Search Documents

By S. Kelebek, B. Ingram, C. Gibson, T. MacNeil, M. Aghamirian

"The beneficiation and upgrading of pyrochlore from its ores is carried out through flotation. In industrial practice, upgrading is conducted in a two-stage flotation process in which pyrochlore flotation is carried out after gangue mineral pre-flotation (carbonate, silicate, sulphide or phosphate reverse flotation). In this study, the flotation of pyrochlore from a low grade carbonatite ore was performed at the laboratory scale following a two-stage flotation process in which carbonate minerals were floated in advance of niobium minerals. In parallel, a simplified flotation process was developed in which pyrochlore was floated directly from gangue minerals at increasingly acidic pH. Laboratory results indicated that both two-stage and direct flotation provided similar results in terms of niobium grade-recovery. Based on these results, a large scale, integrated pilot plant was conducted using a direct flotation flowsheet. While the elimination of reverse gangue flotation resulted in flowsheet simplification, the dissolution of carbonate minerals and the subsequent effect of dissolved cations on the floatability of pyrochlore added an element of complexity. A comparison of results from locked-cycle laboratory testing and pilot plant testing highlights the challenges of scaling up a complex flowsheet. A case is made for the direct flotation process and the key parameters to achieving success in large scale direct flotation of pyrochlore are discussed.INTRODUCTIONPyrochlore (Ca,Na)2Nb2O6(OH,F) is a niobium bearing mineral which has been the primary global source of niobium since the first pyrochlore mine commenced operations in the late 1960s (Gibson et al., 2015a). Preceding the discovery and development of high grade pyrochlore deposits in North and South America, the majority of global niobium supply came from gravity concentration operations of columbite (Fe,Mn)Nb2O6, across Africa (Perrault and Manker, 1981)."

Jan 1, 2016

The University of New South Wales (UNSW) has been a world leader in the development of innovative virtual reality technologies over the last 10 to 15 years. These developments have included developing the world?s first 360° surround, virtual reality (VR), stereo projection theatre system known as AVIE (Advanced Visualisation and Interactive Environment), which was developed by iCinema, a collaborative venture between the UNSW Faculties of Engineering and College of Fine Arts. The UNSW School of Mining Engineering has been responsible for development of mining applications virtual reality software modules and to date, has developed eighteen different mine safety training and mining engineering education modules which run in the AVIE environment. This platform and technology package provides a unique ?immersive environment? experience for groups of trainees or students who can engage with the simulated environment in the complete safety of the virtual reality theatre. In all of the major international mining industries, safety is of paramount importance, and training of personnel is an essential component of any comprehensive proactive safety management system. All personnel need to be aware of the inevitable hazards around them at all times, as well as understand appropriate safety and operational procedures. This can be done by conventional class-room style training sessions, or by provision of training documentation. However the effectiveness of such systems is often very limited due to the inability of trainers to engage with the audience for a lengthy period of time; or to convey the often complex and variable mining environments and situations which can exist in a typical mine. The ability to immerse the trainees in a virtual mine environment, with all the reality of an actual mine but with none of the physical exposure to actual hazards, provides a far more effective and engaging training experience. Furthermore, in the virtual world, trainees can be exposed to the very unlikely, but nevertheless high consequence hazards such as mine fires, falls of ground or outbursts, without any risk to their safety and well-being. The end result is that trainees will be far more engaged with the learning environment they find themselves in, and will develop a far higher level of understanding of the topics, rather than simply experiencing a passive class-room style learning environment offered by conventional training modes. The UNSW systems have been implemented widely within the Australian mining industry and the mining engineering education sector and are now being adopted internationally. This paper presents an overview of the innovative technologies involved in these virtual reality systems ? as applied to the mining industry. Modules developed for both mineworker training and mining engineering student learning will be presented, to illustrate the effectiveness and value of such a training and education approach.

