Search Documents

By D. B. Haas

THE HYDRAULIC TRANSPORT of solids is becoming increasingly prevalent throughout the world. Major long-distance slurry pipelines currently in operation transport commodities such as coal and various ore concentrates distances of up to hundreds of miles. In the United States, a number of large-diameter, high-tonnage pipelines are under consideration for the transport of Western Plains coal to markets up to 1000 miles away. In these and other applications, the solids are generally quite fine, with 14 mesh being a typical limit of particle size for long-distance (over 100 miles) slurry transport. There are applications where it might be practical to transport solids consisting of larger particles distances of up t o 100 miles. Deposits of high-quality metallurgical coal are found in the inner foothills belt along the eastern edge of the Rocky Mountains on the Alberta-B. C. border. There are few existing railroad s and the possibilities of constructing extensions are limited because of environmental and economic factor s. In these circumstances, the most efficient transportation system might consist of a pipeline to transport the coal from the mine to beneficiation plants located near existing railroads 50 or 100 miles away. Such systems would minimize environmental effects, capital cost s and operating costs. To determine whether such a system would be technically feasible, experimental testing is needed to determine the energy requirements for transporting coarse coal in a pipe line. Currently, run-of-mine metallurgical coal is crushed to less than 1 1/2 inches before going to the beneficiation plant. In the proposed scheme, coal of this size would be transported through a pipeline to the beneficiation plant located at the railroad. The Transportation Development Agency and the Department of Supply and Services have awarded a contract to the Saskatchewan Research Council to study pipelining of coarse coal in pipelines ranging from 4 inches to 12 inches in diameter.

Jan 1, 1977

By L. Sun

In this work, strontium doped lanthanum ferrite (LSF) and their composite cathodes were fabricated by screen printing on yttria-stabilized zirconia (YSZ) electrolytes. Their electrochemical properties were evaluated by using electrochemical impedance spectroscopy and steady-state polarization methods. All the cathodes were screened by comparing their total polarization resistances before and after activation processes at different temperatures. The improved LSF composite cathodes were also screen-printed on YSZ/NiO half cells to fabricate solid oxide fuel cells (SOFCs), which have reached the output power densities of 170 mW/cm2 at 650 °C, 230 mW/cm2 at 700 °C, 304 mW/cm2 at 750 °C and 388 mW/cm2 at 800 °C.

Jan 1, 2005

By R. L. Bruening, R. M. Izatt, N. E. Izatt, S. R. Izatt

"Molecular Recognition Technology (MRT) is a simplified, green chemistry process with applications in selective separations of Ni(II), Co(II), and platinum group metals in primary ore beneficiation processes and secondary recovery operations from spent products, scrap, and environmental waste solutions. Simplification in MRT processes is achieved by non-use of solvents, reduced space requirements, and a simple separation system involving columns packed with metal-selective SuperLig® resins. Minimal waste is generated and metal recovery is achieved at 99% levels from g L-1 to <mg L-1 concentrations. MRT systems are attractive technologically and economically compared with solvent extraction, ion exchange, and precipitation separation processes. Commercial examples of MRT use include removal of impurity metals Cd, Cu, Ni. Fe, and Pb to mg L-1 or lower concentration levels from Co streams to produce battery-grade Co. Highly purified Co is required for optimal function of lithium ion rechargeable batteries and superalloys associated with aerospace and gas turbine operations. Impurity metals are recovered for reuse or proper disposal rather than being discarded to landfill. Green chemistry processes, such as MRT, are needed in metal separations going forward into the 21st century to achieve global metal sustainability in processing of native ore and treatment of secondary sources.INTRODUCTION Maximizing efficiencies of metal separations and optimizing metal recovery rates during separation processes are important goals on the road to achieving metal sustainability. Achievement of these goals is consistent with stated principles of green engineering (O'Connor, Zimmerman, Anastas, & Plata, 2016) and green chemistry (Anastas & Eghbali, 2010). Molecular Recognition Technology (MRT) separation processes using SuperLig® resins have a 25-year record of performing competitive, commercial metal separations with metal recovery rates approaching 100% (Izatt, Izatt, Izatt, Krakowiak, & Bruening, 2017). SuperLig® resins are characterized by high selectivities for specific metals over concentration ranges from g L-1 to mg L-1 or lower. MRT systems use no solvents and are simple in design and operation resulting in reduced capital and operating expenses."

