Search Documents

By D. Marcotte

The Rock Quality Designation (RQD) is a standard scalar measure of rock quality used in common rock mass classification systems (e.g. RMR, Q system). RQD is measured along diamond drill holes. RQD interpolation between holes is nontrivial. Despite the inherent limitations of drill hole data and the local complexities of structural geology, it is often the only information available for mining and major civil engineering projects. Therefore, maximizing the usefulness of this data is warranted. We derive a correction for directional effects that help reduce the bias and improve the accuracy of the estimations. The correction is derived with the aid of numerous simulations. It relies on simple information, the angle between the joint normals and the borehole axis (JO). A reference direction is identified as the borehole direction with smallest JO. A multiple linear regression model based on JO statistics in the various boreholes defines the correction model. The corrected RQD values are then interpolated. It is shown the method enables reducing the bias on RQD estimation by 50% and improves the accuracy of the estimates by 30%. The corrected RQD values show stronger spatial continuity than the raw values. The benefits of estimating the RQD indirectly by using joint frequency measures are also assessed.

May 1, 2003

By Yeonuk Choi, Gus Van Weert

"In regular CIL circuits, activated carbon is used for two purposes: avoiding solid/liquid separation after cyanide leaching, and minimizing gold losses in the tails. The carbon distribution and gold profiles in the successive CIL stages are operating variables, not objectives. When the CIL feed contains a preg robbing constituent however, such as native carbon, there will be competition for gold cyanide and this conflicts with minimizing of losses of gold to CIL tails. This paper examines some of the limitations of activated carbon in CIL circuits handling preg robbing Carlin Trend ores.INTRODUCTION Carbon-In-Leach (CIL) has been a great success treating regular gold ores, but the technology is still challenged by preg robbing feedstocks. Little information is available in the gold milling literature on CIL gold extraction from “free” milling gold ores which are preg robbing, or on autoclave discharge (POX’ed) slurries of double refractory ores. Neither feedstock is readily available for experimentation. No literature reference could be found describing deliberate modifications to CIL operations or CIL circuits due to the presence of two types of carbon: “native” and activated. There is some literature on the gold cyanide adsorption activity of native carbons (Schmitz, Duyvesteyn, Johnson, Enloe & McMullen, 2001). Various tests have been devised to measure this activity, commensurate with CIP and CIL practices (Tretbar, Arehart & Graves). In this paper, the term “native” carbon indicates (severely) preg robbing carbonaceous materials found in gold ores. There is considerable literature on the gold cyanide adsorption activity of man-made “activated carbons”. Various tests have been devised to measure this activity, commensurate with CIP and CIL practices. These tests are comparative, i.e. results relate to a standard carbon and depend on the test methodology and carbon history. The test results are equilibrium oriented, hence of limited value to CIL circuit designers or plant operators handling preg robbing solids; in CIL circuits most carbons are not loaded to capacity. Information on gold cyanide adsorption and desorption kinetics might be more relevant and that is one subject explored in this paper."

Jan 1, 2012

By Lori Kormos, Jhonny Carrión De la Cruz, Dominic Fragomeni, Elizabeth Whiteman, Jorge Oliveira