Aug 1, 2013

By A. Darragh

"Past Growth The Canadian coal industry has grown rapidly during the past two decades. Coal production increased over four-fold between 1965 and 1982; consumption almost doubled, imports remained relatively flat, exports soared and total demand increased nearly two and a half times. Coal production grew during this period at an average rate of 8.60/o, compounded annually; this remarkable performance is shown in Table 1 and Figure 1. The relationship between production and consumption is shown in Figure 1, where in 1981 the total Canadian production of coal for the first time exceeded total Canadian consumption. ln Figure 2, the relationship between imports from the United States and Canadian coal exports is shown; in_ 1981 again for the first time, exports offshore exceeded imports into Canada. The rapid growth in Canadian coal use between 1965 and 1982 followed a major decline after World War II, as the country moved rapidly to an oil based economy. Changes in consumption patterns between 1945 and 1982 are shown ~n Table 2. Railway consumption of coal was reduced to zero m the early 1960s. The industrial and domestic consumers market share fell from about 660/o in 1960 to 6.70/o in 1975; this share, however, appears to have stabilized in recent years and actual volumes can be expected to increase in the future. The steel industry's share of the coal market fell over the same period, but the volume in recent years has remained fairly constant at about seven megatonnes per year.Perhaps the most significant change in consumption is in the share of coal consumed in the generation of electricity; this has increased from 80/o in 1960 to over three quarters of the total Canadian coal consumed in 1982. This increase in thermal coal consumption has been supplied by indigenous coal, and was accompanied by a decreasing share for coal imported from the U.S.A. into central Canada. It is expected, because of the nuclear power commitment in Ontario, that this share will continue to decrease, although the total volume of coal imported may increase slowly over time. This will likely also have a dampening effect on future coal sales to Ontario from western Canada."

Jan 1, 1985

By V. I. Lakshmanan

Rare earth elements and yttrium (REEs+Y) are being used in the making of hybrid electric cars, catalytic converters, wind power generators, LEDs, hard disc drives, flat panel displays, and portable electronics. Currently China produces more than 95% of REEs+Y, which has made REEs+Y a critical strategic resource. Process Research ORTECH Inc. (PRO) has developed the innovative mixed-chloride (HCl+MgCl2) solvent extraction processes for recovery of REEs+Y from their ores. The HCl leaching system provides the opportunity to regenerate the acid, while the presence of MgCl2 in the lixiviant enhances the activity of the hydrogen ion by orders of magnitude, making the lixiviant very aggressive and resulting in high recoveries of REEs+Y. Solvent extraction steps are used for separation and purification of REEs+Y from other value metals or impurities including iron, zirconium, hafnium, uranium, thorium, niobium, tantalum and titanium. Direct individual separation of REEs+Y in a mixed chloride system allows avoiding the additional process steps of precipitation and dissolution in HCl. The resulting process has a simplified flow sheet that is closed-loop and environmentally friendly.

Jan 1, 2014

By Shuan-cheng Gu

Roof bed separation often occurred due to the deformation incoordination of surrounding rock following the excavation of mine roadway. Bed separation has effect on the bolts, and the estimation of the influence will directly affect the safety of support systems. In this paper, the hyperbolic function model to analyze the load transfer mechanism on the bolts was simplified as the exponential function form for easy calculation. An elastic-plastic analysis model of the bolt loading occurred by the bed separation was established. And the development low that the bed separation affected to the bolt loading was discussed. According to the parameters analysis of different separation values and locations, the influence law of the bolt loading caused by roof bed separation was summarized. Finally, the effects of bed separation were considered for the bolting design, it was able to provide a reference to the anchorage design of stratified rock.

Aug 1, 2013

By Gordon Thompson

"Development of the unique Mine Games exhibition at Science World British Columbia is the largest ever collaboration of many interests to present the story of mining and the issues of mineral development delivered to the public by a science education centre.IntroductionMineral education programs have long been a major focus of the British Columbia mining community. Mine Games and its tremendous potential to enhance industries image and the public's awareness of mining is unequalled in the field of Issue Based Education Exhibits.The main goal of the exhibition is to look at the future of resource industries in a rapidly changing world of economic activities, new technologies, and growing public concern for the environment. Three challenges were the aim of the exhibition: to increase participation, to serve as a tool to increase interest in science and technology, and to draw an increasing number of school students to the interests of geology and the earth sciences. Mine Games is to serve as a meeting place for discussion of issues and where reliable information can be shared and new ideas explored.The exhibition is designed to develop new approaches to hands on learning that encourages visitors to explore and generate discussion and thinking with respect to resource development activities.The role of author, beginning in 1993, was, with senior industry leaders, to coordinate the raising of $1.3 million to complete the funding of the $1.6 million project total. The second and most interesting challenge was to work with the many minds that were collaborating to create the exhibition and to assure that the facts and science were correct. This involved the coordination of ""expert groups"" that verified the science and technology and the issues that the creative design team at Science World planned to use in development of each exhibit module."

