Search Documents

The purpose of this paper is to present the methods used in ground water control and the considerations that affected the development of these techniques. Production at Knob Lake is currently proceeding at depths which may be as much as 200 feet below the original standing water table. In order to produce a more saleable product and to improve operating and maintenance conditions, it is necessary to depress the water table below the mining level. Considerable success has been achieved by drilling deep wells in strategic locations and installing vertical tur-bine pumps at depths of up to 400 feet. This method is especially suitable for operation under severe winter conditions and has reduced the detrimental effects by a far greater extent than other methods of water control, Spring runoff is handled in open sumps, but all other water from four mines, with flows exceeding 16,000 g.p.m., is pumped all year 'round from about thirty-five wells. THE Knob Lake operation of the. Iron Ore Company of Canada is located on the Quebec-Labrador border, 320 miles north of Sept-lies, a seaport

Jan 1, 1965

By P. Babak, E. Insalaco, O. Babak, P. Henriquel

"Detection of outliers is an important primary step in geomodelling. Geological datasets often contain errors due to problems such as measurement device limitations and recording glitches. In this paper, a robust Mahalanobis distance–based approach is successfully applied to particle size distributions of the Joslyn lease, an oil sands development site near Fort McMurray, Alberta, Canada. Automatic outlier detection and geological review were combined. Outliers from the Mahalanobis distance approach were compared with their respective core photographs to determine if laboratory measurements and facies classification were correct. A checking procedure for laboratory technicians is proposed.RÉSUMÉ La détection des valeurs aberrantes constitue une étape primaire importante de la modélisation géologique. Les ensembles de données géologiques contiennent souvent des erreurs en raison de problèmes tels que les limitations des instruments de mesure et des pépins d’enregistrement. Dans le présent article, une méthode robuste basée sur la distance de Mahalanobis a été mise en oeuvre avec succès aux granulométries du bail minier Joslyn, un site de sables bitumineux en développement à proximité de Fort McMurray, Alberta, Canada. La détection automatique des valeurs aberrantes a été combinée à une étude géologique. Les valeurs aberrantes de la méthode de la distance de Manalanobis ont été comparées avec leurs photographies respectives de carottes de forage afin de déterminer si les mesures en laboratoire et la classification des faciès étaient correctes. Une procédure de vérification pour les techniciens de laboratoire est proposée."

Jan 1, 2015

By Alireza Golabchi

The AEC (Architecture, Engineering, Construction) industry is an information intensive industry and all related processes employed during different phases of a project, including planning, designing, building, manufacturing, occupying, and maintenance, involve vast amounts of data that is used for a wide variety of purposes. Building Information Modeling (BIM) is a powerful shared knowledge resource which stores this data to support decision making about a facility through all these different phases in its life cycle. Nowadays, BIM is mostly used in the design and construction phases while it can also be highly beneficial beyond those stages. For example, in the Operation and Maintenance (O&M) phase, BIM could be used for automated facilities management or robotic inspection to provide semantic knowledge for navigation. For any implementation not related to the original intent of the BIM (design), organizations need to be able to represent their project data in a common interpretable form, which provides the possibility of an accurate exchange of data among different software products and platforms, known as interoperability. This study has investigated the current state of interoperability between software products used as Building Information Modeling tools. The main focus has been on a popularly used format for BIM models, Industry Foundation Classes (IFC), since it has been specifically developed to enable standardized data exchange. The research methodology involved a comprehensive literature review and the gathering of all fragmented prior research related to the field in order to develop a consistent understanding of the current state of knowledge. This was accompanied with a detailed case study that evaluated and compared two dominant pieces of BIM software, Revit and Bentley, and examined their interoperability strengths and weaknesses while using the IFC format.