Jan 1, 2017

By S. Uddin

Microsegregation manifests its effect on microstructural evolution of cast or welded alloys which in turn influences their important mechanical and electro-chemical properties. In the above context, mathematical models of microsegregation have proven to play an important role in estimating the nature and predicting the effects of this phenomenon in wide varieties of solidification processes. Microsegregation models are useful in designing new commercial alloys, in estimating the homogenization time for the post-process heat treatments and in many other practical applications. In this study, two semi-analytical models of microsegregation were developed to predict the concentration field of solute in the liquid and solid regions for dendritic solidification of binary metallic alloys. Both models assume that the growing dendrites are cylindrical in shape. This assumption is more realistic compared to the common assumptions of plate like dendrites that most of the earlier researchers employed in their microsegregation modeling study. The solute redistribution profile, in the developing solid layer, necessary to determine the back diffusion parameter was derived from Fick&apos;s second law for the model without coarsening. The application of this parameter in a wide range of conditions and the use of its basic form in the model with coarsening has been verified. The concept of coordinate transformation and enhancement of back-diffusion Fourier number were used in deriving the model which took into account the coarsening of dendrites. The models are then extended to deal with rapid solidification and peritectic transformations and the results were compared with relevant experimental data for Aluminum and other alloys. A good agreement between model predictions and experimental results was found.

Jan 1, 2007

By J. Currie, J. McManus, R. Chenier

"Cominco Copper Division&apos;s Valley Mine is located in the Highland Valley of British Columbia, approximately 275 km by air northeast of Vancouver. The nearest towns are Logan Lake, located IS km to the east and Ashcroft, located about 50 km to the northwest.Preproduction stripping of rock and overburden at the Valley Mine&apos;s Lake Zone Pit began in mid-1982 following a decision to discontinue mining in the adjacent Jersey Pit. Equipment and mining methods were carried over from the Bethlehem Copper operations which, with Valley Copper Mines, were merged into Cominco in December 1982.Blasting practices, as carried over from the Bethlehem pits, were designed to provide the fine fragmentation required to meet production requirements using the Bethlehem crusher. However, after mining the first few benches of the Lake Zone Pit, it became apparent that overblasting at the pit limits was causing a number of bench failures, as well as contributing to an over-all reduction of the material strength of the rock mass forming the southwest wall of the pit.With present ultimate pit plans calling for the southwest wall to be as high as 300 m, Valley staff realized that potential slope stability problems should be dealt with as early as possible. This philosophy would enable experimentation on phase pit walls in order to attain the optimum slope angle on the ultimate pit wall.As part of an over-a ll slope stability program, a controlled blasting program was initiated at the Lake Zone Pit in March 1983. In this program, Valley engineering and production staff worked together with Golder Associates in establishing design criteria and evaluating the results. This program resulted in a marked improvement in the soundness of pit walls while maintaining the required degree of fragmentation."

Jan 1, 1985

By Wendy L. Naysmith

This paper deals with the various options considered and factors that influenced the final selection of the headframe, shaft layout and hoisting systems required at the Impala No 16 Shaft in order to hoist both the required 3 Mt of ore per annum, and transport men, material and equipment between the surface and the underground workings to a depth of 1640 m. The layout and construction method used for what is at present the world?s tallest concrete headframe is discussed together with the integrated hoist room foundations designed to suit multiple mechanical and electrical hoist supplier?s solutions. The mechanical components of the two tower mounted 6,5m 4 rope Koepe hoists and deflection sheaves and their layout is dealt with in detail. Various features of the bearing type, brake units and brake control system are also discussed. Installation of the mechanical and electrical hoist equipment in the headframe took place during the sinking phase of the project and placed severe restrictions on the use of the heavy lifting facilities. This required a well-managed and systematic approach to delivery of the hoist components and associated equipment, as well as close co-operation between all contractors on site.

