Search Documents

By Dave Bulled

"This paper describes the design of an SABC grinding circuit using CEET technology applied to grindability data produced from testing 100 samples and distributed across the blocks of a mine plan using a geostatistical approach. The data distribution required the identification of the location of the sample points and a geological plan of the 130 million ton Ruby Creek orebody together with a mine plan of about 11000 blocks to be mined during the proposed 18 year life of the mine. The mill design was then made with consideration for the estimated hardness of each block in terms of both SAG and Ball milling with allowance for annual periods when the ore is harder to grind. Operating specifications were selected to achieve an optimum of capital and operating costs through use of the CEET program. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the hardness estimate of each block of ore in the mine plan. The final design could then include a quantification of risk and determination of safety factors based on the accuracy of block hardness estimates and CEET model fitting.INTRODUCTIONThe traditional approach to plant design involves the extensive testing of a single large composite sample or a small number of composite samples that are reputed to represent the ore body. It is accepted that the tests used can accurately measure in the laboratory the grindability of the sample by a process representing that to be used in the plant. The size of equipment required to achieve a specified throughput and product size is then calculated from one of a variety of models that have been developed by metallurgists over years of trial and error. Since these tests and models are tried and tested, they are accepted as reasonably precise; however during the operation of the resulting plant the design is sometimes found to be inadequate. It is then suspected that the flaw in the design process lies in the samples not being sufficiently representative of the ore body, since using only a single or small number of composite samples does not recognize the variability of the hardness of the ore, nor does it allow for the lack of precision in the hardness value used in the design.This paper outlines a design procedure suited to an orebody that is described by a geostatistical analysis of a reasonably large number of small samples of drill core. The analysis required the identification of the location of the sample points and a geological plan of the orebody, together with a mine plan of the blocks to be mined during the proposed life of the mine. The mill design was then made using the estimated hardness of each individual block with an allowance for annual fluctuations in the grindability of the ore. The geostatistical analysis assigned a statistical error to the hardness estimates of blocks and of each production year such that the final design included risk estimates and safety factors based on the possible errors that arise from having a limited amount of sample data (Kosick et al. 2002)."

Jan 1, 2007

By Xiao min Zhou, Yan Xu, Hongzhen Liang, Xiaonan He

"With the increase of shaft excavation depth, the thickness of the shaft lining increases sharply. It is difficult to reduce thickness of lining effectively by improving high-strength concrete performance. The concept of the New Austrian Tunneling Method (NATM) is that surrounding rock plays a certain role in tunnel support. The solution should be to find the correct relationship between shaft lining thickness and rock strength, which is related with the interaction between the surrounding rock and concrete lining. The plane strain mechanics model is introduced to calculate lining thickness. Shaft lining design of Cixi Colliery in China is completed with the mechanics-based method proposed in this study. The lining design is verified through numerical simulation and field monitoring. The simulation results show that the maximum mises stress is located at the inner edge of the shaft lining. The increase of lining thickness cannot effectively reduce concrete grade. The monitoring results indicate that a lining design thickness of 900mm with C60 concrete, is safe and reliable in the shaft over 1000metres.This analytical design method can well be referenced in similar deep shaft projects.INTRODUCTION The New Austrian Tunneling Method (NATM), thought to have helped revolutionize the modern tunneling method, is the most extensive design philosophy and construction principle in today's tunnel engineering. It began to attract attention in the 1960s based on the work of Ladislaus von Rabcewicz, Leopold Müller, and Franz Pacher in Austria[1]. NATM was originally developed for tunneling in depth and in high situ-stress conditions in the Alps. The history of sequential excavation was reviewed, which highlights the progress of tunnel design and construction in Europe after NATM[2]. Structural conditions were introduced into the equilibrium of tunnels in NATM, and the additional force was estimated to stabilize the excavation of the tunnel[3].From the perspective of applied mechanics, there was no accuracy theory to explain the interaction between the tunnel structure and the surrounding ground. Numerical calculation is an effective means to study the basic mechanism of tunnel excavation[4].Based on two-dimensional modeling approaches in the past, such as NATM and other derivatives, a three-dimensional model was studied to"