Jan 1, 1995

By Nima Nabavi

Shovels and excavators have significant blind spots due to their large sizes, increasing the chances of collision with other surrounding equipment such as haul trucks, loaders, and dozers. While a camera surveillance system is very useful in preventing collision, it can benefit from two additional features: (i) the ability to display the distance of the closest object within the view, and more importantly (ii) the ability to warn the operator if objects are getting too close. After a comparison between few different technologies, it is explained how these features can be provided by integrating rugged pulsar radar sensors with a camera system. The specific radar technology is already field proven in the harsh mining environments. Motion Metrics International Corp. has developed this exact product, which combines its 4-camera surveillance system (ViewMetricsTM) with a series of rugged radar sensor elements, named ViewMetricsTM-Radar. The radar system employs intelligent CAN bus communication to reduce wiring, hence improving hardware reliability with built-in troubleshooting features. A USB connection is the only hardware bridge between the radar sensors and the embedded computer. As such, an existing ViewMetricsTM system can be easily upgraded to ViewMetricsTM-Radar. As addition of new interfaces to the cab could result in operator distraction, this paper explains how ViewMetricsTM-Radar reduces distraction compared to other radar collision prevention systems.

Oct 1, 2009

By William D. Macdonald

The Upper Devonian Kettle Point black shale of southern Ontario is poorly exposed. Structural maps pre-pared from the data of numerous wells show that the upper surface of the formation has low regular relief, and that the lower surface reflects domes in the Middle Devonian and also local subsidence of the Devonian rocks due to solution of salt in the Silurian Salina Formation. The appearance of minor amounts. of marcasite, pyrite, and calcite, m that order, as interpreted from the evidence of concretions from the type locality at Kettle Point is thought to have been influenced by a rise m the pH within anaerobic sediments preceding compaction.

Jan 1, 1960

By A. L. Mular, R. P. Edwards

"The operation of flotation circuits is often regarded as a combination of art and science. Expert systems offer a method by which the art may be captured and supervisory control of flotation circuits fully realized. Operating knowledge, the art, can be consistently employed to enhance regulatory control through the judicious application of an expert system. Using an expert system, a supervisory control routine was developed, and successfully implemented, in the copper flotation circuit at Brenda Mines Ltd.The expert system ran in conjunction with regulatory PI controllers on a personal computer. The expert system received assays via an on-stream analyzer and adjusted regulatory loop setpoints as required in real-time. From its commissioning in November 1989, to the end of the mine's operation in June, 1990, the ES was enthusiastically embraced by the operators and attained operating levels superior to those achievable manually.INTRODUCTIONExpert system (ES) software springs from research into artificial intelligence and is currently making significant inroads into business and industry. Proponents of ES's make many attractive claims; they are a means of capturing the knowledge of experts and they can be programmed by non-programmers. To date, most uses of this software in the process industry are in off-line applications, meaning that the applications are not tied directly to operating (on-line) environments. Moreover, in on-line environments, they are typically employed as advisors and only suggest changes. Human operators are required to close-the-loop to the process. Yet, ES's should be applicable to operating environments and, if the claims of the proponents are valid, should also be better than existing tools. As an intelligent controller an ES must use the knowledge of experienced operators, apply it directly to a process and do this without the intervention of human operators. On-line applications have been successfully employed in the closed loop control of SAG circuits (Herbst et al., 1989) and flotation circuits (Hales, 1989). Harris and Kosick (1988) detail an implementation for flotation control at the Polaris Mine."

Jan 1, 1991

By Jorge Amaya

A critical aspect of long-term open-pit mine planning consists in computing a production schedule based upon a block sequencing strategy. Such a schedule should specify when and if blocks should be extracted in such a way as to maximize NPV, while satisfying wall-slope and production capacity constraints. It is well known that this problem can be modeled with integer programming (IP). However, integer programming is not used in practice because the size of typical block models makes such problems intractable to standard IP solvers. In this article we describe a scalable IP-based methodology for solving very large (millions of blocks) instances of this problem. We show that embedding standard IP technologies in a local-search based algorithm we are able to obtain near-optimal solutions to large problems in reasonable time. This methodology has been tested in several mine wide block models.

