Search Documents

By T. M. Waterland

A GREAT deal of work has been done at Britannia during the past three years in improving and standardizing rounds for development headings, and the results obtained have been very gratifying. The round which has recently been adopted as a standard for all drifts and cross-cuts has, in some instances, doubled the average length of break formerly obtained. It has also increased the footage of advance per labour shift and reduced explosives' consumption. At the present time, with a shortage of skilled labour, more control is necessar7 in directing the drilling of rounds. The use of a standard round has been o great assistance to the foremen and shiftbosses. NATURE OF GROUND Most of the ground encountered consists of a moderately silicified chlorite schist, known locally as G.M.S (green-mottled schist). It cannot be termed hard ground, because a three and one-half inch Leyner will drill at an average rate of twelve inches per minute. Due to the abrasive nature of the ground, the gauge of the steel wears rapidly and in most cases one set of steel is needed for each hole. The ground is not 'free breaking and holes must be spaced correctly to obtain a maximum break. DEVELOPMENT OF STANDARD ROUND FOR THREE-SHIFT OPERATION Late in 1940, a development programme was started involving 7,000 feet of drifting, 6 ft. By 7 1/2 ft. In cross-section, in two headings. Plans were drawn up to advance the headings on three shifts. Equipment used in the headings was as follows: D.A.35 Leyner?machines, Eimco Model 12B mucking machines, nine one-ton end-dump cars, one Mancha Little Trammer on the longest heading, 20-pound rail, 4-in. 15 compressed-air line, 15-in. Fan pipe connected to 5 h. P. Coppus fan. Diamond-drill cross-cuts, 16 feet in length, were cut every 250 feet. Switches were installed at these cross-cuts and they served as passing points for the cars. One siding seventy feet in length was cut in each heading at approximately the half-way point. The cycle of operations planned was to muck out, drill, and blast each shift. Previous performance in this type of ground indicated that a daily advance of 12 feet to 14 feet might be made. However, if a better type of round could be developed, an increased daily advance would be possible. A study of the time available for each operation in a net working shift of six and one-half hours indicated that the maximum depth of round that could be mucked, drilled, and blasted each shift would be six and one-half feet. When this maximum depth was decided upon, the next problem was to develop a satisfactory round. Due to ventilation difficulties and to the short net working shift, the whole round had to be blasted at one time. In other words, no blasting of the cut-holes could be done.

Jan 1, 1942

By F. R. Erick Mulder

"AbstractTwo bottom-hole samples have been taken from two new completions in the Turner Valley field, Royalite Lowery No. 8 on the west flank and Royalite No. 73, which was deepened into a lower fault block, on the northeast flank. From the bottom-hole oil of Royalite Lowary No. 8 a synthetic sample was prepared to simulate the original fluid in the reservoir, saturated at the gas-oil contact conditions. The sample from Royalite Lewery No. 8 has been shown to be the original fluid present at this well and represents the oil phase near the oil-water contact in• the reservoir. Complete chemical analysis, P.V.T., and viscosity data have been obtained on these reservoir fluids, which represent the range of saturation from the gas-oil to the oil-water contact in the Turner Valley oil structures. Sampling techniques and the application of the analytical data to reservoir conditions and field operations are discussed. Super-compressibility curves for an average separator tail gas have also been prepared. These data have not been available before. They will be of fundamental value in futu.re reservoir engineering studies of this field and will also serve as a guide in determining operating practices."

