Search Documents

By J. D. Bliss, G. J. Orris, W. O. Menzie

"Analysis of gold placer data from gold placers throughout the world suggests that gold grades and volumes cannot be used to distinguish between most types of gold placers. Only the alluvial plain and fan placers are significantly different among the types of gold placers considered. Gold grades and volumes change when working gold placers go from small-volume methods to large-volume methods. The small-volume methods are either of the surface or subsurface (drift mining) type. The odds that a gold placer will be dominantly worked using small volume methods at the surface are about 5:3. Once small volume mining has occurred, the odds against subsequent large-volume mining are about 4:1. If a placer deposit is suitable for large-volume mining, and the amount of gold produced from small-volume mining was reported, an estimate of the remaining gold (log10kg) can be made using the following equation:The relationship shown by this equation suggests that very large gold placers have over half their total gold content in the rich gravels appropriate for small-volume mining. These relationships in conjunction with other data and computer simulation can be used to estimate placer gold resources for an area targeted for mineral resource assessment. IntroductionGold placers have been an important source of gold throughout man's history and may have been one of the first sources-dating back to around 6000 B.C. (Gregory, 1980). From the primitive basket to the modern floating dredge, a variety of methods have been used to work gold placers. Placers are found in a wide spectrum of geologic and climatic settings. They have been classified by using a mixed set of criteria including age (Recent, Tertiary), climate (desert), fluvial position (modern channel, bench, alluvial fan), environment of deposition (eluvial, alluvial, residual, beach), type of transport (stream, wind, glacier), and whether the placer is buried or at the surface (Boyle, 1979; Wells, 1969). Several mining methods have usually been used to extract gold from anyone placer."

Jan 1, 1987

By R. B. Paine, B. M. Wright

"Syncrude has entered a new era involving the use of pipeline slurries to convey oil sand to the extraction plant. Hydrotransport operations and base plant operations encounter vast performance differences when processing different types of oil sand. This paper describes the hydrotransport process, its history at Syncrude, methods of describing the source ore characteristic and plant performance. The use of this information within Syncrude and how it will be managed on an ongoing basis will also be described. IntroductionThe Syncrude Canada Ltd. site is located 43 km north of Fort McMurray, Alberta, on the Athabasca oil sand deposit. The Syncrude operation consists of mining, extraction, upgrading, utilities and other support facilities. The mined ore is sent to the extraction plant where water and solids are removed from the bitumen. The bitumen is then sent to the upgrading plants to be further processed into Syncrude Sweet Blend (a light sweet crude oil). Syncrude produced 73.5 Mbbls of Syncrude Sweet Blend in 1996 and produced 75.7 Mbbls in 1997. Prior to 1993, Syncrude moved ore from the pit to the extraction plant via four dragline / bucketwheel/ conveyor systems. These systems, supplemented by auxiliary ore crushers, satisfied the feed requirements of the extraction plant. Ore was conveyed to the control tower area and placed in the dump pocket via four radial stackers. Various blending scenarios occurred at this point, using feed from the four mining quadrants and from auxiliary feed crushers. Upon entering the extraction plant from the base mine, the oil sand passed through a series of tumblers where it was mixed with hot water and caustic. It then proceeded to one of four primary separation vessels where bitumen froth was floated off and the middlings and coarse fractions were recombined and sent to the tail oil recovery vessels, or TORs, for further processing."

Jan 1, 1999

By S. M. Bulatovic, D. M. Wyslouzil, K. R. Rawlings

"The suitability of a new organic reagent DS20 as a depressant for oxidized and carbonaceous pyritic lead-zinc ore from Nanisivik Mines Ltd. has been evaluated in the laboratory and in the plant.The depressant DS20 is a mixture of Lignosulphonate-Dextrin-Quebracho and was developed specifically for depression of highly oxidized and carbonaceous pyrite.The laboratory test work indicated that the poor metallurgy resulting from the oxidized ore could be improved to normal plant performance by the addition of the DS20 depressant with the existing plant reagents. The laboratory data suggested that lime consumption could be reduced when using DS20.In this paper, the development work and the plant trials with DS20 are described.INTRODUCTIONNanisivik Mines Ltd. treats approximately 2000 tonnes per day of lead-zinc massive sulphide ore, containing currently 1% Pb and 9% Zn. The concentrator operations have been described previously (1,2) and typical metallurgical performance is detailed in Table I.The concentrator flowsheet (Figure No. 1) and the standard reagent scheme (Table No. 2) demonstrate the relative simplicity of treatment of this coarse grained ore.A recently discovered satellite orebody - Area 14 - containing 2% Pb and 12% Zn was brought into production in October 1983. This ore had been oxidized to varying degrees by ground water; the pyrite mineralization was found to be very fast floating and a carbonaceous constituent present in higher than normal proportion also affected flotation. The simple high lime addition could not control the pyrite, and very low grade lead concentrates resulted; zinc metallurgy was also affected by this oxidized condition (Table 3)."

