

Jan 1, 2019

By J. E. Gill

THE 1938 season was marked by a distinct lull in exploratory activity in the Province of Quebec. Quebec was not unique in this respect, but the condition appears to have been more acute here than in most other parts of the Dominion. Various causes may be suggested to account for this. The general disturbance in political and economic conditions throughout the world has certainly had an adverse influence. Uncertainty induced by changes in the mining laws of Quebec in 1937 contributed. A third cause was the belief, now held by many, that the easily accessible deposits in the main producing belt extending eastward from. the Rouyn district have now all been found and that new discoveries in this field will henceforth come more slowly and more expensively. A fourth is the lack of conspicuous success by companies and individuals who have interested themselves in less accessible areas to the north, notably the Chibougamau district. A fifth, the unattractive appearance, as viewed on published geological maps, of the vast area extending northward to Ungava bay and Hudson strait. A sixth, the attraction of such speculative funds as were available to the Northwest Territories, where spectacular finds were reported in the fall of 1937. Whatever may be the relative importance of these causes, languor in exploration will ultimately be reflected in production returns. This appears, therefore, to be an opportune time to take stock of the general position of the Industry in the Province and to consider ways and means of counter-acting those conditions which are now impeding, or will in the near future impede, its expansion. At the request of the Institute Secretary, Mr. Carlyle, I have prepared a brief summary of accomplishments to date and a discussion of some of the geological aspects of the problem.

Jan 1, 1939

By Charles G. Kemsley

IN view of the truly remarkable development of special steels for special purposes, the mining industry has for years looked forward to a time when steel makers would come forward with a product which would be an improvement over the straight carbon steel which has always held the field for drilling rock. In order to avoid making changes in conventional shop practice, the industry has perhaps been too insistent upon obtaining a water hardening steel which could be handled in the blacksmith shop by long established methods. As early as 1932 or 1933, an oil-hardening tool-steel of the one per cent carbon, plus chrome, plus molybdenum type was applied to hollow drill steel. It was known as a hard as well as a tough steel, and one that, theoretically, should give a good account of itself as a rock drill, if properly heat-treated; and so it has proved in actual trials. There were numerous deterrents which retarded adoption of this steel. For several years there has been a constant improvement in the drilling qualities of the straight carbon steel, and, considering the higher unit price ? of the alloy, there has been considerable doubt in the minds of some mining? men as to what advantage there might be in the use of alloy over straight carbon for hollow drill steel. The alloy being an oil-hardening steel, its adoption meant having two kinds of steel in the mine, for a time, and that spelled trouble, unless some positive means of identification was adopted. The hardening and forging ranges of alloy steel being narrow also made necessary much closer control over these operations if poor results were to be avoided. These thoughts undoubtedly prevented its use becoming wide-spread, for, as a matter of actual record, less than fifteen per cent of all the hollow drill steel used in Canada today is alloy.

Jan 1, 1942

By E. P. Wiechrnann, C. M. Castro, G. A. Vidal, F. A. Muñoz

Different authors and publications indicate that Optibar Segmented Intercell Bars cause a remarkable distortion in the distribution of the current in a cell group. However, these results were based in inaccurate computer based models and do not represent the technology. During the last trimester of 2010, a 92 cells circuit from Barrick Zaldívar EW plant was implemented with Optibar Segmented Intercell Bars. The technology was incorporated progressively without disrupting the plant production. Depending on operational conditions, this led to a 2 to 4% current efficiency increase and 3 to 5% specific energy consumption reduction. By October 2011, 40,000 tons of copper will be produced with the technology.

