Search Documents

By Charles G. Kemsley

IN January, 1939, Dome Mines, Limited, purchased a few bars of an alloy drill-steel for the purpose of testing its fatigue resisting qualities as compared with those of a straight carbon-steel then in general use at the mine. A steel of the following analysis was selected: Carbon 1.00% Sulphur 0.022 Chromium 1.26 Silicon 0.17% Phosphorus 0.028 Vanadium 0.1 Manganese 0.32% Molybdenum 0.30 This steel has a tensile strength of 180,000 lb. per square inch and a Brinell hardness of 380, as compared with a tensile strength of 114,000 lb. per square inch and a Brinell hardness of 230 for the standard carbon drill steels, in the as rolled' condition. The result of this test showed that about five times as many runs could be obtained from the alloy steel before failure from fatigue. It was therefore decided to replace gradually the one-inch quarter-octagon carbon steel, then in use, with seven-eighths quarter-octagon alloy steel. In January, 1940, six machines was placed on the seven-eighths steel and this was gradually increased until now (March 15th, 1941) fifty per cent of the steel being used is alloy steel. An O'Donovan furnace is used at the Dome for heat-treating their carbon drill-steel. In this furnace, a magnet withdraws the steel when the critical temperature has been reached, and the operator then places the steel in the quenching tank. Not being able to use this furnace for the alloy steel, the management felt that some means should be developed to determine the quenching temperature without depending upon the operator's judgment of the correct 'colour'. With the assistance of the Canadian General Electric Company, a radiation-type vacuum thermocouple pyrometer was adapted to this purpose, with excellent results; in fact, with this instrument no previous experience in hardening is necessary and results are remarkably uniform.

Jan 1, 1941

By M. K. Jain, Z. T. Xu, M. Bruhis, V. Hegedekatte

"Strain rate and temperature dependent deformation conditions are present during elevated temperature forming of aluminum and other metallic materials. While many constitutive laws have been proposed to represent such deformation conditions, a closer investigation often reveals their limited applicability in terms of fit to the experimental data, and interpolation within and extrapolation outside of the range of experimental stress-strain curves. This is often because material-specific primary deformation mechanisms of temperature-dependent strain and strain rate hardening are poorly captured. In the present work, the Voce-Kocks constitutive model based on mechanics of dislocations storage and annihilation has been found to be suitable for many metallic materials. The model was modified to include the effect of temperature dependent shear modulus. The modified model is then employed to represent the experimental data obtained from uniaxial tensile tests on AA7075-O sheet at elevated temperatures and strain rates. Also, hot gas bulging tests were conducted to verify the applicability of this model. Further, finite element simulation of the hot gas bulge test was performed by incorporating the model as a user material subroutine. Good general agreement was observed between the experimental and FE model predicted results. Some sources of discrepancy in the prediction are also discussed.INTRODUCTION There has been much interest in light-weighting of automobiles from automotive related industries to reduce overall carbon footprint and increase energy efficiency of the vehicles. Aluminum alloys, and especially the medium-strength 5xxx and 6xxx series alloys, have been the primary focus in the last 3 decades to reach the above environmental goals (Huo, Hou, Zhang, & Zhang, 2016) whereas aerospace industry has traditionally focused on high strength 7xxx series aluminum (Al-Zn-Mg-Cu) alloys for structural components (Deng, Yin, & Huang, 2011). Recently, there has been much interest in high strength 7xxx series aluminum as a replacement for heavier steel automotive structural parts such as A-pillar, B-pillar, side impact beams etc. (Harrison & Luckey, 2014). This is both interesting and challenging since the above aluminum structural parts will need to not only meet impact safety standards but also possess sufficient formability for manufacturing such complex parts. Since the formability of high strength 7xxx series materials is quite poor at room temperature, much interest has focused on improving both formability and final part strength via high rate hot stamping, in-die quenching, and subsequent artificial ageing process steps (Kumar & Ross, 2016)."