Jan 1, 2019

By L. Shasko, M. Hurlbert

As climate change is increasingly perceived as a problem, and fossil fuel based power production options are increasingly limited through regulatory restrictions and public distaste, future options become constricted. Reflexivity and social learning elicited through qualitative and mixed research methods offer important insight into what future power production pathways might be. Given factors of cost, baseload requirements, and energy density, options such as nuclear may be increasingly accepted. This paper explores this literature and possible methods of pursuing the reluctant acceptance of nuclear energy.

Jan 1, 2020

By P. Wells, P. Quinn

"A moveable flotation miniplant was designed and constructed at the research laboratory of Inco Technical Services Ltd. to address the need for flowsheet development with a limited amount of ore (such as drill cores). It consists of one rod mill, two regrind ball mills, one vibratory screen, 24 flotation cells of various sizes and two Venturi aerated flotation columns. The setup has continuous monitoring capability for pH, dissolved oxygen, oxidation-reduction potential, conductivity and temperature in conditioning tanks and flotation cells. Various options regarding flotation reagents, circuit configurations, and fineness of primary grind and regrind can be readily evaluated. The throughput of the miniplant is 20 – 30 kg/hour ore.Unit operations such as flash flotation, magnetic separation and gravity concentration can also be evaluated as an integral part of an entire flowsheet development.This communication describes the basic design features of the miniplant and some examples of applications are given.INTRODUCTIONInco operates numerous mines in Sudbury and Thompson and will shortly bring the Voisey’s Bay mine into production. It has long been recognized that the ores from different mines or from different depths of the same mine can give different responses in flotation. There is a growing need to properly evaluate the ores before feeding the mill to maximize the return of the mine/mill operation. Inco Technical Services Limited at Sheridan Park, Mississauga, Ontario has developed a batch laboratory procedure to address this issue. The results are considered in the overall economical assessment of new mine operations.For ores that cannot be processed by the existing mill operations or that will be processed by a new mill, it is necessary to develop a flowsheet that can maximize the economical return of the mine/mill operation. While recognizing the importance and contribution of the laboratory batch flotation procedure, it does not generate reliable data for flowsheet simulation and design. A full-scale pilot plant campaign is normally required to obtain the design data but often this is not possible due to a limited amount of ore obtainable from the drill core. A small-scale pilot plant (mini pilot plant or miniplant) capable of processing 20-30 kg/h ore can provide this data prior to a full-scale pilot plant campaign. A miniplant can also be used to optimize the circuit configurations, reagent additions and recycle options of process water before pilot plant work and can be used to test a different flowsheet configuration for an existing mill before re-piping a plant circuit."

Jan 1, 2003

By J. Cayouette

In 1995, Louvicourt mine started one of the first paste backfill operations in Canada. From 500 000 t in 1995, the annual paste backfill tonnage produced reached 800 000 t in 1999. The maximum throughput of the surface plant (including binders) is 3500 tpd with a final density of 75% to 76% solids which gives a slump of 15 cm to 17 cm. Following the start-up of the paste backfill plant, the backfill strength performance levels were well below the pilot plant’s predictions. The introduction of ferrous slag, laboratory tests on various binder ratios with or without additives, and the desliming of the tailings enabled us to optimize the mix and operation costs. Primary and secondary stopes are filled respectively with a paste containing 4.5% and 2% binders in a mixture of 20% cement to 80% ferrous slag. In certain stopes, the binder ratio may vary from 2% to 7%, but always in a ratio of 80/20. Six years after start-up, or 4.5 Mt of paste backfill later, this paper discusses the present operation and the major changes that have occurred over the years to optimize both the operation and the paste fill quality.

