Search Documents

By Terry Keough

Contents for discussion ?Current liner technology ?Innovation of magnetic products ?Development of magnetic wear liners ?Installation and change out method ?Uses and capabilities ?Internal wear liners ?Summary Vulcanized rubber ?Many of you are familiar with using vulcanized rubber to provide wear protection on mining equipment. For years, this was the standard for most mining equipment, and mines spent a lot of money fabricating and lining steel equipment.

May 1, 2010

By Oy Leuangthong

The McMurray formation in the Athabasca oil sands deposits of Northern Alberta is part of the world?s second largest proven crude oil reserves. The formation is characterized by stratigraphic layers that correspond to three different depositional environments: Marine, Estuarine and Fluvial facies. Resource estimation for oil sands has traditionally relied on polygonal and inverse distance schemes. These techniques are simple and straightforward in practice, but they do not permit reliable uncertainty assessment. This paper describes the modeling of the McMurray formation using modern geostatistical techniques. Geostatistical modeling should be performed within homogeneous geological facies. The methodology for geostatistical simulation within each of the identified facies involves: (1) assessing the most appropriate stratigraphic transformation for optimisation of the correlation structure, (2) determining representative distributions with declustering and debiasing techniques, (3) modeling spatial continuity of the bitumen grade, fines grade, water saturation and other petrophysical variables, (4) performing estimation and cross validation as checks against simulation results, (5) performing simulation for uncertainty quantification of bitumen and fines grade, and (6) model checking of simulation results against the input data and comparisons against the kriged models. These steps are described in detail. The application of these models for uncertainty quantification in support of resource classification is also discussed.

May 1, 2004

By J. Ellis Thomson

For many years the value of qualitative microscopic investigation has been recognized in both of the fields of pure and applied science. In particular, its aid has been invoked in the determination of rock specimens in thin section, and some at least of the interrelations of minerals present in any one section have been observed and, to a limited extent, applied for the solution of different problems. During the past decade this form of research has also been diverted to the determination of ore minerals in polished section, with some observation of their structural relations. Microscopic research of a quantitative character, on the other hand, while started nearly one hundred years ago, has found but a limited application in petrography and has scarcely been used at all in the more modern science of mineragraphy. This is very largely due to the methods employed, since most of them consumed too much time and were, in addition, too laborious to encourage many workers in their use. The details of procedure for these earlier methods will be found in another paper by the writer, and will be omitted from this discussion as being of small interest to practical mining men.

Jan 1, 1930

By N. M. Steven, J. M. Moore, J. L. Kuyper

Abstract - Mineral exploration and research has led to the identification of four types of tungsten mineralization in the NE-trending, largely ensialic, inland branch of the late Proterozoic/early Paleozoic Pan-African Damara Orogen. The mineralization (mainly scheelite) occurs in a terrane (the Central Zone) that is characterized by multiple deformation, greenschist/amphibolite-facies metamorphism and numerous peraluminous S-type granitic and pegmatitic intrusions. The four major types of scheelite mineralization are (in ascending stratigraphie order of host rock): (1) thin (5 cm to 2 meter) quartz+ plagioclase+ diopside ± scapolite cale-silicate granofels with finely disseminated scheelite (scheelite-bearing granofels; SBG) developed as discontinuous intercalations within the cale-silicate rocks of the Khan, Spes Bona, Oberwasser and Kuiseb Formations (Nosib and Swakop Groups); garnet+ pyroxene ± vesuvianite + scheelite ± fluorite replacement skarns hosted by Okawayo, Karibib and lower Kuiseb Formation marbles in the aureoles of late tectonic, unmineralized leucogranites; metaturbidite-hosted scheelite- (and possibly wolfrarnite-) bearing tourmalinites, both stratiform and crosscutting, in the Kuiseb Formation located in the 'cleavage fronts' of late tectonic granitoids; scheelite-bearing vesuvianite +quartz+ garnet skarnoid rocks (several hundred meters in length) in the calcareous metaturbidites of the upper Kuiseb Formation. These scheelite occurrences were discovered by the follow-up of a large number of tungsten anomalies located during a regional stream sediment sampling program. Detailed mapping, ultra-violet surveys and rock sampling proved to be the most effective surface exploration techniques for locating mineralization; soil sampling and geophysics were of almost no use. The largest, continuous scheelite-bearing skarn of economic interest, Otjua, has a drill-indicated reserve of 250 000 tonnes at 0.53 wt% W03 and 8 wt% CaF2.