"Process diagnosis, flowsheet design and optimisation are most effectively and efficiently achieved through the use of metallurgical testwork combined with more modern quantitative mineralogical techniques. Integration of the mineralogical data in testwork programs provides a resolution that cannot be obtained from assays alone and can direct the flow of work to result in optimized conditions more quickly than would otherwise be possible. At Xstrata Process Support (XPS), QEMSCAN (Quantitative Evaluation of Materials by Scanning Electron Microscope) and EPMA (Electron Probe Micro Analyser) information can be employed to diagnose specific issues in a plant or lab scale test and are routinely combined with other metallurgical data sets to benchmark performance, design and optimise flowsheets. Representative sampling protocols for ore bodies or test products, the use of geometallurgical unit classification and high confidence metallurgical test programs are key components of the strategy. Two case studies from Xstrata Zinc’s Antamina Mine and Concentrator in Perú, and Xstrata Nickel’s Nickel Rim South Mine in Sudbury are described to show how the use of quantitative mineralogy were used to diagnose a plant issue and how the data can be integrated into metallurgical programs to assist mineral processing engineers to design and optimise flowsheets.INTRODUCTIONOver the past decade, there has been a shift away from metallurgical testing that employs only chemical assays to quantify performance; the use of empirical observation in order to optimise a flowsheet; and the extraction of bulk samples for testing or piloting. The integration of geological information into the planning and execution of testwork programs including the use of quantitative mineralogy has improved the overall quality and predictability of metallurgical programs. At the same time, improvements to metallurgical testwork protocols such as rigorous statistical assessment of results, the use of factorially designed experimental strategies (DOE), and replicate flotation with appropriate quality controls, has improved the confidence level in these results.Process diagnosis, which utilizes quantitative mineralogy, can clearly define the root cause of the metallurgical issue. Whether used on its own to diagnose an issue or in combination with other metallurgical testwork, the use of mineralogical data has become the standard in the mining industry."

Jan 1, 2010

By J. Dionne

"Next to the actual mine of Les Explorations Muscocho Ltée in Montauban, Quebéc, you could find a total of 364 000 tons of flotation tailings assaying 1.4 Au g/t et 82 g Ag/t to the south of the municipality. This tailings pile is what is left of previous operations. Preliminary leaching tests on these tailings in laboratory columns gave interesting results which led to tests in larger columns in 1984 and to a pilot test on a 750 ton heap in Montauban during the summer of 1985.This paper briefly describes the columns tests performed at the Centre de Recherches minérales and the heap leaching test designed and conducted by SOQUEM in Montauban. It also presents the results obtained.RESUMEPrès de la mine actuelle de Les Explorations Muscocho Ltée à Montauban, Quebéc, se trouvent, au pied du village, 364 000 tonnes de rejets de flottation titrant environ 1,4 g Au/t et 82 g Ag/t. Ce tonnage de rejets représente ce qui reste de l'opération des anciennes mines de Montauban.Des essais préliminaires de lixiviation en colonne sur ces rejets ont donné des résultats encourageants. Ils ont été suivis en 1984 par des essais en colonnes plus volumineuses et par un essai pilote à Montauban en 1985 sur une pile de rejets de 750 tonnes.Ce te x te donne une brève de script ion des essais en colonne effectues au Centre de Recherches minérales et de l’essai pilote planifie et exécute à Montauban par SOQUEM. Il présente les résultats obtenus."

Jan 1, 1987

By R. Dahlke, J. A. Finch

A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick mine concentrator to investigate the role of gas (air) superficial rate (Jg) distribution to the cells in the final Zn cleaning stage (bank of seven cells), i.e. the Jg profile. Three profiles were tested: “balanced” (each cell with same Jg), “increasing” (from cell 1 to 7 proportionally), and “decreasing,” along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was the response of the first cells in the bank where the increasing profile gave the highest selectivity of sphalerite against nonsulphide gangue (NSG). The other profiles gave lower selectivity and higher zinc recovery in the first cells, which combined to reduce overall bank performance. The higher selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG. The increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.

