Search Documents

By K. Kawagishi, K. Matsumoto, Y Koizumi, H. Harada

A new burner rig for cyclic and hot corrosion testing of Ni-base superalloys and high-temperature coatings has been developed at the National Institute for Materials Science (NIMS) in Japan. The concepts of the rig design include: use of kerosene as fuel, easy operation for materials research and multi-specimen testing capability per test run. The burner rig consists of six blocks including combustion block, corrosion-solution injection block, furnace block, specimen block, controller block and outdoor facility block. During verification testing, it was confirmed that the rig had accurate specimen temperature control within ±1? from 600 to 1100? and automated easy operation. Cyclic testing of several Ni-base superalloys was conducted. The results from 50 cycle testing indicated that a new NIMS alloy developed for 1700? class gas turbine had higher oxidation resistance than CMSX-4. This new burner rig testing capability at NIMS can be very useful for future oxidation, hot corrosion and coating durability studies.

Jan 1, 2010

By Bruno Bussière

Le drainage minier acide (DMA) provenant de la circulation des eaux à travers les rejets miniers sulfureux est sans doute le principal problème environnemental auquel est confrontée l?industrie minière. Afin de prévenir les problèmes environnementaux reliés au DMA, on doit restreindre la présence de l?une et/ou de l?autre des principales composantes menant à la production d?acide, soit l?eau, l?air et les sulfures. Pour ce faire, différentes techniques ont été proposées au cours des dernières années, dont la désulfuration environnementale et les couvertures avec effets de barrière capillaire (CEBC). Dans ce papier, on propose d?utiliser ces deux techniques en combinaison. Ainsi, on produirait un rejet désulfuré à l?usine de traitement qui pourrait, par la suite, être utilisé comme matériau pour la couche de rétention d?eau de la CEBC. Dans un premier temps, on présente les résultats d?une étude de laboratoire qui montre qu?il est possible de désulfurer les rejets de concentrateur à l?aide de la flottation non sélective jusqu?à l?obtention d?un résidu non générateur d?acide. Par la suite, des essais en colonne ont permis de démontrer qu?il est possible de limiter la production de DMA d?un résidu sulfureux à l?aide d?une CEBC dont la couche fine est constituée de résidus désulfurés. Des prédictions théoriques estiment même que la présence de sulfures résiduels dans la fraction désulfurée utilisée comme matériau pour la rétention d?eau peut avoir un effet bénéfique en réduisant la migration d?oxygène. En effet, les sulfures contenus dans la couche de rétention d?eau peuvent consommer l?oxygène qui tente de migrer vers le bas et, ainsi, réduire les flux d?oxygène qui atteignent les rejets réactifs.

Nov 1, 2002

By Daniel Lachapelle, Nuri Hmidi, Turgut Yalcin

"Simulation can serve as a convenient tool in studying the behaviour and performance of grinding circuits by facilitating the evaluation of various scenarios and identification of optimum operating conditions. This technique was applied to the St Andrew Goldfields Ltd.’s Stock Mine Mill which is a 1300 tpd gold milling facility, offering custom milling services as well as processing the Company’s own ores. Lack of adequate instrumentation in the mill poses a challenge in attaining optimum performance especially with changing ore types and characteristics. The grinding process is monitored essentially by manual measurement and adjustment of pulp densities at various streams. A simulation program was designed to assist in the effective implementation of this mode of grinding control. Product sizes from both the primary and secondary grinding circuits were correlated empirically to relevant process variables using a database formed from the results of past sampling campaigns. The simulator was created in Microsoft Excel whose data analysis and optimization tools coupled with its Visual Basic Programming capabilities were found to provide an excellent environment for the development of a cost-effective, efficient and user-friendly simulation program.INTRODUCTIONGrinding is often a very costly unit process in milling operations, mainly due to the excessive energy consumption associated with it. For example, for a Canadian copper-zinc flotation mill, grinding was listed as being the most costly item taking up 30.4% of the total milling expenses, followed by the flotation cost at 2 1 .O% (Kidd Creek Mines Ltd., 1982). A survey on 45 copper flotation mills around the world showed the average grinding cost to be 34.5% of the total milling cost (Weiss, 1985).Overgrinding aggravates the cost issue, while insufficient grinding either causes loss of valuable minerals to tails or results in low-grade concentrates. Therefore, it is essential that grinding circuits be carefully controlled and monitored. To this end, a great deal of effort has been devoted over the years to the modelling and simulation of grinding systems in order to assist in the efficient running of these processes."