Jan 1, 1994

By G. D. Bysouth, G. Y. Wong

"The Endako molybdenum deposit is located 160 km west of Prince George, British Columbia. It occurs within the main body of the Francois Lake Intrusions, a composite batholith consisting of early, middle and late intrusive phases. The ore deposit is confined to Endako Quartz Monzonite, a middle phase intrusion, which is bound on the north by Carey Alaskite and on the south by Francois Granite, both late stage intrusions. In the mine aretz, the Endako Quartz Monzonite has been intruded by pre-ore dikes of quartzfeldspar porphyry and porphyritic granite, and by post-ore dikesof basalt.The Endako deposit forms a west-northwest trending body that has a strike length of 3360 m and an apparent width of 370 m. It consists of four structurally distinct zones: Endako East, Endako West, Denak East and Denak West. Principal sulphide minerals of the deposit are pyrite and molybdenite, accompanied by magnetite and minor chalcopyrite. Galena, associated with wulfenite and bismuthinite, occurs in some ores of Endako West and Denak as minute inclusions in molybdenite. The sulphides and associated minerals are hosted by quartz veins which occur principally in vein systems. Hydrothermal alteration accompanying ore mineralization has pervasively kaolinized the quartz monzonite host rock, and has locally produced K-feldspar and quartz-sericite-pyrite envelopes on quartz veins.Primary structural controls of the deposit are southwesterly dipping vein systems which strike 110° in the Endako zones, 110° to 130° in Denak East and 170° in Denak West. Secondary structural controls are northeasterly striking vein systems that dip northwesterly in Endako East and southeasterly in Denak. Domal uplift accompanying the rise of latest stage magma is considered to have caused intense dilatant deformation along older west-northwest trending shear zones, producing an elongated structural host for ore deposition."

Jan 1, 1995

By Robin N. Adair

Abstract -The Halfmile Lake stratiform volcanogenic massive-sulfide deposit consists of pyrrhotite­ rich breccia-matrix sulfides and pyrite-pyrrhotite-rich layered sulfides that form a laterally continuous sheet stratigraphically underlain by an extensive pyrrhotite-chalcopyrite-quartz stringer zone. Mineralization is hosted by a sequence of felsic pyroclastics and volcanic-derived, fine-grained metasediments. The proportion of volcanic to sedimentary rocks indicates increasing vent proximity from southwest to northeast across the deposit area. Fine- to medium-grained felsic pyroclastics and roughly equal amounts of fine-grained metasediments comprise the stratigraphic footwall to the mineralization. Quartz-feldspar porphyritic bodies cut this sequence and may have provided the heat source for exhalite activity. Felsic tuffs, locally crystal-rich, and lesser amounts of metasedimentary rocks make up the immediate stratigraphie hanging wall. This sequence is stratigraphically overlain and locally interfmgered with matie volcanics that contain substantial proportions of felsic fragments. Deposition of sulfides post-dated the beginning of felsic volcanism, which places the deposit in the middle of the Lower Tetagouche Group. Compositions of the volcanic rocks range from basait to rhyolite and exhibit sub-alkaline affinities. Strongly overprinted whole-rock, trace-element, and REE geochemical signatures resulting from mineralizing hydrothermal activity confirm the genetic relationship be­tween the stringer zone and the mineralized sheet. Large-scale D1 folding has overturned the entire sequence. D1 thrust faults and related sheath-like folds have profoundly affected sulfide distribution. D2 is manifested by a penetrative S2 foliation, and D3 is represented by large-scale open folds.