Jan 1, 1950

By Q. Li, X. -L. Lei

Accompanying global energy shortage and high energy prices, shale gas has been the focus of exploration and it has attracted great attention from both academia and industry. The combination of horizontal drilling and hydraulic fracturing enables the extraction of huge quantities of shale gas from impermeable shale formations. During the process of hydraulic fracturing, great amounts of water, sand and chemicals must be injected into the shale formation at a high pressure, which may trigger seismicity. Such events could occur due to the presence of faults or the reactivation of these potential faults. Shale is the main component of source rock in the Sichuan Basin, China, and has the greatest contribution to the natural gas of the basin. In order to investigate the fracturing mechanism of shale in the Sichuan Basin, China, a series of rock fracture tests under triaxial compression were carried out in the laboratory in order to investigate the hydraulic fracturing behavior in relation to the seismicity. Based on the high multichannel waveform recording system, the detailed spatio-temporal distribution of acoustic emission due to micro-cracking was used to examine the deformation and fracture behavior of shale. In addition, the effects of confining pressure on the deformation and fracture in shale under triaxial compression by acoustic emission monitoring and X-ray computed tomography were discussed in the paper. The experimental results indicate that the shale samples demonstrate brittle fracture behavior. The confining pressure has a great effect on the complexity of the fracture planes and the spatial distribution of acoustic emissions, but few contributions to the location of the major hydraulic fracturing plane. The foliation of shale plays a dominant role in the rupture process and the geometry of the major hydraulic fracturing plane. The high confining pressure increases the strength and restrains the deformation of shale during compression process. These results shed some light on the understanding of onset of hydraulic fracture initiation not only for shale gas exploration and production, but also for CO2 geological storage and underground energy storage.

Jan 1, 2015

By A. H. Mumin, A. Prikhodko

"This paper provides an understanding of interpreting and evaluating airborne time domain electromagnetic (TEM) surveys as applied to massive sulfide exploration. Variations in the conductive morphologies of massive sulfide ore systems are discussed, followed by forward modelling exercises examining the derived TEM response to these morphologies and discussion of the subtleties of data interpretation. Deposit morphology in the orientation at formation and the variations occurring due to later deformation are considered. Images of corresponding resistivity–depth models are provided. The combined modelling results provide a low-cost method for initial interpretation and screening of TEM anomalies. RÉSUMÉ Cet article nous permet de mieux comprendre l’interprétation et l’évaluation des levés élec-tromagnétiques aéroportés en domaine temporel (TDEM, de l’anglais time-domain electromagnetic) appliqués à l’exploration du sulfure massif. Y sont débattues les variations au niveau des morphologies conductrices des systèmes de minéralisation du sulfure massif, suivies d’exercices de modélisation prospective qui examinent la réponse dérivée des TDEM à ces morphologies et d’une discussion sur les subtilités de l’interprétation des données. L’étude envisage la morphologie de l’orientation originelle non déformée des gisements ainsi que les variations résultant d’une déformation ultérieure. Des images des modèles correspondants de résistivité-profondeur sont fournies. Les résultats combinés relatifs à la modélisation proposent une méthode peu onéreuse d’interprétation et de contrôle initiaux des anomalies dans les TDEM.INTRODUCTION Electromagnetic geophysical surveys are an indispensable foundation of many mineral exploration programs and can account for as much as half of the predrilling exploration costs. Quantitative mass interpretation of the survey results remains difficult due to the infinite variation of deposit morphologies, their complex physical properties, and the presence of barren conductive materials that can mimic or mask the response of targeted ore. Many modern geophysical investigations that focus on time domain electromagnetic (TEM) data interpretations are devoted to problems with inversion and modelling and their algorithms. Although a few of these investigations have resulted in commercial software products, these require highly qualified and experienced users and usually include geometric assumptions. Furthermore, without the input of known physical properties and geometric constraints, the inversion results are highly ambiguous. A number of case studies document the geophysical responses to known targets in well-defined and diverse geo-electrical environments, providing a high degree of correlation between field obser-vation and the results of the modelling used in this style of investigation (Hone, 1980; Schneider & Emerson, 1980; Tyne, Idnurm, & Malone, 1981; Bishop & Lewis, 1992; Hopgood & Hungerford, 1994; Meju, 2002; Yang & Oldenburg, 2016). The uniqueness of the target/environment parameters and their specific features limits the use logy is poorly understood. The responses are therefore that are devoid of complicating environmental factors (e.g., highly conductive overburden and hostrocks or nonuniform target conductivity) as a first approach to the interpretation process of such case studies as the main reference for interpreting TEM survey responses in areas where the underlying geomodelled from generalized and typical geological models"