Jan 1, 2003

By Frederic M. Langevin

?? Introduction ?? LaRonde ?? History of Seismicity and Rockbursting ?? November 27th 2002 Rockburst ?? April 1st 2006 Rockburst ?? December 11th 2006 & January 11th 2007 Rockbursts ?? Seismic Risk Management Plan ?? Conclusions ?? Located in Northwestern Quebec (Can.) ?? In operation since 1988 ?? Reserves at Shafts #1 and #2 depleted ?? Production now comes entirely from Penna Shaft ?? Deepest single-lift shaft in the western hemisphere (2240 metres) ?? 7300+ tonnes per day ?? 2007 Reserves (proven & probable): ?? By-products: Ag, Cu, Zn ?? Sinking #4 Shaft (LaRonde II winze)

Feb 1, 2008

By W. B. Agocs

"AbstractThe airborne magnetometer data of the Marmora iron ore deposit at Marmora, Ontario, have been used as an example to show the mapped results obtained by the use of line spacings of from 1 mile to 14 mile. The maps are illustrative of the results which could be obtained from such line spacings for any type of geophysical survey, and they show the probability of 'missing' a feature of economic value if the line spacing is too coarse.The probability equations are given for the crossing of randomly oriented features whose maximum dimension is less than the spacing of the control lines for circular, elongate, and rectangular outlines. The equations are P = D/S; P = 2L/S; P = 2(L+W)/,.S; P = A/,.S; P = (2L(S+T)-L2),.ST; and P (D(S+T-,.D)) ST, respectively; where P is the probability; D is the diameter; L is the length; W is the width; and S and T are line spacings.IntroductionTHE EFFECT of station spacing, and the effect of the distance between the plane of observation and the plane of the source of the potential field anomalies, have been studied by geophysicists in the past.The purpose of this paper, however, is to illustrate the effect of line spacing •on the resultant mapped magnetic anomaly for a known magnetite mass, and to present the elementary probability equations for determining the optimum control spacing for detecting a particular type of feature. The effect of line spacing which is illustrated by the magnetic maps presented herewith would be comparable to results which would be obtained by any geophysical survey, since the contours between lines are of necessity interpolated."

Jan 1, 1955

By K. L. Murphy, G. Multamaki, P. M. Huck

"A preliminary evaluation, based on existing data, has been made of the implications of placing radium-barium sludge in tailings areas. The study was restricted to a consideration of possible increases in the quantities of radionuclides escaping to the environment through either groundwater or surf ace water, considering the types of tailings treated and the effluent treatment systems currently operating in Canada.IntroductionIn the recovery of uranium from ore deposits, the tailings produced by mine/mill complexes are conveyed to impoundment areas in slurry form. After settling, the supernatant is discharged to the environment together with runoff from precipitation on the tailings bas in. Currently, all operating uranium mines in Canada employ barium chloride treatment to control the release of dissolved radium to the aquatic environment. The dissolved radium in the tailings decant is precipitated with barium chloride, forming (Ra,Ba)SO4, and allowed to settle in ponds or lakes. In some instances, settling tanks have replaced ponds and flocculants have been added to aid settling. Because the Atomic Energy Control Board does not consider the precipitation ponds to be suitable for final disposal of these sludges, acceptable sites must be found. Options which have been suggested for sludge management include underground placement either in worked-out mine areas or in special chambers, or placement in the tailings areas. Conceptually, the latter alternative is attractive and probably would minimize sludge handling. This alternative would be subject to the AECB policy which requires that upon abandonment, radioactive releases from a tailings area must be within present regulatory limits and that treatment to meet these limits should not be required in perpetuity.No quantitative data exist concerning either the effect of physical and chemical conditions in the tailings on resolubilization of radium from precipitated sludges or the fraction of this additional radium which would be released."