Oct 1, 2010

By Charles Graham

For hundreds of years the standard vertical mine shaft was rectangular shaped and timber lined. There are many advantages to rectangular shafts but as mines became deeper the circular shaft became more popular. The chief advantages of circular, concrete lined shafts are their ability to resist lateral pressure and they offer less resistance to ventilation air. A number of elliptical shafts have been sunk in an attempt to realize the advantages of both the rectangular and the circular shaft. A concrete lined elliptical shaft provides better space utilization than a circular shaft, would allow for shaft sinking with two double drum hoists, as well as concurrent level development. The design also makes one sided stations possible and provides for a simple headframe design.

Feb 1, 2008

By R. Stratton-Crawley, S. W. Wilson

"Inco's Matte Separation Plant is a unique mineral processing facility having no process tailings stream. Each product is a high-grade concentrate with strict assay specifications which are defined by the downstream refining route. The most recent column application in the flowsheet, copper scavenging in the production of a high quality nickel concentrate, is described in detail. Testwork in pilot-scale columns (0.038 m, 0.051 m and 0.10 m in diameter) was used to develop a model of the copper scavenging system. This data was then used to simulate the performance of plant-scale equipment. The relationships thus established were confirmed by a series of plant tests in a 1.8 m diameter column. Column results consistently exceeded conventional cell performance. The modelling was extended to assess full plant production requirements and, as a result, a 2.1 m diameter column was specified for this application. Engineering design for this column is currently underway and the column is scheduled to be commissioned later in 1991.INTRODUCTIONMatte SeparationINCO's Matte Separation Plant is a part of the Copper Cliff Smelter complex near Sudbury Ontario. The flowsheet and the development of column flotation within it have been described previously (Feeley et al., 1987, Wilson et al., 1989). The plant feed is a synthetic Bessemer Matte from the Nickel smelter. This matte is slow cooled to promote grain growth and typically assays 46-52% Ni, 23-27% Cu. These elements are present primarily in sulphide form (Ni3S2 and Cu2S respectively) with some metallic alloy also precipitating from the sulphur deficient matte. Minor amounts of iron, precious metals, and nuisance elements are also present.The matte separation process is, in concept, relatively simple. Following magnetic removal of the metallic alloy from the feed, the flowsheet is designed to float a high grade copper concentrate from the nickel sulphide matrix. A simplified flowsheet of the process is shown in figure 1."

Jan 1, 1991

By E. M. Shemang, C. E. Suh, L. Mbinkar, University of Yaounde

"Two iron deposits within the Precambrian mineral belt of Cameroon are described in detail for the first time: the Archean Metzimevin replacement iron deposit enclosed in Fe-enriched itabirite, and the Proterozoic granite-hosted, shear zone-related Mayo Binka magnetite deposit. In the Metzimevin de¬posit, quartz is corroded and microplaty hematite overprints martite-textured hematite. The Mayo Binka massive magnetite veins show evidence of deformation in magnetite (fracturing and microbrecciation) and in overgrowths of specular hematite (mechanical twinning and undulating extinction). The magnetite is partially replaced by hematite (martitization) and goethite. Ores from both deposits have >88% total Fe2O3 and low contents of contaminants such as SiO2, Al2O3, MgO, CaO, P2O5, and TiO2. They are also poor in Cu, Pb, Zn, V, Cr, and Ni. The Metzimevin massive hematite is characterized by an accentuated light rare earth element depletion relative to the Fe-enriched itabirite. It is suggested that the Metzimevin iron deposit is the result of hypogene leaching of gangue minerals from, and further hematitization of, an itabirite protore. Although the genesis of the Mayo Binka massive magnetite is unclear, it is spatially related to Neoproterozoic granitic rocks. The data allow some comparison of these little known, but pot¬entially economic iron deposits, with some of the world’s better investigated deposits, and are useful to the exploration efforts for iron ore currently underway in Cameroon and the Central African subregion.Deux gisements de fer de la ceinture minérale Précambrienne du Cameroun sont ici décrits en détail pour la première fois : le gisement de fer Archéen de Metzimevin formé par remplacement et encaissé par des itabirites enrichies en Fe, et le gisement de magnétite Protérozoïque de Mayo Binka as¬socié au cisaillement dans un granite. Au gisement de Metzimevin, le quartz est corrodé et de l’hématite en microplaquettes se développe au dépends de l’hématite a texture martitique. Les veines de magné¬tite massive de Mayo Binka présentent des évidences de déformation dans la magnétite (fracturation et microbréchification) et dans les surcroissances d’hématite spéculaire (Macles tectoniques et extinction ondulante). La magnétite est partiellement remplacée par l’hématite (martitisation) et par la goethite. Le minerai des deux gisements contient >88% de Fe2O3 total et un faible contenu en contaminants tels que SiO2, Al2O3, MgO, CaO, P2O5, et TiO2. Il est également pauvre en Cu, en Pb, en Zn, en V, en Cr et en Ni. L’hématite massive de Metzimevin est caractérisée par un appauvrissement relatif en terres rares légères relativement à l’itabirite enrichie en Fe. Il est suggéré que le gisement de fer de Metzimevin résulte du les¬sivage hypogène des minéraux de la gangue ainsi que de l’hématitisation poussée d’une préconcentration de fer dans l’itabirite. Bien que la genèse de la magnétite massive de Mayo Binka demeure obscure, elle est spatialement associée aux roches granitiques Néoprotérozoiques. Ces données permettent de comparer ces gisements de fer peu connus et potentiellement économiques avec certains des gisements mondiale¬ment mieux connus, aidant ainsi les efforts d’exploration présentement en cours en Afrique de l’ouest et au Cameroun."