Oct 1, 2009

By Jorge Amaya

A critical aspect of long-term open-pit mine planning consists in computing a production schedule based upon a block sequencing strategy. Such a schedule should specify when and if blocks should be extracted in such a way as to maximize NPV, while satisfying wall-slope and production capacity constraints. It is well known that this problem can be modeled with integer programming (IP). However, integer programming is not used in practice because the size of typical block models makes such problems intractable to standard IP solvers. In this article we describe a scalable IP-based methodology for solving very large (millions of blocks) instances of this problem. We show that embedding standard IP technologies in a local-search based algorithm we are able to obtain near-optimal solutions to large problems in reasonable time. This methodology has been tested in several mine wide block models.

Oct 1, 2009

By Frank Lemy

This paper presents an application of digital face mapping in an underground mine. Based on photographs it was possible to construct discontinuity maps, which were used to characterise the rock mass. The results were compared favourably with values obtained through scanline and area sampling mapping for the same site. The case is made for digital mapping as a safe, fast, and efficient way to characterise rock mass structure for engineering purposes.

May 1, 2001

By J. S. DeLury

The last few years have been eventful ones for Manitoba in connection with mineral development. Perhaps the past year has been the most important of all. It is therefore a suitable time to review the mining situation in the Province. In order to obtain, in the following paper, a proper set ting from which to discuss the trend of recent developments, a brief review of the story of mining will first be given. This will include a summary of a few of the outstanding facts regarding prospecting, discovery, and operations in the several known metalliferous areas of the Province. Following this will come a more detailed description of activities during the past year or two. Special attention will then be paid to the outstanding enterprises, such a~ those associated with the names of Flin Flon, Sherritt-Gordon, and Central Manitoba, names which have been attracting the attention of the mining world to Manitoba. And last of all will be presented a brief summary of mineral production, which, so far, has largely been credited to non-metallics. HISTORICAL To aid a proper comprehension of the recent trend in mining, it is well not to lose sight of the history of development in the different metalliferous areas in Manitoba. This Province seems throughout to have been more or less dependent on mining interest excited by discoveries in the neighbouring province of Ontario. The first interest came as an effect of the Lake of the Woods mining boom, when small adjacent parts of Manitoba were prospected. Several discoveries were made, but no mining industry resulted.

Jan 1, 1929

By A. H. Lang

"The great interest taken in uranium in Canada during the past few years has resulted in the discovery of a very large number of occurrences, and in much research that has added to the knowledge of the mineralogy and geology of uranium deposits. The object of this paper is to present that information in condensed form. Some of it has been published before, but the writer has been asked to bring it together and to add more recent, unpublished data. The paper therefore contains short accounts of the mineralogy of uranium and of the types and distribution of occurrences; brief regional descriptions, including information on some of the characteristic deposits; and conclusions regarding prospecting and development possibilities.The writer has access to much confidential information supplied in compliance with regulations of the Atomic Energy Control Board. He has used this only for making broad generalizations that could not affect individual interests, and only where the owners of properties have agreed to its use.Much of the information on mineralogy and geology is derived from the work of others. The writer is particularly indebted to M. H. Haycock and S. Kaiman of the Mines Branch; H. V. Ellsworth, S. C. Robinson, E. J. Brooker, H. R. Steacy, W. E. Hale, and A. M. Christie of the Geological Survey; and E.W. Nuffield, J. S. Stevenson, and other officers of provincial Departments of Mines. For information and many courtesies he is greatly indebted to so many officers of Eldorado. Mining and Refining (1944), Limited, and owners and staffs of private properties, that it is impossible to mention them individually."

Jan 1, 1950

By F. L. Pellet, S. Maiolino

"The determination of rock bolt contribution to reinforced joint shear strength is still a challenge, especially for assessing reinforced rock mass stability. For this purpose, several experimental studies have been performed during the last decades, mostly on small scale rock joint and bolt specimens. However, to accurately assess the rock bolt contribution, scale effect has to be accounted for. For this reason full scale lab tests are required as an alternative to in situ tests for which boundary conditions are more difficult to control.In this paper the results of an experimental program carried out with a large shear box, dedicated to test bolts in full scale conditions is presented. Different rock bolt diameters and different rock bolts inclination with respect to the shear plane were tested Experimental results were satisfactorily compared with an analytical model which is able to compute the contribution of the rock bolt to the shear strength of the joint as well the associated displacement of the joint. These conclusions allows us to validate the model in order to help the designer of reinforced rock engineering structures, such as slope or underground openings, to precise the optimum installation of rock bolts. INTRODUCTIONFully grouted rock bolts are commonly used for rock masses reinforcement to ensure the stability of rock slopes and underground cavities. For this purpose, the determination of rock bolt contribution to reinforced joint shear strength is of the utmost importance. During the last decades, several experimental studies have been performed to investigate the behavior of bolted rock joint. For obvious reasons, almost all the experiments were achieved on small scale bolted rock joint specimens (Bjurström, 1974; Azuar, 1977; Dight, 1983; Egger & Fernandes, 1983; Schubert, 1984; Spang & Egger, 1990; Egger & Zabuski, 1991). These studies made it possible to assess the influence of different parameters such as the bolt’s diameter, the number of bolts, the angle between the bolt and the joint, the nature of the rock, the friction and the dilatation angle of the joint. However, to accurately assess the rock bolt contribution, scale effect has to be accounted for (Vallier et al., 2010). For this reason full scale lab tests have been performed as an alternative to in situ test for which boundary conditions are more difficult to control."