Jan 1, 1982

By Gavin Ritson, Chris Ward

"The oil sands industry is still fairly young with the first viable oil sand operation having been started in Alberta in 1960. Since then numerous modifications and improvements have been tried and implemented. The current process makes use of high velocity pumping of oil sands slurry with hot water (hydrotransport) to achieve separation of bitumen from the sand.A number of the oil sands processes have been adapted from unit operations that are used in mineral processing, such as crushing, screening, flotation, cycloning and thickening. This paper outlines a typical oil sands process flowsheet and investigates the differences and similarities in technologies and costs to other mineral processing industries. It also considers the very large throughputs required, and presents some of the difficulties and challenges currently faced by the industry as a result of high demand for oil and environmental pressures.INTRODUCTIONOil sands (also known as tar sands) deposits are found throughout the world. The Athabasca Oil Sands deposit in Aberta is the largest of these. Oil sands consist of a mixture of crude bitumen (a semi-solid form of crude oil), silica sand, clay minerals, and water. The Athabasca, Peace River and Cold Lake deposits cover 141,000 square kilometers and contain about 1.7 trillion barrels (270×109 m3) of bitumen in-place, comparable in magnitude to the world's total proven reserves of conventional oil"

Jan 1, 2009

By Zou Lisheng

The culture of safety is very important to coal mining production. About 90% of mine accidents are caused by human error. This paper analyzes the status of China?s coal mining accidents, and accident cause. This paper explains the concept of safety culture, the value of safety culture, as well as the relationships between safety culture and safety behavior, and between safety culture and science and technology. The paper proposes the model of safety culture and the ways to enhance safety culture of coal enterprises. Safety culture and safety production is closely related and are significant to the improvement of mine safety situation in China.

Aug 1, 2013

By A. McMullen

"IntroductionTHE LOW-VOLATILE bituminous coals of the Brazeau field, Nordegg, Alberta, are soft and weak in structure. The seams contain .bands of inferior material, locally designated 'black jack', and thin bands of friable carbonaceous shale having no definite horizon but usually 'floating' in the seam. Because of the weakness• of the coal and the friable nature of the shale bands, run-of-mine coal usually contains a very high percentage of fines, as •Shown in the following table:SIZE WEIGHT. %Plus 1/2 in 25.61/2 – 1/4 in 13.31/4 - 1/8 in 14.6Minus 1/8 in 46.5The most convenient way of cleaning the fine coal would be by treating it in association with the coarse coal, so that no additional plant would be necessary. To a limited extent this is possible in certain types of equipment, notably the jig. A system of washing without pre-sizing is not •attractive, however, when dealing with the friable coal under consideration, which contains •a preponderant proportion of fines. At the new Brazeau washery, separation is made at 3/8-inch on •a Robins 'Vibrex' •screen, the coarse sizes being cleaned in •a standard pulsator-type jig. A feldspar jig is used to clean the minus 3/8-inch fraction."

Jan 1, 1954

By T. M. Waterland

A GREAT deal of work has been done at Britannia during the past three years in improving and standardizing rounds for development headings, and the results obtained have been very gratifying. The round which has recently been adopted as a standard for all drifts and cross-cuts has, in some instances, doubled the average length of break formerly obtained. It has also increased the footage of advance per labour shift and reduced explosives' consumption. At the present time, with a shortage of skilled labour, more control is necessar7 in directing the drilling of rounds. The use of a standard round has been o great assistance to the foremen and shiftbosses. NATURE OF GROUND Most of the ground encountered consists of a moderately silicified chlorite schist, known locally as G.M.S (green-mottled schist). It cannot be termed hard ground, because a three and one-half inch Leyner will drill at an average rate of twelve inches per minute. Due to the abrasive nature of the ground, the gauge of the steel wears rapidly and in most cases one set of steel is needed for each hole. The ground is not 'free breaking and holes must be spaced correctly to obtain a maximum break. DEVELOPMENT OF STANDARD ROUND FOR THREE-SHIFT OPERATION Late in 1940, a development programme was started involving 7,000 feet of drifting, 6 ft. By 7 1/2 ft. In cross-section, in two headings. Plans were drawn up to advance the headings on three shifts. Equipment used in the headings was as follows: D.A.35 Leyner?machines, Eimco Model 12B mucking machines, nine one-ton end-dump cars, one Mancha Little Trammer on the longest heading, 20-pound rail, 4-in. 15 compressed-air line, 15-in. Fan pipe connected to 5 h. P. Coppus fan. Diamond-drill cross-cuts, 16 feet in length, were cut every 250 feet. Switches were installed at these cross-cuts and they served as passing points for the cars. One siding seventy feet in length was cut in each heading at approximately the half-way point. The cycle of operations planned was to muck out, drill, and blast each shift. Previous performance in this type of ground indicated that a daily advance of 12 feet to 14 feet might be made. However, if a better type of round could be developed, an increased daily advance would be possible. A study of the time available for each operation in a net working shift of six and one-half hours indicated that the maximum depth of round that could be mucked, drilled, and blasted each shift would be six and one-half feet. When this maximum depth was decided upon, the next problem was to develop a satisfactory round. Due to ventilation difficulties and to the short net working shift, the whole round had to be blasted at one time. In other words, no blasting of the cut-holes could be done.