Jan 1, 1986

By M. Fiset, D. Belley

"In a country with a cold climate like Canada, the cost of replacing worn parts of snowplow equipment such as blades, is enormous. A great number of these blades, with different mechanical properties, are available, but few studies have been made to facilitate their selection according to the optimum ratio of wear resistance to cost. To attain this objective, laboratory tests have been developed to correlate test results with those obtained from various road service conditions. The test materials, 1080steel in different states, 1090steel and D2 tool steel were chosen to cover a large range of hardness as well as different microstructures. Comparison of the wear resistance of the test materials relative to a standard revealed, in general, a good correlation between the results of laboratory cement wheel tests and those from the road tests. Scanning electron microscope wear scars of laboratory and road test specimens were compared to determine if similar removal material mechanisms were active. IntroductionThe correlation between wear tests in service and those performed with the aid of laboratory equipment is of considerable interest. As a matter of fact, when correlation exists, it allows one to evaluate the performance of a material more easily and at a lesser cost.Several authors have been interested in simulating various wear circumstances, especially abrasive wear. In particular, the simulation of wear on implements working the soil, has been tried by several researchers. The test using the rubber wheel seems to be the one giving the best correlation if the soil is rather sandy and its moisture content is low.However, little work has been done concerning wear on the plates, skids and blades attached to trucks used for levelling and snowplowing; such equipment being used to keep roads clear in northern countries. Now each year, companies introduce new steels by claiming that the y are superior in performance to their predecessor s and invariably they demand a higher cost. The study presented here was undertaken with the goal of making a more judicious choice of these steels by simulating their behaviour in the laboratory. Moreover, the examination of abraded surfaces in situ and in the laboratory have also allowed us to compare the respective wear mechanisms."

Jan 1, 1988

By Andrea M. Ouchi

A major focus of ground control research presently being conducted by the Geomechanics Group in the University of British Columbia Mining Engineering Department is to incorporate weak rock masses (RMR76 less than 50) into existing empirical design relationships. An emphasis is being placed upon the updated span design curve/critical span graph originally developed at UBC. The original database has been augmented by mapping of one mine in Montana and of several mines within the Carlin and Getchell Trends of Nevada. In addition, a neural network analysis has been performed and modifications of the span design curves at the lower RMR76 range have been made. The common factor in all the above mentioned mines is a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be dealt with to safely extract the mineral bearing rock. This work attempts to provide rock mechanic tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

May 1, 2004

By J. E. Nesset

"I had been requested earlier this year by MetSoc, our sister society of CIM, to contribute a chapter on technical developments in Canadian mineral processing over the past 50 years to their 50th Anniversary volume. Accepting the challenge of assembling such a chapter seemed at first a reasonably straightforward task, until one realises that the list of contributions by Canadians to mineral processing over this period has been more than just significant. It turns out to have been an extraordinarily fertile time for innovation and impact for Canadian-based technology. The list is necessarily a subjective one, however I had no trouble identifying twenty technology developments that are clearly outstanding, and there are undoubtedly others. As much as possible, I approached the individuals themselves who played key roles in each technology and asked that they tell the “story”. Without exception, all who were invited accepted eagerly and delivered more than I had hoped for. The technologies have been grouped into those that are truly Canadian innovations, such as the Knelson gravity concentrator and the McGill gas dispersion sensors in flotation, and technologies where Canadians and Canada played a very significant role in their success and implementation, such as AG/SAG grinding and ion-beam surface analysis. Also included are what may be termed technology transfer initiatives and institutions that have risen to a world class level, such as SGS Lakefield and the Canadian Mineral Processors Society of CIM. The challenge is now for the coming generation to continue this record of innovation and contribution to the industry, and that includes the (mostly) Canadian mining and metallurgical companies who have taken the longer term view and supported many of these initiatives, through their critical early years, with both financing and project sites for these ideas. Let us hope that the current trend of mining company globalization will not dampen their enthusiasm to participate. This plenary presentation will highlight many of these technologies, the individuals behind them, and their significance to the mineral processing industry."