Jan 1, 2015

By B. Damjanac, S. Maxwell, D. Chorney, M. Grob, F. Zhang, J. Hazzard

"A hybrid discrete-continuum numerical scheme is developed to study the behavior of hydraulic fractures crossing natural fractures. The fully coupled hybrid scheme utilizes a discrete element model for a core domain, within which the hydraulic fracture propagates and interacts with natural fractures, and a surrounding continuum domain to better approximate boundary effects. The results show that the behavior of hydraulic fractures crossing natural fractures is affected by a combination of factors. Nevertheless, three fundamental crossing scenarios can be identified from all of the simulations: no crossing, partial crossing, and direct crossing. Each crossing scenario has a distinct injection pressure history which may suggest guidelines for interpreting field hydraulic fracture injection data. Additionally, the capability for these models to generate synthetic microseismicity makes them appealing for the integration of microseismic field data with the reservoir geomechanics for ultimately providing a practical engineering tool for improvement of well completion and stimulation. The model is capable of examining and verifying four different shear deformation mechanisms associated with a propagating hydraulic fracture. The natural fracture can fail solely due to the stress perturbation of the passing hydraulic fracture or it can fail due to a combination of stress and pore pressure changes across different types of interaction scenarios. The simulations also illustrate that the level of fracturing complexity increases as the number and extent of the natural fractures increase. INTRODUCTIONAlthough hydraulic fracturing technique has been applied extensively as a reservoir stimulation technique in the oil and gas industry for over 60 years (Economides & Nolte, 2000), it is one of the key factors promoting the shale gas boom in the past decade (King, 2010; International Energy Agency, 2014). The hydraulic fracturing of shales can be differentiated from hydraulic fracturing of conventional reservoirs by the fact that shale formations often have a pre-existing discrete fracture networks which greatly impact the hydraulic fracture propagation. Based upon field production data as well as microseismic observations, it is believed that so called “fracture complexity” may result from interactions between a created hydraulic fracture and pre-existing natural fractures and planes of weakness (Warpinski, 2009; Maxwell & Cipolla, 2011)."

Jan 1, 2015

By Nader Golchinfar

The V-shaped breakout zones around excavation boundary have been captured by a variety of numerical methods such as FEM and DEM methods and failure criteria such as linear Mohr-Coulomb and non-linear Hoek-Brown failure criteria. Diederichs (2007) used Hoek-Brown parameters in his spalling parameter approach; however, it is convenient to use the Mohr-Coulomb failure criterion in numerical modeling because the material parameters can easily be determined from triaxial tests. It is shown in this study that when peak and residual strength parameters as well as dilation angle are properly defined, the brittle Mohr-Coulomb failure criterion can be used to model depth of failure near underground excavations satisfactorily.

Jun 1, 2012

By Matthew Blecha

The Tribag copper deposit is one of the rare examples of mineralized breccias in the Canadian Shield. The breccia is a pipe-like body, and consists of granitic, diabasic and volcanic fragments embedded in a vuggy, quartz-carbonate matrix. The mineralization is essentially chalcopyrite and pyrite, with minor molybdenite, sphalerite, galena and other sulphides. The main ore zone is saddle-like in shape, and is enveloped in a zone of chloritization, sericitization and clay-mineral alteration. It is suggested that the breccia is of the diatreme type. Introduction T HIS paper is based on eighteen months of field work, including surface and underground geological mapping and core logging, and on the survey of relevant literature. No significant amount of laboratory work has been done as yet. Location and Access The Tribag Batchawana property is located 40 miles north of Sault Ste. Marie, Ontario, about 10 miles east of Lake Superior. A 17-mile, all-weather road connects the property to the Trans-Canada highway to the south, and 4 miles of a 12-mile road remain to be completed to link it to the Algoma Central Railway to the northeast.