Jan 1, 2001

By S. Konetschnik, Lux Degel, R. Degel, T. Haslinger

UrbanGold and its partners from Mettop and SMS group have developed a novel technology for the recovery of valuables from all non-ferrous metals’ fractions of WEEE (Waste Electrical and Electronic Equipment), with a special focus on low qualities which are commonly landfilled or incinerated. The technology is marketed under the brand name “UrbanGold Flex” to illustrate the high flexibility in respect of plant design and raw material portfolio, allowing also the processing of low grade material and materials with high caloric values. The process of the technology’s centrepiece, a modified and enhanced bath smelting furnace called “HENRI”, was investigated in numerous pyrometallurgical trials as basis for a scale-up towards a capacity of up to 100,000 tons of WEEE-concentrates per year. All relevant facility components have been evaluated in respect of references, fall-back options, as well as exit strategies (alternatives) to minimize risks when establishing a novel technology. A spin-off within the development is the “UrbanGold Compact” technology which can be seen as optimization of state-of-the-art smelters by using an optimized TBRC as primary processing unit. As an UrbanGold Compact plant will be the first industrial scale reference of UrbanGold’s technologies, it is also explained in the publication. As precious metals recovery is of major (economical) importance when recycling WEEE, major attention has been given to minimize the losses of these valuables. These measures, as well as a sophisticated way of utilizing waste heat as far as possible, result in interesting business cases with gross profits of up to 20% or even more. INTRODUCTION Over the past years, the demand of electrical and electronic equipment has increased dramatically with technological progress. Innovations on the technology of electronic devices led to a shorter usage and lifespan and thus boosted the generation of Waste Electrical and Electronic Equipment (WEEE). WEEE is one of the fastest growing waste streams, growing at 3 to 4% per year worldwide and is expected to reach more than 52 million tons per year by 2021. Currently, about 45 Mt of these wastes are estimated to arise worldwide, and the trend is rising (Baldé et al., 2017).

Jan 1, 2019

By Joe Zhou

"Mineralogical characterization and metallurgical extraction of silver is challenging due to its complex mineralogy and chemistry. Over 200 Ag-bearing minerals have been identified and a silver-rich ore body would typically contain 5 to 10 different silver minerals. Silver can occur not only as discrete microscopic (visible) silver minerals but also as submicroscopic (invisible) silver in other minerals. During processing, silver may form passivation compounds such as silver hydroxide, silver sulphide, jarosite-like silver sulphate, silver halide or silver cyanide precipitate, all of which may negatively impact on silver extraction. Knowing the deportment of silver in the ore and its metallurgical products is important in flowsheet design and plant optimization. This paper begins with the classification of silver ores and minerals and a review of processing techniques, and focuses on the major mineralogical factors to explain why and how these factors affect silver extraction. Case studies are provided to demonstrate the application of silver process mineralogy in flowsheet design and plant optimization.INTRODUCTIONSilver was known to and utilized by mankind since ancient time. Actually, it was one of the earliest metals discovered and utilized by mankind after gold and copper.Silver is the whitest metallic element. It is rare, strong, corrosion resistant, and unaffected by moisture, vegetable acids, or alkalis. Silver is also resonant, moldable, malleable, and possesses the highest thermal and electric conductivity of any substance. The chemical symbol for silver is Ag, from the Latin argentum, which means white and shining. Although silver does not react with many chemicals, it does react with sulfur, which is always present in air at trace amounts. The reaction causes silver to tarnish, and consequently it must be polished periodically to retain its luster.Silver possesses many special physical characteristics and qualities that make it useful to a variety of industries. The photography industry is the biggest user of silver compounds. Silver forms the most light-sensitive halide salts, which are essential to developing highquality photographic prints. Silver also has the highest electrical conductivity per unit volume of any metal, including copper, so it is used extensively in electronics."