Jan 1, 2012

PERSPECTIVE ?Natural resources exploration, extraction and beneficiation is complex and challenging: ?Input costs rising, complexity increasing, rising stakeholder management needs, regulatory compliance issue, etc. ?With increasing costs and complexity of managing operations are we simply getting less bang for our buck?

May 1, 2013

By J. D. Allan

"IntroductionThe purpose of this paper is to present a general picture of the Lynn Lake nickel area of northern Manitoba. The geology of the area will not be discussed in great detail, nor will the mining op; rations presently being conducted. Both subjects will be treated briefly and, in addition, mention will be made of some of the problems encountered in mapping in the area. some of the questions which still remain unanswered, methods of prospecting that have been applied and the future possibilities of the area.For present purposes, the Lynn Lake area will be considered as extending from west of Lynn lake to east of Barrington lake. Thus, more correctly, it should be termed the Lynn Lake-Barrington Lake area. It comprises five 15-minute map-areas, or a total of 800 square miles, in a block 47 miles east-west and 17 miles north-south.Lynn lake itself is about 120 miles north of Sherridon, Manitoba, the closes t rail terminal. The area is part of the Granville Lake sheet which was mapped by the Geological Survey of Canada in 1932, 1933, and 1935, the results being published in Summary Report 1933. Part C, and as Maps 343A and 344A on a scale of four miles to o.ne inch. In 1940, the McVeigh Lake area was mapped by the Geological Survey of Canada on a scale of 1,500 feet to 1 inch and a map was issued in 1945."

Jan 1, 1950

By Allen Chung, John Twomey, Christopher J. Greet

"It is widely accepted that the type of grinding media has an impact on the grinding chemistry and subsequent flotation behaviour of the sulphide minerals being separated. There are countless laboratory investigations demonstrating that inert grinding media produces more oxidising pulp potentials, reduced levels of grinding media corrosion products and superior concentrate grades and valuable metal recoveries. However, taking these results to industrial scale has proven difficult.Work conducted at the Ernest Henry Mine, in north western Queensland, Australia, at laboratory and pilot plant scale clearly indicated that using a high chrome grinding media resulted in significant improvements in both copper and gold recoveries. However, advancing this work to plant trial represented considerable financial and technical risk to the mine.This paper provides details of the protocol developed and used during the high chrome grinding media plant trial. It describes the test regime employed to measure changes in pulp chemistry, and the statistical methodology utilised to interpret the results. The work also highlighted the need for close cooperation between the metallurgists on site and the researchers conducting the trial.To date, the trial has produced excellent results: indicating that the copper recovery has improved by about 2 percent. The successful application of high chrome grinding media to the Ernest Henry ore has increased metal value by $18.7 million USD per annum based on current spot price for copper.INTRODUCTIONTheoryThe application of electrochemically inert grinding media to mineral systems has been extensively studied (Table 1). Broadly, these studies indicate that most sulphide minerals are more noble than the grinding media used during comminution. Therefore, the sulphide minerals are cathodic with respect to the forged steel grinding media, and the following reactions apply:"

Jan 1, 2011

By James Ransford Dankwah

High sulphur carbonaceous materials like petroleum coke and rubber tyre are unsuitable as reductants in ironmaking because part of the sulphur is transferred to the reduced metal. Globally, while large amounts of petroleum coke are produced annually from the industrial processing of crude oil, billions of end-of-life rubber tyres are held in landfills and stockpiles. This work therefore investigates the potential feasibility of utilising these high sulphur carbonaceous materials as reductants in ironmaking without transferring the sulphur into the reduced metal. Composite pellets of iron oxide containing end-of-life rubber tyre (RT), petroleum coke and blends of RT/petroleum coke and petroleum coke/high density polyethylene (HDPE) were heated under argon atmosphere in a horizontal tube furnace. Reduced pellets were analysed after 10 minutes of reduction for their sulphur content. The results showed that sulphur-free metallic iron can be successfully synthesized using RT and petroleum coke as reductants. The level of desulphurisation depends on the nature of blending of the carbonaceous materials.