Jan 1, 2018

By V. Fiedler, H. Lachmund, R. Bruckhaus

"After producing some 50 million tonnes of crude steel the two BOF vessels at Dillinger Hüitte steel plant had to be replaced in 2000/01 due to large deformations. The new vessel design was optimised after a number of theoretical evaluations.Refractory investigations were carried out as well as temperature measurements of the shell to provide a basis for selecting a suitable steel grade. This was found in a DH-GTS development - P420M HT - with high strength at elevated temperatures and excellent weldability and made it also possible to build the vessel without any cooling system.After putting the first vessel into operation the metallurgical results showed no remarkable improvement compared to the old vessel, and were therefore not satisfying. With the help of cold model investigations the arrangement of the tuyeres was modified to improve the flow conditions and the interactions between oxygen jet and the heterogeneous plume of the bottom stirring gas. Further optimisations were obtained by a variation of lance tips and a newly developed lime addition model."

Jan 1, 2004

By G. P. Gu

The in-service 90/10 cupro-nickel tubes in a water-chiller system suffered from severe corrosion damage during their relatively short service life causing unexpected down time. In addition to downtime, the environmental risk associated with losing refrigerant was also a concern that initiated this investigation, Microstructural investigation using SEM and electron microprobe indicated that pitting corrosion had resulted in local nickel depletion, During the corrosion process, copper appeared to have re-deposited around the corrosion pits accelerating the local corrosion.

Jan 1, 2005

By E. B. Spice

"IntroductionExperience at Eldorado has been gained with a variety of mill feeds. That is, the actual mode of occurrence of the pitchblende varies to such an extent that gravity concentration has at times been decidedly unattractive and at others highly successful. Because of this, the type of ore necessary for economic recovery of pitchblende have become well known. Also, those types which do not lend themselves to gravity concentration have become familiar. In general, it may be said that when the pitchblende occurs free, to a large extent, from sulphides or arsenides of high specific gravity, and when the bulk of the pitchblende is localized rather than disseminated, excellent recoveries, high ratios of concentration, and good grades of concentrates , will result from proper gravity concentration. On the other hand, if the ore contains pitchblende intimately or otherwise mixed with large quantities of arsenides or sulphides, or if the pitchblende is finely disseminated, gravity concentration alone will yield high recoveries only at the expense of very low-grade concentrates and low ratios of concentration.According to Taggart, the ease with which gravity separation may be effected is determined by the value of the following ratio: []It is stated that when the ratio is above 1.75, gravity separation can be expected to be easy. Thus with pure U308 (S.G. over 9) and gangue consisting chiefly of siliceous material, the process can he expected to be entirely successful even when carried on at very fine sizes. Unfortunately, the term pitchblende covers a great diversity of material. Although some of the mineral occurs pure enough to have a specific gravity of about 7, the average is much lower than this and is probably well under 5. Some of the pitchblende particles have a specific gravity so low that gravity concentration fails completely. It may also be said that no degree of grinding will produce free pitchblende of sufficient density from such particles. This, then, represents the most important limitation to the application of gravity separation to pitchblende ores."

Jan 1, 1950

Agenda ?Trends in Wireless Technology ?Success and Opportunities ?Improving plants efficiency ?Improving plants reliability ?Improving plants safety and security ?Wireless Ecosystem ?Lessons Learnt / Recommendations Why Wireless? ?Lower cost (no wiring cost) ?Flexibility (no wire) ?Standards-compliant wireless devices major factor enabling growth:?Standard WLAN (IEEE 802.11)?Wireless field I/Os (IEEE 802.11, ISA100.11 and WirelessHART) ??Wireless adoption will become a milestone that will rival the introduction of Fieldbus and the distributed control system (DCS) in its importance.? ARC Advisory Group

May 1, 2009

By James H. Cobbs

Blind boring of shafts is becoming an increasingly important part of shaft sinking. Blind-bored shafts have reached diameters of 25 It in Europe and 16-1/2 ft in the United States. Much of the technology developed for blind boring has evolved from the technology of drilling wells for oil and gas production. Blind boring offers economic advantage in a number of situations where conventional shaft sinking either is extremely difficult or very expensive by virtue of large-capacity aquifers which must be penetrated, unstable ground or where very rapid sinking is required. In sedimentary rocks, blind boring is cost competitive with conventional sinking, in diameters of about 12 ft or less. Blind boring is not competitive with raise boring where conditions are favourable for raise boring. Blind boring does, however, offer greater flexibility than raise boring and can be performed in situations where raise boring is inefficient or impossible. Combination machinery has been developed to perform both blind boring and raise boring, so that the machine can be used effectively in situations where only the near-surface portions of the shaft are unfavourable for raise boring. Development work is being supported by the United States Bureau of Mines for blind boring equipment capable of boring shafts up to 30 feet in diameter.