Jan 1, 2010

By d&apos, F. Elia

Hot cracking of magnesium (Mg) alloys during welding creates a barrier to enhancing the use of these alloys in automotive applications. As a result, it is imperative to understand the mechanisms responsible for hot cracking of Mg alloy welds in order to develop means of eliminating this problem. In this study, the hot cracking susceptibility of AZ91E and AE42 magnesium alloys were assessed using the moving torch Varestraint test method. Plates of 3 mm thickness were extracted from AZ91E and AE42 ingots and subsequently tested. Quantitative cracking data in terms of maximum crack length (MCL) was used for evaluating the cracking susceptibility. Scanning electron microscopy was carried out. The results suggest that AE42 showed a higher resistance to hot cracking in comparison to the AZ91E alloy. This was attributed to the difference in microstructure between the two alloys. In the fusion zone and HAZ of AE42, the brittle needle-like A1IIRE3 phase was seen to decompose to the more ductile particle-like Al2RE phase, thereby increasing the alloy's resistance to hot cracking. In contrast, SEM fractography revealed that brittle A16Mn and Mg17A112 intermetallic particles segregated to grain boundaries and triggered hot cracking in AZ91E.

Jan 1, 2011

Pillars are used in various forms in underground mining. For several decades pillar design has been an issue in both soft and hard rock underground mining. The major use of pillars is in room-and-pillar type mining. Pillars are critical structures in the production levels of block cave mines. With most mines leaning towards the use of block caving for ore extraction today, pillar design has become even more important. Empirical pillar design is popular. The use of numerical modeling is becoming more common in the design of underground mine pillars. A critical review of both the empirical and numerical modeling approaches to the design of underground mine pillars reveal some fundamental flaws. In general, pillar design approaches often assume the pillars are vertical, and are subjected to pure compression. Pillar failure criteria are then based on this assumption. Most papers on numerical modeling for pillar stability assessment use vertical pillars. This paper shows that where pillars are not subjected to pure compression the empirical pillar design approaches are inadequate, and that when using numerical models for the assessment of pillar performance, more care is needed in the determination of the average pillar stresses. The practice of relating field scale pillar strength to laboratory scale intact rock strength determined from conventional laboratory compression tests in empirical design equations is misleading when pillars are inclined or subjected to compressive and shear stresses. New data is added to the hard rock empirical pillar stability chart, and it is shown that it is misleading to conclude that failure of pillars with width to height ratios greater than 2.3 should not be anticipated. New empirical pillar design charts are presented for pillars at various degrees of inclination for different ko-ratios.

Aug 1, 2013

By V. G. Papangelakis, G. P. Demopoulos

"Recovery of gold from refractory ores and concentrates presently constitutes one of the most important, challenging, and exciting areas of R&D activity in the gold processing industry. New technologies are being tested for the treatment of refractory gold materials, some of which have been advanced to the level of commercial operation. In this paper, some recent technological developments in the hydrometallurgical processing of pyritic matrix-refractory gold ores are highlighted. Key operational steps of each of the alternate hydrometallurgical technologies are analyzed and potential advantages and drawbacks are identified. The processes which are reviewed are: hydro chemical oxidation, biochemical oxidation and pressure oxidation. INTRODUCTIONOver the years the term ""refractory"" has been applied in gold ore processing to denote situations in which straightforward cyanidation failed to yield high gold recoveries. A number of mineralogical and chemical factors may be responsible for this ""refractoriness"" problem. A systematic classification of the different options for their treatment has been discussed in a recent review paper. In this paper, the pretreatment of the submicroscopic gold encapsulated within the matrix of pyrite and arsenopyrite minerals is considered. This type of gold is the ultimate refractory material because complete breakdown by reaction of the host mineral structure is required.The method which has been traditionally applied for the treatment of pyritic-type refractory gold ores is an oxidation roast (single stage or double stage depending on the As content) of a flotation concentrate to produce a porous calcine, the latter being more amenable to cyanidation. Despite its established practice, oxidation roasting is not considered particularly attractive with today's standards for high product recovery and clean environment. Roasting is known to be very sensitive to heating parameters and feed composition and deviation from optimum conditions can result in reduction in permeability which is translated to incomplete gold liberation."