Jan 1, 2014

By Tony Moore, Peter Riccio

"MMG (Minerals and Metals Group) operates the LXML Sepon’s mineral processing facility located 40 kilometers north of the town of Sepon, in the Savannakhet Province, Lao PDR. The Sepon copper plant produces 70,000 tons/year of LME grade A copper cathode using leachautoclave- SX/EW-flotation technology (Baxter et al., 2003). Pyrite recovery in the flotation circuit is critical to the operation, as it is used to generate acid and soluble ferric ion for the leach circuit. Low pyrite recovery has been an on-going challenge in the flotation circuit. Final tailings characterization work done by Ian Wark Research Institute (Bassell et al., 2006) showed that the pyrite losses to the tailings are made up of a combination of coarse liberated particles and finer particles that have been coated by clay fines.In December of 2005, a joint Cytec-MMG technical program was initiated to address the pyrite recovery issue. A series of diagnostic tests were performed in the Cytec Stamford Research Facility using synthetic plant water showing that the collector was precipitating as a metal salt and was unavailable for mineral attachment. The tests also identified several collector chemistries that would likely be robust in the low pH (< 1), high dissolved metal ion environment and will not complex with metal ions in solution. With the support of the Sepon on-site engineers, an extensive, successful laboratory program was completed, which was subsequently followed by on-plant testing that showed a step wise improvement in pyrite recovery.INTRODUCTIONLow pyrite recovery has been an ongoing problem in the flotation circuit at Sepon. Sulfur recovery (indirect measure of pyrite) was improved from 40% to 65%-75% in mid-2005 when on site laboratory work confirmed that AERO® 8045 Promoter was a more effective collector then AERO® 407 Promoter. However, sulfur recoveries above 65% could never be achieved. Sepon requested the Ian Wark Research Institute to complete a surface analysis study using Scanning Electron Microscopy, X-ray Photoelectron Spectroscopy, and Time-of-Flight Secondary Ion Mass Spectroscopy to determine if clay coated pyrite played a role. It was concluded that the pyrite losses to the tailings are made up of a combination of coarse (+ 100µm) liberated particles and finer (-74µm) particles that have been coated by clay fines. The majority of the losses appear to be due to the former. In December of 2005, a series of diagnostic tests were performed in Stamford using synthetic plant water in order to identify what chemistries would likely be robust in the slimy low pH and high dissolved metal ion solution environment. Results showed that several chemistries would not complex with ferric, ferrous or copper in solution and therefore should perform well in the Sepon flotation. The incumbent collector, AERO® 8045 Promoter was complexing with metal ions in solution. This resulted in the collector not being available for adsorption onto pyrite."

Jan 1, 2011

By Reno Pressacco

Abstract- Agrium Inc. is a world leader in the production, distribution, and marketing of agricultural products and services in both North America and Argentina. The new phosphate mine and mill complex located southwest of Kapuskasing, Ontario, was constructed to replace an offshore supply of phosphate rock, and produces a high-grade phosphate concentrate. The Cargill Township Carbonatite Complex is one of a series of carbonatite complexes in the region that are hosted by the 1.9 Ga aged Kapuskasing Structural Zone. The carbonatites in the mine area have intruded Archean gneissic granodiorite rocks of the Wawa Subprovince, and metasedimentary rocks of the Quetico Subprovince. The Cargill Carbonatite Complex displays a typical concentric zonation pattern from an outer ring of alkalic pyroxenites, through an inner ring of sövite-carbonatite, to a central core of rauhaugite-carbonatite. The initial carbonatite intrusion and subsequent residual orebody have been modified by faulting such that the northwestern third of the complex has been displaced approximately 2.5 km northeast. The phosphate ores are composed principally of residual apatite sands that were formed by the weathering and dissolution of the soluble minerals of the carbonatite protolith. These ores are subdivided by their iron content into high grade (A ores) and lower grade (B1 and B2) ores. They are separated from the primary unweathered carbonatite by a layer of saprolite, whose thickness varies depending upon the composition of the underlying carbonatite. Cretaceous waste materials consisting of well-sorted silica/kaolinite sand and peat deposits are typically found to stratigraphically overlie the ores. A minor amount of the ore feed comes from cemented phosphate ores. All rock types are covered by Pleistocene glacial tills and clays.