Jan 1, 1979

By J. Hu, F. Lin, R. Chen, F Peng, S. Yang, W. Yu

"Microseismic monitoring technology has become one of the most effective method of mine ground pressure monitoring after decades of development. But safety assessment of mine ground pressure by using microseismic monitoring is still in the development stage, it needs to be perfected continuously in practice, and choose the optimal assessment indexes and methods. The definitions and physical meanings of wave velocity, b value, and EI-VA value are introduced in this paper. Statistical calculation of the microseismic events in Luomu Mine is finished by using these indexes, then the functions and calculation results of V, b value, and EI-VA value with the variable of time are also given in the paper. The preliminary safety assessment method is established in Luomu Mine, and it has achieved good results in practical application.1.1 Engineering background The Luomu Mine is a super large molybdenum and tungsten production base in China, ore reserves is up to 2 billion tons, first in Asia and third in the world. It begins mining since the 1960. and bases on underground mining until 2002. In order to recover resources more effectively, it began to use opencast mining method and formed a production of 30000t/d in the early 1990. After about 30 years of underground mining, a large mined out spaces was formed under open pit mine, up to area of 1.2 million m2 and volume of 18 million m3, as shown in figure 1. The large number of mined out spaces seriously affects the normal production, mining and handling of mined out spaces are in the high risk. In the past years, several rock mass collapsions happened, and it caused a serious security threat to persons and equipments. According to the distribution characteristics of mined out spaces, Luomu Mine is divided into A, B, C, D and E mining area. The stability of D mining area is studied in this article. D mining area mainly includes 1376,1350,1340,1317 mined out spaces and 1280 deep large mined out area, as shown in figure 2. The mined out spaces of D mining area is extremely complex and high-risk. Therefore, a microseismic monitoring system was built to monitor the stability of D mining area, a large number of valuable datum has been obtained, and it has a striking effect (Cheng & Peng, 2013; Peng et al., 2013)."

Jan 1, 2015

By C. Gravel, A. Fathi, P. Rivard, G. Ballivy, Z. Moradian, M. Quirion

Numerous schemes have been proposed in the past to evaluate the shear strength of rock discontinuities based on in situ and laboratory testing. Due to scale effects, in situ testing is the most reliable way to assess the shear strength parameters. However, practical reasons often impede this kind of testing. This is unfortunate because advances in theoretical rock mechanics are still dependant on qualitative experimental works. This paper presents a mobile high capacity shear apparatus developed for in situ direct shear testing of discontinuities along with testing methodology. The apparatus has the advantage of being simple, although of high capacity, and can be moved to different site locations for other tests. The in situ test was performed on a natural rock outcrop of schist with subvertical schistosity. A concrete block 50 x 50 cm with a base layer of high strength mortar was cast on the rock surface. Prior to the test, the concrete block was lifted and repositioned to have an unbonded joint but with interlocking asperities. The shear load was applied perpendicularly to the schistosity direction. The test was conducted in a constant normal load (CNL) condition. Both normal and shear loads were applied manually. The instrumentation consisted of two load cells for shear and normal loading, eight displacement laser extensometers for shear, normal, and lateral displacements and fourteen acoustic emission sensors for monitoring evolution of asperities’ degradation during the test. The friction angle obtained is 72° for the peak and 58° for the residual. The high values of friction angle indicates that first-order roughness and good interlocking of the joint surfaces can result in high shear strength parameter values in a rock generally regarded to have low values.