Jan 1, 2018

By S. Hunt, D. de Vries

Kansanshi Copper Smelter began operation in March 2015. The smelter features a single Isasmelt furnace for smelting, one 6-in-line electric furnace for matte-settling and slag-cleaning duties, four Peirce- Smith converters and two rotary anode furnaces. A 1,450 t/day oxygen plant and a 4,085 t/day sulphuric acid plant are included in the smelter operations. This paper gives an overview of the operational performance to date with summary data for each smelter section. Challenges such as an unforeseen refractory failure in the Isasmelt furnace in 2016 are discussed. Design improvements around the electric furnace are mentioned. Plans for potential future improvements are put into context. A consistent focus on operations, maintenance and continuous improvement has seen the smelter easily achieve its nameplate capacity of 1.2 million tonnes per annum of copper concentrate throughput. The smelter now operates consistently at a concentrate throughput rate of 1.38 million tonnes per annum of copper concentrate. INTRODUCTION The smelter was commissioned in March 2015. Design and commissioning of the smelter have been discussed by de Vries, Hunt, Hanschar and Louie (2016). The smelter rapidly ramped up to achieve nameplate production (1.2 million tonnes per year concentrate) and in 2018 operated consistently at the rate of 1.38 million tonnes per year concentrate. This paper presents major operational data for each section of the plant and describes significant events and improvements during the first four years of operation. The smelter flowsheet is shown in Figure 1.

Jan 1, 2019

By J. A. Finch

Individual mineral cyclone performance curves were determined for the four major minerals at two lead-zinc concentrators. Sizing was by screen and cyclosizer down to approximately 10 um, with lead , zinc and iron as saying of each size fraction. The performance curves were similar in shape and located according to the mineral specific gravity, Pm. The curves displayed a discontinuity at the fine end and a magnitude of short-circuiting of fines to the underflow which increased with Pm. Mass fraction of water to the underflow was only a guide to this short-circuiting. Sharpness of separation seemed in dependent of Pm. An inflection in the over-all performance curve was shown to be a consequence of the individual component mineral performance. A general relationship was observed showing that the flow regime of classification changed from laminar/ intermediate to turbulent with increasing cyclone feed size. Individual mineral size reduction for the four major minerals at one of the concentrators was also determined. Size reduction of the silica was greater than that of the galena, in contradiction to their accepted relative grind-ability. The observation did correlate with silica being much coarser than the galena in the feed to the ball mill. It is suggested that the silica acted as a buffer to the galena.

Jan 1, 1977

By Jim Wickens, Andy Cole, John Pekrul

"The roaster facility at Barrick Goldstrike Mine treats double-refractory sulfidic/carbonaceous gold ore. Prior to oxidation in the roasters, the ore is ground in two parallel dry grinding circuits utilizing 19’ Ø x 75’ double rotator mills. The design plant throughput was 12,000 dstpd. However, process improvements have significantly increased throughput rates by 25-50%. The current daily throughput record is 20,078 dstpd. Grinding circuit improvements contributing to this success include feed size reduction, ball size optimization, automatic ball charging optimization, and operating strategy changes. In addition to the changes already made, this paper discusses future optimization initiatives including on-stream particle size analysis and “real-time” ore hardness determination techniques.INTRODUCTIONBarrick Goldstrike Mines is located 29 miles Northeast of Carlin, Nevada, USA. Through 2001, the property has produced over 23 million ounces of gold making it one of the premier gold operations in the world.Prior to Barrick’s ownership, the property began producing gold from a small heap leach operation in 1975. The small-scale heap leach production continued through 1986, and in January 1987, Barrick acquired the property. Increased exploration activity by Barrick significantly increased gold reserves. In August 1988, a 4,500 dstpd mill facility was commissioned to treat high grade oxide ore. Also, heap leach operations had significantly expanded. In 1990, the mill was expanded to 6,000 dstpd, and the first autoclave was commissioned to treat refractory sulfide ore. By the end of 1996, the mill and pressure oxidation facility had expanded to 16,000 dstpd and heap leaching had ceased as oxide reserves were exhausted. In 2000, a roaster facility was commissioned to treat double-refractory sulfidic/carbonaceous ore."