Jan 1, 2011

By H. W. Leon, F. J. Ellis

"This paper covers the new six-strand curved-mould billet casting machine at the Contrecoeur Works of SidbecDosco. It commenced production of 3 Yz-in. square billets at the beginning of January 1972. Together with two 100- ton ultra-high-power electric furnaces in a new meltshop, it is the principal source of billets for the existing rod and bar mill also located at Contrecoeur. The paper develops the reasoning for casting-to-size 3Y2 -in. billets and for choosing a six-strand machine. It indicates the significance of Sidbec-Dosco Montreal Works' extensive experience in operating a four-strand curvedmould billet machine since 1965 and the ways in which this experience influenced the design and operation of the new caster. Machine features are described in detail, as are the reasons for some of the features. The installation, checkout and crew training are briefly discussed as well as the tundish teeming trials. The first cast on January 5, 1972, is covered and a log is shown of the first casts to an empty ladle. There are operating statistics covering the first 100 casts, which produced 8000 tons of good billets in ten weeks of operation. Machine performance and billet quality were good and the few minor problems encountered are described."

Jan 1, 1973

By Lawrence D. Hoy, Armand Savoie, Pierre Trudel, Ghislaln Tourigny, Robert Crépeau, Lao Kheang

"Recent fluid inclusion and stable isotopic studies in the Bousquet mining district have identified spatial and temporal trends in mineralization temperatures and isotopic compositions of vein forming fluids. These studies indicate that mineralizing temperatures were lower during sterile vein formation (T=200-300°C) than during auriferous vein formation (T = 300-400°C), and that 8 80 values of minerals in sterile veins are lower by 1-3 %o than in associated auriferous veins. In addition to these small differences in 8 80 within individual mineralized zones, a trend of increasing 8 80 values of vein minerals is identified from west to east across the district, with 8 80 of vein minerals increasing by4-6%o. Quantitative evaluation of potential causes of the observed oxygen isotopic shifts suggests that the best explanation for these trends is the derivation of the mineralizing fluids from an isotopically inhomogeneous terrain in which the fluid isotopic compositions are controlled by the isotopic compositions of the host lithologies due to high rock/water ratios in these source terrains. This inhomogeneous source terrain is interpreted as consisting of the Blake River Group volcanics (low 8 80 component) and the adjoining Kewagama and Cadillac Group sediments (high 8 80 component).The genesis of the hydrothermal fluids is attributed to crustal heating during metamorphism, with the fluids representing metamorphic dewatering products and/or fluids incorporated during deposition and burial of the host lithologies. Ductile deformation of the fluid source regions impeded fluid migration during metamorphism; the ultimate release of the mineralizing fluids is attributed to the penetration to depth of vertical structures (fault and shear zones) during brittle deformation of the crust under waning metamorphic conditions. Release of fluids caused by this puncturing of the closed hydrologic source regime produced a localized zone of lowered pressure, drawing fluids from adjacent lithologies toward the fault zones, feeding further hydrothermal fluid upwelling. Au mineralization resulted from chemical processes related to cooling of the hydrothermal fluids and/or interaction with lithologies encountered during fluid migration; the level of crust at which Au deposition occurred likely migrated upward with the thermal anomaly caused by hydrothermal fluid upwelling, eventually reaching the level of current exploitation. Cessation of fluid flow along the vertical structures is attributed to inadequate recharge of the hydrothermal systems as fluid contents were depleted in the lithologies proximal to the vertical structures and/or sealing of the structures by mineral deposition."