Jan 1, 1942

By Rodrigo Toro, Mario Delisle, Claudio Zamora

"The mining market is researching innovative methods to train the workforce for mining which is normally extremely difficult to get. Thus, the dynamic simulation-based technologies become an essential pillar to educate and train the inexperienced staff at the pace required by this industry. Even if Operator Training Simulator (OTS) systems are commonly used in most of industries, knowledge transmitted to operators are unfortunately not ""capitalized"" in general. The OTS systems are usually delivered as a single hardware and software platform and very little as a full service long-term.In this article, an integrated solution to increase the efficiency of the operators is proposed. This solution is based on the combination of dynamic simulation, processes knowledge, virtual reality and the knowledge capitalization through the creation of simulation scenarios and e-learning. The Codelco Ministro Hales plant simulation project for a copper concentrator plant is presented as a real life example.IntroductionDynamic and real-time process simulation have proven to be a must in the development of greenfield projects, providing mechanisms to design and test controls design, interlocks, start-up, shut down sequences and operator training, among others (see (McMillan, 2006) for further details). Early adopters of this technology were utility power plants; in the petrochemical industry have become a standard, and in the mining industry the use of dynamic simulations is growing, especially in new projects and training of operations personnel for the adoption of best practices and new technologies, see (Nikkhah & Anderson, 2001) and (Toro, Ortiz, & Yutronic, 2012).This paper outlines a solution that utilizes dynamic simulations as the base of an integrated platform for operational effectiveness, which takes into account the current scenario of new mining projects and operations, where high turn over rates and needs of specialized workforce have given a special value to this kind of technologies."

Jan 1, 2015

By L. Narhi, K. Haavanlammi

"Approximately two thirds of annual nickel production is used as a raw material in the making of stainless steel, and about 60% of these nickel products are in the form of metallic nickel such as nickel cathode or briquettes. In the stainless-steel production process nickel is blended with iron and chrome-based raw materials, and metallic nickel is typically only required for final steel fine-tuning. Outotec offers a new FeCrNi technology to enhance the nickel value chain for stainless steel producers. This involves the use of an HPAL-based intermediate nickel product (e.g., mixed hydroxides or NiO) as raw material in the Outotec FeCrNi process, for the production of a FeCrNi Master Alloy. The new process, designated as the FeCrNi process, offers multiple benefits compared to existing technologies such as: higher tolerance for impurities in the HPAL intermediate product, avoiding the need for further nickel refining, and the improved recovery of all metals in the FeCr process. The complete new FeCrNi value chain is based on proven technologies such as HPAL and the Outotec FeCr-process. This new innovative and promising value chain offers improved efficiencies for the HPAL based nickel production process combined with excellent sustainability aspects.INTRODUCTION In today’s global economy there is a constant need to improve the efficiency and sustainability of the metals production. The requirements for modern metal refining are tightening and cost efficient, safe and sustainable operation is the precondition for all investment. Outotec is offering now a novel way to combine FeCr and Nickel production to create a completely new value chain to source nickel to stainless steel. BACKGROUND Nickel The current nickel mine production is in the level of 2,000 tons annually and it is split 44% from sulphide based deposits and 56% from laterite deposits (Figure 1). Most (40%) of the nickel is refined to pure nickel metal whereas other products are FeNi (19%) and Nickel Pig Iron NPI (20%) (Roskill). The remaining part, roughly 21%, is nickel chemicals and intermediates. Most of the new investments in nickel are in the direct shipping of laterite to produce nickel pig iron. HPAL process is considered in few projects but no major HPAL projects have been started since the Ambatovy plant in Madagascar. Ambatovy reached the commercial production in 2014. The main primary nickel used is stainless steel manufacturing. In the year 2016 about 68% (~1,360 kt) of primary nickel production was used in stainless steel."