Jan 1, 2001

By V. Coffin, T. Cienski

"(Figure 1) Reagentized pulp enters into the column at about 1/4 of the distance from the top. Inside the column it meets with a downward flowing stream of water and with an upward flowing mass of air bubbles. Flotation takes place in this counter current system while at the same time fine gangue particles are washed off the froth before it reaches the overflow lip at the top of the column. The main operating features of the column flotation are as follows:a) No moving parts. Solids are kept in suspention not by an agitating action of a propeller but by settling down against the rising air bubbles.b) Wash water. Spray pipes are installed a few inches below the froth surface and deliver required volume of water. The purpose of this water is twofold:(i) it keeps in balance the flow of material through the column and(ii) it washes rising froth in the froth layer as well as removes unwanted fines attached to the bubbles at the lower flotation section. As a result the concentrate produced is of higher purity than in the conventional flotation. Column is characterized by very high up-grading. However, even temporary disruption of wash water supply results in a drastic drop of concentrate grate.c) Flow balance. (Figure 2) For the correct operation volume of the underflow (tail) is larger than that of the feed. The difference is made up by the wash water. This difference called bias is predetermined and ranges from some 4 to 15 USGPM depending on the size of the unit and process requirements."

Jan 1, 1981

By Barry D. Simmons

Abstract -A well-defined approach is essential to ensure the long-term success of a regional exploration program. Teck&apos;s approach in eastern Canada is designed to fulfill corporate objectives while recognizing certain unique parameters for exploration in the area. The elements of this approach include clearly defined objectives, technical considerations and personnel policies, all of which are equally important. The goal is a significant discovery before the mid-1990s and the company is confident that this target will be achieved.

Jan 1, 1992

"The Crescent, DM, and Pothook zones are copper-gold porphyry deposits which formed in association with alkalic intrusions of the early Jurassic Iron Mask batholith. The characteristics of the Crescent and DM deposits are nearly identical. Both formed along the contact between the Cherry Creek monzodiorite and Pothook diorite phases of the batholith. Permeable intrusion breccias along the contact concentrated the flow of hydrothermal fluids. Early, pre-ore alteration is represented by pervasive, sulphide-barren potassium metasomatism. The precipitation of copper-gold ore occurred during subsequent fracture-controlled potassic alteration, and is most strongly developed in chlorite-sulphide veins and their alteration envelopes. A central zone of potassic alteration is surrounded by a propylitic, pyritic halo in both deposits. The DM zone is unique among alkalic porphyry deposits in its high abundance of quartz-sulphide veins.The Pothook deposit formed at the westernmost contact of the Iron Mask batholith with enclosing Nicola Group volcanic rocks. Pervasive potassium metasomatism, similar in style to that at Crescent and DM, is associated with intrusion of the Cherry Creek monzonite. Pervasive and fracture-controlled albitic alteration is associated with intrusion of the Sugarloaf diorite and introduced minor copper-gold mineralization. Most of the copper-gold mineralization was introduced during formation of veins and breccia matrices dominated by magnetite/hematite and sulphide. Late-stage chlorite veining may have remobilized or introduced additional gold mineralization.Copper and gold assays in the Crescent deposit are well-correlated and have a nearly constant Cu:Au ratio, suggesting that the metals coprecipitated during a single hydrothermal event. In the Pothook deposit, copper and gold do not correlate closely, lack spatial correspondence, and suggest that transport and/or deposition of the two metals were not identically controlled and that they may have been introduced at different times by separate hydrothermal events."

Jan 1, 1995

By S. P. Singh

"The geological features of a rock mass have a direct influence on its blasting characteristics. It has been observed that perimeter control techniques provide excellent results in massive crystalline formations but may give poor results in weak and or highly jointed formations.A field study was conducted with the objective of understanding the role played by the geological features of a rock mass in producing and controlling blast damage. The field work involved the assessment of blast damage at several operating mines and the blasting of drift rounds in a geologically dominant rock mass.The effect of rock strength, rock quality designation (RQD), joint parameters and hydrogeological conditions on blast damage is described below. The influence of number and thickness of weak layers on blast damage is also discussed below on the basis of quantitative data. In addition, critical particle velocity ranges for damage to different rock types have also been outlined in this paper."