Jan 1, 1989

By M. Abumiya, N. Onodera

Stabilization of arsenic via the precipitation of large-sized scorodite (FeAsO4·2H2O) particles usually involves the use of expensive autoclave systems operated under high temperature and pressure conditions. Alternatively, DOWA developed a novel scorodite synthesis process (DMSP®) wherein the Fe(II) ions in solution containing As(V) ions were oxidized by O2 gas under atmospheric pressure. In this process, crystalline scorodite particles were formed via the formation of a gel-like precursor containing Fe(II). Based on this concept, in this study, we have demonstrated the synthesis of scorodite particles by the addition of Fe(III)-containing solution to the experimental solution containing Fe(II) and As(V) ions, without the O2 gas oxidation process. Ferric sulfate (Fe2(SO4)3) was used as the source of Fe(III) ions. Results indicate the precipitation of scorodite particles, comparable to that of the O2 gas oxidation method.

Jan 1, 2014

By Stephen L. Chryssoulis

"""Preg-robbing"" of gold by carbonaceous matter during the cyanidation of certain types of carbonaceous gold ores is well documented. Recent studies established that ""preg-robbing"" of gold is not limited to carbonaceous matter. Gold sorbed on the surface of pyrite grains was detected and quantified by TOF-LIMS (Time of Flight Laser Ionization Mass Spectrometry). Crystallites of pyrite from a number of ores from different geological environments have been shown to have gold on their surface apparently sorbed from the ore forming solutions. Surface gold accounts for significant fractions of the gold head assay. Preg-robbing of gold by pyrite from pregnant cyanide solutions was also documented, and accounts for significant losses to tailings. Preventative measures are discussed.1.0 IntroductionThe detection and subsequent quantification of gold sorbed on the surface of pyrite particulates came about during routine determinations of the deportment of gold employing the comprehensive mineralogical approach (Chryssoulis and Cabri, 1990). In some pyritic gold ores it was discovered that the sum of the various forms in which gold ""conventionally"" occurs, was short of the gold assay. The mineralogical procedure used involves the independent determination of each fraction of gold, in other words there is no form of gold which is calculated ""by difference"". The systematic shortfall after having added the forms of gold listed in Table 1 led to the inquiry for the 'missing' gold and its discovery on the surface of pyrite grains, such as crystal facets and fractured surfaces.Preg-robbing of gold by pyrite from pregnant solutions was first described by Lloyd. In his studies, preg-robbing was measured by changes in the solutions/solids gold assays. This paper describes the first application of a direct measurement method for surface gold on pyrite particles from untreated and processed samples, its impact on gold deportment and processing. The advantage of the direct measurement lies in the absence of interference from other forms of gold, leading to more accurate and precise determinations of this unconventional form of gold."

Jan 1, 1997

By E. L. Bruce

EUROPEAN Russia is mainly a great plain, the average elevation of which is only 600 feet above sea level and the maximum elevation less than 1,200 feet (Figure 1). The main divide between the Arctic ocean and the Black sea and Caspian sea is an indistinguishable topographic feature from which the Dneiper and Don rivers flow southward to the Black sea and the Volga river to the Caspian. The valleys of these rivers are but little below the general level (Figure 2). To the south, this great, rolling plain is broken by a low ridge of Precambrian gneisses and intrusive rocks. The Crimea is an upland from which the descent to the Black Sea coast is precipitous (Figure 3). The Ukrainian Soviet Socialist Republic occupies the southern part of the plain. It is the southwestern unit of the Union, bordered by Rumania and Poland on the west and by the Crimean Soviet Socialist Republic on the south.

