Search Documents

By P. R. Stephenson

Mining projects depend on the amount and quality of the mineral reserves, which in turn depend on the amount and quality of the mineral resources. Only Measured and Indicated Resources may be converted to mineral reserves and Inferred Resources may not, with certain exceptions, be used in economic studies. Responsibility for the estimation of mineral resources rests with the Qualified Person (QP) and there is a wealth of literature, text books and case studies to guide the QP. Responsibility for the classification of the mineral resources also rests with the QP. While there is some industry guidance and common practice on approaches to resource classification on which the QP can draw, the process is (or should be) heavily dependent on the exercise of judgement by the QP. However, this inevitably leads to situations where, for example, one QP?s Inferred Resource is another QP?s Indicated Resource. If the QP?s judgement is poorly reasoned or illogical (as is sometimes the case), it can have a major impact on the project, often with substantial cost or value implications. Project managers and company executives should not unquestioningly accept QP?s classification decisions and should apply the same intensity of due diligence that they apply to other critical elements of the project.

May 1, 2011

By R. G. L. McCready, Marco Zentilli

"Brogan coal containing mean averages of 6,93% w/w total sulphur (1.1% sulphate sulphur, 1.6% organic sulphur and 4.24% pyritic sulphur) and 16.34% mineral ash was used as the test coal in these studies.Shake-culture leaching studies on seven size fractions of the coal, ranging in size from 0.045 mm to 1.7 mm, showed that the rate of pyrite leaching was inversely proportional to the particle size. As the use of continuous stirred tank reactors would be uneconomical for the reclamation of waste coal, column leaching studies were initiated on coal sieved to >6.35 mm to < 12.7 mm, The leachate was monitored for all metal ions and the release of iron was used to monitor the rate of pyrite oxidation . Measurable amounts of Zn, Co, Ni, Mn, and V, all of which can replace iron in the pyrite crystal structure, were released during the initial stages of leaching. Further, high concentrations of AI, Ca and Sr and trace amounts of Sn, As. Se, B, Ca, Cr, Si, and Ti were detected in the column effluents.These studies suggest that bacterial leaching will remove the pyrite and qualitative amounts of environmentally undesirable trace metals from the coal if such a process is developed for waste coal reclamation.IntroductionIn 1947, Colmer and Hinkle showed that acid mine drainage was the result of an oxidative attack of the iron-mineral sulphides by Thiobacillus ferrooxidans to produce sulphuric acid . Ashmead (1955) proposed the use of these organisms to desulphurize coal , but the subsequent research effort was concentrated on the metabolism and physiology of these extreme acidophiles.A limited number of studies have been reported on the bacterial leaching of pyrite from coal (Silverman et al., 1963; Dugan, 1977). However, the bacterial oxidation of pyrite is a self-limiting first-order reaction, probably due to the precipitation of Fe(OH)J and elemental sulphur , which progressively inhibits intimate contact between the bacterial cells and the sulphide-mineral surface. Consequently, the best pyrite oxidation experiments with coal reported to date required five days to remove 97070 of the pyrite (Dugan &Apel , 1978) using mixed cultures of T. ferrooxidans and T. thiooxidans."

Jan 1, 1985

By Fred C. Delabbio

The successful implementation of a new technology in an underground production mine requires many challenges to be overcome. These challenges include mine hardening of new technology, mitigation of safety risks and hazards, mine operation support, and technology transfer to mine staff. In the end, the majority of these challenges relate to the human aspects of implementation. The approach selected to overcome these challenges must be customized and appropriate for each unique situation. This paper outlines the approach used to address these challenges as part of successful implementation and resulting demonstration of the hydrogen fuel cell locomotive at the Placer Dome (CLA) Limited, Campbell Mine. This technology demonstration at Campbell Mine is critical for determining technical, regulatory and implementation aspects to be incorporated into future fuel cell prototypes such as the LHD project.