Aug 1, 2013

By Derek V. Ellis, Jack L. Littlepage

"Marine ecosystem effects ar1smg from the discharge of man-generated wastes to the sea can be schematized as: acute poisoning, chronic poisoning, enrichment, suffocation, temperature effects, salinity effects, toxin bio-concentration, changed production rates and changed species equilibria. A professionally designed site-specific monitoring program to check for such effects can not only safeguard the marine ecosystem from degradation, but it can also protect the industry involved from unanticipated remedial action after expensive construction has been undertaken. Monitoring programs should consist of three steps. Step 1 is an ecosystem survey which should be undertaken prior to final design of the discharge system and submission of applications for permission to discharge, because there can be considerable cost savings in obtaining information at an early stage in development. Step 2 involves location of the effluent field at the time of starting discharge, and analysing its dispersal behaviour. Step 3 consists of ecosystem monitoring with sampling stations and specific tests based on the accumulated prior information."

Jan 1, 1972

By S. S. Burns

"AbstractShovels of 18 cubic yard capacity and larger are described which incorporate advanced technology and techniques providing performance and operation tailored to meet the needs of open-pit mining.To achieve the goal s of increased production at lower cost with consideration of maximum availability, lower energy consumption per ton and low •impact on pit power, Harnischfeger Corporation developed a solid -state drive system (""Electrotorque"" - P&H trademark) and applied unique transmission methods.To date, more than 250,000 hours of experience in different parts of the world under varying operating and environmental conditions has proven that the ""Electrotorque"" shovel is the shovel of the future, today.This paper will discuss the electrical features and touch briefly on some mechanical features.Introduction to ""Electrotorque""THE hoist, crowd, propel and swing machinery of an electric mining shovel are driven by direct-current motors.A D.C. motor is used instead of an A.C. motor because the torque output per ampere input is at a maximum and the fact that it is doubly-fed (armature and field ) provides optimum flexibility in control.The power that is available in the pit is alternating current power. It is therefore necessary to change or convert this A.C. power to D.C. power so that the D.C. motors can be used."

Jan 1, 1977

By Corinne Boone

CO2e.com, LLC - launched in November 2000 - aims to be ?the global hub for carbon commerce.? CO2e.com is a subsidiary of the Cantor Fitzgerald Group, one of the world?s leading brokerage firms Recent Investor in CO2e ? Mitsui & Co. Alliance with Cantor Fitzgerald Environmental Brokerage Services Group (CFEBS) Offices in London, Toronto, Tokyo, New York, San Francisco, Los Angeles, Connecticut, Houston Primary Goals/Benefits of ET § Goals of Emissions Trading: ? Permit Industrial Growth/Expansion ? Promote Economic Efficiency and Flexibility in Meeting Air Pollution Standards § Benefits of Emissions Trading: ? Enhance Air Quality w/o Economic Stagnation ? Encourage Development of New Technology ? Foster Most Efficient Use of a Limited Resource -- Clean Air § Contributes to Sustainable Development and objectives of UNFCCC, Kyoto Protocol?.

Nov 1, 2002

By Derek Perkins

"Brenda Mines Ltd. operates an open pit copper and molybdenum mine located in south central British Columbia. The main economic mineralization is chalcopyrite and molybdenite. Pyrite, galena and sphalerite are also present in varying quantities. The mineralization is present in small veins and fractures in a porphyritic quartz diorite host rock.The mill processes approximately 30,000 tonnes of ore daily. The ore is crushed in three stages and then ground in conventional rod mill - ball mill circuits with cyclone classification. The cyclone overflow is fed to the bulk flotation circuit as a pulp with a density of 50% solids. The particle size distribution is approximately 35% plus 65 mesh. Bulk rougher and cleaning flotation produce a concentrate grading approximately 20% copper and 4% molybdenum. This concentrate is fed to the separation circuit, where the copper is depressed with sodium hydrosulphide and the molybdenum is floated. These products are further ground and then upgraded by column flotation. The molybdenum concentrate is pumped to the leach plant to reduce concentration of lead and copper. It is then washed, filtered, dried and packed for shipment to Europe. The copper concentrate is filtered, dried and subsequently shipped to Japan.Prior to November 1977, the mill flotation control was carried out by the assay laboratory using a Philips PW 1540 sequential x-ray spectrograph. The assay set consisted of twelve samples, analysed on a two hourly basis for copper, molybdenum, lead, iron and silica.In order to provide elemental composition information on a much shorter sampling interval and to produce speedier control analysis for automating process control, an Applied Research Laboratories PCXQ on stream analyser was purchased. The installation of this analyser, reduced the turnaround time of the control analyses from (2) hours to (20) minutes. At Brenda, the following assays are used in the mill control strategies."

