Search Documents

By CH. Liu, H. X. Jiang, X. Xiao

"A study has been conducted to characterize the fatigue life in 7050-T7451 thick plate by the comparison between an experimental alloy and commercial alloy. The fracture origins were specified and their sizes were measured by scanning electron microscope (SEM). Additionally, the size, number density and spatial distribution of porosity in the experimental material and commercial material were characterized and compared, using X-ray Computed Tomography(XCT). The results showed that microporosity was the predominant site for crack nucleation and subsequent failure of the experimental alloy. However, as for the commercial alloy, fatigue cracks were found to originate from constituent particles. The presence of microporosity in 7050-T7451 thick plate reduced fatigue life of an order of magnitude or more compared to the commercial alloy. The relationships between size of origin and fatigue life were proposed. It was showed that the fatigue endurance was reduced when the size of porosity increased.INTRODUCTION 7xxx series aluminum alloys, due to their combination of high strength, high resistance to stress corrosion cracking, and good fracture toughness, are widely used in structural engineering applications where high-strength and low-density characteristics are fundamental design requirements (Williams& Starke, 2003). Every designer is striving to find an optimal combination of properties including strength, corrosion resistance and fatigue resistance (Wanget al., 2016). Based on the design principles of aircraft, a higher fatigue resistance of aluminum alloys are required. Thus, many investigations have been carried out on the microstructures and its effect on fatigue properties of the 7xxx series aluminum alloy (Robson, 2004; Schubbe, 2009).Microporosity, which is a common defect in casting materials, can lead to a significant deterioration of mechanical performance and fatigue resistance, especially in the high alloyed 7xxx aluminum alloys. The actual valid loading area decreases due to microporosity, which results in detrimental effect on the mechanical properties. Many experimental studies have been conducted in this research field. Mayer et al.(2003) investigated the fatigue properties of magnesium alloys produced by high-pressure die-casting. The results show that porosity in magnesium alloys greater than0.18mm diameter may be considered as the most important material defect for high cycle fatigue and fully reversed loading conditions. Nadot et al.(2004) found that the near surface defects are much more dangerous than the internal defects. Wang et al.(2001a) used the Weibull statistics method to analysis the influence of the microporosity, oxides and particles on the A356-T6 alloy fatigue life. The results show that, the porosity is more detrimental to fatigue life than oxide films and particles. With regard to fatigue resistance, although the deleterious effect of microporosity has been generally acknowledged, a quantitative understanding between casting microporosity and fatigue life in 7050-T7451 plate is not well established."

Jan 1, 2018

By Young Hyun Paik, Hyung Sup Choi, Yeun Sik Kim

The basic studies on the surface properties and flotation characteristics of ilmenite were made by electrophoretic, adsorption, contact-angle and floatability measurements. The isoelectric point of ilmenite is found to be at pH 5.6. By combining the results of electrokinetic studies and adsorption measurements, a clearer picture of the ilmenite-solution interface was observed. These findings were correlated with the floatability of ilmenite obtained by Hallimond tube tests. The general flotation characteristics of ilmenite are compared with those obtained for magnetite and rutile. It is indicated that the above three minerals, namely, ilmenite, magnetite and rutile, have very similar surface properties and flotation characteristics. Therefore, it is difficult to make an effective separation of these minerals by flotation. However, it is found that sodium orthophosphate acts as a selective depressant for magnetite in anionic flotation. Therefore, close pH control of the pulp in the presence of the phosphate ion enhances the possibility for a successful separation of these minerals.

Jan 1, 1967

By P. G. Semple

"In January 1985, Equity Silver Mines Limited began operation of a cyanidation circuit to scavenge precious metals from the flotation tailings. At present, this process is treating 270,000 tonnes of tailings per month and is recovering in excess of 0.20 grams of gold per tonne. To obtain these results Equity is operating a carbon-in-leach circuit that utilizes pressure stripping, zinc precipitation acid washing and thermal reactivation. A cyanide destruction circuit is also required to minimize the deleterious effects on reclaim water in the flotation stage. This paper describes the existing scavenger plant, and details the start-up problems encountered and the modifications made to correct these problems.INTRODUCTIONEquity Silver Mines Limited , a 68% owned subsidiary of Placer Development Limited , is located 38 km southeast of Houston in north central British Columbia. The geographic location of Equity Silver Mines is shown in figure #1. In September 1980, production first began with the ore being supplied from the Southern Tail open pit. In March 1984, the Southern Tail deposit had reached its economic pit depth, and since then ore has been supplied by the Main Zone pit the gold mineralization in the Main Zone is less refractory than the Southern Tail and cyanidation of the flotation tailing appeared to be a viable alternative.An extensive test program was undertaken and the results confirmed that considerable gold and silver values were amenable to cyanide leaching. A feasibility study showed that these values could be economically recovered and the detailed engineering work began."