May 1, 2003

By G. Kollberg

"IntroductionThe SALA Caravan Mill system represents a proven concept for the design and operation of mobile and semi-mobile ore dressing plants.The Caravan Mill has been developed to meet the demand for a flexible processing plant to be used for small and medium-sized orebodies or for pilot investigations of deposits directly at the mine site e •The first Caravan Mill installation was put into operation in 1970 and a number of plants have been delivered world-wide since then.The Caravan Mill system has great flexibility both in capacity, ranging from 50 to 1000 tons per day, and in process combinations. The process modules available are:• crushing by jaw and cone crushers;• pre-concentration by the Dyna Whirl Pool dense media system;• grinding by wet rod or ball mills;• separation by gravity, magnetic, flotation or leaching-CVP adsorption methods;• dewatering by lamella or conventional thickeners and vacuum filters.To form complete plants, auxiliary equipment is also available, such as:• bins, feeders and conveying systems;• power generator units;• water tank and pump for process water;• interconnecting piping and cables;• erection and service tool kits;• set of spare and wear parts.For mine sites with rainy or winter conditions, a plastic tent with air heater can be supplied to cover the ore dressing equipment. Each module is workshop assembled complete with slurry pumps, internal pipe work, electric wiring with plug-in connections, hoses, etc., all arranged for quick and simple connection between the units. Before delivery, each unit is tested in the workshop."

Jan 1, 1982

By K. M. Sarkar

"In many plant trial s(1,2) it has been proven that very small amounts (10 to 20 ppm) of uranium dissolved in mine water can be effectively recovered by the use of ion exchange resins and this uranium recovery has many advantages. In this paper an economic analysis at different levels of uranium contamination and at different market prices of uranium are described.For this study an operating mine-mill complex with a sulphuric acid leach circuit, followed by solvent extraction (SX) process, is considered, where contaminated mine water is available in excess of process requirements. lt is further assumed that the sulphuric acid eluant containing uranium would be mixed with the mill pregnant liquor stream that proceeds to the SX plant for final uranium recovery.Recovery by Ion ExchangeMine water, in this study, is defined as the water coming from the underground mine, or mine pits, and the run-off water from stockpiles, mine shops, crushing plant , washdown areas, etc.In nature, uranium mainly occurs in two stages; reduced (tetravalent) and oxidized (hexavalent) . The oxidation of sulphides present in the orebody often causes the presence of S04- and acidity in mine water, and this acidic water readily dissolves U+6 part of the depo sit. The react ion between hexavalent uranium, which is dissolved in water as U02+ 2 cation and S04 producing uranyl sulph ate as,"

Jan 1, 1984

By G. T. Lapidus, J. Trejo-Gallardo

A phenomenological model is presented for leaching silver from silver sulfide contained in mineral particles with ammoniacal thiosulfate solutions of copper in stirred reactors. Experimental results were used to adjust the kinetic parameters of the model, such as the reaction order and velocity. The incorporation of the cuprous sulfide-silver sulfide equilibrium at the reaction interface allowed the prediction of the conversion limits for different reagent concentrations. The information obtained from the reactor model was later integrated into a heap leaching simulation, whose results adequately describe tendencies observed in column tests, with respect to variations in copper and thiosulfate concentrations. Comp

Jan 1, 2005

By Dougal R. McCreath, Dwayne D. Tannant, Peter K. Kaiser

The Geomechanics Research Centre at Laurentian University in Sudbury, Canada, has undertaken a five-year research program into the design of support appropriate for control-ling damage caused by rockbursts. Rockburst damage mechanisms in Canadian hardrock mines are reviewed and a support design approach is presented. Each element in a sup-port system performs a reinforcing, holding, or retaining function. The desirable load-displacement characteristics for elements in burst-resistant support systems are described, and recommended support systems are presented for a spectrum of rockburst conditions ranging from minor to severe. A support system can be designed to (a) prevent the triggering of aground fall or a rockburst; (b) deform to accommodate the large imposed deformations arising from a rockburst; or (c) absorb the kinetic energy contained in ejected blocks of rock.