Jan 1, 1989

By Andrew Matyas

"During the summer of 1968, the author was employed in the Research Department of Dominion Foundries and Steel, Limited, Hamilton, Ontario. Over the years, Dofasco has been conducting a program for developing more efficient control of its basic oxygen steelmaking process. The author was thus able to obtain a variety of viewpoints from both research engineers and furnace operators. He also had access to extensive literature dealing with BOF control schemes underway at other major steel producers. This paper describes the present state of developments in BOF steelmaking control.The necessity for efficient BOF control is pointed out. To appreciate the variables to be controlled, a brief outline of process fundamentals is included. Technical aspects of present methods of practical control are examined in detail; the relative merits of dynamic over static control models are emphasized. Finally, it is shown how an effective dymic-optimizing control scheme serves as the basis for closed-loop computer control of the process."

Jan 1, 1970

By Karl J. C. Harries

"12.1. NO DEPRECIATION/GAAPAll calculations and computations relating to the Royalty shall be carried out in accordance with generally accepted accounting principles consistently applied to the extent that such principles are not inconsistent with the provisions of this Schedule and the agreement attached hereto, it being specifically agreed that nothing herein contained shall permit, or be construed to permit, the Operator to deduct any amount for depletion, depreciation, amortization or any deduction that represents a non-cash outlay.Comment: In cases like net profit royalties where recoupment of prior expenditures is permitted, care should be taken to avoid any implication that depreciation may also be taken. It is only logical and equitable that Property Owners should not be permitted an apparent ability to “double dip” with respect to deductions. A provision like this example should accomplish the task. It will be noted that the example specifically contemplates that the negotiated arrangements will prevail over any requirements of GAAP. Accordingly, if the parties agree to an unusual formula for recoupment, it will not be set aside to accommodate GAAP requirements. Under GAAP, revenues and expenditures are accounted for on an accrual basis. In addition, it specifically prohibits the taking of non-cash deductions, which is in keeping with the concept of recoupment.Although in some ways the example states the obvious and could be considered redundant, its presence, especially in provisions contemplating recoupment, makes it clear to the financial people that there may well be some variations from normal practices dictated by GAAP, while at the same time confirming the availability of GAAP to fill any voids.The accounting profession often makes the caveat that application of GAAP is an “art”, not a “science”. GAAP do not provide a cure-all and can create problems that will have to be addressed. For example, GAAP contemplate that asset costs are to be reduced by investment tax credits, which can cause a problem for a payor with more than one mine."

Jan 1, 2003

By V. J. Southey

HOLLINGER mining operations have required development by 24 vertical shafts having a total length of 28,160 feet. Seventeen of these are sunk from surface and seven are interior shafts. Four surface shafts and three interior shafts are now active and, excepting the recently completed new main ore-hoisting shaft, the remainder are either abandoned, or are used for passes or for ventilation. The new shaft bottoms 60 feet below the 3,050 level, but there is much work to be done before it is placed in service. The term 'shaft practice' is intended to include shaft construction and a general treatment o typical equipment. It is a large subject for an organization the size of Hollinger and this paper is intended only to present the salient features. The writer wishes to thank the management for permission to publish this information and to acknowledge the advice and criticism o A. G. Irving, chief engineer, and the willing co-operation of other members of the Hollinger staff.