Jan 1, 2003

By J. -P. Lempainen, K. Haavanlammi, K. Valkama

The Outotec nickel matte chloride leaching process is especially suitable for small capacity standalone nickel refineries. The matte is leached with hydrochloric acid and oxygen in multiple steps in atmospheric OKTOP® reactors. Oxygen feed prevents reductive conditions and hydrogen formation in the leaching process. A sufficiently high acid concentration keeps the iron dissolved in the solution. The iron is removed after leaching by precipitation and the pregnant leach solution continues to metals recovery. The metals recovery from the chloride solution is done by solvent extractions, where ammonia is used for pH control. Copper and nickel are stripped from the organic phases into sulphate solutions. Metals can be recovered from the purified solution by conventional electrowinning. Other alternatives are precipitation or hydrogen reduction processes. The ammonium chloride in the solvent extraction raffinate is regenerated into ammonia. The calcium chloride solution from ammonia regeneration is routed to acid regeneration where sulphuric acid is added and ultra-pure gypsum is precipitated. The hydrochloric acid solution from this step is recycled back to leaching. The process yields good overall metal recoveries and expensive

Jan 1, 2014

By J. A. Haskin

The Engineering Department at Flin Flon has the following responsibilities: 1. Underground Surveying. 2. Open-Pit Surveying and Supervision of Blasting. 3. Mine Geology and Examination of Prospects. 4. Design of Plant Additions and Improvements. 5. Miscellaneous Field W ork, Reports, etc. The entire surface plant, as well as the underground workings, are located by co-ordinates based on a triangulation system covering an area approximately one mile long by one-half mile wide. The origin of this system and one end of the base-line is the southwest corner of Township 67, Range 29, west of the Principal Meridian. The bearing of the base-line was determined from the township boundary, which runs true north, so that all other bearings are almost astronomical. This is a great convenience when our surveys must be tied to mineral claims, rights-of-way, and land subdivisions. As the base-line extends across Flin Flon lake, its measurement across smooth ice was simple and accurate. The length, slightly over 1,600 feet, has been adjusted for the temperature and tension of the standard tapes used and checked sufficiently to ensure a maximum error of 1 : 15,000. Each angle was repeated ten times, but as no special refinements were used, errors of as much as four or five seconds are possible. The elevation of the origin of the triangulation system was approximately 1,050 feet above sea level. The use of this true elevation in our surveys would have resulted in negative elevations underground as soon as the mine reached a depth greater than 1,050 feet. To avoid this complication we therefore added 4,000 feet to this elevation. The collar of the Main shaft, for example, which is actually 1,072 feet above sea level, appears in our records as at elevation 5,072. Underground surveying, which follows standard practice, is done by two mine surveyors who share three helpers. The meridian is taken underground from two wires hung in either of the two vertical shafts.

Jan 1, 1935

By S. Caron, P. Radziszewski

Industrial practice in mineral processing shows that an important problem in understanding and monitoring in-mill parameters is due to the lack of fundamental knowledge and appropriate sensors. However, over the last decade, Discrete Element Method (DEM) modelling has shown an interesting potential in describing the fundamentals of grinding mill behaviour, in improving the understanding of internal grinding mill dynamics, and in developing solutions to industrial practice. With the objective of bringing this modelling technology into the concentrator control room to assist operators, this paper aims to describe the main elements needed to apply this emerging and developing technology to on-line mill performance monitoring.

