Search Documents

By B. R. List, E. R. F. Lord

The Syncrude open pit mine, located near Fort McMurray in northeastern Alberta, produces approximately 410 000 tonnes of oil sand feed daily, which, after undergoing a bitumen extraction phase, generates approximately 315000 tonnes of tailings solids daily. The tailings are used to hydraulically construct containment dykes and supporting beaches of the storage facilities. Tailings deposition commenced in May 1978 with the commissioning of the Mildred Lake Settling Basin which is currently composed of approximately 600M m3of solid sand approximately 300M m3of contained fluids with fine tailings in suspension for consolidation. Two other storage facilities, commissioned over the past six years, have been developed to store sand and consolidated fine tailings referred to as mature fine tailings. Fine tailings reduction initiatives being developed will be successful in reducing future production of fine tailings volume by 20%. These initiatives include spiking (addition of fine tailings to coarse tailings lines for deposition), composite tailings (addition of gypsum to promote consolidation) and freeze/thaw dewatering, also to promote consolidation. The mandate of research efforts is to enhance tailings disposal and to develop economical and technically feasible reclamation initiatives. Final tailings landscapes will be geotechnically stable and ecologically productive to minimize or eliminate long-term liability. This technical paper will review the design philosophies of the current facilities and provide an overview of the areas of continuous improvement in the field of tailings management practices through the concerted research efforts and their implementation.

Jan 1, 1997

By Andrew J. Freyman, Graham T. Armstrong

"In September, 1968, a survey of operating mines in the Yukon and the Northwest Territories was undertaken to determine the role of Indigenes (Indian, Metis, Eskimo) on the mines, and the attitude of mine management to these employees. The operating mines in the Territories had (at that date) a total employment of 2,002 men, of which 91 (4.5 per cent) were Indigenes. Indigenes make up 45 per cent of the Territorial population (18 per cent in the Yukon and 63 percent in the Northwest Territories). The paper documents some of the problems associated with indigenous employment in mines. A study was undertaken to determine the role of Indigenes (Indians, Metis, Eskimos) in operating mines in the Yukon and in the North-west Territories. In addition to the mines north of the 60th parallel, the experience of several other Canadian mines was examined. The general picture obtained is considered to be representative of the Canadian mining industry."

Jan 1, 1969

By Carl Bertrand, Patrice Nadeau, Claude Bazin

"Rio Tinto Fer et Titane processes the ore extracted from the Lac Tio orebody to concentrate the hemo-ilmenite (FeO.TiO2-Fe2O3) mineral that is subsequently smelted to produce pig iron and titanium oxide slag. The ore is crushed, heat treated (roasted) and concentrated using dry magnetic separators. This paper describes a model to predict the magnetic susceptibility of the roasted ore and its behaviour in the magnetic separation plant. The model uses a classification of the ore as a function of the size and magnetic susceptibility of the particles. A subsequent division into mineral species allows the simulation of the magnetic separation process. The model is used to assess various operating options when process disturbances occur.INTRODUCTIONOre processing operations consist of ore size reduction followed by the recovery of valuable species in a concentrate that is subsequently sold for its minerals or metal content. The concentration processes are based on the physical and/or chemical properties of the minerals contained in the ore. Flotation is typically used to recover minerals of base metals such as copper, zinc, lead or nickel. Iron ore and other dense minerals are typically concentrated by gravity separation processes. Magnetic separation uses the magnetic properties of the minerals to concentrate magnetite and other minerals, to clean coal concentrate and to recycle ferrosilicon for dense separation processes (Brophy, 1985).Magnetic separators can be divided into low and high intensity separators and high gradient magnetic separators (Gillet, 2008). Most of the low gradient magnetic separators are built as rotary drums that are operated in wet or dry conditions. Dry magnetic drum separators are used by Rio Tinto Fer et Titane in Sorel-Tracy, Canada to concentrate hemo-ilmenite from the ore extracted at the Lac Tio Lake mine near Havre St-Pierre, Canada. The analysis of production data suggests that process improvement could be achieved by identifying key variables for the control of the magnetic separation circuit and/or by modification to the circuit flowsheet. The use of a process model was considered to be an effective approach to conduct a preliminary analysis of the circuit with a view toward process optimization. However, the literature contains few detailed studies dealing with the modelling of magnetic separation processes."