Jan 1, 2004

By Ken Dyck, Chuck Edwards

"Cameco's McArthur River is the world's largest high grade uranium mine. Production started in late 1999. Cameco carried out the engineering design and construction management for the McArthur River project, including all aspects of mining, ore handling and ore transportation. The ore composition was expected to vary dramatically (0 to 30% U3O8; 0 to 25% clay; etc). To cope with the composition swings, sizing screens were selected to provide classification in the grinding circuit. The grinding circuit started up close to the design to provide minus 500 micron slurry. The 50% solids (wt) ground ore slurry proved to be difficult to transport to and process at the Key Lake Mill. Slurry containing high concentrations of high density pitchblende (about spgr 8.0) and low concentration of stabilizing clays, would settle in containers. Ore transport efficiency to Key Lake was found to be unacceptable.A test classification cyclone was installed in the grinding circuit at McArthur River early in 2002. The cyclone operating parameters were not typical, but the cyclone was made to work very successfully. Transportation efficiency to Key Lake increased due to more stable slurry. Preferentially ground (fine) pitchblende particles were easier to leach at Key Lake. The radiation exposure for operators and maintenance personnel to handle the more stable slurry was also reduced.The classification sizing screens were removed from the McArthur River grinding circuit and replaced by permanent classification cyclones late in 2002.INTRODUCTIONThe McArthur River mine and Key Lake mill operations are located in northern Saskatchewan, approximately 650 and 720 kilometres from Saskatoon, respectively. Figure 1 is a location map. McArthur River is the world's largest, high-grade uranium mine, with a production capacity of 18.7 million pounds U3O8 annually. (Rosner and Edwards 1998, Dyck 2000, Jamrozek 2000, Rodgers 2001) Proven and probable reserves are more than 473 million pounds U3O8. McArthur River ore, grading on average 21% U3O8, is milled at Cameco's Key Lake operation, 80 kilometres southwest by road. McArthur River production began in December 1999."

Jan 1, 2004

"The standards set out requirements of the Toronto Stock Exchange for company’s providing information to investors, regulators and/or the media regarding their mineral properties. In addition, information contained in new releases, continuous disclosure documents [annual report], or other forms of communication [printed investor relations materials and electronic publications] are also subject to these standards.1.0 INTRODUCTIONThe disclosure of the results of exploration and development activity on mineral properties mustcomply with the requirements of the Toronto Stock Exchange Policy Statement on Timely Disclosure, theOntario Securities Act and all applicable policies and rules of the Ontario Securities Commission and anyother securities regulatory body having jurisdiction over an issuer listed on the Exchange. In particular,the requirements of National Instrument 43-101 must be followed.The purpose of the standards is to set out the requirements of the Toronto Stock Exchange when acompany provides information to investors, regulators and/or the media regarding its properties, whethersuch information is contained in a news release, a continuous disclosure document such as an annualreport, or other form of communication, including, but not limited to, printed investor relations material andelectronic publications such as Internet Web sites. These standards do not apply to prospectuses orlisting applications, the standards for which are contained in the policies and rules of the securitiescommissions and the Exchange. These standards are also not intended to establish requirements for thecontent of technical reports.Any information published by or on behalf of a company must comply with these standards. If acompany becomes aware of information published by others regarding its mineral properties which ismaterially misleading to investors, it should take appropriate action to correct such information orotherwise make it known that it is not responsible for publishing such information and does notnecessarily agree with such statements.Disclosure concerning mineral properties should identify the ""qualified person"" as defined in NI 43-101 who is responsible for the work conducted on the property and such person shall have read andapproved of the technical disclosure."

Jan 1, 2003

By A. K. Watt

"The availability of fresh water to meet present and future needs in Ontario is of concern to an increasing number of people. Rain and snow are the source of our potable water and provide, on the average, some 180,-000 billion gallons of water annually. This amount is reduced to 94 billion gallons a day as a result of the evaporation and transpiration of water and our inability to construct the necessary reservoirs for capturing surplus stream flow.The water used for domestic, irrigation, public supply and industrial purposes amounts to some 7 billion gallons daily at present and will reach 21 billion gallons daily by the year 2000; however, only about one-fifth of the water used is actually consumed, and this, along with the possibilities of water re-use, improves the water supply picture still further.The need for adequate pollution control has accompanied industrial and urban expansion and is an important factor in the extent to which our surplus water is used. In the 10-year period since the formation of the Ontario Water Resources Commission, the cost of water and sewage works constructed in the Province has exceeded one billion dollars. A special effort is now being made to control the industrial pollution situation.Numerous federal and provincial agencies are engaged in hydrologie studies in the Province, providing in-formation of benefit to those involved with water resources management."