Jan 1, 1938

By Corrie Pitzer

Safety performance in many companies and even industries has stalled in the few years. Accidents rates are at a ?plateau? and yet, serious accidents and fatality rates are not. In more dramatic cases, such as in the BP Texas disaster, organizations that have ?exemplary? safety statistics, suddenly have a catastrophic or multi-fatality event occurring. Other classic examples are the Piper Alpha disaster and NASA?s Challenger and Columbia disasters and even the Chernobyl nuclear reactor. Looking into the root causes of these accidents provides an insight into the events and deficiencies that led up to the accident, but what are the common features in the organization?s mindset? What characterizes these organizations? decision making, their approach to safety and to risk and are there specific cultural features that can be delineated? The research and review presented in this paper covers a period since 1994, which started in the Australian resource industry and since then covered international events. The features of these organizations are summarized as the seven deadly delusions, based on extensive research since 1997 of organizations that suffered unexpected disasters. Their huge focus on safety, the achievement of lofty goals and celebration of safety successes led to ?mindset? that they are leaders in safety, protected by an extraordinary safety system and that their safety incident figures indicated a truly world-class safety performance. It led them into the trap of the seven deadly delusions?

May 1, 2011

By J. A. L. Henderson

THE potential oil-and gas-bearing area with "which this paper deals is the large undefined Carboniferous basin, roughly triangular in shape, occupying about 10,000 square miles of southern and eastern New Brunswick. Its base, about 135 miles long, lies on the gulf of St. Lawrence and embraces the whole eastern coast-line of the Province, while its apex lies in the south-west corner of the Province, near the International boundary (see map, Figure 1). The Carboniferous basin may be divided roughly into two areas-the Northern basin and the Southern basin-by a structural feature represented by a ridge of low hills running north-easterly from the Saint John river, near Saint John, on the southwest, to Indian mountain, about eight miles north of Moncton, in the northeast. Within the Northern basin, all evidence regarding the presence or attitude of the older Mississippian Albert Shale series, the only oil-bearing rocks known in New Brunswick, is for the greater part obscured by a thick and practically horizontal blanket of Pennsylvanian strata and, although evidences of oil and gas have been reported, none has been positively identified. Five parallellines of gentle folding, running to the northeast, occur in the Pennsylvanian rocks, within a distance of 100 miles from north to south. This folding is reflected in the courses of the rivers, which lie within the synclines. The relationship of the folding in the younger rocks to structures in the uncomfortably underlying older rocks is unknown, but should now be possible of clarification by means of a geophysical survey accompanied by drilling. Independent geological examinations have yielded no evidence of value in this respect, nor have five exploratory boreholes drilled by per-cussion tools to a maximum depth of 3,645 feet been of assistance, as only one inconclusive hole completely traversed the beds which normally overlie the Albert shales.

Jan 1, 1940

By C. G. Anderson

As the global demand for copper and gold steadily increases and the need for environmentally sound processing also grows, successful hydrometallurgical treatment of enargite (Cu3AsS4) concentrates has come to the forefront. This type of concentrate contains considerable arsenic so that successful arsenic fixation, for example as scorodite, is of the essence. This paper outlines the successful application of low temperature and low pressure nitrogen species catalyzed (NSC) hydrometallurgical pressure oxidation of enargite concentrates. The successful stabilization of the arsenic as an iron arsenate compound is discussed. Also, the use of experimental design software is highlighted as a process application and optimization tool.

Jan 1, 2006

By T. Vovan, A. Galibois, M. Fiset

"In order to establish some links between the 22 specimens found on the site of Les Forges du St. Maurice, their slag inclusions have been analyzed by electron microprobe. Comparison between their contents of various specific oxides allowed us to segregate them into two major groups and even to isolate two sub-groups possibly characterized by some equilibrium between their oxides and/or the type of ores used.In all probability, limes/one coupled systematically with a soil rich in hydrated aluminum silicates was used as a flux.Based upon the existence of a pseudo equilibrium between the slag and the metal, the elaboration of the bulk of the specimens can be ascribed to the indirect rather than the direct method whereas the process temperature can be estimated at at least /400°C.RESUMEDans le but d'etablir des liens entre les 22 objects provenant des Forges du St-Maurice, leurs inclusions de scories ont été analysées par microsonde. La comparison des teneurs en divers oxydes a permis de les séparer en deux groupes majeurs et même d'y distinguer deux sous-groupes pouvant être reliés à la forme d'équilibre entre certains oxydes et/ou au type de minerai utilisé. Selon toute vraisemblance, le fondant utilisé était de la pierre à chaux à laquelle on ajoutait systématiquement une terre riche en silicates hydratés d 'aluminium.Des considérations sur l'existence d'un certain équilibre entre les scories ei le métallaisset croire que la plupart des objets ont été élaborés plutôt par la méthode indirecte que directe et que la température d'élaboration se situait à au maint 1400°C."