Jan 1, 2004

By D. Imeson, T. Grammatikopoulos, M. Aghamirian, M. Oliazadeh

"More than 70% of potash is produced worldwide by froth flotation. Flotation of potash was developed in the early 1930s. Amines are widely used for flotation of sylvite (KCl) from halite (NaCl) and insoluble materials such as clays. Amine collector is also absorbed by clays. Therefore, clays are usually separated by scrubbing and de-sliming prior to flotation. Alternatively, slimes can be floated ahead of potash flotation. Flotation recoveries of sylvite are commonly in the range of 85%, while losses can occur in slimes, flotation tailings and make-up of process brine. Ores containing free coarse-grained sylvite are generally screened, whereas both fine and coarse fractions are conditioned and floated separately. The unique features of potash flotation include solubility of sylvite in water, the size of particles floated and fast kinetics. Particles up to 2.3 mm can be floated and about 50% of flotation feed can be removed in the rougher stage in few minutes. The main challenges in potash flotation are the recovery of potash from slimes, flotation efficiency in the presence of carnallite and recovery of coarse potash grains. A review of potash flotation shows that there is still room for improvement in both coarse and fine potash flotation. The present paper reviews the most significant flotation parameters including reagent type and dosage, flotation circuits, flotation equipment size and new developments in potash flotation. The latter include new reagents, flotation technologies (Hydrofloat, Jameson and column cells) larger flotation cells and slimes flotation.INTRODUCTION Potash is the common industrial term for potassium in various chemical combinations and minerals soluble in water. About 90% of potash produced worldwide is used as agricultural fertilizers. Flotation is the main treatment process of sylvinite (KCl-NaCl) ores for recovery of sylvite (KCl). Potash concentrate should contain a minimum of 95% KCl and be relatively free from 0.2 mm KCl fines. The flotation process for beneficiation of potash ores was developed in United States and Russia concurrently in the early 1930s. In 1934, Potash Corporation of America applied flotation process in a commercial scale (Tippin R.B. and Huiatt J.L). In the initial application, halite (NaCl) was selectively floated by employing lead chloride as an activator and soap as collector. The sylvite concentrate was reported in the cell underflow."

Jan 1, 2012

By Glenn Clarke, Ben Holloway, Barry Lumsden

"BHP-Billiton’s Cannington mine in Northwest Queensland produces a silver-rich lead concentrate and a zinc concentrate. The plant has the capacity to treat 3.1 mta and for the year to June 2006 mean feed grade was 10.3% Pb, 461 g/t Ag and 3.7% Zn. Recovery losses of lead and silver are primarily in the fine fractions. In 2001, the plant was modified when it was determined that splitting the lead feed into two size fractions, and floating the two fractions separately increased fine lead and silver recovery. The fine lead fraction (called the split float) is 80% <16µm and about a quarter of the lead and silver is in the finest fractions. In 2006 to further improve lead and silver recovery a statistical plant trial of magnetic aggregation conditioning of the split float feed was undertaken. While pure galena is diamagnetic the Cannington galena contains iron within the galena mineral resulting in the galena having a paramagnetic, magnetic susceptibility. The trial demonstrated to greater than 98% statistical significance an increase in lead recovery, and to 99% statistical significance an increase in silver recovery, and to greater than 97% significance an increase in the lead in concentrate in the split float circuit. These economic recovery benefits with magnetic aggregation of the split float feed, has led to the incorporation of this technology in the plant.INTRODUCTIONThe BHP-Billiton owned Cannington silver, lead and zinc mine is located in the Australian state of Queensland about 800 kilometres west of the coastal city of Townsville. This is a pastoral area characterised by large cattle farms, low population density and very little infrastructure. The area has two seasons, a wet, hot summer and a dry, mild winter. Because of its isolation and lack of infrastructure the mine has always operated on a fly in fly out basis.Geological drilling defined the resource as 43.8 million tonnes grading 11.6% lead, 4.4% zinc and 538 ppm silver (Walters and Bailey, 1998). At times during its history Cannington has held the crown as the single largest lead and silver mine in the world (Torrisi and Smith 2003). Another unique characteristic of the operation’s history is the rapid progress from discovery to operation. The first drill to intersect the ore body was in 1990 and the mine and plant was commissioned in 1997."