Jan 1, 1996

By Jian-bin Xie, Lin-fang Shen, Zhi-liang Wang

"In order to research temperature field for construction of connecting passage in Metro using artificial freezing method, the finite difference software FLAC3D is employed to numerically simulate construction process of connecting passage. During construction, the overall distribution of temperature field around connecting passage, the relationship between soil temperature and freezing time, the distribution and variation for the thickness of freezing wall are studied from the perspective of numerical analysis. The results show as follows: after 55 days’ freezing, the soil temperature surrounding connecting passage is about -24 oC ~ -28 oC, and the minimum thickness of freezing wall is about 4.0m, which is larger than the design value 3.1m. So construction conditions have satisfied to the excavation of connecting passage and pumping station. During the excavation of connecting passage, soil temperature has almost no obvious change and the thickness of freezing wall remains constant mainly. After 45 days’ normal thawing, the temperature of freezing wall rises 12 oC approximately. And the soil temperature rises faster at the beginning of the normal thawing stage. In the whole process of construction, the frozen area is about 5m outside the edge of connecting passage, and the cooling area is about 10m outside the edge of connecting passage. INTRODUCTIONThe first recorded application of the artificial freezing method is on a mineshaft project in 1862, and it has been widely used in foundation pit engineering, subway tunnels, mine shaft engineering and so on (Wang Zhiliang, 2010; Zhang Juanxia, 2012; Qiu Fan, 2007; Zhou Xiaomin, 1999). This method has many advantages of enhancing soil strength; decreasing permeability and adopting various unstable soils (silt clay, sand, gravel, etc.). It has been applied successfully in metro engineering construction in Beijing, Shanghai and Nanjing. According to incomplete statistics, the construction of connecting passage using artificial freezing method accounted for 98% in Shanghai metro (Qiu Fan, 2007)."

Jan 1, 2015

By G. B. Harris

A new process for the recovery of copper and associated base metals from a polymetallic massive sulphide ore is described. The massive sulphide contains copper and especially nickel sulphide in a mineralogical form which negates both good recovery and high grades in concentrates using conventional flotation methods. Flotation concentrate processing and smelting from this ore is therefore probably not an economically viable option. Utilising the properties of high concentration chloride brines, a flow sheet has been developed and tested whereby the recovery of all of the metals and some of the power requirements for the plant itself can be derived from the ore. The new process overcomes the less-amenable-to-flotation ore characteristics, and provides the opportunity of economic processing in remote locations where the dependency on fossil fuels is both a logistical and an economic concern. The Ferguson Lake deposit of Starfield Resources in Nunavut, Canada, is the subject of this paper, which focuses on the leaching and copper recovery unit operations of the proposed flow sheet.

Jan 1, 2007

By J. Arzúa, L. R. Alejano, P. Rodríguez

"After six years of successful excavation with a support pattern, some roof failures have happened in a room-and-pillar underground mine excavated in a stratified rock mass. In this paper the authors give explanation to the failure mechanisms and redesign the support in order to solve the recent problems of roof collapse.The mine magnesite bed is approximately 14 m thick, and runs in the E-W direction with an average dip of 18º. Due to mine constraints and the inexpensiveness of the ore, the excavation is performed in the mineral itself, avoiding the need for mining dumps and waste excavation. Rooms and drifts are oriented in the mineral bed to form an angle of 19º to the direction of the strata, reducing the roadway gradients to less than 10%. Rooms are 11 m wide and pillars are 7 m wide. They are designed to leave a 1 meter thick magnesite bed in the roof of the rooms to act as a supporting beam. More often than not there is a layer of very poor quality marly shale up to 1 m thick resting on this magnesite beam. Overlying the poor quality marly shale there is a better quality, self-supporting sandy shale.First, a characterization of the involved rock masses (magnesite, marly shale and sandy shale) is performed, collecting the geotechnical data from previous studies and performing new in situ geotechnical surveys to check the soundness of the previous data. A distinction is made between different quality zones inside the mine by means of the RMR classification, associated to the occurrence of faults.Back-analysis of some of the failed rooms and data from exploration boreholes were used to determine the failure mechanisms (associated to Voussoir type failure or occurrence of sub-horizontal joints crossing the magnesite beam). Based on an understanding of these mechanisms, the method used to design the support and to analyse the stability of the different possible thicknesses of the magnesite beams of the rooms and drifts of the mine were improved.Numerical models of the most relevant conditions found in the mine were performed in order to better understand the behaviour of the roofs and to simulate the supporting solution obtained in the previous analyses.The most relevant conclusions with regard to the main elements causing the instability of the roof include the appearance of sub-horizontal discontinuities crossing the magnesite bed, which causes total instability of the roof and usually leads to collapse; excessive thinness of the magnesite beam in the problematic rooms; and the relaxation of the deepest (around 270 m in depth) zone of the mine because of existing faults."