Jan 1, 1992

By J. Hansen

"ABSTRACTThe paper addresses the application of automated monitoring, control, and navigation to improve dragline performance. SummaryImproving dragline performance in the Canadian coal mines is critical to the continued success of the industry. Draglines represent a large capital investment and coal prices are low by historic standards. This paper argues that the introduction of monitoring, control, and navigation on draglines offers an opportunity to significantly reduce a dragline’s operating cost per cubic metre moved. To place the importance of this in perspective, a North Dakota mine calculates that every 1% increase in dragline productivity means a savings to the mine of US$340,000 per year. MonitorsAutomated dragline monitoring is a well established technology with commercial products available since the early 1980s. The three main reasons for placing monitors on draglines are (Walker, 1993):1. productivity increases: reduce variations between different operators’ performance across different shifts;2. quality increases: increase the percentage of ore and waste loads that go to the correct destination; and3. special projects (engineering projects): justify installing static field exciters and regulator upgrades; implement power management; aid operator training; study high performance buckets, rigging changes, and various excavation sequences.Mines as diverse as Kennecott’s Cordero- Rojo Complex in the United States and Natal Coal Corp.’s Optimum Mine in South Africa report dragline productivity increases of 10% to 20% in the region attributed to the implementation of dragline monitoring."

Jan 1, 2000

By W. A. Alexander

Introduction In the course of a programme of research on beryllium in progress in these laboratories, knowledge of the recrystallization temperature became necessary. As the information is not available in the literature, the determination of this temperature for metallic beryllium was undertaken. By the reduction of grain size through working and recrystallization and the probable simultaneous induction of preferred orientation, it was hoped to improve the working properties of beryllium at lower temperatures. The recrystallization temperature is usually determined by observing the lowest temperature of annealing at which new crystals are formed in severely cold-worked metal or alloys. This temperature is profoundly influenced by the following factors: the purity of the metal, in the case of an element, or the composition of the alloy; the degree of straining or working; the temperature of straining; the original grain size; and the time held at the annealing temperature. The observed temperature is lowered by higher purity, more severe straining, lower temperature of working, smaller original grain size, and longer time of annealing. Beryllium presents special difficulties in that the percent elongation in tension is effectively zero, so that ordinary squeezing or rolling was not possible. A possible means of straining was suggested by the fact that indentation hardness tests could be made. It was known from earlier work that the metal could be worked at elevated temperatures, so that working at the lowest feasible temperature and quenching might also be a means of producing strain. The purity of the metal is also a point of some uncertainty in the case of beryllium. Losano has prepared 99.96% Be which appears to be the best reported. Distilled metal used in the present work approached this purity. However, by analogy with other metals, residual impurities may have a pronounced effect on the recrystallization. Further purification of beryllium would evidently entail considerable difficulties due to the highly reactive nature of the metal, and was not attempted.

Jan 1, 1947

By Rick Collins

Presentation Agenda 1.Sudbury Basin 2.Diamond Drilling 3.Planned Production 4.Safety 5.Timeline 6.Sustainable Development 7.Scope Elements 8.Progress 9.Delivery Approach 10.Owners and EPCM Roles 11.Contract Styles 12.Mine Systems & Technologies 13.Q & A

May 1, 2009

By F. G. Vetsch, F. A. Ronaghan

"Introduction1N THE FALL of 1951, Peace River Allied Fort St. John No. 1 well was drilled in Lsd. 1, Section 9 Township 83, Range 18, West of the 6th Meridian, on the flats of the north side of Peace river, six miles southeast of the village of Fort St. John, B.C. During this operation, non-commercial shows gas in three zones and of oil in one zone were obtained during the drill-stem tests. Further geological study indicated that this well was on the southeastern edge of the Fort St. St. John structure.Pacific Fort St. John No. 4, drilled shortly afterwards, obtained possible commercial gas flows on drill-stem test in five zones and thus encouraged development of what has become Canada's largest multizone gas field.In general, the productive horizons in this area possess fair per-meabilities and high porosities, a combination which provides for high reserves and moderate productivities. Development to date has therefore stressed experimental techniques in drilling and completion practice to provide high deliverability wells.Data and information of a specific nature apply, in all cases, to the pools in the Fort St. John structure."