Jan 1, 1990

By Penny C. Stewart

Narrow vein underground stope design engineers in Australia have expressed significant interest in the requirements and methodology for developing site-specific stability charts. This is largely due to a concern that existing stope stability charts inadequately take into account factors influencing narrow vein stope stability, such as the effect of backfill abutments and the effect of in stope pillars. This paper presents conclusions from a comprehensive statistical examination of case history requirements for a site specific stability chart and critiques literature arguments for site-specific charts. A new statistical analysis technique and a large comprehensive stability database enabled the authors to quantify case history requirements and any site-specific effects the model exhibits. The analyses indicated that a reliable stable-failure boundary requires at least 150 case histories, of which a minimum of 10 percent should be unstable stope surfaces. Marginal site-specific effects were observed for the operating conditions captured within the database. The authors conclude that the apparent site-specific effects noted in previous literature are attributable to operating conditions inadequately represented in the database. Such operating conditions could induce erroneous stability predictions at any site, and are therefore not truly site-specific. Following from these conclusions, a strategy for taking into account operating conditions particularly relevant to narrow vein mining has been proposed. In particular, the development of a chart that accounts for the effect of backfill abutments on stope stability. Backfill abutment effects are particularly relevant to mechanised narrow vein mining methods such as modified Avoca. Collaboration from at least five sites is required to obtain access to relevant data and underground drives for geotechnical mapping. Preliminary estimations indicate that approximately three months fieldwork is required to meet case history requirements. CMS data in conjunction with 3-dimensional design software will be used to calculate equivalent linear overbreak/slough (ELOS). In contrast to stable, failure, major failure and caving categorical variables, ELOS is an objective and continuous stability variable and is therefore, more conducive to mathematical modelling.

Oct 1, 2001

By Benoit Bissonnette, David Gelderland

"The Campbell Mine Constructed Wetlands has been in full operation, processing effluent from the water treatment plant of the mill circuit for the last two years.The overall results are extremely positive with dramatic improvements for the originally targeted parameters – Ammonia, Copper and toxicity.• Ammonia concentrations were reduced from an average of 5 mg/L to an average of 0.43 mg/L which translates to an average reduction of 91%.• Copper concentrations were reduced from an average concentration of 0.054 mg/L to an average of 0.019 mg/L, which translates to an average reduction of 65%.• LC50 Acute toxicity testing revealed no impact.• IC25 Chronic toxicity tests revealed no impairment to growth or reproduction.As a result of the improvements in discharge water quality from the wetland, 100 percent compliance with respect to all Certificate of Approval, MISA and MMER regulations for effluent will be consistently achieved.The system has proven to be very easy to operate and maintain, with a minimum of care. Given some basic rules are followed, the construction of the wetlands was straightforward and relatively inexpensive compared to other treatment methods.The ecological benefits of the operation of the wetland are also quite substantial, as is the positive image of the corporation in environmental stewardship.INTRODUCTIONOver the last four years, Campbell Mine has adopted an aggressive schedule for the development of wetlands for use as the final stage of effluent treatment within the tailings management facility. The focus of this work has been to utilize natural biological systems to provide Campbell Mine with a 100 percent compliant water quality with respect to all MISA, MMER and COA discharge criteria at all times throughout the effluent discharge period."

Jan 1, 2003

By W. Torres Pino, L. Mariscal Samaniego

The Ilo Smelter has been continuously operating since 1960 with Reverberatory furnaces and Pierce Smith converters producing blister copper. The original installed capacity of 1.134 tons per day of concentrated was expanded in 1976. A process of modernization started in 1995 and 1998 with the installation of an El Teniente Converter, a sulfuric acid plant and an oxygen plant to reduce the gaseous emissions to the atmosphere. With the official approval of the Environmental Compliance and Management Program (Programa de Adecuaci6n y Manejo Ambiental - PAMA) in January 1997, Southern Peru Copper Corporation made a commitment to capture 91. 7% of the S02 generated at the smelter by January 2007. After an evaluation of six different technologies, the ISASMEL T process was selected because it can be easily adapted to the present operation, has a lower capital cost and it is a simple process. The fast learning curve to reach the total capacity will allow to fulfill the PAMA commitment in time. The project construction is in process and SPCC is prepared for a successful start-up and transition of the current operations at the end of year 2006. This paper outlines the factors considered by SPCC in its choice of ISASMEL T technology and describes the construction and the start-up activities of the new facilities.