Jan 1, 1939

By L. C. So, S. Faucher, S. Mostaghel, A. Triwahyuono, D. Sauter, S. -Y. Oh, S. K. Lee, K. Aswin

"Molten hauling and water granulation are the commonly used slag treatment methods in the production of nickel. Water is present in these processes either to accelerate cooling of the dumped slag or in the granulation itself which creates an inherent safety risk of explosions. Even good design and operation are not sufficient to prevent explosions or injuries from occurring. Several dry methods to treat slags have been intensely studied. However, most of these technologies have never been commercialized due to numerous challenges including scalability, cost, low heat recovery efficiencies, and difficulties in heat utilization. Ecomaister-Hatch has recently developed and commercialized a reliable and simple Dry Atomization process, which eliminates water and allows for heat recovery. As part of the development towards other sectors, laboratory-scale and pilot-scale trials have been completed in a number of base metals and PGM facilities. Recently, Dry Atomization of a nickel laterite slag was successfully demonstrated at the laboratory-scale. The current paper introduces the technology and reports the test results obtained from atomization of the nickel slag.INTRODUCTION The processing of nickel laterites produces vast amounts of slag with over 90% of the feed to the furnace reporting as slag. Slag handing is therefore of critical importance to a laterite smelter. Traditionally there are two ways in which the slag is handled (1) Molten hauling, dumping, cooling and quarrying (2) Water granulation, dewatering, stockpiling. There are inherent disadvantages of both methods that will be outlined in this paper. An alternate route of Dry Atomization provides distinct advantages over the two conventional routes that are of particular interest to the nickel producer such as elimination of molten hauling, dumping and quarrying, elimination of water and improved safety. There is also the potential to convert the slag, which is typically regarded as a waste product, into a value added product and the continuous nature of slag tapping makes it amenable to heat recovery. Hatch has recently conducted laboratory-scale test work on laterite slag to demonstrate its viability for Dry Atomization. Results of this work are presented."

Jan 1, 2017

By W. K. A. Congreve

Introduction Less than a hundred years ago the engineer was able to do his job without concern for the science that underlay his practices or for the men who operated his machines. But toward the end of the last century science began to be applied to industry, and its success was such that the plant which clung to empiricism was unable to compete with the plant that followed science. Even more recently, the engineer has been forced to consider the men who operate his machines, for modern large-scale industry has given these men education, social security, and power. Hence the engineer can get good, steady labour to operate his machines only if he can offer inducements. Wages are in general outside the control of the engineer, but he is able to control working conditions. This essay is concerned with one factor of good working conditions: safety. The writer became interested in this problem during three months' summer employment as a student at the Sullivan concentrator of the Consolidated Mining and Smelting Company and was surprised at the distance his investigations led him from the field of pure engineering into the fields of psychology, education, and publicity. Nevertheless, because safety has to do with machines and with men who operate machines, and because it profoundly affects plant efficiency, it is the job of an engineer, not of a psychologist or teacher, nor of the salesman publicity expert who is often so unfortunately employed in personnel relations. The size and complexity of the subject has limited the scope of this essay to the consideration of only a few aspects of industrial safety. Considerable attention has been given to the underlying principles, but the mechanical side of accident prevention, the design of equipment, erection of guards, etc., and the very important problems of organization and administration, have not been given attention proportionate to their importance.

Jan 1, 1948

By S. H. Schulz

100 YEARS AGO, on the first of August, 1877, the mining engineer Friedrich Koepe was granted the patent rights for a hoist driving ropes on the principle of friction. It was named after him: the Koepe hoist. On the occasion of this centenary, the main features of the Kcepe principle are described.

Jan 1, 1977

By P. Tracy

An advanced real-time monitoring system, called a "Tapblock Diagnostic System" is under development to help furnace operators manage the operation and maintenance of their tapblocks. The life of a water-cooled tap block in a smelting furnace ranges from several months to several years, depending on the operating conditions. Tapblocks are typically replaced at regular maintenance intervals; a strategy based largely on historical records and not on the actual condition of a particular tapblock. The Tapblock Diagnostic System monitors the tapblock throughout its life and accumulates probable wear events to help the operator assess the residual integrity of the tapblock. Benefits of this system include the ability to provide early warnings of tap block wear to provide improved safety and maintenance planning. Using cooling-water flow together with copper and water temperature measurements, the system performs calculations that compare the present tapblock performance with the expected operating envelope using a multivariate statistical method (Principle Component Analysis). The operating envelope is pre-calculated for a wide range of operating conditions using transient thermal modeling (Computational Fluid Dynamics). A state indicator in the form of a green, yellow and red light is used to inform operators of the tapblock performance and health status.