Jan 1, 2001

By J. E. Hawley

"The property of Francoeur Gold Mines, Limited, lies directly west of the Armfield mine in Beauchastel township, Abitibi district, and 12 miles west and slightly south of Noranda. The gold deposits are of particular interest because of their replacement character and close association with fault zones. The property was originally staked in 1923 following the discovery oi a mineralized zone near the eastern boundary. This became No. 1 orebody. Later discoveries in 1936 of No. 2 and No. 3 orebodies led to underground development and actual mining in July, 1938. A fourth orebody, No. 8, was found in 1939.The following is the production record up to December 31st, 1947:Beginning in September, 1944, ore was shipped to Noranda as siliceous flux, but late in 1946 milling of low-silica ore from No. 1 orebody was undertaken until operations were temporarily suspended in 1947.The four main ore deposits, Nos. 1, 2, 3, and 8, consist of siliceous ferrocarbonate and albite replacement bodies mineralized with fine pyrite and specularite in schistose fault zones in Keewatin volcanics. Barren to low grade quartz veins though present in some are uncommon, but small stringers of quartz are usually present wherever here and there visible gold is found. Nos. 1, 2, and 3 deposits lie in a major fault zone that extends completely across the property from west to east (over 7,000 feet) and dips N.40° to 50°, and are separated by intervals of 1,800 to 2,000 feet respectively. The fourth lies in a smaller fault zone striking east and dipping on the average 65°S.No. 1 orebody has been explored by mining to a depth of 500 feet, No. 2 to 400 feet, and No. 3 to slightly less than 300 feet . The greater part of No. 8 lies above a depth of 200 feet, but a raise has recently .been driven through from the west end of the 5th level of No. 1 to the 2nd level on No. 8 zone. Most of the ore of No. 8 zone above the 2nd level and of Nos. 2 and 3 above the 3rd levels has been removed."

Jan 1, 1954

By R. H. Wallis

Weighted moving-average contour maps have been constructed for molybdenum, copper and zinc using 7850 stream-sediment samples from 5430 square miles (14,063 sq. kms) of south-central British Columbia. Regional trends for molybdenum and zinc are northeast, north and northwest and those for copper are north and northwest. These trends are interrupted by zones markedly low in metals . The metal-rich trends cross rocks of different lithology and age and thus appear to be structurally controlled. The northeast trend may have exerted control on metal distribution at two different times.

Jan 1, 1978

By J. Chao, C. Tan, N. Stubina

"Since J978, Falconbridge Limited has operated two electric furnaces at its nickel-copper smelter in Sudbury. As part of its S02 Abatement Program, the smelter has undergone many changes over the last seven years.This paper describes the impact of these changes on the operation of the furnaces. Some of the topics to be covered include: the installation of sidewall copper coolers; current operating conditions; and furnace heat and mass balances. HistoricalFalconbridge began smelting ores in the Sudbury area in 1930. The original smelter consisted of a 1.3 m by 3 m blast furnace and two 4 m by 6 m converters. The blast furnace was supplied with untreated mine are and molten slag/matte was discharged into a round settler.In 1933 the smelter began treating flotation concentrates. The concentrates were mixed with fine magnetic ore and flue dust, then sintered on down-draught Dwight Lloyd machines. This provided an agglomerate suitable for furnace burden which was charged to the blast furnace while still hot.Between 1930 and 1954 nickel production was increased by lengthening the 3 m furnace to 4.6 m, then to 6 m, and later by constructing additional furnaces. By 1958, the plant consisted of one 7.5 m blast furnace, a settler, and three 4 m by 9 m converters."

Jan 1, 1994

By F. H. Samuel, P. Burke, F. Mucciardi, J. Gruzleski, S. A. Musmar

A new thermal analysis technique has been developed and tested. It utilizes the enhancement in heat transfer characteristics associated with a recent advancement in heat pipe technology. Heat is extracted from a liquid sample of a melt taken in-situ within a vessel or furnace. The rate of heat extraction is such as to cause the sample to solidify. The technique was tested in both laboratory scale and industrial scale (Grenville Castings, Perth, Ontario). A 356 Al Alloy, subjected to various melt treatments was used to perform the tests. Classical thermal analysis was also performed simultaneously using a preheated graphite cup and at the same melt conditions. The comparison showed the potential of the new technique over classical thermal analysis. The major advantages of the new method are that it conducts the analysis inside the melt (i.e. a physical sample is not removed from the melt), it consumes less time and the cooling rate can be precisely controlled during the solidification process. Moreover, the resolution of the results is better than that of conventional techniques. Aluminium

Jan 1, 2006