Jan 1, 2008

By Benjamin H. Clark

"For over 50 years, Derrick Corporation has been renowned for its innovative and durable fine screening equipment and screen surface technology. Derrick’s latest innovation, the patented Stack Sizer, offers mineral processors both high tonnage capacity and high separation efficiency on an extremely small footprint.The Stack Sizer is suitable for separations from 6.3 mm down to 75 microns (200 mesh). The Stack Sizer, coupled with Derrick’s patented urethane screen surface technology, offers an extremely economical alternative to hydraulic classifiers, hydrocyclones, and less efficient low volume wet screening systems. Stack Sizers have been used in feed preparation for flotation, spirals, and a variety of jigs. Mineral processors wishing to reduce grinding circuit circulating loads and generation of slimes due to over grinding, thereby enhancing the efficiency of flotation and gravity circuits, now have another technology at their disposal to perform this critical sizing and grade control function.Over 200 Stack Sizers have been installed in numerous mineral processing applications worldwide attesting to the rapid acceptance of this technology. Stack Sizers are currently screening ferrous and non-ferrous metal ores, mineral sands, silica sand, kaolin clay, feldspar, garnet, phosphate, aluminum dross, potash, coal, tantalum, spodumene, niobium, and other rare earth mineral ores.INTRODUCTIONDerrick engineers have long understood and demonstrated the importance of screen width in coupling both high capacity and high separation efficiency for fine wet sizing applications. As opposed to fine dry sizing, where the length of the screening machine is critical for high separation efficiency, introducing slurry feed to screens in a thin and even layer at minimal velocities across wider screen surfaces allows for high capacities and efficiencies, with maximum screen cloth life. This is due primarily to the combination of free liquid and high frequency vibration of the Derrick motors, which allow fine undersize material to pass through the screen apertures. Lacking either of these factors would be extremely detrimental to the screening process. Without the high frequency vibration of the motor, the screen is essentially a low efficiency sieve bend. Without the free liquid to carry fines through the screen openings, the screen is for all intents and purposes a glorified conveyor or dewatering unit, as little or no sizing takes place once the screen is devoid of free liquid. For optimal screening results, Derrick recommends feeding slurry to a screen at approximately 20% solids by volume. Figure 1 shows the Stack Sizer design concept. Note that a single feed point is used to evenly distribute the flow to the five separate feed points."

Jan 1, 2007

By G. F. Vander Voort

Over the past twenty years, steelmakers have introduced improved practices for reducing the inclusion content of steels. The success of these practice changes can be monitored in a variety of ways. Chemical analysis of the bulk sulphur and oxygen contents provides a relatively simple means to assess the impact of these changes. However, microscopical test methods are still needed to assess the nature of the inclusions present. Traditional chartbased measurement methods have wide acceptability, and their data are well understood by both purchaser and producer for heat acceptance purposes. However, these methods do have inherent weaknesses which limit their usefulness for quality control, SPC, and database applications. Image analysis-based chart measurements are an improvement over manually generated chart ratings, but the data still do not lend themselves to databases and statistical comparisons. ASTM Committee E-4 on Metallography has developed a stereologicallybased image analysis standard test method, E 1245, which provides the necessary data in a form which is easily databased and analyzed statistically. This paper describes E 1245 and shows how data from different heats and melting practices can be compared statistically to ascertain valid test differences.

Jan 1, 1998

By Ruy L. Rodrigues

Vale is in the early stages of commissioning its Onça Puma nickel operations. The project is meant for the production of 58,000 tpa of nickel contained in ferro-nickel, substantially contributing to the company?s vision to achieve world leadership in the nickel business. Mineral resources will be exploited from the homonymous deposits in the Midwest of state of Para, Brazil ? some 100 km southwestwards from the company?s Carajás iron ore properties. Resources as of 83 Mt at 1.73 % Ni will sustain a mine life of approximately 40 years. The property was acquired in late 2005 and Vale has since extended the engineering studies and proceeded with the implementation. Nickel will be mined from saprolitic ore at a rate of approximately 10 Mtpa (ore plus waste) in early years ? ramping up to some 15 Mtpa 7 years later ?, to feed the plant at a rate of 2.5 Mtpa. The process uses conventional RKEF (Rotary Kiln Electric Furnace) pyrometalurgical route whereby the ore is homogenized, calcined in rotary kilns, melted in electric furnaces and further refined to ferro-nickel. The plant has been designed and constructed applying the latest available technology, aligned with Vale?s vison to exceed the highest existing standards for environmental control, health and safety and productivity in the industry. Total investments in these operations are anticipated to correspond to USD 2.3 Bi and will materially contribute to the regional development and well being of the nearby communities and other stakeholders.