Jan 1, 2015

By W. J. Dick, K. G. Kress

A pipeline syphon can be a simple and reliable alternative for water conveyance as compared to otherwise more complex pumping systems or low-level outlet conduits through earthfill dams. In a simple form, it consists of a pipeline constructed over the top of a dam or other high topographic feature, connecting a source pond to a receiving pond or channel (Fig. 1). The syphon action is initiated by removing air from the pipeline (priming) using water pumps, vacuum trucks, or simple devices that can be purchased “off-the-shelf.” Once primed, the syphon flow rate can be controlled or stopped using conventional gate, valve, orifice plate, or other devices. Repriming is not required even if the flow is stopped, provided the syphon was not drained. A limiting factor in considering a pipeline syphon as a design option is the maximum lift (i.e. vertical distance from source pond water level to summit of pipeline syphon) which is approximately 9 m or less, depending on pipeline syphon features and site conditions. A pipeline syphon can be quickly constructed from readily available materials including steel, concrete, polyethylene, or PVC pipe. It is particularly well suited to many of the unique conditions often encountered at mine sites. This paper identifies situations that can sometimes be best resolved using a pipeline syphon. It provides basic principles for pipeline syphon design and includes case histories of their successful application.

Jan 1, 2005

By G. T. Lapidus, R. M. Luna-Sánchez

In the present study, a series of cyanidation experiments were performed on a bulk sulfide concentrate which contained silver in four distinct phases, to determine its extraction rate, varying the oxygen concentration. The results showed that three of the four phases were refractory, aguilarite (Ag,iSeS) being the only leachable phase, and that the effect of the oxidant concentration is minimal. Mathematical simulations were performed, adjusting only the Damkohler number to adequately fit the experimental data. This model, and the mechanism implied, was compared with that found for acanthite (Ag2S) in a previous study, and the differences between the two discussed.

Jan 1, 2005

By Robert E. McIvor

The Functional Performance Equation for Ball Milling” was first presented in 1988. It now has been used successfully in more than a dozen mineral processing plants. This powerful, yet simple tool provides a new level of understanding of closed circuit grinding. It shows how grinding circuit efficiency is in reality comprised of two distinct efficiencies. It demonstrates how circuit production rate is related, collectively, to these two efficiencies, mill energy input, and the grindability of the ore. It links circuit performance to design and operating variables that can be manipulated, and creates an effective strategy for making plant improvements. This paper covers the derivation and industrial validation of this equation. As part of an engineering and management system that also incorporates suitable metrics and process control, other operators can now use this tool to make improvements and to manage the performance of their grinding operations with clarity and confidence.

Jan 1, 2005

By E O. Foster

When roasting started at Giant Yellowknife Mines in 1949, it became apparent that, to prevent air and water pollution in the surrounding district, it would be necessary to collect the arsenic that was contained in the exit gases of the roaster. The arsenic collection problem was finally solved by the installation of both electrostatic and baghouse collectors. It was realized that a considerable quantity of gold-bearing dust was leaving the roaster with the exit gases. When the collection problem was solved, it was possible to measure this loss. The loss proved to be considerable and it became evident that a substantial quantity of gold could be recovered. Research programs on dust treatment began in 1958, and by May, 1960, the treatment process which is currently being followed was started in the plant. At present, the two electrostatic preci11itators, Operated at temperatures above 600°F, collect the gold-bearing dust.

Jan 1, 1963

By Robert B. Parsons

"New Brunswick Finance Minister John Baxter pulled something out of a hat for the mining industry in April, but there is a general concensus in the industry that he should put II back where it came from.The industry has never been in the mood f or progressive rate structures, but that is exactly what New Brunswick 's 1984 budget offers to this depressed sector of the economy.IntroductionThe Province of New Brunswick stunned the Canadian mining community in April with the announcement that the province' s 16% mining tax rate would be replaced with a progressive rate structure effective January 1, 1984 (Table I). The proposed change, contained in the bud get papers tabled by Finance Minister John Baxter on April 17, caught the industry totally by surprise. The move to a progressive rate structure was completely unexpected for a variety of reasons:• Generally speaking, relations between the province and the industry have been relatively good, yet the industry was apparently not consulted with respect to the proposed measure and had no indication that a change of th is nature was coming. This is in stark contrast to the mood which prevailed during the major revamping of the province' s mining tax regime in 1977: at that time, the industry was invited to contribute in advance to the province's plan for a new tax structure.• The new structure would appear to make th e province less competitive in terms of mining tax rates with Ontario , Quebec, and other provinces, despite indications in the past that New Brunswick is very cognizant of this competitive factor in formulating mineral policy.• A joint report in November 1978 by federal and provincial officials to federal and provincial finance and resource ministers, which was careful not to directly criticize Ontario and Quebec's progressive mining tax rate structures, recommended that provincial "" tax regimes be examined to ensure the inclusion of appropriate mechanisms to avoid the excessive taxation of cyclical type profit "" , and that ""the federal and provincial governments consider the concern over progressive tax regimes expressed by the industry and examine mining and royalty tax regimes and the income tax regime with a view to alleviating the effect of such regime on the aggregate marginal tax rate"". In this context, any move to a progressive rate structure would be viewed by many observers as retrograde."