Jan 1, 2011

By Christopher R. Lattanzi

"Discounted cash flow analysis provides a means of relating the magnitude of expected future cash profits to the magnitude of the initial cash investment required to purchase an asset or to develop it for commercial production. The objectives of discounted cash flow analysis are to determine:.. The net present value of a stream of expected future cash revenues and expenditures... The rate of return which the expected future cash flows will yield on a given level of initial cash investment.In the case of mineral properties, discounted cash flow analysis is generally accepted as the preferred method of valuation, whenever sufficient data are available to permit its reasoned application. Sufficient data are required to support estimation of all of the individual elements of cash revenue and cash expenditure which will be associated with the development and operation of the property, up to the end of its estimated life. It is the accuracy of these input estimates which determines the validity of the resulting determinations of profitability and rate of return on invested capital.In undertaking any discounted cash flow analysis, it is important to recognize certain fundamental attributes of the mining industty:.. The basis of any mineral development is the existence of an ore reserve... Costs are determined by the number of tonnes mined and processed, while revenues are determined by the number of pounds or ounces of metal produced. The two are related by the recovered grade of the ore... Profit is typically more sensitive to changes in revenue than it is to changes in cost... Commodity price is a principal determinant of revenue, but it is also the factor with which is associated the greatest level of financial risk.In the end, of all of the factors which must be considered in the discounted cash flow valuation of a mineral property, the most significant are the reliability of the reserve estimate, particularly with respect to recovered grade, the price at which the product is to be sold, and the risk of not maintaining the projected level of price."

Jan 1, 2003

By G. E. Wittur

"The twenty-one members of the Organization for Economic Cooperation and Development, comprising eighteen western European nations plus Canada, the United States and Japan. account for two-thirds of world steel production. The Special Committee for Iron and Steel was formed by the OECD to study trends and problems in the steel industries of member countries. The paper begins with a summary on the Organization, including an historical sketch, its structure, member-ship and objectives. The steel industry of the entire OECD is briefly described before proceeding to a more detailed discussion of various aspects of the steel industries of European OECD members, emphasizing practices and conditions that differ from those in North America. Benefits to Canada of representation at meetings of the OECD Special Committee for Iron and Steel are described."

Jan 1, 1967

By Julie Culverhouse, Dennis Grimm, Kieran Harding, Jean-Francois Boulanger

"Agrium’s Canadian Phosphate Business (CPB) is comprised of Kapuskasing Phosphate Operations (KPO) in Northern Ontario, Canada’s only operating phosphate mine, and Redwater Phosphate Operations (RPO) in Alberta, which manufactures the fertilizer from KPO’s concentrate.Production from KPO’s South Pit commenced in 2009 and introduced contaminant problems: high aluminium from crandallite and kaolinite clays. These issues caused a drastic decrease in P2O5 recovery and throughput in both plants. KPO attempted to reduce Al clays by means of aggressive desliming. Meanwhile RPO experienced high amounts of dissolved metals in their feed that are detrimental to fertilizer production.This paper covers the mineralogy of the problem, its impact on contaminant separation at KPO, on RPO’s process and on Agrium’s Canadian Phosphate Business as a whole.Potential solutions to the problem are discussed and analysed, including a process change to deslime high aluminium streams more aggressively and high grade ore flotation, which is atypical at KPO. The latter is a demonstration of the value of communication between the concentrator and the client, as KPO accepted a recovery loss and increased production costs in order to increase overall CPB profits. General lessons learned are discussed, followed by a section on ore blending.INTRODUCTIONAlthough the existence of the Kapuskasing phosphate deposit has been known since the 1970s, it’s only since 1999 that Agrium has been operating the Kapuskasing Phosphate Operations (KPO). The mine consists of three major pits (Center, North and South) from which a mining contractor hauls the apatite ore to the Agrium concentrator. The beneficiation plant processes the ore, separating contaminants such as Fe, Mg and Al which are detrimental to its client, Agrium’s Redwater Phosphate Operations (RPO). The KPO concentrate is finally thickened, filtered and dried before being shipped by rail to RPO.At the Redwater plant, the KPO concentrate is added to a sulfuric acid solution in an attack tank, to create a phosphoric acid solution and gypsum:"