Jan 1, 1965

By A. Hashempour, D. Javani

"Selection of an optimal bit is a critical issue in drilling engineering. Specific energy (SE) and Cost per Foot (CPF) are the most common methods for evaluation of bit efficiency and optimal bit selection. The major shortfall of both methods is that they do not directly account for geological and geomechanical parameters of formations being drilling. In this paper, results of using the two foregoing methods are compared using Formation Drillability (FD) method, which directly accounts for geological and geomechanical parameters of a formation. This method combines various geological and geomechanical parameters and yields a dimensionless parameter indicating the formation drilling hardness (drillability). Results of this study show that the amount of energy, cost and time spent for drilling a unit volume / length of an identical formation may vary in different wells. This is due to the fact that geological and geomechanical characteristics of a formation may vary among wells and even within short intervals of a single well. Therefore, an optimal bit may not be appropriately selected, if drilling and economical parameters are the only factors considered and the formation geological and geomechanical specifications are ignored.INTRODUCTIONMany authors such as Bilgesu, Al-Rashidi, Aminian, and Ameri (2000) and Clegg (2006) conducted research in the evaluation of bit performance and optimum bit selection. Almost all of them tried to establish a good relationship based on geomechanical parameters. Primary examples are the research done by Ubaldi (1999), Macini, Magagni, Da Dalt, and Valente (2007)."

Jan 1, 2015

By Y. Champoux, N. Atalla, R. Oddo, C. Lesage

"Percussion drills are the source of the most serious noise problems in mining activities, due to their extremely high noise levels(114-122 dB(A)) and widespread use(Bartholomae and Stein, 1988). Percussion drills will continue to be widely used to drill small diameter holes in hard rock because no other method seems to be economically avail-able to replace them (Boillat et al., 1993).Many studies (Danière, 1991; Hawkes etal., 1977a; Jensen and Visnapuu, 1972;Leblond et al., 1976; Milette, 1989) were con-ducted to determine the major noise sources of percussion drills. The exhaust air of pneumatic drills, the hammer, the bit in contact with the rock and the drill rod have been identified as the major noise sources. A muffer can be used to reduce the exhaust noise and the hammer can be enclosed. The bit noise is considered to be of concern only at the beginning of holes. When all the available methods are used to reduce the noise of a percussion drill, the drill rod vibrations become the dominant noise source (Hawkes and Burks, 1979). However, the noise levels generated by this source remain high and future efforts should concentrate on reducing its radiation.Works by Hawkes and Burks (1979) and Hawkes et al. (1977b) for the U.S. Bureau of Mines provide the most complete description on the noise and vibration of percussion drill rods.The longitudinal and bending waves are the two most important types of elastic waves generated in drill rods. Among these, only the longitudinal waves contribute to the drilling rate. The bending waves are caused by non-centralized impacts, drill rod curvature and non-uniform bit/rock interface. Drill rod noise is generated by Poisson’s ratio expansions and contractions of the rod as the longitudinal waves travel up and down it and by transverse rod motions induced by bending waves. The radiation efficiency is much higher for bending waves than for longitudinal waves. Most of the impact energy is transformed into longitudinal waves, as expected for axial impacts. The evaluation of the relative contribution of longitudinal and bending waves to noise generation poses a very difficult problem for experimental, analytical and numerical approaches. It is, however, an important issue because the relative contribution of these two waves will guide future noise reduction efforts. It seems that very little can be done to reduce the noise radiation of the axial waves without affecting the drilling rate. The main difficulty that analytical and numerical approach-es face, in the evaluation of the relative contribution of the two waves, is that there is no adequate theory for predicting the bending vibrations from the factors that cause them. The experimental approach has, thus, been limited to test fixtures that do not adequately represent the boundary conditions, as well as by measurements obtained under real operating conditions from which it is difficult to establish the relative contribution of the two types of waves. For example, Hawkes and Burks (1979) and Hawkes et al. (1977b) used a test fixture with free-free boundary conditions and made no clear link with measurement under real operating conditions. Rather, they have based their discussion on a simple model. Many authors assume that fexural waves are the main noise source on drill rods. However, measurements have been somewhat contradictory and researchers are still unable to state with certainty that this is indeed the case (Lednik et al., 1988)."

Jan 1, 1997