Jan 1, 1987

By H. D. B. Wilson

THIS PAPER has resulted from a preliminary draft of a background paper prepared anonymously for the Science Council's Special Study of the Solid-Earth Sciences in Canada. The draft was circulated to eighty-four Canadian geologists; forty-eight of these responded with criticisms of the draft. All critical re-marks were considered carefully and most have been incorporated in the final paper in an attempt to balance the author's bias, although this bias undoubtedly still appears. Indications of support for a particular statement or section were also helpful, because many of these contradicted criticisms and enabled the author to judge the consensus. Thus, all criticism could not be incorporated because the referees did not agree. It is interesting that some remarks were con-sidered overstatements by some and too bland by others. The most perplexing critical comment was one which suggested a new author was needed, and went on to name the existing author as the most likely candidate.

Jan 1, 1970

By E. G. Joe

"This paper summarizes the main conclusions derived from twenty-two technical presentations made at the 1973 meeting of the Canadian Mineral Processors. Results of two surveys with response from over seventy mines were reported on Canadian milling practice for water re-use and on elimination of cyanide from mill effluents. Water and solution recycle in Canadian mills were detailed for copper, copper-zinc, lead-zinc-copper, nickel-copper, iron and gold mines. Cyanide elimination from mill effluents was reported under current practice and under requirements for further treatment by various other processes. Three recent process equipment entries into Canadian mills have been the on-stream particle analyzer, the new gravity concentration tables for recovery of fine tin and other heavy minerals, and solution-jet slurry equipment for reclaiming ground ore from storage. The principles of operation of this equipment were described along with the practical limitations that were found in their application to mineral processing. Capital costs and milling cost reductions were shown in some operations. Computer control of flotation mill processing was a major item on the program. Four major mining companies outlined their mill process control strategy, computer programs and on-stream analysis equipment. Some capital costs and personnel changes were presented, together with gains in concentrate grade and mill recovery. Recent development work has shown the effect of the type of grinding and of aeration on the recovery of sulphide minerals in flotation. One mining company reported a significant depressing effect on copper sulphide flotation while floating ore ground with mild-steel balls; also, pyrite appeared to be activated in the subsequent zinc flotation step. One company with extensive experience in the application of aeration to copper sulphide flotation showed significant improvement to copper recovery by pre-aeration. Both the effects of grinding and aeration were subject to the constraints of the chemical condition of the ore pulp. The metallurgy of silver recovery by combination grinding - gravity treatment and of gold recovery from a complex gold-sulphide ore were reviewed in two papers on precious metals. The latter paper further described the recovery of gold from the Cottrell collectors and the final disposal of arsenic from the dust collectors."

Jan 1, 1973

By J. A. Finch, A. M. Elmahdy

Blending frothers is becoming common in flotation practice apparently enhancing performance. However, there have been no studies to understand the blend mechanism. In this paper, the effect of two frother blends ofF150 (polyglycol) with MIBC or pentanol (both alcohols) on bubble size, gas holdup and froth height is reported. The blends focused on a small addition of the polyglycol to the alcohols as base frother. The tests showed that the bubble size at blend concentration below the critical coalescence concentration (CCC) of the base frother was decreased but was significantly larger above the base CCC. Froth build-up showed a strong synergistic effect.

Jan 1, 2009

By M. Korchynsky

"The key words which characterize vanadium are: unlimited availability, versatility of applications and price stability. The supply of vanadium is assured by diversified sources, distributed all over the globe. The inexhaustible raw materials base is complemented by a strong vanadium industry. Both the fully integrated vanadium producers and converters of vanadium oxide or vanadium-containing slags or residues guarantee an adequate supply, commensurate with the steady growing demand.The major share of the world's vanadium output is being consumed by the steel industry. As an additive to steel, the versatility of vanadium is particularly impressive. A few hundreds of one per cent of vanadium convert plain carbon steel into high-strength, low-alloy steel with more than double strength. On the other extreme, high-speed steels made via the powder metallurgy route show superior performance with vanadium additions as high as 6 or 8 percent. Vanadium is used as a cost-effective alloying addition in steels for high-temperature service, fully alloyed heat-treatable steels, new dual-phase steels for automotive components, rail steels, etc., to mention only a few applications. Vanadium is also an established essential addition for titanium alloys. The chemical industry is relying on vanadium compounds as important catalysts.In spite of a wide diversity of applications and continual growth in consumption, vanadium has exhibited, over the past several decades, a remarkable price stability, free of conjunctural fluctuations. Because of its availability and versatility, it will continue to be one of the key metallic elements for future technologies.Key Features of VanadiumIn attempting to single out the key features of the metallic element vanadium, three descriptive characteristics come to mind: availability, versatility and price stability."