Jan 1, 1984

By S. G. Luckey, N. R. Harrison, F. Nadeau, U. Brüx

"The adoption of tailored-rolled or tailor-welded blanks (i.e. TRB/TWB) in the automotive industry has been known to offer great potential for the optimization of weight, function, cost and complexity. Vehicle light weighting can further be achieved by using high strength aluminum alloys like the 7xxx-series. 7xxx-series alloys are capable of delivering specific strengths equal to or greater than high strength steels. However, room temperature formability of this aluminum class is limited, so one approach to forming 7xxx-series alloys is by hot stamping. Hot stamping utilizes an elevated temperature blank and the high pressure stamping contact of the forming die to simultaneously quench and form the sheet. This paper explores the initial feasibility of tailored thickness material for body-in-white applications when processed under hot stamping conditions.INTRODUCTION Steel tailor-rolled blanks (TRB) or tailor-welded blanks (TWB) have been used within the automotive industry as a method of reducing weight, expanding material utilization, and decreasing overall part/assembly cost (Ganeasan et al., 2015; Merklein et al., 2014; Hirt et al., 2005; Kridli et al., 2000). The production of such tailored thickness materials has resulted in over $2.5 billion (2016) in combined industry sales (Mubea, 2018). As automakers begin to adopt the manufacturing practices traditionally reserved for steel such as tailor rolling/welding with greater enthusiasm for vehicle light weighting, there exist an opportunity to expand the material database to extend beyond the traditional aluminum alloys found in current production. High strength aluminum alloys, i.e. 7xxx-series, are ideal for structural automotive applications due to their high specific strength; however, they have limited room temperature formability. Hot stamping, another manufacturing practice used by the steel industry, can be used to form these high strength materials. The combination of tailoring the thickness of a sheet material and hot stamping provides an opportunity for significant weight saving within an existing manufacturing footprint. This paper explores the potential and challenges of this approach when applied to structural body-in-white components. The methods for tailor rolling, tailor welding and hot stamping are described and applied to the production of a 7075 aluminum alloy B-pillar. The results are discussed in terms of feasibility and weight savings."

Jan 1, 2018

The principles and utility of in-situ coal gasification are discussed, and a first field test conducted by the Alberta Research Council in 1976 near Forestburg, Alberta, is described. The test was carried out in a 12-ft subbituminous coal seam under 60 feet of cover. Within this seam, a 30 by 60-foot block , containing approximately 650 tons of coal, was delineated by four injection/production holes which were oriented to take advantage of the natural fracture system in the coal. Linkage between holes was established by reverse combustion and gasification was accomplished by injecting air into the ignited coal. No steam was injected but operating pressures were adjusted to utilize formation waters for partial carbon -steam gasification. The coal gasification runs lasted six weeks and gasified an estimated 900 tons of coal ,' during sustained periods of gasification, a fuel gas with heating values of between 110 and 150 Btu/scf was obtained. Plans are now being developed for excavating the test site and inspecting the subsurface cavities created by gasification.

Jan 1, 1977

By Justin S. Johnsen

As OEM sensors and interfaces have grown in number, the available data from equipment in the mining environment has continued to multiply. This equates to an increased visibility of operating performance, mechanical and electrical health, and predictive monitoring that can directly improve maintenance reliability and scheduling. With increased visibility, where should a reliability engineer begin to look to directly impact Capacity Assurance? More specifically, what source will provide inputs to the Failure Modes Effects Analysis (FMEA)? Results from these analyses must be documented, and they must contribute to the overall mission of the mining company; these results must reduce costs and increase profits. Through detailed data capturing, documenting, and analysis, Modular Mining Systems? Time Tracking application, used in the MineCare® maintenance management solution, can drive decisions and provide direct impact to engineering projects for continuous improvement in the mine maintenance organization.