Jan 1, 1984

By R. C. Gilmore, J. F. Brune

"Pulverized limestone rock dust used in United States underground coal mines to prevent and suppress coal dust explosions must easily disperse by forces of a methane or coal dust explosion. Moisture in the mine environment causes caking of the dust. Colorado School of Mines researchers performed dispersibility tests in a full-size explosion test drift. Tests included conventional, hydrophobized, and rock dust approved for German mines. Conventional and German standard rock dust products partially agglomerate, which may not be effective in suppressing a coal dust explosion, while hydrophobic rock dust retains better dispersibility.INTRODUCTIONA coal dust explosion devastated the Upper Big Branch mine in 2010 resulting in the death of 29 miners, the worst mining accident in the United States since 1972. The explosion propagated through approximately 65 km of active mine workings, but was extinguished in areas that had been properly rock dusted (Page, 2011). Researchers have long studied and established the ability of inert limestone rock dust to suppress coal dust explosions, see Richmond et al. (1975), Cybulski (1975), and Sapko et al. (2000).To be effective, rock dust must contribute to a total inert content of > 80% by weight and 100% of rock dust particles must pass through an 850 µm sieve, while 70% of the rock dust must be finer than 74 µm. This is established in US regulations 30 CFR §75.2. Dry rock dust is a nuisance that prevents mining work downwind from rock dusting activities. To overcome this problem, dust manufacturers have proposed applying the rock dust as a wet slurry or foam. After drying, manufacturers expected the slurry or foam-applied dust to have the same explosion suppression capabilities as dry-applied rock dust.Researchers at the Colorado School of Mines (CSM) designed and built a full-scale, underground Explosion Test Facility (ETF) at the CSM Edgar Experimental Mine in Idaho Springs, Colorado about 20 miles west of the CSM Golden, Colorado campus. To disperse the different rock dust products, researchers produced an air pressure pulse using a mesh array of PETN detonation cord. This method is simpler, more reproducible and safer than other methods considered, including methane-air explosions and a compressed air cannon. The detonation cord blasts produce a wind velocity of 30 to 50 m/s, the minimum velocity at which coal dust explosions can propagate, based on research by Nagy (1981) and Cybulski (1975)."

Jan 1, 2019

By Chris M. Healey

"Abstract- The Jasper Gold mine in northern Saskatchewan produced a total mill feed of 140 127 tonnes at an average grade of 19.0 g/t Au. Both diamond drilling and chip samples from under­ ground workings returned extremely high values, up to 12 851 g/t (375 oz/I) Au over 0.10 meter from a chip sample. In the presence of such extremely high grades, the accurate estimation of reserves is a major problem.ln the first part of this study, production data from the mine were used to evaluate the results of a variety of reserve estimation techniques in this environment. In two out of three cases studied, indicator kriging with assays cut to 342.9 g/t (10 oz/I) gave extremely good results. In the third case, however , indicator kriging gave unacceptable results. Instead, lognormal kriging of uncut data gave the best results.Secondly, from the same database, a number of drill-hole spacings were simulated, and reserves estimated from the simulations. As may be expected, the results of this analysis show increasingly better results with tighter drill-hole spacing. However, even with a 5 m by 5 m spacing the variation from actual grade was quite large. This is not a systematic under- or over-estimation of grade, rather a random scatter of results .The results of this study show very clearly the problems of deriving good estimates of reserves when extremely high-grade samples are encountered. There is a high degree of randomness to this database, so reserve estimation in this situation will remain a high-risk operation."