Jan 1, 1982

By F. W. Brackebusch, R. O. Sack

"A method for determining the fineness of Au in electrum from the composition of fahlore coexisting with pyrite and chalcopyrite is presented. This method is based on previously published experimental brackets and activitycomposition models for electrum and fahlore, and it is potentially useful for defining temperatures of hydrothermal mineralization and retrograde evolution of precious metals deposits. The authors demonstrate that it successfully predicts compositions of electrum reported for this assemblage in the literature and illustrate its application for three gold-quartz vein deposits from the Coeur d’Alene mining district, Idaho, that are prospects of the New Jersey Mining Company, the Coleman vein, High-Grade prospect, and Silver Strand mine. Temperatures calculated from average electrum compositions estimated from gravity concentrates (molar Au/(Au+Ag) = 0.76-0.39) and from microprobe analyses of the fahlores (molar Ag/(Ag+Cu) = 0.039 ± 0.004, Zn/(Zn+Fe) = 0.57 ± 0.03, As/(As+Sb) = 0.23 ± 0.02) from the Coleman vein indicate that the electrums underwent retrograde re-equilibration to temperatures between about 80°C and 240°C, roughly 80°C below the temperature of hydrothermal mineralization and 10°C to 40°C above the temperature inferred for retrograde equilibration of Fe and Zn between sphalerite and fahlore. Fahlores from the High-Grade prospect [molar Ag/(Ag+Cu) = 0.009 ± 0.004, Zn/(Zn+Fe) = 0.55 ± 0.11, and As/(As+Sb) = 0.04 ± 0.03] and Silver Strand mineralized zone [molar Ag/(Ag+Cu) = 0.10 ± 0.04, Zn/(Zn+Fe) = 0.63 ± 0.02, and As/(As+Sb) = 0.06 ± 0.02] exhibit strong core to rim depletions in Ag due to retrograde operation of the reaction1/10Cu10Fe2Sb4S13 + Ag + FeS2 =Cu-fahlore electrum pyriteCuFeS2 + 1/10Ag10Fe2Sb4S13chalcopyrite Ag-fahlorewhich proceeds to the left with decreasing temperature. Electrum inclusions in arsenopyrite from the High-Grade prospect [molar Au/(Au+Ag) = 0.90 ± 0.02] define a minimum bound on the temperature of hydrothermal mineralization of 273°C, and the temperatureelectrum composition curve constructed for the most Ag-rich fahlore in the Silver Strand mine indicates that the fineness of its electrum is significantly less than in the other deposits."

Jan 1, 2004

By Dao Dac Tao

The Vietnam coal industry in recent years has achieved the rapid growth. However, in the process of industrialization and modernization of the country, the demand for coal for energy is constantly increasing. This paper presents the Vietnam coal industry in the last stage: the opportunities and challenges facing the coal industry as it strives to become modern, highly effective and capable of meeting the demands of national energy security, all in harmony with socio-economic and environmental needs.

Aug 1, 2013

By K. Jomoto, H. Majima

"Experimental work has been attempted to find a useful criterion of comminution which can be determined simply in a laboratory. The suitability of the ratio of the square of tensile strength to Young's modulus, St2/E, previously derived from the theory of elasticity as a criterion of comminution, was examined measuring tensile strength, Young's modulus and critical height for drop-weight impact of five different rocks. However, satisfactory correlation between St2 /E and critical height has not been obtained, suggesting the necessity of further experimental verification of the representative value of Young's modulus of rocks. The plot of St2 vs. critical height, however, shows one-to-one correspondence, and this finding suggests that St• may be a useful criterion of impact crushing. Also, a close relationship was observed between st• and the energy index for tumbling mill grinding of •the sample rocks. It is confirmed from these findings that the quantity St• is a useful criterion of comminution of rocks, not only for impact crushing but also for tumbling mill grinding. As shown in the experimental part of this paper, the determination ol St with irregularly shaped specimens is simple."