Nov 1, 2011

By John Wilson

"The Rietveld numerical method was used to calculate the relative abundances of phases in both synthetic binary mixtures and synthetic and natural ores, using X-ray diffraction data. The results were compared with those of image analysis and a chemical method. The ranges of the relative errors were estimated. The Rietveld method is found to be acceptable for determining the abundances of major and minor phases and the amorphous component of partially crystalline samples. In complex mixtures, where there are several trace phases (~<2 wt%) present, the technique becomes less accurate. It is most useful as an alternative technique to image analysis when sample preparation is problematic or sample particle sizes are sub-micron. It is a manual method which requires user input during the fitting process, but is both simpler and faster than image analysis due to the reduced set up time and sample preparation required. It is now implemented at CANMET as a technique for quantitative analysis.INTRODUCTIONUntil recently, the Applied Mineralogy group at CANMET used only image analysis and chemical techniques to determine phase quantities. An effort to develop quantitative X-ray diffraction (XRD) has been on-going for several years. Initially, the reference intensity ratio (RIR) method with external standards was tried with some success (Szymanski and Petruk, 1989). The main difficulty with this technique was finding adequate standard material for each phase present in the sample. This shortcoming made the method ultimately impractical, given the wide variety of materials which come to the laboratory for analysis.The Rietveld refinement method of quantitative XRD (Hill et al 1993, Mumme et al 1996), in contrast, requires no standards and requires minimal sample preparation and therefore a more rapid turnaround compared to image analysis. The Rietveld method also has advantages over image analysis in that it can identify and quantify polymorphs, ultra fine materials and many types of hydroxide products. As well, it is useful for analyzing materials such as bauxite or talc, which do not polish well enough for making mounts of the quality required for image analysis. To quantify amorphous material and phases which are present in amounts below the detection limit of XRD, the addition of a standard material is still required. However, in such cases only one standard is needed, which is alumina."

Jan 1, 2003

By J. P. Harrison, N. Bozorgzadeh, M. Dolowy-Busch

"It is common in rock engineering practice to characterize the triaxial strength of intact rock by using only data samples of small size. Practical guidelines such as ASTM support such sample sizes. In this paper, we investigate the reliability of the Hoek-Brown strength criterion estimated from such samples. For this purpose, we use an unusually large published set of triaxial strength data to randomly select a large number of data samples of small size to simulate the situation that frequently encounters in practice. The samples are generated with different arrangements with regards to the confining pressure. We fit the Hoek-Brown criterion to each of these samples, obtain estimates of strength parameters and compare them to those obtained from the complete data set. Our analysis suggests that estimates based on small samples are not reliable and can lead to both over- and under-estimation of strength.Additionally, we use these small samples to investigate the statistical methods for obtaining design values of strength as suggested by limit state design standards such as Eurocode 7. We show that, if used in conjunction with small samples, these methods do not guarantee a safe estimate of strength and in many cases lead to highly over-conservative estimates.We present a potential solution to this problem by augmenting the small data sets with Bayesian informative priors to give much more reliable estimates of strength. We conclude with suggestions for the development of informative prior distributions."

Jan 1, 2015

By S. Qian

Galvanic corrosion is a potentially major concern associated with the application of stainless steel reinforcement which is in direct (electrical) contact with carbon steel reinforcement in concrete structures. Judicious use of stainless steel rebar in both new construction and rehabilitation of older structures is a viable, cost-effective option for extending service life and reducing maintenance costs. Questions, however, had arisen about the possibility of increased corrosion due to galvanic effects. This paper investigates the galvanic-coupling behaviours of three different types of stainless steel and carbon steel. Tests were performed both in electrochemical cells and with specimens in concrete inside an environmental chamber. The results show that oxygen reduction on stainless steel is the rate-determining factor for galvanic coupling of these two metals. It is much lower than that of passive carbon steel. As a result, the galvanic coupling of stainless steel with carbon steel will not increase the risk of corrosion of carbon steel reinforcement.

Jan 1, 2005