Jan 1, 1954

By Ed Labelle, Terry Overton, Gary Bell

"LocationThe Miller Minerals lime and limestone production facility is located in the Temiskaming district of Ontario at Hailey bury on the west shore of Lake Temiskaming. Located less than 300 km from Sudbury, Timmins, Rouyn-Noranda and Val d'Or, the plant is very well situated to market products to the mining, pulp and paper, and environmental industries. Being located a few kilometres from the Trans-Canada Highway and the Ontario Northland Railway adds to transportation efficiencies.ProductsAt Miller Minerals, two principal products in various sizes are produced, which are limestone (CaC03) and quicklime (CaO).HistoryProduction of limestone products began in 1979 at this quarry site. During the 1980s, limestone products were marketed to a variety of applications for mining, forestry, environmental and agriculture applications. In 1990, the production of quicklime products began, following the commissioning of an Italian-designed vertical shaft calcining plant. During the 1990s, both quicklime and limestone products were produced to meet the customers' demands.From the quarry's conception until 1992, the operation was owned and operated by Dymond Clay Products. In 1992, it was purchased by Miller Paving Ltd. of Markham, Ontario, and became a key part of the company's industrial minerals sector of business. Other Miller interests include dolomite, cement, paving materials and waste management."

Jan 1, 2000

By N. I. Basuki, E. T. C. Spooner

"The Bongara area, northern Peru, contains Zn-Pb mineralization with characteristics typical of Mississippi Valley-type (MVT) systems. The northwest-southeast-trending late Triassic-Jurassic car¬bonate host rocks of the Pucará Group were locally replaced by early (D1) and late (D2) dolomite. Fluid inclusion microthermometric data from dolomite and sphalerite are typical of MVT ore fluids (78° to 187°C; ~15-23 wt.% CaCl2 equivalent), and do not show apparent covariation between temperature and salinity.Homogenization temperature data from D1 and D2 dolomite show a decrease from northern (mean Th = 138°C) to central (mean Th = 126°C) to southern areas (mean Th = 102°C), suggesting fluid flow from north to south. Assuming a geothermal gradient of ~30°C/km and an average surface temperature of ~20°C, the lower temperature limits might approximate the ambient host-rock temperatures, whereas the upper temperature limits may represent minimum temperatures of a deeper aquifer, probably at a maximum depth of ~6000 m. The lower temperature limits are also similar to the estimated temperatures if dolomitization and mineralization took place in the Late Cretaceous at ~2000-3000 m depth, probably during the formation of the Peruvian fold and thrust belt near the present day Peru-Ecuador border.Fluid inclusion data show that the fluids in each studied location had relatively uniform temperatures and salinities during dolomitization and mineralization. A significant salinity drop and a slight temperature decrease are observed during late calcite precipitation, suggesting mixing of brines with dilute, cooler fluids."

Jan 1, 2009

By T. A. Wedge

This paper suggests a crude correction for the impact of raw material quality on factor productivity in the Canadian mining industry. Such a correction would give a figure more dependent on the changing efficiency of the use of labour and capital, and less dependent on the effects of unquantified changes in inputs.

Jan 1, 1973

By K. Ananthanarayanan, R. I. L. Guthrie, S. A. Argyropoulos

"The low cost and availability of micro-computers and their peripherals provides the metallurgical engineer with the opportunity to use such computers in a wide variety of applications. In this paper, the authors describe the development of a low cost data acquisition system capable of measuring up to 8 analogue channels at a sampling rate of up to 5000 measure mentsper second. This system is equipped with proper hardware and software so that the micro-computer can be linked to a central computer facility such as the McGill System for Interactive Computing (MUSIC). This central computer facility is supported by an AMDAHL V7 computer. Using the present interface, communication rates between the microcomputer and the central computing facility can be as high as 9600 (baud).The above mentioned data acquisition system is currently used for monitoring dissolution kinetics of ferro-alloy additions in liquid steel. In addition to this, special software has been developed which enables the user of this system to monitor solidification rates of ingots, etc. As economic considerations are always important, comparisons have been made with existing recorders which show that the cost Of the present system is only 30 per cent more than a two-pen strip chart recorder.RESUMELa disponibilité et le bas prix des micro-ordinateurs et de leurs périphériques permet à l'ingénieur métallurgiste d'utiliser de tels ordinateurs pour diverses applications. Dans ce rapport, les auteurs décrivent le développement d'un système d bas prix pour l'acquisition des données, capable de mesurer jusqu'à huit canaux analogues jusqu’à une vitesse de 5000 mesures par seconde. Ce système est équipe avec son propre ""hardware"" et ""Software"" qui relient le micro-ordinateur d’un ordinateur central, comme le système de McGill pour computations réciproques (MUSIC). Ce central d'ordinateurs est soutenu par l'ordinateur AMDAHL V7. Utilisant cet "" interface"", la vitesse de communication entre Ie micro-ordinateur et l'ordinateur central peut atteindre jusqu'd 9600 (baud)."