Jan 1, 1972

By A. E. McIlhinney, I. E. Puddington, C. E. Capes, A. F. Sirianni

"Two main problems are associated with the removal of pyritic sulphur from coals. The first is due to the fine state of dissemination of pyrite, which requires grindin1 to a very fine size to accomplish liberation. The second problem is caused by the similar surface chemical characteristics of coal and pyrite, which complicates separatio11 methods based on this property. In the work described here, the problem of fine particle size was overcome by using the selective oil agglomeratioa method developed at the National Research Council of Canada. Recovery of more than 90% of the combustible values was possible, even with particles only a few microns in diameter. Experiments using conventional chemical depressants for pyrite met with little success. It was found, however, that pyrite may be rejected during coal agglomeration through treatment with the iron.oxidizing bacteria, thiobacillus-ferrooxidans. The conditions for maximum pyrite separation are described and possible mechanisms by which the bacteria act are discussed."

Jan 1, 1973

By G. Dubé, A. Leclerc, P. Quinn, G. E. Agar, J. Y. Clouthiér, J. D. McLaughlin

"Gold dissolution by cyanide requires the presence of oxygen which is usually supplied by sparging compressed air into the gold containing slurry. For those ores that contain certain obnoxious substances that consume oxygen, maintaining the required minimum level of dissolved oxygen can be troublesome. One of the most economical solutions to the problem of low dissolved oxygen, especially in plants that have air compressors installed, is to enhance the rate of oxygen mass transfer.The oxygen mass transfer rate was measured in a two phase system using two different sparger arrangements, and with addition of a frother that is known to reduce the bubble size produced by the sparger. The common sparger system was shown to be inefficient compared to a readily available but under utilized method of gas dispersion which introduces air directly below the reactor turbine. Transfer of this technology to an operating plant confirmed the beneficial effect of the improved sparger system. The addition of the frother did decrease the bubble size, but it also reduced the oxygen mass transfer rate."

Jan 1, 1993

By DALE MacGREGOR, VERA TUREK

The Blue Mountain nepheline syenite deposit has been the subject of several detailed studies. It has been variously referred to as an intrusive stock, a metasomatic deposit, an intrusive sill and a metamorphic-metasomatic body. The body is divided into six mineralogical zones, the first five being based on the characterizing accessory mineral; muscovite, muscovitemagnetite, biotite-muscovite, biotite, hornblende and pink syenite. Mining currently takes place only in the biotite zone. Foliation is particularly prominent in the central (hornblende) zone and near the margins of the nepheline syenite. Majic bodies within the nepheline syenite may represent basic rocks that have been less altered by metasomatism, metamorphosed basic dykes or sloped blocks of metasediments. The most prominent structural features are the northeast-trending folds that have been modified by later north west-trending folds.

Jan 1, 1984

By S. Banisi, M. Maleki-Moghaddam

Direct observation of charge shape and its motion in industrial mills is not possible; therefore, a combination of analytical and physical studies is used to determine charge trajectory. Software packages, which predict charge motion consider only the outermost layer of charge (single ball) and ignore the charge and the interactions of grinding elements. In the new version of the GMT (Grinding Media Trajectory) software, the effect of liners specification and bulk load on charge shape and trajectory are considered. The charge trajectory was measured in a laboratory mill with the diameter of 100 cm and length of 21.5 cm with the transparent end and compared with that of the old version of GMT. Four types of polyurethane rings were accurately machined to scale down the liners arrangements at two industrial mills. The model mill was operated at 55, 70 and 85% of the critical speed for five levels of mill filling (10, 15, 20, 25% and 30% by volume). The experiments indicated that the end walls effect was negligible for the model mill with the length of 10.8 cm and beyond. The proposed relationships to correct the trajectory and charge shape were validated by using the new liner of the Gol-E-Gohar iron ore company AG mill. The positions of shoulder, toe, toe departure and impact points were predicted with the relative errors of 5, 0.7, 2 and 0.2%, respectively. The GMT software was updated with the new relationships. The results of GMT simulation indicated that when the lifter face angle increased from 7 to 30°, the distance between the charge impact point and the toe decreased from 40.1 to 11.2° for 30% filling. The change in the position of the impact point meant increasing the probability of charge impacting the toe, not the liner which favored more efficient comminution practice.