Jan 1, 2007

By A. Aaltonen, S. Paloranta, H. Myllykangas

A property based dynamic model of flotation was built and validated for training purposes. The model is based on the work of the AMIRA P9 project. The recovery of each particle with composition and size is calculated in a given simulation step. The model takes into account machine and operational parameters such as air flowrate and froth height. The model was created using fullscale test data on Pyhlisalmi Cu-Zn-pyrite ore with flotation kinetics of multiphase particles determined. Simulation and validation shows that model can predict the dynamic behavior of the process accurately enough for training purposes.

Jan 1, 2009

By Michel Massé

Eleonore Project- Agenda ? Purpose and Technical Overview ? SmartEXEC Control Capabilities ? SmartEXEC System Archetecture ? SmartEXEC System Advantage Eleonore Project- Purpose and Technical Overview ? Control air quality while maintaining target production levels at minimum energy operating cost ? Improve safety, work place conditions and operation flexibility ? Reduce energy consumption and green house gases footprint

Aug 1, 2013

By George R. Elliott

Introduction The pages that follow present a brief chronological survey of views which have been held, and of legislation enacted, for the regulation of the natural gas and oil industry in the Turner Valley field, especially as regards conservation of the natural gas. To provide a necessary background for an adequate understanding of the progress of events in western Canada, there is included also a compilation, from technical and legal authorities, of some of the more important measures which have been adopted for the regulation of the oil and gas fields of the United States, where these measures have had, or are likely to have, a bearing on the course of our domestic industry. Owing to exigencies of space, it has been possible to refer only to the most outstanding proposals and legislation, and to these in the briefest possible form. Although, so far as Canada is concerned, the data presented are restricted almost entirely to the Turner Valley field, it is the hope of the writer that the paper may prove of value for purposes of reference: for any similar gas and oil fields discovered in western Canada will certainly revive and intensify the problem of the proper steps to be taken for the conservation of the gas. Definition of 'Conservation The term conservation has been so misunderstood and misrepresented that, to many persons in Alberta, it means little more than closing-in wells. In the light of the definition of Charles E. Hughes, that 'True conservation of a raw material is its economical use', the subject of natural gas conservation is inseparably involved with the study of the function of the -gas and with the development of the principles of unit operation.

Jan 1, 1934

By Fr. -W. Bach

In the past years the enormous weight saving potential of magnesium sheet has been demonstrated by various research projects all over the world. It has been shown magnesium flat products can benefit automotive, aviation, machine tool and consumer electronics industries. Major material problems such as poor formability, corrosion resistance and high production cost still inhibit the application of magnesium sheets in large scale production. The present contribution outlines achievements in casting and rolling technology. The authors developed an adapted strip casting process in which near-net-shape rolling feedstock of several wrought alloys has been produced. During the rolling process, various parameters were varied in order to modify the microstructure and surface quality of sheet. Several temperature cycles, strains, lubricants, roll surface structures and roll coatings have been analyzed. The sheets were examined and tested in deep-drawing experiments. Suitable rolling schedules have been developed for standard and modified wrought alloys. The study concludes with an overview of current industrial solutions and an estimation of the potential cost savings that might result from the adaptation of the process that has been developed.