Jan 1, 1993

By S. Banisi, A. Haji-Zadeh, A. R. Hasankhoei, M. Maleki-Moghaddam

At the concentration plant of the Gol-E-Gohar Iron Ore Company (Iran) three 9m × 2.05m AG (Autogenous) mills (fixed speed) are used in parallel in a dry operation. The test works conducted in a scale down mill with a diameter of 1m indicated that conventionally used "deflector" type liners did not provide efficient environment for grinding. In this research, to improve the grinding efficiency, a new design using low profile end liners incorporating radial ribs of proper height was investigated. In order to determine an appropriate liner design at different operating conditions, a 100cm×10.8cm model mill was used for experimentation. The special design of model mill made it possible to increase the radial ribs height in steps of 6mm up to 18.5mm. The transparent end of the mill enabled accurate trajectory determination by image analysis. The results indicated that the new lower height profile deflectors and 15.5mm-height (14.5cm in industrial scale) radial ribs improved the mill performance while avoiding excessive pressure drop across the mill and wear on the liner. The image analysis showed that the use of new liners increased the distribution of coarse particles across the mill cross section from 28% to 35%. A new liner design was proposed by decreasing the number of liners in each slice from 5 to 4 pieces. The thickness of the inner head liners reduced from 45cm to 30cm and the outer deflector liners replaced by radial ribs. The distance between the feed and discharge inner head liners increased from the original 115cm to 145cm which increased the effective length of the mill by 26%. The new design reduced the weight and volume of end liners by 9% and 23%, respectively. It was predicted that the new liners design increases the mill throughput by 10% and reduces the metal consumption by 20%.

Jan 1, 2016

By D. W. Ginsberg, D. Cieplinski

"The lifetime cost of a material handling system, or any mine system, can be reduced through the application of quality engineering. Dynamic simulation is a powerful tool that can be used to enhance the experience and ingenuity of the design team. It cannot only de-bottleneck the system to improve system productivity, but also define critical design criteria to eliminate over-design and reduce capital cost. Eliminating over-design also reduces operating costs by lowering component replacement costs and by ensuring all parts of the system operate at a higher utilization and efficiency. IntroductionA mine owner’s profitability is improved when a mine is developed at the lowest lifetime cost. This cost relates not only to capital and operating costs, but also, to a great extent, on the efficiency and reliability of the operation. These factors are tied directly to the quality of the engineering which depends on the experience of the engineers involved, and their ability to apply known system information in a rational and constructive manner.It is becoming apparent that it is increasingly more difficult to deliver the quality of engineering expected and needed to provide attractive lifetime costs using traditional design methods. Historically, system information has been evaluated based on a limited amount of information to which global rules-of-thumb and the engineer’s personal experience were applied to develop design criteria. However, market forces are dictating that more system parameters be defined and that they be defined more accurately so that the most economical system can be developed. This increase in the volume of information and the need for more accurate predictions is straining, if not already exceeding, the ability of engineers to apply simple global rules of- thumb and to combine all the information in a rational, comprehensive and representative set of design criteria. Furthermore, as proposed system production rates increase beyond established industry practice, the extrapolation of the engineer’s experience becomes more difficult and increases the risk in the proposed design."

Jan 1, 1998

By R. H. Watson

A paper read by J. A. H. Church before the Northern Alberta Branch last February described a method of working thick inclined coal-seams from the dip upwards, with the view to preventing fire risk by using water for the stowage of waste workings, and extinguishing a conflagration should such break out, was favorably received; but there was some doubt as to the cost of such a method, as it involves a retreating system, which might prove too expensive for practical adoption. Let us consider a typical leasehold such as we are familiar with in the Rocky Mountains. The leasehold is crossed at one end by a mountain river, which is cut by the outcrop of a seam of coal, 30 feet in thickness, pitching as shown on the drawing herewith, which also shows the general line of the outcrop in elevation through the leasehold, which is two and a half miles long and contains 1,500 acres. The average lift is about 600 feet above river level and drilling has proved that the coalseam can be tapped at a depth of 1,500 feet, 2,000 feet down the pitch from the outcrop in the river, all as shown in the illustration, which is typical enough of our mountain conditions to serve the purposes of comparison of methods. We take up the leasehold and invest $30,000 to pay for drilling and prospecting; $30,000 more for the price of the lease to locator or holder, and say $100,000 to pay for a railway spur (it might cost twice this sum, but we are only comparing two methods in the same location) and "now we are ready to consider equipment and the cost of development.

Jan 1, 1924