Jan 1, 2017

By Rees J. Llewellyn

High chromium white irons can be formulated to provide required combinations of abrasion and erosion wear resistance, toughness and capability to withstand corrosion attack. As a consequence, they are used widely in casting form throughout the mining/mineral processing industry, particularly as components for slurry pumps and also as mill and crusher liners, laminated wear plates in chutes and hoppers and in valves, nozzles and cyclones. Traditional cast chromium molybdenum and high chromium white irons for wear applications are covered in ASTM A532 Classes 11 and 111 and are also available as comparable proprietary alloys. They rely on heat-treated, hypoeutectic microstructures containing a high volume fraction of very hard eutectic/secondary metal carbides and martensite to provide extremely high wear resistance. The ability to increase the carbide volume fraction and hence achieve higher wear resistance, has been limited because of severe casting difficulties encountered when carbon and chromium contents are raised and hypereutectic alloys with structures also containing coarse acicular primary metal carbides are produced. The limitation has been overcome and cast hypereutectic chromium white iron pump components have established themselves in a wide variety of mineral processing service applications. Comparisons will be made between the microstructures and wear test performance data for the various alloy types and details will be provided of the service performance improvements that have been achieved through the use of hypereutectic chromium white irons.

May 1, 2004

By B. Tanda

A process has been developed at Curtin University whereby glycine is used in an alkaline environment to leach gold, silver and copper from their ores, concentrates, process intermediates and wastes. Copper mineralisation investigated includes various oxides, sulfides and native copper. The leach process utilises an oxidising environment such as oxygen. Glycine is a non-toxic, non-volatile, edible, low cost reagent which is produced in large industrial quantities for use in several industries. Glycine and its copper and precious metals complexes are stable over wide pH, Eh and temperature ranges. Other than losses in leach residues, the glycine is recovered and recycled for leaching. Iron dissolution is insignificant in the pregnant leach solution. Iron in pyrite remains unaffected, whereas iron associated with base metal sulfides (e.g. chalcopyrite and bornite) is converted to a readily filterable iron hydroxide. Efficient separation of copper by solvent extraction and conventional electrowinning has been shown to be feasible for a number of organic extractants, whereas gold and silver glycinates adsorb very well onto carbon allowing CIP/CIL/CIC (carbon-in-column) based processes. The process is ideal for ores containing acid-consuming gangue, concentrates with high arsenic or halide contents and for copper-gold ores with significant sulfide mineralisation. The process eliminates many of the problems associated with the processing of copper-gold-silver ores, such as elemental sulfur formation, silica gels, unwanted metal co-dissolution, and jarosite precipitation. The reagents used and process residues are much safer and environmentally benign than conventional process options. The processing technology can be applied to in-situ, heap and vat, or agitated tank leaching at temperatures ranging from ambient to below 100?C at atmospheric pressure and is currently being commercialised. This paper will focus on copper leaching and recovery and iron rejection from a chalcopyrite flotation concentrate.