Jan 1, 2011

Optimizing production scheduling in open pit mines is important for managing cash flows of mining operations. This paper describes a new, probabilistic, mixed integer programming (MIP) formulation which has been developed to minimize the risk of not achieving planned production targets, in terms of metal production and ore tonnage feed for the mill during production, while considering maximization of total discounted economic value. The new MIP model also recognizes that to minimize movement of excavators over long distances and accommodate equipment access, the blocks scheduled for mining within a period cannot be spread too widely. The model is applied to a laterite nickel-cobalt deposit, as an example of multi-element deposits that have complex ore quality constraints. The results show that the proposed model generates feasible schedules. When compared with traditional optimization techniques, the new model is superior in terms of minimizing the risk of not meeting production targets, especially at the early stages of production, and in terms of generating practical scheduling patterns.

Jan 1, 2006

By H. E. Urtubia, C. W. Bailey

"BHP-Billiton’s Minera Escondida Limitada is one of the world’s largest copper producers. It treats a combined 88 million tons of copper ore per year through its two concentrators: Los Colorados and Laguna Seca. Over the past three years, metallurgical sampling has been performed at the Laguna Seca concentrator to calibrate both the JKSimMet and JKSimFloat grinding and flotation simulators. In the past, the calibrated simulators have been used to predict the effect of changes in operating conditions in the grinding and flotation circuits separately. To assist in the development of future processing options, predictions were required of the effect of changing grinding circuit conditions on flotation performance. This was achieved by using an integrated grinding and flotation simulation. The grinding circuit performance was predicted under different operating conditions (such as tonnage rate and product grind size) using JKSimMet, and these results were then used in JKSimFloat to predict the flotation performance for the new grinding circuit product. This combination of the simulators allows both the effects of residence time and grind size on flotation performance to be investigated.This paper presents the first combined grinding and simulation modelling and simulation case study using JKSimMet and JKSimFloat. The modelling and simulation methodologies for the grinding and flotation circuits are discussed along with the circuit simulations that were performed. The simulator predictions are presented in conjunction with independent laboratory results of the new operating conditions. The ability to predict flotation circuit performance based on changes in grinding circuit performance is also discussed. This methodology provides improved predictions of flotation circuit performance when grinding circuit changes (including grinding capacity increases) are made.INTRODUCTIONOver the past decade, the grinding and flotation research groups at the Julius Krutschnitt Minerals Research Centre - JKMRC (Brisbane, Australia), University of Cape Town (Cape Town, South Africa) and McGill University (Montreal, Canada) have been developing a methodology for optimising grinding and flotation plants using actual plant data together with semi-empirical sub-process models. The project is being conducted as part of the Australian Minerals Industry Research Association (AMIRA) P9 Project, titled “The Optimisation of Mineral Processes by Modelling and Simulation”. The project first commenced in 1962 and is currently in its “Nth” phase."

Jan 1, 2007

By M. Savich

A graphical method has been developed for the evaluation of the U.S. Occupational Safety and Health Act Noise Exposure Index and the Equivalent Continuous Sound Level. The method makes use of a noise survey form and a mechanical integrator with two sliders, and is less tedious and susceptible to error than alternative methods. The graphical method is adaptable to various codes for noise exposure and may be used with any instrument that measures noise level. One example of its application to a practical situation in a Canadian mine is given to demonstrate the procedure .