May 1, 2010

By S. C. Tadolini

"Roof bolts are the primary means of roof support in underground mines in the United States. Presently, post installation loads are measured on about 10% of the expansion anchor and combination bolts by using standard torque wrenches that Unit the accuracy of the measurements to about ±30%. No system has been available for measuring the loads generated on full-column resin grouted bolts. Mine roof bolts are long, slender, non-uniformly sized, roughly forged, and placed in a corrosive environment, creating obstacles for researchers trying to utilize ultrasonic reflection techniques to measure strain. A complete measurement system has now been developed by the U.S. Bureau of Mines, Denver Research Center. This system is being used successfully in determining loads measured on expansion anchor and combination bolting systems, examining the transfer mechanics of full-column, resin-grouted bolts, and measuring loads generated on bolts in an underground roadway support system.IntroductionMillions of roof bolts are used each year to provide structural support in underground U.S. metal, non-metal, and coal mines. Approximately 45% of the bolts used are expansion anchor, 45% are resin-assisted combination or full-column resin-grouted, and 10% are friction anchored. The effectiveness of these bolting types is dependent on a number of factors including rock density, bolt length, in situ stresses, rock properties, bolt pattern, installation tension, etc. When implementing expansion anchor and resin assisted combination bolts , installation and post-installation tension, or load, is a major determinant of support quality and subsequent behaviour of the reinforced roof. The method by which these systems carry roof loads is well understood and documented(1,2).The importance of these installation and long-term bolt tension measurements is well recognized and are required in the federal government regulations(3). A statistical sample of the bolts, lout of 4 during installation and lout of 10 inby the last open crosscut, is required to be measured using current torque wrench technology. The disadvantages of this system are the disturbance and weakening of the anchorage and limitations of accuracy to approximately ± 30%. The method by which resin-grouted bolting systems carry roof loads is much less understood, mainly because testing procedures used to evaluate point-anchor systems are not effective on resin-grouted bolts.Due to these problems, the U.S. Bureau of Mines designed a measurement technique that provided a highly accurate, low cost-per- bolt system that led to the development of ultrasonic pulse echo instrumentation. The original system was designed to measure the tension only on expansion anchor bolts. Recent developments and system modifications have permitted measurements on resin-assisted and full-column resin-grouted bolts. The use of these types of support systems has been increasing steadily in underground coal mines.The development of this instrumentation has provided laboratory and field results that help to explain the mechanics and relationships between the applied loads and the interaction between the grouted bolt system consisting of the bolt tendon, grout, and rock."

Jan 1, 1990

By M. S. Badollet

Introduction The manufacture of some asbestos products involves the use of asbestos in combination with water, cement and granular fillers. This type of production is often called the wet or semi-wet process and requires the use of either pressure or vacuum to eliminate the excess water in the fibrous blend so that the product may develop the proper strength during the curing stage. Asbestos - cement products available today are numerous and are a valuable contribution to the building industry. Their production in quantity depends upon the type of equipment employed, the speed at which it can be operated, and the factors involving the? blending of asbestos, cement, water, and fillers. Assuming that all mechanical troubles at a plant have been eliminated or are under control it is still advisable to study the basic properties of the raw materials used in the asbestos-cement products. The type of cement used is an important factor, but usually the manufacturer of the cement is willing to work with the asbestos development engineer and recommend the proper type to be used for the product. The source of the water should not be overlooked as a general factor involved in the production cycle. Waters containing a high percentage of contamination such as silts, humus, or soluble salts may adversely affect the setting of the cement or cause a slowing down of the production rate in the factory. Asbestos in combination with cement is an ideal material fo1 building products. It is inorganic, will not deteriorate, and can be handled by mechanical equipment with a minimum reduction of fibre length. The many physical properties peculiar to asbestos fibres should be well understood by the manufacturer. They may be briefly enumerated as follows: fibre strength, fibre composition, sliminess, length, harshness, softness, and filterability or porosity. This last named property is important and it is the purpose of this paper to present some basic studies on filtration as applied to production problems.