Jan 1, 2008

By J. P. Mogan, E. D. Dainty, A. Lawson

"The toxicity reduction of emissions from two diesel engines by the emulsification of water into fuel oil was investigated to determine the applicability of such systems to underground mining machinery. . The engines studied were: 1) the Deut; F6L7J4, four-stroke, air-cooled, 6-cylinder, V-configuration, indirect-injection (IDl) engine, and 2) the Detroit Deisel Allison Division 8V7JN, two-stroke, water-cooled, 8-cylinder, V-configuration, direct-injection (Dl) engine.The application of emulsified fuel treatment to the two-stroke engine did not prove to be practicable. In the case of the Deutz engine, however, substantial benefit resulted. For a modest J5 per cent water content in the fuel and an injection timing of24° BTDC, approximate reductions of40 per cent in the concentrations of both particulate matter and nitric oxide (NO) were produced. These reductions were accompanied by insignificant changes in other toxic constituents. The net result was an approximate 30 per cent reduction in the over-all exhaust toxicity for typical LHD operation as assessed by the Health Effects Index criterion. This toxicity reduction represents a significant advance from the points of view of an improved underground environment and/or reduced ventilation costs."

Jan 1, 1981

By G. P. Holmes

"IntroductionThe copper-molybdenum property of Brenda Mines Ltd. is located 18 miles north west of Peachland in the Okanagan Valley of the Southern Central interior of British Columbia. The actual site is 50 miles north of the international boundary and 150 air miles east of Vancouver at an elevation of 5000 feet above sea level. The earliest written mention of the prospect is found in the Geological Survey of Canada, Memoir No. 243, issued in 1947 by Dr. H.M.A. Rice. In 1954 the area was staked by a prospector, Bob Bechtel, who interested Bern Brynelsen of Noranda Exploration in examining the claims. A joint Noranda - Kennecott program resulted but since the grades were so low the property was not taken up until in 1964 a re-examination by Chapman, Wood and Griswold produced recommendations leading to the construction of the Brenda Mine as it is today.The rounded, timber covered mountains of the area are composed of the tuffs, argillites and limestones of the Upper Triassic Nicola Group, which is intruded by a Jurassic quartz diorite, called the Brenda stock0 The actual orebody occurs in a strongly fractured zone within the Brenda stock, approximately 1500 feet from the contact with the Nicola group0 The ore minerals, .chalcopyrite and molybdenite, associated with pyrite and magnetite of lesser importance, occur as fillings within the fractures 0 The grade of the ore decreases outwards from a central higher grade core and in January 1971 total reserves were estimated at 165 million tons assaying 0,182% Copper and 0,049% Mo."