Jan 1, 1978

By Chris Bennett, Glen Kosick

"Process modeling and equipment sizing procedures for SAG circuits has advanced significantly over the past two decades. However, no matter how exact the hardness tests, models and scale-up calculations, if the ore samples being used for design do not accurately represent the orebody then major design errors can be encountered. This paper will describe a hardness testing method for identiQing the power requirement profile of an orebody, to an extent that design errors due to poor sampling can be greatly reduced or avoided altogether. It will provide some insight into the magnitude of hardness variability that can be encountered in an orebody. Finally, the paper will preview how detailed hardness distribution data can be incorporated into mine block models, to optimize SAG circuit design for an orebody, both fi-om a capital investment and throughput point of view.INTRODUCTIONIt has long been known that many SAG/AG' circuits experience wide swings in throughput. These throughput variations are almost always of a magnitude not anticipated in the plant design; consequently, they are detrimental to the expected return on investment for the mining companies. It is clear that the throughput swings are mainly caused by changes in ore hardness. In 1993, in an attempt to address this problem, MinnovEX began investigating the possibility of using a small scale SAG test (2 kg charge) to predict SAG power requirements from drill core samples. The objectives of the small scale test were to enable mining companies to do many more SAG hardness tests than currently undertaken for a particular orebody. To make this possible, the SAG tests had to use a minimal amount of sample, be cost effective, and give acceptable accuracy in the prediction of SAG power. If this small scale SAG test proved accurate, then the high sampling frequency would yield results that approach the true hardness distribution of an orebody. This hardness distribution could then be used to derive the distribution and variability of specific energy required throughout the complete orebody. This specific energy (kWh/t) can be thought of as the power required to grind one tonne of ore per hour (kW/tph) to a specified size. Once the true distribution of power requirement throughout the whole orebody is understood, the grinding circuit design team can make an informed decision regarding the hardness value that is most appropriate for sizing the SAG equipment. Throughput losses due to hardness variation could be deliberately planned for or avoided altogether (a capital cost decision)."

Jan 1, 1999

By T. Holmes, J. Middlemiss

"Agnico-Eagle (AE) has been operating their Kittila Mine in Northern Finland since 2008. The mine has experienced considerable ore flow problems with ratholing, bridging and freezing in their mill feed bin since start up. In the first winter of operation, the entire central portion of the contents of the cylindrical flat-bottomed 2000 tonne mill feed bin froze. Flow was erratic and could only be achieved through small diameter ratholes. To maintain a reasonable, albeit limited, feed to the mill, the bin had to be kept less than ½ full and a portable steam generator was brought in to melt the frozen agglomerates that frequently blocked the outlets. The combination of limited surge capacity and frequent outages required the crushing plant to operate 24/7 and resulted in inconsistent production levels and high operating costs.AE had planned to expand the processing plant to increase throughput by about 30% when they transitioned from open pit to underground ore. These plans presented an opportunity to improve the material handling.To avoid the problems experienced with the original mill feed bin, AE enlisted Jenike & Johanson Ltd. (J&J) to test samples of the ore, and based on the measured flow properties to provide design recommendations to ensure that the new mill feed bin would operate reliably. The new 2000 tonne expanded flow mill feed bin and apron feeder were installed in 2014 and are now supplying almost 93% of the total mill feed with the remaining coming from the original bin.IntroductionIn early 2009, AE engaged J&J to visit their then recently opened Kittila mine and mill in Northern Finland (Figure 1). Over the first half-year of operation, production had been restricted in the ore handling and storage system by flow problems such as ratholing, bridging and freezing including blockages of chutes and hoppers as a result of frozen fines buildup and large frozen agglomerates. AE wanted to increase production in the existing open pit mine and mill feed operation and also wanted to avoid similar ore handling problems when they commissioned the new underground mining system under development at that time."