Jan 1, 1949

By Bill Almdal

Today?s presentation ? Role of the Regional Issues Working Group ? What does RIWG do? ? How can RIWG?s work benefit Stakeholders? ? Review of forecasts vs. reality ? How have past investment compared to the reality? ? Risks to future growth ? The growth potential is very high and so are the risks ? Examples of outputs ? Housing needs ? Growth in population ? Tires for large trucks The Regional Issues Working Group ? Our vision ? To provide a proactive process which promotes the responsible, sustainable development of resources within the Regional Municipality of Wood Buffalo for the benefit of all stakeholders ? What we do ? Facilitate planning for growth ? Facilitate effective and efficient resolution of issues ? Involve all of the resource developers and affected stakeholders in planning ? Develop plans for sharing benefits with Aboriginal stakeholders ? Benefits for Stakeholders ? Our forecasts include up-to-date information from all developers ? including information on employment and housing needs ? Our forecasts are the basis of planning for many stakeholders ? and can assist in their development planning

May 1, 2002

By D. Ingram

"PRIMARY DUST COLLECTOR A. 42,000 CFM James Howden Fan Z-6 Size 3650 Fan Dia 40"" HP 75It was found that the fan was not large enough to remove the air that was displaced by the trucks dumping. So it was removed and an enclosure was installed to isolate the gyro from the rest of the building.B. FANSJames Howden Fans Model RPM 3500 Series 357 FW HP 10These fans were installed when the first dust system was put into operation. It was found that the high RPM and extreme fan wear caused a major maintenance problem. These fans were replaced with Chicage Blowers Model SWS1 RPM 1180 Dia 36"".DRY CYCLONE COLLECTORS A.,Three four foot rubber lined cyclones. Four six foot rubber lined cyclones.All under flow. Water is controlled manually and gravity flows to a central sump box. From there it flows to the grinding circuit in the Mill.Cyclone under flow product runs between 100 and 200 tons of dust per 24 hours with a screen analysis 30% + 400.The cyclone under flow product is diluted to about 3 to 4%. Solids total gallonage approximately 400.B.,Elbair Wet Scrubber125 HP RPM 56042,000 CFM,Model PX861The Elbair collects the total product from the discharge. Of the Cyclone fans the under flaw goes to the Mill - the Elbair discharges stack goes to atmosphere.The Elbair wet scrubber had to be redesigned in order to keep it in service."

Jan 1, 1976

By P. W. Jensen

Gold deposits in Interior Alaska are commonly coincident in time and space with reduced, mid-Cretaceous granitoids. The True North deposit of the Fairbanks district is several km from such granitoids, but yields mineralization ages indistinguishable from the Fort Knox granite-hosted deposit. True North, however, resembles sediment-hosted epithermal Au, demonstrating the variability of intrusion-related Au deposits in metamorphic rocks. The True North deposit (14M tons at 1.5 gpt) is hosted within a carbonaceous thrust complex separating eclogite facies from amphibolite facies rocks, located > 5 km from mineralized granite outcrops. The ores contain anomalous Sb, As, and Hg (stibnite is the most common sulfide) with ankerite-sericite alteration in steep NE-striking ?feeder? shears and low angle thrust shears. Nearest hornfelsed rocks are located > 1 km away, and across several high-angle faults. Fluid inclusion data indicates trapping temperatures of ~250C from low-density, low-salinity fluids at P < 0.5 kb. Au was originally present as solid solution in sulfides; minable ores are restricted to the oxidized upper 100 m of the deposit. The considerable differences between this deposit and the temporally equivalent Fort Knox intrusion-hosted deposit indicate no one description adequately characterizes this deposit type.

May 1, 2003