Jan 1, 1972

By Diankun Lu, Ganfeng Tu, Edouard Asselin, Feng Xie

A novel separation process for detoxifying cadmium-containing residues arising from zinc hydrometallurgical processes has been developed. An initial investigation indicated that a high concentration of zinc in the sulfate solution can be effectively separated from cadmium by solvent extraction with P204 (di(2-ethylhexly)phosphoric acid, D2EHPA). The mixture of sulfuric acid and ammonium citrate ((NH4)3C6H5O7) is thus used to extract metals from the residue at room temperature. Copper in the leachate is recovered by solvent extraction (SX) with LIX 973. Cobalt in the raffinate from the copper SX process is recovered by precipitation with a-nitroso-ß-naphthol. The results show that more than 50% of the copper and virtually all the zinc, cadmium and cobalt in the residue can be leached under the experimental conditions used here. Virtually all dissolved copper and cobalt can be recovered in the subsequent solvent extraction and precipitation processes. The presence of (NH4)3C6H5O7 could significantly facilitate the extraction of zinc by D2EHPA in the subsequent separation of zinc and cadmium. More than 97% of the dissolved zinc can be recovered through a two-stage counter current solvent extraction process. After separating copper, cobalt and zinc, cadmium can easily be recovered from the solution either by cementation with zinc powder or by electrowinning, while the purified solution can be recycled back to the leaching process.

Jan 1, 2014

By Mani Manimaran, Inna Dymov, Mariam Melashvili, Chris Fleming, Joe O’Day

This paper presents experimental evidence that supports the use of bromine/bromide as a potential alternative to conventional cyanidation for gold leaching. The study evaluated a brominebased lixiviant, Stabilized Bromine, with considerably lower vapour pressure than liquid bromine. Using a rotating device, the rate of gold dissolution was determined at various concentrations of this reagent. The reactivity of pure pyrite, arsenopyrite and chalcopyrite minerals was also evaluated in stabilized bromine reagent. Furthermore, bromine leaching of gold in a number of gold bearing ores was undertaken. Results showed that significantly higher gold recovery can be achieved with bromine than with cyanide when leaching gold encapsulated in sulphides, but bromine consumption was high owing to simultaneous oxidation of the sulphides. The greatest promise for the bromine leach process was with oxidized gold ores. The recovery of gold from oxide ores with bromine was comparable to that achievable with cyanide and bromine consumption was reasonable when leaching was conducted at a near neutral pH of ~6. In the case of oxidized gold ores containing copper mineralization, it is possible that bromine consumption may be lower than cyanide consumption, since there is evidence to suggest that bromine is less reactive than cyanide with copper minerals.

Jan 1, 2014

By H. J. White

Haynes International, a world leader in the manufacture and production of nickel, and cobalt base alloys has invented and developed a low cost high temperature material, with a unique combination of superior oxidation resistance and weldability/ fabricability. HAYNES® HR-224TM (Ni ? 27.5Fe ? 20Cr ?3.8A1 ? 0.3Si ? 0.3Ti) forms a planar/ continuous/ adherent aluminum oxide film at high temperatures which has been shown to effectively limit chromium poisoning in solid oxide fuel, cell, systems. A 20,000 pound vacuum induction melted (VIM) + electroslag remelted (ESR) heat has been melted and converted into various product forms: sheet, plate, bar, welded tubing, wire, etc. The alloy was designed for service in severely oxidizing environments recuperators, automotive catalytic converters, wire strand annealing furnace tubes, etc. and has been of great interest to solid oxide fuel, cell, manufacturers as a materials of construction in balance of plant (BOP) design. This manuscript presents the physical, properties, mechanica, properties, and oxidation resistance of the alloy compared to other materials being considered for solid oxide fuel, cell, design