Jan 1, 2006

By M. Maeda, H. Sasaki

"Precious metals such as platinum, palladium, and rhodium are commonly used for automotive catalyst converters. To recover these metals with lower environmental load and cost, exposure to zinc vapor was proposed as a pretreatment prior to acid leaching. Alloying with zinc is expected to enhance dissolution of precious metals and reduce the amount of toxic chemical agents required for the leaching. This study examined the effect of the alloying pretreatment using model catalysts. Catalysts were immersed in leaching solutions for a predefined time with or without zinc vapor pretreatment, and the amount of dissolved metals was then evaluated. INTRODUCTIONAutomotive catalysts account for large portions of the world consumption of platinum (Pt), palladium (Pd), and rhodium (Rh) (Butler, J., 2011). Because of their limited production and high prices, recovery of the precious metals from spent catalysts is obviously an important issue. A representative structure of an automotive catalytic converter can be described as a monolithic ceramic support with a honeycomb structure which is coated with porous oxides such as those of aluminum (Al2O3), cerium (CeO2), and zirconium (ZrO2) (Heck & Farrauto, 2001; Matsumoto & Shinjoh, 2007). Small particles of precious metals, originally several nanometers or less, adhere to the oxides.Typical recovery processes for precious metals from scraps are shown in Figure 1 (a)-(c) (Habashi, 1997; Yoo, 1998; Shibata & Okuda, 2002). Precious metals can be recovered by using non-ferrous smelters as Figure 1 (a) shows. Smelted along with metals such as copper (Cu), precious metals and ceramics in the scraps are absorbed into the metal phase and slag phase, respectively. Because the metals separate from Cu as anode slime in successive electro-refining, such a process can recover precious metals as co-products of Cu. However, in order to prevent negative effects on the principal process, a specialized procedure is needed. Figure 1 (b) is a specialized approach in which scraps are melted at elevated temperature with Cu called the Rose process. Here Cu works as a collector metal, and the absorbed precious metals are then concentrated by oxidation of Cu. Such a process can separate precious metals from ceramics constituting catalyst converters. Smelting at high temperature, however, requires extensive equipment as well as a high amount of energy. On the other hand, hydrometallurgical processes may be effective to separate precious metals from ceramics into an aqueous solution, because chemical agents can act on these metals selectively (Figure 1 (c)). Leaching of precious metals, however, requires strong acid and oxidizing agents because of their corrosion resistance; this makes liquid waste disposal and the large environmental load controversial. To solve the problem, a metal vapor pretreatment was proposed (Okabe, Yamamoto, Kayanuma, & Maeda, 2003a, 2003b; Kayanuma, Okabe, Mitsuda, & Maeda., 2004; Kayanuma, Okabe, & Maeda, 2004; Itoh, Kayanuma, Miyake, Kimura, & Maeda, 2005). A flow diagram of the process using zinc (Zn) vapor is shown by Fig. 1(d). Exposed to Zn vapor, precious metals are expected to form alloys which dissolve more easily than pure precious metals, thus reducing the use of chemical agents and environmental load involved with successive leaching. In previous research (Sasaki, Miyaki, & Maeda, 2010; Sasaki & Maeda, 2010, 2012), dissolutions of precious metal alloys formed by Zn vapor treatment were examined in hydrochloric acid (HCl) using an electrochemical method, and it was confirmed that these metals dissolved at higher rates from the alloys than from their pure states (Figure 2). In this study, the availability of the alloying pretreatment was demonstrated by testing on model catalysts in leaching solutions."

Jan 1, 2012

By P. H. Jennings

Commercial tellurium commonly contains heavy basemetal impurities such as lead, copper, iron, etc., as well as selenium and oxygen. The base metals may be removed by vacuum distillation or by zone melting. Vacuum distillation is a convenient method for treating moderate quantities (~ 100 kg.) for the production of a material having a total content of heavy metals in the 10-30 ppm range. By zone melting, it is possible to lower all the heavy metal impurities tm below the limits of spectrographie detection. Neither vacuum distillation nor zone melting is effective for the removal of selenium, but treatment of molten tellurium with hydrogen converts selenium to hydrogen selenide. This procedure is too s low to be considered except as an adjunct to zone melting. In the course of air-melting, many of the more easily oxidized impurities form a dross and may thus be readily removed. Substantial refinement with respect to iron, tin, chromium, aluminum, sodium, silicon, magnesium, calcium and manganese can be achieved in this way. Although tellurium can be electrodeposited from either acid or alkaline solutions of the dioxide, various factors militate against successful electro-refining, amongst which may be mentioned the brittleness of cast tellurium anodes and the tendency for the metal to be deposited in dendritic form, even at low current densities.