Jan 1, 2007

By D. J. Charlton

"IntroductionMaintenance is a business, which to be successful, requires good management, systems and reporting. The prime objective of the maintenance management group, be they large or small, must be to anticipate and prevent interruptions in operations by keeping equipment in good mechanical condition. This objective should be carried out at minimum cost consistent with maximum productiveness.The objective of this chapter is to give an insight into the various aspects of maintenance management that must be considered to effectively and efficiently operate a mill complex. The degree to which the maintenance sub-systems are developed in an operating mill will be determined by the size of the mill and the needs of the operation.The criterion of the management system used is that the system serve the operation and not vice versa. The systems presented should be considered as tools and, as with all tools, they must be sharpened and replaced as the need arises or as more effective tools become available.To understand what is involved in maintenance management, it is worthwhile to consider a systems approach to analyzing management problems. This approach was developed by J.A.B. Rae while reviewing maintenance management systems for Cominco Ltd.A very simple system involving managing results and objectives is shown diagrammatically in Figure 1.The systems approach to organizational development involves four basic elements: an objective, a result, an activity and feedback. In the analysis, the activity element is broken down into individual actions that people could be held responsible for. If we introduce the action of operating into the diagram of Figure l, we arrive diagrammatically in Figure 2."

Jan 1, 1989

By C. H. Hopper

DIAMOND drills have played an important part in the development of mines for many years. Recently. they have also entered the production field arid the use of diamond drills m the primary breaking of ores has become a big branch of the industry. The writer has estimated roughly that the total diamond drilling in Canada during 1942 was 5,625,000 feet, of which 2,250,000 feet, or 40 per cent, was for blast-holes. This accounts for 6,750,000 tons of ore broken, using the conservative factor of 3 tons per foot of hole. Many consider that the use of diamond drills for blast-holes is the most important advance in mine practice of the past decade, and the industry owes a great deal to the staff of Noranda Mines, Limited, for the pioneering they have done in the development of long-hole mining methods and for publishing their results. A great many mines have followed Noranda's lead. At the Waite-Amulet, Aldermac, Flin Flon, Canadian Malartic, Hoyle, and Matachewan Consolidated mines, most of the ore is broken by long-hole blasting. While the mines were developing new methods, the diamond-drill industry was developing mechanically-set bits and better machines. Through the effective use o smaller, cheaper diamonds, as well as more efficient setting, bit costs per foot are only one-half what they were ten years ago. Few people realize that a diamond bit is relatively inexpensive. The common EXT coring bit, for example, contains some 200 small diamonds, weighing altogether about 2.70 carats which, at $3.40 per carat, cost $9.20. After use, the equivalent of about 100 of these diamonds may be recovered. Therefore the true cost of the bit is only $7.00, made up of $4.60, the cost of the diamonds lost, $2.00 for setting, and $0.40 tax. The trend in machines has been toward specialization for the different classes of rock in blast-hole work. Light, high-speed machines have been developed for soft ores and higher powered machines for hard ores.