Jan 1, 2010

By John Hoffert, Darren Colwell, Greg Tucker, Jeremy Kinch, Greg Rasmussen

"The Kemess Mine, a major producer of gold and copper, is located in north-central British Columbia. Kemess was brought into production in May 1998 by Royal Oak Mines. On February 11, 2000 Northgate Exploration Limited acquired Kemess Mine from receivership. Since acquisition in 2000 Kemess has seen many accomplishments, including the reduction of costs by 40%.One of the largest site capital costs was the construction of the tailings storage facility dam, which when finished will be one of the largest earth filled dam structures of its type. The existing construction design by AMEC called for a kilometer wide rock dam to be built from the 1350 M elevation to the 1504 M elevation at a 5.5:1 slope by hauling over 30 million tonnes of non-acid generating waste rock 7-kilometers from the open pit to the tailings dam, which was highly expensive.Kemess realized an opportunity for cost reduction was possible if the dam could be built from suitable quality tailings sand; however the sand did not meet the neutralizing potential ratio specifications. It was determined that cycloning combined with flotation to reduce pyrite concentration in the sand would produce a non-acid generating product for dam construction. The sand plant design challenges were to remove the sulphides from the tailings to obtain an NPR greater than 2:1 and provide a consistent sand product for the construction with a fines content of less than 15% passing 200 mesh. After a 2-year testing design and construction period, the sand plant was successfully started at the end 2002 resulting in higher than expected sand quality and production rates.This paper describes the plant design phase, commissioning, and operation of the tailings sand plant for construction of the tailing storage facility dam to enable us to meet all the engineering and regulatory requirements. The many challenges faced were successfully met using several innovative designs. The operational, economic, and environmental benefits are detailed."

Jan 1, 2004

By Jack Zhang, Yunguo Tang, Baodong Zhao

"Rare earth elements (REEs) have numerous key applications in both traditional and advanced technologies. A shortage of some critical REEs is expected due to the discrepancy between the REE abundance in REE deposits and the REE demand from the market. For example, Neodymium, Europium, Terbium, Dysprosium, Erbium and Yttrium are expected to be in short supply. REE recovery and separation from secondary resources such as uranium wastes, heavy mineral sands, and recycled materials can balance the shortfall in a cost effective way.The Saskatchewan Research Council (SRC) is engaged in the development and commercialization of complete REE recovery and separation technologies in Canada. One of SRC’s newest developments is the design and commissioning of a heavy rare earth (HREE) separation pilot plant. The pilot plant uses hundreds of stages of solvent extraction (SX) to produce high purity individual HREEs from both primary and secondary resources.This paper presents the design of an HREE recovery process for the particular case of uranium processing wastes. The separation results of a group separation are reported and discussed, as well as the issues and the challenges of the development, commissioning and operation of the continuous SX pilot plant.IntroductionSignificant amounts of strategic specialty heavy rare earth elements (HREEs) are found in uranium wastes in Saskatchewan. It estimated that about 47 tonne/a of heavy rare earth element oxides (HREO) including 27 tonne/a of Y2O3, plus 6 tonne/a of Sc2O3 are in the raffinate of every uranium mill for potential recovery. Since the HREEs are already in the raffinate, cost effective HREE production is promising in Saskatchewan.Selective precipitation including nutraulization, oxalate and double-salts precipitation, as well as sulfide precipitation, ion exchange (IX) and SX are commonly used technologies for the recovery and purification of REE solution. REE oxalate precipitation is an effective technology to remove Fe, Al, Ca, Si and other impurities by taking the advantages of the solubility difference between oxalates of REEs and impurities in acidic solution (Xu, 2005)."

Jan 1, 2017

By V. G. Papangelakis, M. Cheung, M. Dry

The high pressure acid leaching of laterite was modelled and simulated using a combination of two commercially available software packages, namely Aspen Plus 11.1 and the OLI Stream Analyzer. New kinetic parameters for the acid-controlled metal dissolution and precipitation reactions at temperature were first determined from previous experimental data on the leaching of limonite. A grain model with cylindrical pellets was used to model the solid-liquid dissolution reactions. Precipitation reactions were modeled via aqueous equilibrium chemistry. A dedicated thermodynamic database previously developed at the University of Toronto was used in conjunction with the OLI software to model the solution chemistry and calculate the concentration of hydrogen ions in solution at the leaching temperature. Mass balances were handled by Aspen Plus. The simulation gave good predictions of nickel dissolution under industrial and laboratory conditions, for the dissolution of limonite and limonite/saprolite blends. Computational