Feb 1, 1966

By V. Vorontsov

Catalysts Mo-Ni-S were prepared by combining MoS2 and NiS in weight ratios 1:1, 1:2, 1:4 and 2:1, each of which was admixed with 5%wt Ag and 5%wt YSZ to increase three-phase boundary surface area of the electrode. For comparison catalysts comprising Co-Mo-S in weight ratio of 1:1 of CoS to MoS2 admixed with 5%wt Ag and YSZ and pre-sulfided NiMoO4 were made. The catalysts were examined for electrochemical oxidation of hydrogen sulfide in solid oxide fuel cells (SOFC) at 850°C temperature. The catalyst prepared from 1:1 (wt. %) NiS:MoS2 demonstrated highest performance. Current density up to 1,330 mA/cm2 and power density up to 300 mW/cm2 were achieved using pure H25 gas, which are the highest among the reported H2S-powered fuel cells ever published in the literature. Anode materials of different NiS:MoS2 ratios have been characterized by means of X-ray diffraction (XRD), simultaneous TG/DSC analysis and Neutron Activation Analysis (NAA). TG/DSC and NAA results show that addition of NiS and Ag increases fuel cell performance due to improved structure/integrity of the anode. It has also been demonstrated that MoS2 is a suitable anode material in H2S-powered SOFC, with high activity towards H25 oxidation and thermally and chemically stable up to 850°C.

Jan 1, 2005

By I. Soosaiprakasam

This work investigated inhibition performance of copper carbonate (CuCO3), which is less toxic than conventional heavy-metal corrosion inhibitors in amine treating plants, The investigation was experimentally carried out in a bench-scale electrochemical corrosion cell under an atmospheric pressure, The inhibition performance of CuCO3 in an aqueous solution of monoethanolamine (MEA) was examined under a wide range of operating conditions and reported as a function of process parameters including inhibitor concentration, temperature and solution velocity, The results show that CuCO3 functions as an anodic inhibitor. The addition of CuCO3 decreases corrosion rate of carbon steel but might induce pitting corrosion/

Jan 1, 2005

By G. B. Harris

In recent years, increasing attention has been focused on the hydrometallurgical treatment of base metals feeds, especially nickel laterites and polymetallic sulphides. One approach that has received some attention is the use of high?concentration chloride solutions (brines), which are now showing some promise after initial setbacks. Iron is usually the major component in the base metal feed to such processes, and if physical means cannot be used to remove it, then the iron concentration in the pregnant leach solution is always significant. This paper presents some of the background theory on the hydrolysis of iron in high-strength (>3M) chloride brines, and discusses the roles of temperature, solution concentration and free acidity. It is shown that the system is complex, but that crystalline and readily-filterable hematite can be generated, and that the system has a low energy requirement.

Jan 1, 2006

By Daniel Hodouin, Claude Bazin

"A graphical method to assess the size reduction by grinding is presented and illustrated with data collected from laboratory grinding tests and industrial grinding circuits. The method lies between the graphical comparison of size distributions and the population balance model. The method is easy to apply and provides a quick way to compare grinding mill performances under various operating conditions and processed ores. The application of the method to industrial mills shows that a grinding mill operation could present an invariant behaviour that can be exploited for simulation purposes.INTRODUCTIONThe size reduction of particles by grinding has been studied for decades and several books were published on the subject. Most of the recent studies focus on the modelling of the ball, semiautogenous and autogenous grinding mills operation (Napier-Munn et al., 1996) because accurate simulators can be used for design, optimization and control. Although the development of realistic simulators is progressing, the trial and error method is still used by many operators to identify optimum operating conditions for a grinding machine.Laboratory tests allow the characterization of the material submitted to grinding and the analysis of various operating conditions, such as ball size or shape, mill speed and slurry concentration of solids, on particle size reduction. Similar tests can be conducted in a plant, but results are often difficult to analyze due to errors associated with sampling and sensor accuracy. This paper presents a graphical method to assess the degree of size reduction carried out by a grinding machine. The paper consists of three sections. The first section describes the method and the following sections illustrate the method with data taken from laboratory and industrial grinding machines."

Jan 1, 2004