Jan 1, 1980

By S. Komar Kawatra, Youlian Zhou, Joseph A. Halt

"Bentonite clay has been the most common binder for iron ore pellets. Although bentonite increases pellet strength and durability, it has several disadvantages. For example, its use increases the cost of pellets and decreases pellet purity due to its composition and the higher levels of flux required to meet basicity limits. Several new types of binders have been proposed to replace clay. The binders include starch, modified humic acid (MHA), and dispersants. These binders were used to pelletize a magnetite concentrate from the United States. Typical doses of each binder type were 0.05-0.1 % starch, 0.5-0.75 % MHA, and 0.05 % dispersant. At these doses, the pellets exceeded the minimum recommended values for wet drop, dry compression strength, and fired compression strength. Pellets made with the MHA and dispersants had the lowest abrasion rates of the new binders, and were comparable to pellets made with bentonite clay. In this paper, we compare the new binders, considering pellet quality and the advantages and disadvantages of each binder type.INTRODUCTIONIron ore pelletizers need binders in order to make good quality iron ore pellets. The typical binder is bentonite clay, an alumino-silicate material. Bentonite increases the ballability and strength of iron ore concentrates, but reduces pellet iron grade and reducibility. As high quality bentonites can be expensive to ship, low quality bentonites are often used at significantly higher doses – this reduces iron grade and reducibility even further. Thus, several new types of binders have been proposed to replace bentonite clay.In this paper, we present several new binders for iron ore pellets: starch and modified humic acid (MHA). These have been tested alone and in mixtures with dispersants, or else with bentonite clay. Starch, MHA and their mixtures are briefly described below."

Jan 1, 2016

By G. I. Mathieu

"An experimental study was carried out to evaluate the performance of column flotation versus conventional flotation for the recovery of molybdenite from a Newfoundland ore. The objective was to verify the claims made by the inventors of the flotation column, Messrs. Pierre Boutin and Remi Tremblay, that their apparatus reduces the entrainment of fine gangue and other mineral impurities in the froth product. The research included a factorially designed series of tests to determine satisfactory operating conditions of the column. These provided a basis for comparative flotation tests with column and Denver cells. In the course of the work, the action of a few depressants was studied. Results indicated greater selectivity in the column and reduced reagent consumption."

Jan 1, 1972

By P. R. Geoffoy, T. Koulomzine

"The discovery of the Mogador deposit concealed by 100 feet of overburden was the result of combined application of geological reasoning, ground geophysical surveys, studies of glacial float and extensive diamond drilling. The ground was acquired because it lay on the projected intersection of the Manville and Laflamme River faults. Systematic ground prospecting led to discovery of mineralized floats. A first unsuccessful exploration campaign lasted several years and consisted of 137 drill holes.In 1951 the boulder nests were reexamined and an associat'on of the mineralized float with boulders of a granodiorite, unknown in outcrops of the district, was established. Consequently, ground magnetic surveys were extended and re-interpreted, and a large anomaly interpreted as corresponding to a batholith was outlined. The existence of the batholith was immediately confirmed by drilling and the Mogador deposit discovered in third hole of new drilling programme in a zone of fractured volcanics paralleling southern contact of batholith.The Mogador deposit is a complex replacement of silicified volcanics by pyrite, pyrrhotite, sphalerite, chalcopyrite and galena carrying values in silver and gold. A total of 1,230,000 tons has been indicated, most of it now classified as fully developed proven ore."