Jan 1, 1967

By Alan D. Akerman

This paper describes the significant advantages and improvements in operational availability, reduced breakdowns, and overall cost reductions that can be achieved through the application of a Reliability Centred Maintenance (RCM) program, including Condition Based Maintenance (CBM) and Equipment Health Monitoring (EHM), in a mine environment. It uses a case study to illustrate the essential elements that constitute the basic requirements to establish such programs. This CBM case study analyzed the Load-Haul- Dump (LHD) vehicle sub-systems and their dominant failure modes, as a precursor to the development of condition indicators. The case study describes a disciplined process to enable condition indicator development and qualification in support of a CBM program. The identified condition indicators vary from readily applicable off-the-shelf monitoring systems and techniques, through to "leading edge" technologies that require further research and development. The paper also explores the developments that have been made in the combination of expert system software associated with modern computer based control systems, and the availability of "intelligent? sensor technology that complement the control system capability.

May 1, 2002

By T. Fekete, D. L. Flocks, R. T. Hart

The plugging effect of bacteria was investigated by injecting various concentrations of dead bacteria cells though sandstone cores. Pressure profiles along the cores were recorded periodically during the injection cycles. The plugging effect was analyzed using a plot of the ratio of reduced permeabilities to the initial permeability versus input volume. Results indicated that Tock permeability has little effect on plugging, but that the concentration of bacteria in the injection water has a significant effect on plugging characteristics. The pressure profile curves showed that bacteria penetrated several inches through the core but that the greater portion of the bacteria accumulated at the in-put end of the core.

Jan 1, 1960

"HPGRs operate in a wide array of applications in mining and minerals. These range from relatively coarse crushing of copper and gold ores at one end of the spectrum to the processing of fine iron ore pellet feed and fine industrial mineral products at the other. Traditionally these circuits involve the treatment of relatively moist materials in pre-grinding circuits; using single stage HPGRs in open circuit or as a closed circuit operation with screening or partial product recycle. More recently, HPGR is increasingly deployed in dry grinding in combination with air classification. The high throughput demonstrated by larger HPGRs has stretched the application towards coarser size reduction duties for a number of new projects. At the same time, the basic principle of inter-particle crushing for generating a product with a high fines proportion gives ground to investigate applying the technology further towards finished product duties. The advantages that HPGR brings are clear. Multi Stage grinding enables energy efficient size reduction across more of the comminution circuit. Primary HPGR serves for a coarse grinding duty, whereas a secondary HPGR is geared towards generating a fine product for downstream processing or even a finished product. This publication summarizes some of the features of staged HPGR circuits and discusses some examples of operating and projected applications.INTRODUCTION In most HPGR applications, the grinding units are used as a single process stage, either in open circuit, such as for pebble crushing [Rose 2002, Westermeyer 2000, Van der Meer 2015] or in closed circuit with classification [Van der Meer 2009, 2012] or product recycling [Van der Meer 2010]. Where a higher plant capacity is required, the HPGRs are commonly installed in multiple lines in a parallel arrangement [Parker 2005, Koski 201, Vanderbeek 2006]. HPGRs can take a wide range of feed size distributions, and grind this down to a product with a high fines content. In general view, there is a limit on the size reduction range that even an HPGR can provide. Grinding down from a very coarse ore (e.g. 70-100 mm) to a very fine product (e.g. 100 microns range) is stretching the ability of a single stage HPGR circuit. Fine grinding generally requires a classification stage that returns the classifier oversize to the head of the HPGR circuit. From one point of view, it can be demonstrated that when recycling a large proportion of fines and middlings back to the HPGR feed results in an effective feed with an overrepresentation of middlings and fines, which will eventually reduce the grinding efficiency and consequently result in an increased recirculation mass flow [Van der Meer 2014]. From another point of view the large recycling mass puts a strain or even a limit on the capacity of present-day conveyor capacity."

Jan 1, 2018

By Gaston Gendreau

CETTE PRÉSENTATION traitera des différentes phases des opérations de la mine du Mont-Wright depuis ses débuts jusqu'à présent. A une brève description de la géologie du gisement, suivra un exposé des méthodes d'exploitation de la mine et du genre d'équipement utilize.