Jan 1, 2016

By L. Xu, A. Vazirnegad, R. Bhaskar

"Respirable dust samples are collected by the U.S. Mine Safety and Health Administration (MSHA) and mine operators as part of the requirements of the Federal Coal Mine Health and Safety Act of 1969. About 1.85 million respirable dust samples collected by MSHA were analyzed for the period 197/ to 1990 f or the states of Alabama, Colorado, Illinois, Kentucky, Ohio, Pennsylvania, Utah, Virginia, and West Virginia. Trends in coal dust exposure of continuous miner operators, helpers, and roof bolters were analyzed. The reported production in each of the nine states was analyzed. The relationship between average dust exposure and coal production was evaluated. In addition, the differences between mine operator and MSHA inspector collected data were examined for each state. The average exposure levels for the three occupations - miner operator, miner helper, and roof bolter were also compared.The data indicate that the dust exposure levels have significantly dropped over the last twenty years, while at the same time production has increased, attesting to the ability of the U.S. mining industry to adapt successfully to the stringent dust control regulations. In terms of coal production, it appears that some states, such as Utah, Illinois, and Kentucky, were able to increase their production significantly relative to others, such as Pennsylvania and Virginia. The relationship between dust concentration and coal production is, at best, tenuous. 11 implies that existing dust control technology has assisted several mine operators to meet dust standards, while, at the same time, enabling mines to produce more coal than before. Comparison of data collected by MSHA and mine operators indicate that MSHA inspectors recorded higher dust levels and lower shift production relative to mine operators."

Jan 1, 1993

By I. P. Barbosa, P. S. M. Soares, I. O. C. Masson

"Permanent magnets have been applied extensively to several electronic products such as printers, TV sets, microphones, microcomputers and headphones, presently manufactured in large scale by industrial economies. Sm-Co alloys represent about 20% of the world market for permanent magnets and their industrial processors generate 20-30% of magnetic scraps which can be recycled. This paper discusses a process route to recycle SmCo5 using acid treatment, solvent extraction of Sm and electrowinning of Co. The results confirm the feasibility of the alternative proposed. Basic operational variables are suggested as guidelines to design a plant for recycling magnetic scraps.The use of hydrometallurgical processes to recycle scraps from the industry of permanent magnets has been suggested in some recent papers related to recycling of metallic alloys [ 1 ]. These research efforts might be understood as a worldwide tendency towards the development of self sustainable metallurgical processes which mean the reduction of environmental impacts.CETEM -Center for Mineral Technology leads in Brazil several research programs concerning recycling and treatment of industrial residues. The work on samarium purification and concentration by solvent extraction, producing also a solution of cobalt sulfate as partially reported here is one of these programs. Previous results related to the sulfuric acid digestion of SmCo5 are presented somewhere else [2]"

Jan 1, 1997

By S. Huang, K. Xia

"During crushing, rock particle is subjected to complicated loading and the particle shape influences the fragmentation outcome. Thus, a highly controlled laboratory test is desired to establish the relation between the loading and the fragmentation parameters for better understanding the rock crushing mechanism. In this work, a split Hopkinson pressure bar system in combination with high speed cameras is utilized to carry out a dynamic ball compression test, in which the spherical rock sample is adopted to avoid the shape effect. Using the elasticity theory, the history of the axial symmetric tensile stress perpendicular to the diametrical direction along the loading axis is determined, from which the loading rate and the dynamic indirect tensile strength are calculated. With the aid of the moment-trap technique, the total energy absorbed by samples is accurately determined from the one-dimensional wave analysis. Furthermore by considering the kinetic energy of the sample fragments using the high speed camera snapshots, the surface energy is determined for each sample. The relations between the loading rate and the fragmentation parameters, i.e., the number of fragments and the surface energy are established. The application of this method to a granitic rock shows that it is flexible and can be applied to the crushing study of generic brittle solids. INTRODUCTIONCrushers are widely used to break rocks to extract specific minerals in the mining industry, and to obtain rock fragments with desired size distribution in construction industry. During crushing, the breakage of particles can be in either the single-layer mode or the multi-layer mode. In the single-layer mode, the particle breakage can be assumed to be isolated, in which the interaction between particles can be ignored. It is thus suggested by many researchers that highly controlled single particle test should be performed to establish the relation between the input mechanical energy and size reduction for better understanding the crushing mechanism (Yashima et al., 1987; Tavares, 2007; Pitchumani et al., 2004)."