Jan 1, 1960

This paper deals mainly with the modernization in the coal loading system at the loading piers of the Dominion Coal Company, Ltd., Sydney, Nova Scotia. The history of the operation is briefly outlined, and the construction of the Company's new pier is described in considerable de-tail. Particular attention is paid to the bins and conveyors, and to the loading tower. The paper concludes with a description of the S.S. Cape Breton Miner, built specifically for the coal trade, and the unloading facilities at Lakeview, Ontario. Coal Shipping at Sydney C OAL from the mines operated in Cape Breton by the Dominion Coal Company, Limited, has been shipped from the International Piers, situated on the east side of Sydney Harbour, for over sixty years. There were three piers, of which two were active-ly used in the shipping of coal until 1964. Nos. 2 and 3 were high piers about 600 feet long, of wooden construction throughout. They were founded on' rock-filled cribs and creosoted piles driven into the harbour bottom, and each had two decks which carried standard-gauge railway tracks.

Jan 1, 1965

By M. G. Lipsett

"The Mining Information Technology User Group considers information to be a strategic enabler to improved business performance in mining. This ad hoc group has been meeting since 2000 to share knowledge and leverage their efforts in effectively using IT in mining. In this paper, core issues to mining IT are reviewed, along with initiatives to engage industry professionals and decision-makers in the potential for improved use of information in their operations. Relevance of IT to Canadian MiningMining operations always drive to improve their performance, and so far they have succeeded by using different technologies. While economies of scale have come in fragmentation and material handling, and energy usage has improved through conservation and design of integrated mineral processing plants, these systems have the net result of tightening operational constraints, through reduced excess capacity. There are higher opportunity costs of lost production when integrated, large-scale systems are operating in a sub-optimal way.The problem is that it is profoundly difficult to run a mine in an optimal way. Optimization requires a defined objective function (e.g., profit), which is hard to pose, let alone solve, because so many inter-related aspects of an operation affect the bottom line. Even for a small, well-defined process state, it is difficult to measure all the pertinent information with sufficient accuracy to ensure that the system is performing well in real time.The art of mining remains making good decisions with uncertainty: in the orebody delineation; in the allocation of resources; in the efficiency of the operation; in the reliability of components and systems; and in responding to the downstream market. As well, individual decision-makers need to know how their decisions affect other processes and systems, so that improvements in one part of an operation do not result in such degraded performance in the rest of the plant that overall profitability goes down."

Jan 1, 2003

By H. C. Gunning

DURING the past year the Cadillac-Malanie area in northwestern Quebec has been catapulted to the front as one of Canada's most active gold mining districts. Late in 1934 the area was lolling along in the doldrums, with one producing mine and a handful of active prospects. 1935 passed with only slightly increased activity, but saw the start of production at Canadian Malartic mine. Lightning struck in April, 1936, when a new and phenomenally rich ore-body was found in O'Brien Gold mine, and by midsummer the camp was ablaze with activity. An important new discovery on the Pan-Canadian property, and pleasing underground developments at Sladen Malarric, East Malartic, and Lapa Cadillac, in addition to other new developments, lent fodder to the flame, and at present several dozen properties are being actively developed. For the past three seasons, the Geological Survey of Canada has been engaged in a fairly detailed study of the geology and mineral deposits across Cadillac, Malarric, and Fourniere townships. Ir is the purpose of this paper to present a brief preliminary statement of the structural and economic geology and to discuss some of the more important problems that have been found to exist. The reader is requested to remember that the paper is a preliminary one and that therefore the conclusions presented are open to revision. It is impossible to make full acknowledgment for help received, for the writers are indebted to practically every operator and prospector in the area for generous co-operation in the work, and to several private, provincial, and federal geologists for data and frank discussion of problems encountered. Over a score of student assistants from McGill, Queen's, and Toronto have given excellent service. Published reports by Wilson, Cooke, James, Mawdsley, L. V. Bell, and J. J. O'Neill greatly facilitated the work. For adequate control surveys and a topographic base-map, the writers are greatly indebted to H. N. Spence.

Jan 1, 1937