Jan 1, 2005

By C. Patel, George H. Hope

"INTRODUCTIONThe Hemlo area is located in Northern Ontario, some 350 km east of Thunder Bay along highway 17. Hemlo is Canada's largest, recent discovery of gold ore. Three companies, Lac, Noranda, and Teck are currently developing mines and processing facilities in the area. A combined milling capacity of approximately 10,000 tonnes per day will ultimately be available in the area. The gold yield will be between 750,000 to 1,000,000 ozs. per year. This will slightly more than double Ontario's gold production but only represents 2.5% of the total world gold production.Lac Minerals Ltd. is substantially committed to the gold mining business. Lac currently operates four (4) gold mines and mills and produces 300,000 ozs. per year. Lac's Hemlo development will put the company in the position of number one gold producer in Canada.The Lac Hemlo ore body has an estimated reserve of 37 million tonnes at 6.2 g/t. The mining will take place at an initial rate of 3,000 t/d commencing in the first quarter of 1986. The mine and plant will be expanded to 6,000 t/d in 1988. At this capacity, Lac will be the largest producer in the Hemlo area.1. GEOLOGYThe orebody is divided into two (2) zones for mining purposes. The 'A' Zone is to the east and dips to the Northeast from surface to 300 m below surface. This zone has a strike length of 250 m to 300 m at an average width of 20 m. The upperpart of the zone will be mined by open pit and the remainder from underground. The 'B' Zone, to the north west of the 'A' Zone, although lined up is not necessarily an extension of 'A' Zone. 'B' Zone has a known strike length of 600 m and is open to depth and along the strike. It is over 70 m wide in the core. This zone holds most of the property's known reserves. 'C' Zone with narrow gold zones is under exploration in the south west portion of the property."

Jan 1, 1985

By Joseph Licavoli, Paul Sanders, Yang Yang

"Al-Sc-Zr alloys form thermally stable L12 precipitates which provide high temperature strength. Although the overall fraction of L12 Al3Sc and Al3Zr may be increased by increasing scandium (Sc) and zirconium (Zr) content, such additions may increase primary phase fractions and do not produce desirable secondary phase morphologies. Rapid solidification techniques, such as melt spinning, increase solute atom concentration within the matrix. When the supersaturated matrix is aged, higher precipitate volume fractions at low Sc and Zr levels can be achieved improving high temperature strength. Melt spinning was used to rapidly solidify (107 k/s) a thin ribbon of Al-0.5Sc-0.4Zr at. %. The ribbon was compacted and extruded into 99.8% dense rods, and then aged using multi-step isochronal heat treatment up to 600°C. Precipitation strengthening was evaluated by ambient hardness measurement. The ambient hardness of melt-spun ribbon after precipitation hardening increased by 450 MPa (~67% increment) during isochronal heat treatment.INTRODUCTION Small Sc and Zr additions to aluminum improve strength and creep resistance above 300°C due to tri-aluminide precipitation of Al3(Sc,Zr) in L12 structures similar to ??, Ni3(Al,Ti) in nickel superalloy, but the Al3(Sc,Zr) particles have a Sc-rich core surrounded by Zr-rich shell (Figure 1). The Al3Zr shell limits atomic transport between the Al3Sc core and the matrix and reduces coherency strain. These factors reduce precipitate coarsening rate at elevated temperature (Bergner & Van Chi, 1977; Fujikawa, 1997; Knipling et al., 2011; Clouet et al., 2006).Figure 1. Simplified schematic model of precipitate Al(Sc,Zr) in Al-Sc-Zr alloy. Shell is rich of Al(Zr) intermetallic phase, particle core is rich of Al(Sc) intermetallic phase (after Voorhees, 2006). Numerous Al3(Sc,Zr) particles increase alloy strength and creep resistance as the precipitates impede dislocation glide and to a lesser extent climb. Previous work on ternary Al-Sc-Zr alloys show large strength increases versus binary Al-Sc, and Al-Zr alloys in Table 1."

Jan 1, 2018

By Robert R. MacLachlan

New underground mining technology is evolving through the use of large-diameter bore holes containing individually restricted charge weights. This article presents summary observations on cube-root scaling trials using single and rows of charge blasting in sand and in frozen ground. These observations have some bearing on the evolving underground practice, especially where charges of appropriate geometry are used.

Jan 1, 1978