Jan 1, 2017

"With the plethora of cable bolts on the market, geotechnical engineers can be baffled by the differences in performance claims from the manufacturers but perhaps more importantly they are sometimes at a loss in making an optimal selection matching behaviour with a particular site condition. To this end a new testing methodology has been developed that can cater for the varying types of cable bolt behaviours. The methodology is based on the laboratory short encapsulation pull test (LSEPT) as recommended in the British Standard and overcomes several deficiencies such as cable rotation. Of most significance however, is its inability to measure the post-peak residual performance of high load transfer capacity cables and consequently, there is an inference that these cables may be susceptible to sudden anchorage failure with relatively little yield. This paper details the results of anchorage performance tests of a range of cable bolts and the differences in performance with rock strength and drill hole diameter.INTRODUCTIONA research project was undertaken to develop a new laboratory-scale test apparatus to study the axial performance of fully grouted cable bolts that are used in the Australian underground coal mining industry. Work by Thomas (2012) and others in recent years found there were a number of deficiencies in the testing methodologies making it difficult to determine and compare the performance of the dozen or more different types of cable bolts on the market. This has meant that geotechnical practioners have been hamstrung in optimizing the design of ground support systems in underground environments that are increasingly more arduous.A cable bolt is a flexible tendon consisting of a quantity of wound wires that are grouted in boreholes at defined distances between holes in order to provide ground reinforcement of excavations (Hutchinson & Diederichs, 1996). They were initially introduced into the underground hard rock mining industry in the 1960s (Thorne & Muller, 1964) and since the early 1970s have been brought to coal mining operations."

Jan 1, 2015

The rock mass classification systems were developed for different functions, including support selection, excavation method selection and the determination of rock mass engineering properties for excavation design, among others. This explains in part why we have several rock mass classification systems. It is often cautioned that the rock mass classifications are to be used for preliminary excavation support design, but this caution is now often overlooked and detail/final support design based on the rock mass classification systems. This paper advocates differentiating between rock mass classification for pre-excavation support planning and rock mass classification for at-face excavation performance assessment. It is concluded that most at-face excavation performance problems are attributable to confusing the virgin rock mass rating with the rock mass rating on exposure during excavation, and that this observation is independent of the method of excavation. Procedures are then presented for virgin rock mass rating and for at-face rock mass rating/assessment during excavation.

May 1, 2009

By G. Azimi, K. K. Varanasi1, A. T. Paxson, R. Dhiman, H. -M. Kwon

Hydrophobic materials that are robust to harsh environments are needed in a broad range of applications. Although durable materials such as metals and ceramics, which are generally hydrophilic, can be rendered hydrophobic by polymeric modifiers, these materials deteriorate in harsh environments. Here it is shown that a class of ceramics comprising the entire lanthanide oxide series, ranging from ceria to lutecia, is intrinsically hydrophobic. Their hydrophobicity is attributed to their unique electronic structure, which inhibits hydrogen bonding with interfacial water molecules. In addition, this work demonstrates that these ceramics sustain hydrophobicity even after exposure to high-temperature environment (1000 °C for 2 h in air). It is envisioned that this class of robust hydrophobic materials will have far-reaching technological potential in various industrial applications, where water repellency and dropwise condensation are desirable.

Jan 1, 2014

By E. Gallestey, D. Groenveld, F. Kolb, M. Rozou

"Recent copper price evolution pushes modern mining industry even harder to achieve highest production with maximum efficiency. Operations are bound by numerous contractual and environmental conditions that bring a high degree of complexity to both the operators controlling the process and the plant managers assessing the circuit’s potential and setting the production goals.Advanced process control (APC) for grinding is one important tool to operate this most energy intense area in an optimal way, finding the optimal trade-offs between highest throughput, energy efficiency and product quality based on variable ore properties, production targets and management priorities.ABB’s state of the art control and optimization software platform enables user to design a controller based on model predictive control (MPC). The paper and the presentation show the technology used and the results achieved through an APC controller installed in a pilot project in Aitik (Boliden SA), Sweden. Furthermore, possibilities to interconnect grinding with other areas as stockpile management and flotation with various interconnected APC controllers will be shown. Finally, an example of the return on investment and the payback times based on the increased throughput and better product quality will be presented.INTRODUCTIONDepending on the ore characteristics and the targeted plant capacity, the design of the grinding circuit may vary significantly. Typically, the circuit consists of several mills (rod, ball, SAG, AG) in series and/or parallel with a number of classifiers and sumps at appropriate locations (see Figure 1).The main goal of the grinding section is to reduce the ore particle size to a level that enables efficient separation between gangue and precious metals in the subsiding processing step. The trade-off between quality and quantity has to be made. At the same time, it is also crucial to execute this process at the lowest possible energy and grinding media consumption."