Jan 1, 1977

By Takashi Nakamura, Atsushi Iizuka, Yong Fan, Etsuro Shibata

Magnetic separation of precipitated magnetite as iron resources in copper slag is one of the potential effective ways to recycle the slag. It is preferable to convert molten fayalite slag after copper smelting process to magnetite slag via oxidation. With a TTT (Time-Temperature-Transformation) diagram, the crystal composition of the slag obtained after air isothermal oxidation could be estimated through a designed cooling path. The crystallization behaviors concerned with molten oxidation was studied for better understanding of the trade-off relationship between magnetite and hematite during molten heat treatment. Moreover, a brief consideration was implemented of the reaction mechanism.

Jan 1, 2014

By Michel Doyon

Canadian Context: Exploration ??Space Exploration is within the unique mandate of the Canadian Space Agency ??Global partnerships ??Maintain close relationship with our partners ??New knowledge in S&T ??Retain and attract highly qualified personnel ??Participation in missions leads to design roles in industry and academia ??Collaboration between government laboratories, industry and academia

May 1, 2009

By J. I. Mathis

"The failure that was utilized for developing this model was a double bench-scale failure, approximately 20 m in height, in the Misery pit at BHP Billiton’s EKATI mine site. The bench that failed was excavated in biotite schist. Due to previous problems with bench-scale toppling failures, this bench was excavated with a 70° inclined, 30 m deep preshear. Upon exposure, the wall was very clean with half-barrels commonly observed from the pre-shear operation.In August 2003, a bench failure of about 1000 t occurred in this pre-sheared biotite schist (Fig. 1). Upon examination it was noted that the foliation that paralleled and dipped at 70° into the face when excavated was approximately horizontal at the top of the failure (Fig. 2). While the failure mode itself appears complex, the failure was apparently driven by three factors:• a low-angle, low-frictional strength fault or discontinuity at the base of the failure area;• water either contributed meteorically from precipitation and/or from permafrost melt; and• foliation planes providing a viable toppling geometry once toe block motion began to occur.The above details are illustrated in Figure 3.After considerable thought and analysis, a model was postulated for the failure.It is thought that the entire failure had been triggered by displacement of a toe block (Fig. 4). This toe block is bounded on the back by foliation, the bottom by a low-angle, lowstrength fault, and the front by the bench face. Water pressures behind the bench face developed forces on the block as can be seen in Figure 5. These forces were sufficient to induce block motion. As can be seen in the relative shear strength diagram in Figure 6, only a small amount of water is necessary in the face to initiate block displacement. Note that in this figure, a simplistic piezometric pressure distribution was assumed."

Jan 1, 2004

By F. Hassani, K. Moozar, J. Ouellet, P. Gauthier

"This paper describes a sudden spill of waste rock used for backfilling from a waste pass at an underground mine in Canada, thus causing a major failure/accident. The mine operator immediately launched a detailed investigation to understand the causes of this accident and develop procedures to prevent any recurrence of such events in the future. The authors from McGill University were invited to collaborate with the engineers at the mine to examine this accident. The events leading to the accident were studied, appropriate measurements were taken and samples of the waste material were collected for further testing and analysis.The field visit and the interview of the witnesses allowed the detailed documentation of the events. The sequence of events related to the incident, along with the experimental results obtained in the course of the investigation, are presented. The waste material was characterized in the laboratory with regard to its behaviour in the presence of water. This information is discussed and the failure mechanism involved in the accident is identified. Finally, the full recommendations as well as the immediate operational measures implemented by the mine to prevent the future occurrence of such events are presented and discussed."

Jan 1, 2004

By Javier Linares García

At then end of this year will be 10 years of producing concentrate for Antamina. This is a summary of what occurred over the last decade to increase production and tonnage above the design tonnage of 70,000 tonnes per day, up to an average of 100,018 tonnes per day in 2010, an increase in production of 42.9%. Equipment currently in use is the originally installed equipment, signifying a meaningful increase in capacity without capital. In this paper, the different phases of improvements and the realization of their impacts in chronological order will be outlined. Figure 1 below shows the average daily tonnage processed each year (tonnage throughput each year/calendar days), as well as the percentage increase over the tonnage of design.