Jan 1, 2015

By Jack Zhang, Chuck Edwards

"The versatility and specificity of rare earth elements (REEs) have led to their use in an ever increasing variety of applications in new technologies. Consequently, demand for REEs has increased significantly. However, to separate REEs safely and effectively is a complex and expensive process. While China has consistently invested in R&D of REE processing technologies, there have been only sporadic activities in REE mineral processing in North America in the past 20 years. This paper presents a review of REE mineral processing technology, providing an update on current capabilities in REE mineral processing. This paper reviews REE extraction from the major commercially valuable REE-bearing minerals such as bastnaesite, monazite, and xenotime, and also from the ion-absorption type of REE deposits. Currently, there are four major REE mining areas in China, one in the United Sates, and one in Australia. A review of the REE extraction processes in these major REE mining areas closes out the paper.INTRODUCTION The rare earth elements (REEs) include the 15 lanthanide elements, plus yttrium and scandium. The lanthanide elements are normally categorized in two groups: the light rare earth elements (LREEs), i.e. lanthanum through europium (atomic number (Z) = 57 through 63); and the heavy rare earth elements (HREEs), i.e. gadolinium through lutetium (Z = 64 through 71). Yttrium is usually grouped with the HREEs due to similarity in physical and chemical properties. Table 1 lists the REEs, atomic numbers, and abundances in earth’s crust (Taylor and McCleannan, 1985). Promethium is the rarest due to lack of stable isotopes. REEs with low atomic numbers are more abundant than those with high atomic numbers. More interesting is that the REEs with even atomic numbers are much more abundant than adjacent lanthanide elements with odd atomic numbers as shown in Table 1."

Jan 1, 2012

By Raymond J. Pichette

"Aeromagnetic data can be useful in helping to delineate structures and rock types in gold exploration. Magnetic anomalies associated with Archean volcanic belts in northeastern Ontario can be quickly and effectively analyzed in profile form with the use of model curves. The model curves help to locate contacts between strata. They also help to estimate the magnetite content of the rocks and their depth beneath overburden.An aeromagnetic map of part of Catharine Township, Ontario has been analyzed with the aid of model curves. Several magnetic rock types, potential fault zones and areas of relatively thick overburden were delineated.IntroductionIn any exploration program, a good understanding of the stratigraphy, rock types and structure enhances the possibility of success. For example, environments which host gold deposits in the Abitibi Volcanic Belt may be characterized as follows (Jensen, 1980; Pyke, 1980):(I) They have major faults, especially as tectonic boundaries between volcanic piles which include mafic and ultramafic rocks and clastic sedimentary rocks or gneisses.(2) They have subvolcanic felsic intrusions.(3) They have extensive carbonitization, with or without carbonate and sulphide-facies iron formation.In all cases, delineation of structure and rock type should be a major objective in exploration. The analysis of magnetic data can be a useful tool in this task. This paper is presented with the purpose of describing the application of the magnetic method to gold exploration in Archean volcanic terrains.Magnetic AnalysisTotal-intensity magnetic contour maps can be used to discriminate rock units according to differences in magnetization. However, because of smoothing of texture resulting from the compilation procedure and the fact that survey lines are widely spaced, contours should not be directly used for quantitative analysis. A much more definitive means of magnetic analysis is provided by the use of the original profile or chart recordings. Model curves provide a basis for analyzing these profiles both accurately and rapidly."

Jan 1, 1982

By David M. Parkes, George E. Davies

"Mathematically, the proposed formula is: ""Human Effectiveness + Technological Improvement = Success in the Nineties"". A brief review is made of geology, level of technology, management and labour situations, and range of production costs in coal producing countries. This comparison shows keen competition for Canadian coals, especially from the People's Republic of China, South Africa and Australia. Domestic competition comes from nuclear energy, hydro-electric generation, natural gas (if permitted) and eastern United States coal.The huge increase in the size and power of surface mining equipment in the last forty years led to modern large-scale open pit mining. While conventional truck and shovel operations will continue to be widely used, more continuous mining and conveying systems will be installed as pits become deeper and haul distances longer. Computer systems will become more sophisticated and their applications more widespread, leading to higher productivity and closer control of all operations and equipment performances and to partial or complete automation of certain operations.The underground revival will be driven by a new generation of mining people, cooperating to produce over 3 million t/y from 300 m longwall faces retreating over 3 km resulting in mine productivities of over 40 tonnes per man shift, as is already achieved in several mines throughout the world. Continuous operation using on-line control system will assist in consistent production with availabilities over 75%."

Jan 1, 1991