Jan 1, 2015

By Jos. Kalbhenn

MR. G. G. BOWSER: Mr. Kalbhenn's paper is an excellent one and is a concise description of a very interesting piece of work. It is well known that a great deal of preliminary study was given to this job before the final plans were made. It is due to this thorough preparation .chat the work progressed so satisfactorily, smoothly, and safely. The ideas carried out in the construction of the hardwood pack, timbered compartment, inclined raise, loading chute, and steel-boomed room, all contributed to a successful conclusion of the work. The extra care in being certain that the compartment shafts were well timbered was especially necessary on account of the difficult blasting conditions. In other words, the foundations .of this job were well and truly laid. The blasting in this work was very difficult due to the nature of the Strata. Working under an ever precarious roof condition and completing .this job with only two lost-time accidents is a record of which to be proud. The shaft men engaged on this work are also due for praise. I regret I did not visit this work while it was in progress. It was not in lack of interest. This, however, more or less proves that the blasting end .of this job went along with practically no trouble. I have seen the nature of the rock, as I made several visits to the tunnels while they were being put through from the Phalen to the Harbour seam. According to figures in Mr. Kalbhenn's paper, the explosives consumption works out to 1.61 pounds per cubic yard of rock in the solid, or 0.8 pounds per ton. The explosives consumption in the tunnels ran from 2.86 to 3.46 pounds per cubic yard or an average of 1.58 pounds per ton of rock. Of course, the rock in the shaft was blasted in the most economical way possible, as far as powder costs are concerned, as the face advanced at close -wright angles to the strata and gravity was acting with the explosive. The tunnels were driven nearly 'end on' the strata and bottom holes had to be lifted, and I believe there was some re-drilling of ribs left in the floor. I would like to congratulate Mr. Kalbhenn on his very fine paper.