Jan 1, 2016

By W. Blum

Progress made in improving the creep resistance of Mg alloys is reviewed with the emphasis on microstructural interpretation. Experimental results on the increase of creep strain with time at constant stress a measured for limited times and strains are displayed in a transparent form as creep rate-strain diagrams from which the minimum creep rate stress is safely derived. In addition, data on the thermal stress component a derived from high-precision a-reduction tests are reported. Within a simple statistical dislocation model these data allow one to quantify the relation between dislocation velocity v and a . In combination with structure evolution laws this relation serves as a basis for modeling the creep rate. New alloys have distinctly higher creep resistance than AZ91 where precipitation hardening plays a minor role. This is due to hardening by intermetallic phases which may form a continuous skeleton along the grain boundaries (e.g. Ca-alloyed AZ91) and/or submicron-sized precipitates within the grains (MRI230D, Mg-Zn-Ca alloys).

Jan 1, 2006

By C. Edwards

ABSTRACT The versatility and specificity of rare earth elements (REEs) have led to their use in an everincreasing variety of applications in new technologies; consequently, demand for REEs has increased significantly. However, separating REEs safely and effectively is a complex and expensive process. This paper presents a review of REE mineral processing technologies, providing an update on current capabilities in REE mineral processing and REE extraction from the major commercially valuable REEbearing minerals such as bastnaesite, monazite, and xenotime, as well as the ion-absorption type of REE deposits.

Jan 1, 2013

By N. Erarslan, M. Ghamgosar

With the increased use of mechanized rock excavation, there have been developed internationally a number of methods to assess the abrasivity of rock materials. These methods range from determination of abrasive and hard mineral content using petrographic thin section analysis to weight loss or rate of wear flat development on specified test pieces. The Cerchar abrasivity index (CAI) test has been widely accepted for the assessment of rock abrasiveness and is determined as the abrasion of a steel pin after scratching over the freshly-broken or saw-cut surface of a rock. Two types of testing devices are in use today: (i) the original ‘Cerchar apparatus’, and (ii) the ‘West apparatus’, which was adopted herein. The CAI is calculated from the measured diameter of the resulting wear flat on the steel pin after 10mm scratching. This test has been considered to provide a reliable indication of rock abrasiveness for isotropic rocks. However, a great amount of rocks in natureis anisotropic. Phyllite is an anisotropic and foliated metamorphic rock and various types of phyllite specimens were tested in this research. Although phyllite is a type of rock primarily composed of quartz and the expected CAI value can be high, mechanical cutting of this rock should not be very problematic compared with igneous rocks have same CAI value. As phyllite is a foliated metamorphic rock, most of the specimens split into sheets through the quartz seam by the tip during scratching normal to the axis of quartz seams. Hence, viability assessment of Cerchar abrasivity test and F-Schimazek index values for the anisotropic rocks is investigated in this research.

Jan 1, 2015

By S. Hunt, D. de Vries

Kansanshi Copper Smelter began operation in March 2015. The smelter features a single Isasmelt furnace for smelting, one 6-in-line electric furnace for matte-settling and slag-cleaning duties, four Peirce- Smith converters and two rotary anode furnaces. A 1,450 t/day oxygen plant and a 4,085 t/day sulphuric acid plant are included in the smelter operations. This paper gives an overview of the operational performance to date with summary data for each smelter section. Challenges such as an unforeseen refractory failure in the Isasmelt furnace in 2016 are discussed. Design improvements around the electric furnace are mentioned. Plans for potential future improvements are put into context. A consistent focus on operations, maintenance and continuous improvement has seen the smelter easily achieve its nameplate capacity of 1.2 million tonnes per annum of copper concentrate throughput. The smelter now operates consistently at a concentrate throughput rate of 1.38 million tonnes per annum of copper concentrate. INTRODUCTION The smelter was commissioned in March 2015. Design and commissioning of the smelter have been discussed by de Vries, Hunt, Hanschar and Louie (2016). The smelter rapidly ramped up to achieve nameplate production (1.2 million tonnes per year concentrate) and in 2018 operated consistently at the rate of 1.38 million tonnes per year concentrate. This paper presents major operational data for each section of the plant and describes significant events and improvements during the first four years of operation. The smelter flowsheet is shown in Figure 1.

Jan 1, 2019