Jan 1, 2012

By Dong-kil Lee

Field tests have been conducted to investigate the characteristics of flow and physical chemistry of acid mine drainage(AMD) in the Hwangji-Yuchang settling pond in south Korea. pH and ferrous concentration of AMD flowed in the settling pond is 6.79 and 25.5 mg/l, respectively. As a results, we found that the ferrous oxidation reacted strongly around the inlet of the pond and the distributions of physicochemical properties is depended on flow characteristics and ferrous oxidation rate of AMD.

May 1, 2011

By V. N. Bryant

"1.0 SYNOPSISThe Colomac property, located 137 miles by air northwest of Yellowknife in Canada's NWT. will recover gold from 10,000 tons per day of open pit ore.The decision to proceed with the project was based on a mineable ore reserve of 16 million tons (including dilution) averaging 0.064 oz/ton. After an in-fill drilling program in the latter half of 1988, Colomac's mineable, proven and probable ore reserves were increased to 28 million tons averaging 0.056 oz/ton of gold.A feasibility study completed by Wright Engineers for Neptune Resources in December 1987 examined the possibility of vat leaching followed by C.l.P. and electrowinning. A second feasibility study completed by Wright in February 1988 demonstrated that a conventional agitated leach circuit using a finer grind justified the higher capital cost of this process. This study was accepted and formed the basis of the project authorization.Preliminary engineering commenced in April 1988 and detailed engineering was started in September of that year with the objective of a mine/mill start-up by early 1990.The short time period available to meet the project deadline was additionally challenging, as site access is either by plane year round, and winter road from early February to late March. Normal lead times for equipment design, specifications, quotations and bid analyses were not possible, if the winter road time-slot was to be met."

Jan 1, 1990

By L. Flett, S. Woods, C. Deredin

"Following a significant reduction in world Imperial Smelting Furnace (ISF) capacity from 2003 to 2008, a major optimization initiative was successfully carried out on the lead upgrading and bulk (zinclead) flotation circuits in the Brunswick Concentrator.This paper describes the process improvements that have taken place in order to reduce the quantity of bulk concentrate:•,Increase in lead upgrading rougher flotation circuit capacity•,Installation of a closed-circuit bulk regrind utilizing MillPebs and 150 mm Cavex hydrocyclones•,Installation of two additional cleaner flotation stages on the bulk circuit•,Optimization of the manipulated variables in the lead upgrading and bulk circuitsINTRODUCTIONThe Brunswick Mine (Xstrata Zinc Canada) is located near Bathurst, New Brunswick and is one of the world’s largest lead/zinc mines. Milling of ore commenced in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 open pit mine. The planned closure of the mine will take place at the end of the first quarter in 2013. The ore is a complex massive sulphide, consisting of approximately 20% valuable minerals, 60% pyrite and 20% silicates.A simplified flowsheet for the concentrator is given in Figure 1. The overall flowsheet involves SAG milling, secondary ball milling, selective flotation, and dewatering by thickening, filtering and drying. The complexity of the flowsheet evolves from the requirements for fine grinding and the production of four concentrates: zinc (sphalerite), lead (galena), copper (chalcopyrite) and bulk (sphalerite plus galena).Primary hydrocyclone overflow feeds the copper-lead aerator-roughers for flotation at pH 9.0 with soda ash. Plant xanthate (80-20 sodium isopropyl and potassium amyl) and AP407 are used as collectors in the copper-lead circuit. The rougher concentrate is directed to the copper-lead regrind circuit and the tailings are fed to the secondary grinding circuit. The secondary hydrocyclone overflow from the secondary grinding circuit feeds the copper-lead rougher-scavenger banks. Rougher concentrates are reground to a P80 of 28 µm prior to three stages of copper-lead cleaning. The first stage of cleaning is done in an open circuit with the tail reporting to the cleaner scavenger. The cleaner scavenger concentrate reports to the regrind circuit and the cleaner scavenger tail combines with the rougher/scavenger tail to feed the zinc circuit. The second and third stages of cleaning are performed in closed circuit with the cleaner tail being recycled to the copper-lead regrind circuit. The average final concentrate grades 23% Pb, 3% Cu and 704 g/t Ag, and is fed to the copper separation circuit."

Jan 1, 2013