Jan 1, 1944

By T. Joseph, E. Zheng, M. Curley

"Hydraulic transportation efficiency and production optimization are considerations in the surface extraction of Athabasca oil sand deposits. To reduce the dependence on haul trucks, it is possible to extend the hydraulic transport system to production faces using a mobile at-face slurry system (AFSS). The flexible arrangement of connected pipelines transports slurried minerals from the mining face to the processing plant. An experimentally verified mathematical model indicates the friction loss of oil sand slurry associated with the AFSS. Laboratory-scale testing enables extended analyses for examining pipeline slurry transport in an oil sands environment.RÉSUMÉ L’optimisation de l’efficacité du transport hydraulique et de la production sont des considérations importantes dans le domaine de l’exploitation à ciel ouvert des gisements de sables bitumineux de l’Athabasca. Afin de réduire la dépendance envers les camions de transport, on envisage d’étendre le système de transport hydraulique aux fronts de taille à l’aide d’un système mobile de transport des matériaux sous forme de boue à partir du front de taille (AFSS, de l’anglais at-face slurry system). L’organisation flexible des conduites reliées permet le transport de minéraux à l’état de boue du front d’exploitation jusqu’à l’usine de traitement. Un modèle mathématique vérifié de manière expérimentale indique la perte de charge par frottement des schlamms provenant du traitement des sables bitumineux associée à l’utilisation de l’AFSS. Des essais en laboratoire permettent de mener des analyses approfondies portant sur le transport de boues dans des conduites dans un environnement de sables bitumineux. INTRODUCTIONObjectives and scope of studyThe at-face slurry system (AFSS) concept has become a competitive means for materials handling to optimize haulage system efficiency and cost. The mobile and flexible arrangement of the AFSS introduces a unique set of hydraulic transport problems. This paper will focus on developing the mathematical models governing the friction and head losses within the AFSS concept.Background of the problemLarge-capacity shovels and dump trucks are increasingly used for excavation, loading, and hauling in the operation of surface mining. Production cost and efficiency optimization are demanded during the Athabasca oil sands (Alberta, Canada) mining process to secure North America’s energy supply. Increasing haulage distances, rugged terrain, and a constrained mine environment are conditions that will reduce the effectiveness of the shovel-truck haulage system (Frimpong, Szymanski, & Changirwa, 2003). In such conditions, the tire heat index and weight, distance, and time limits for truck haulage can be exceeded, simultaneously creating extreme tire wear and high maintenance costs. In addition to low production cost and equipment effectiveness, a mining environment also requires efficient waste-material recycling and distribution. Waste materials need to be recycled from the processing plant to a new destination such as a tailings dam, or replaced in mined-out areas such as backfill. The Athabasca oil sands configuration and location characteristics result in a mining environment that would benefit from flexible pipelines for constant production and an efficient waste-material recycling process."

Jan 1, 2017

By P. Toscano

The objective of this investigation was to determine how the losses of nickel, copper and cobalt in fayalite slags could be controlled for nickel mattes with iron contents below 5 wt%. Laboratory-converting and slag-cleaning experiments were carried out at 1250°C. Several variables were investigated during and after converting to help minimize the amount of nickel and cobalt that reports to the slag. The variables used were oxygen concentration in the blast, coke breeze addition and nitrogen injection stirring. In all the experiments, slag and matte co-existed. Coke additions during converting have little effect on the losses of nickel, copper and cobalt. In fact, coke additions retard the converting process by consuming some of the oxygen injected. On the other hand, coke additions and nitrogen injection applied after converting was completed resulted in decreased slag losses.

Jan 1, 2004

By P. Toscano, T. A. Utigard

"The objective of this investigation was to determine how the losses of nickel, copper and cobalt in fayalite slags could be controlled for nickel mattes with iron contents below 5 wt%. Laboratory-converting and slag-cleaning experiments were carried out at 1250°C.Several variables were investigated during and after converting to help minimize the amount of nickel and cobalt that reports to the slag. The variables used were oxygen concentration in the blast, coke breeze addition and nitrogen injection stirring. In all the experiments, slag and matte co-existed.Coke additions during converting have little effect on the losses of nickel, copper and cobalt. In fact, coke additions retard the converting process by consuming some of the oxygen injected. On the other hand, coke additions and nitrogen injection applied after converting was completed resulted in decreased slag losses."

Jan 1, 2004

By Tony Breuer

Can international development NGOs and the mining industry find common ground and work together in the Third World? The Canadian Hunger Foundation/PARTNERS in Rural Development (CHF-PARTNERS) has, over the past forty years, implemented more than 800 rural community development projects in some 38 countries of Africa, Asia, and the Americas. Working with or for the Canadian mining industry offers both opportunities and risks. We can help a mining company ensure that the workers, their families and communities share adequately in the economic and social rewards from a mining operation in their area. We can contribute to the provision of sustainable livelihoods when an operation winds down. The company?s reputation as a good corporate citizen can be enhanced. On the other hand, mining companies and NGOs have generally very different values and missions. The risk of misunderstandings from conflicting motives and work practices is correspondingly high. Both partners must state their values and expectations clearly at the start of collaboration. The NGO must ensure that the company abides by acceptable ethical standards. It must not directly or indirectly subsidize a private company from its charitable donations. The mining company must satisfy itself that the NGO has the capacity, resources and experience to produce the results expected.

May 1, 2001