Jan 1, 1943

By R. G. Eggert

"A critical element, as the term has come to be used, provides essential properties to a modern engineered material and is subject to supply risk. The rare-earth elements became perhaps the most prominent of the critical elements in recent years because of their important uses in permanent magnets, advanced lighting, and military materials; the geographic concentration of production in China; and the dramatic run-up in prices in 2010-2011 followed by price collapse between 2011 and 2016. Yet criticality extends beyond the rare earths. What is critical depends on your perspective – who and where you are, and when you ask. This paper reviews the many perspectives on, or faces of, critical elements. It compares and contrasts perspectives of industry (General Electric), national or regional manufacturing sectors (Japan, European Union), emerging energy technologies (as seen by U.S. Department of Energy and, separately, Joint Research Centre of the European Commission) and the world as a whole (as evaluated by academics). This comparison reveals a diversity of not only perspectives but also methodologies and time frames of concern.INTRODUCTIONRare-earth elements appeared prominently in the news in 2010 and 2011 because of the dramatic increase in their prices; their important uses in permanent magnets, advanced lighting, and military materials combined with the geographic concentration of production in China, which reduced export quotas significantly. Rare earths became the most prominent of what have become known as critical elements or materials – that is, those that provide essential properties to modern engineered materials and yet are subject to supply risks.Yet criticality, the state of being both essential and subject to supply risks, extends beyond rare earths. What is critical depends on your perspective. This paper begins by reviewing a little history and presenting a general conceptual framework from which to think about critical materials. It then reviews the many perspectives on, or faces of, critical elements – corporate, national, and global, as well several that focus on emerging energy technologies. The paper concludes with thoughts on what to do to mitigate the potentially negative effects of the supply risks associated with criticality."

Jan 1, 2016

"The asbestos mining industry in the Eastern Townships of Quebec has early recognized the undesirable side-effects associated with mineral production, such as air pollution, noise and unsightly waste dumps. In order to efficiently achieve the industry's aim of eliminating or minimizing these objectionable features of mining, all of the asbestos producers in Quebec interchange information, knowledge and design dealing with the environmental control measures through the Environmental Committee of the Quebec Asbestos Mining Association.The paper describes what has been done and what is planned for the future in the various problem areas, such as control of dust emitted during the open-pit drilling operation, control of dryer stack emissions, control of the environment in ore, fibre and tailings handling operations, rehabilitation of the countryside covered by waste dumps, and many others."

Jan 1, 1971

By A. I. A. Salama, M. W. Mikhail

"A comprehensive software package has been developed at the Western Research Centre to meet many of the coal preparation requirements in the Canadian coal industry. This package performs three main functions: (1) data handling and manipulation; (2) data analysis, including the generation of washability data, performance evaluation and prediction, density and size modelling, evaluation of density and size partition characteristics, and attrition curves; and (3) graphics output.The software described in this paper is potentially a valuable tool for coal preparation plant engineers and operators for evaluating process performance and adjusting plant density separator cutpoints. Moreover, the analytical laboratory technician could find this package very useful in manipulating and presenting laboratory results."

Jan 1, 1997

By B. Benmokrane, G. Ballivy

"RésuméLe mécanisme de transfert des charges et le processus de décohésion le long des scellements d'ancrages scelles dans des massifs rocheux sous des charges de tensionnement peut être examine par instrumentation de l'ancrage à l'aide de jauges de déformation. Dans ce contexte il est présente ici les résultats d'une étude, en vraie grandeur sur chantier, ayant porte, d'une part sur des essais d'arrachement conventionnels et d'autre part sur des essais déflagrée barres d'ancrages instrumentées et scellées à l'aide d'un coulis de ciment dans un massif rocheux sain et compètent. Les résultats décrits ici, particulièrement les profits de contraintes de cisaillement le long de l'ancrage, obtenus à partir des valeurs de déformations relevées sur les jauges, ont permis de préciser le niveau de chargement correspondant à la décohésion initiale du coulis de scellement, d 'examiner l'effet de la décohésion sur la distribution des contraintes et de caractériser le fluage du système barre d'ancrage/coulis de scellement.ABSTRACTThe load transfer mechanism and the debonding process along grouted rock anchor, subjected to tention loads, can be examined through the instrumentation of the anchor with the aid of strain gauges. In this context, the resultsof a full-scale site investigation including classical pull out tests and creep tests are presented in this paper. These tests were performed on instrumented bars which were cement grouted in a competent rock mass. Results presented in this paper concern, among others, shear stress pro/ties along the grouted anchors which were determined from strain values obtained from the strain gauges. These results have been used to: (1) predict the load level corresponding to initial debonding of the grout; (2) study the effect of debonding on shearstress distribution along the anchor; and (3) characterize the creep behavior of the bar anchor/cement grout system."

Jan 1, 1991