Jan 1, 2015

By L. Bryson, J. H. W. M. Brits, K. Voogt

"The Anglo American Platinum’s Rustenburg Base Metals Refinery (RBMR) has the world’s first full deposit nickel plating tankhouse. Impurities in the nickel electrolyte can induce stresses in the electrowon nickel deposits that could lead to delamination of the deposit. Identifying the impurities that contribute to increasing internal stresses in the nickel deposit is key to successful operation and automation of the tankhouse. Impurities were introduced in the plant electrolyte and the effects on the full-scale nickel deposits evaluated. The impurity-adjusted electrolyte solutions were also analyzed using commercially available bench-scale methods to determine the induced stress. A correlation between impurity-induced deposit stress and full-scale delamination was developed. A direct correlation can now be made between feed quality, i.e. impurity concentrations, and degree of delamination in the plant. This methodology has the potential to rapidly predict the effect of new reagents, upstream process upset conditions and synergistic interactions between impurities on deposit stress and delamination of nickel deposits.INTRODUCTION Nickel electrowinning in sulphate media was first pioneered by Outokumpu in its Harjavalta refinery in 1960 (Saarinen and Seilo, 1985). The original process was very manual with starter sheets plated onto “acid resistant” steel for 36 hours and then manually stripped and cut into sheets which could be inserted into the main production cells for a further 4–5 days. The starter sheet stripping and manufacture process was later automated. The same technology was subsequently implemented on a number of plants around the world. Anglo American Platinum’s Base Metal Refinery (BMR) began nickel electrowinning in the early 1980’s. The recent expansion of Anglo American Platinum’s Base Metals Refinery necessitated the construction of a new nickel tankhouse to achieve two primary objectives. The first to increase the capacity to 32 400 tpa nickel and the second to reduce employee occupational exposure to nickel aerosols. The new tankhouse has been commissioned and is in the process of ramp-up; more details are given by Hagemann et al. (2016). Fundamental to lowering employee exposure to aerosols was automating both harvesting and final handling of cathode. In order to accomplish this a bold move was taken to plate up to 10 days on permanent titanium blanks which are harvested by automatic crane and automatically stripped. The original development work for the plating nickel on titanium blanks over a ten day cycle is given by Bryson et al. (2006)."

Jan 1, 2017

By Vahid Faghihi

SatraPM is a web-based software package, aiming to help project managers to easily handle their construction projects via internet. This software is capable of handling all projects of an organization, in which all projects can be defined in EPS the same as users in OBS. A 3D accessing module links EPS, OBS and inherent functions in order to provide a secure environment for the data to be processed throughout the system. This paper intends to take a deeper look at capabilities of SatraPM in helping project managers to keep track of and control their construction projects as well as its potential future features.

Aug 1, 2013

By S. Gößling-Reisemann

Most copper ores contain valuable co-products such as molybdenum, gold, silver, nickel, etc. Sulphuric acid and steam are valuable by-products, which are generated dur¬ing copper production. The environmental impacts from mining and refining therefore need to be shared between these by-products and co-products, an issue in Life Cycle As¬sessment (LCA) referred to as allocation. There are different, recognised methodologies for doing so: burdens can be allocated based on the market values of these commodities, they can be allocated by mass, volume, molar amount, functionality, or other physical, technical or economic factors. All of these methodologies have their respective merits and restrictions, and the choice is usually case specific. Nevertheless, the choice between alternative methodologies can have dramatic effects on the LCA results. Recycling in LCA has to be handled in a similar way, as it essentially constitutes a special case of co¬production. The existing standards (ISO 14040 ff.) allow different methods for imple¬menting recycling and allocation into metal LCAs (open loop, closed loop, value cor-rected substitution, etc.), which are still a subject of discussion in the scientific community. However, the methodology used can significantly influence the ecological profile of copper and copper products. We will present an overview of the different methodologies available for including recycling and allocation and give an analysis of how the meth¬odological choice affects the final LCA results. This work will be followed up by quantitative case studies.

Jan 1, 2007

By A. G. B. Hayes, C. L. Renzoni

"AbstractThis paper provides a rough outline of economic expectations for the near future and then goes on to discuss their effect on the expected demand for metals, using zinc, copper, nickel and aluminum as detailed examples.IntroductionMINING, as you are all painfully aware, is a cyclical business. We believe that it will remain so as long as there are economic cycles.The fortunes of the industry are tied to those sectors of the economy where decisions can be postponed until more favourable times: automobiles, housing, appliances, inventory building and capital spending. Over the past two years, while U.S. GNP fell by 3.8%, automobile production declined by 31 %, from 9.7 million units in 1973 to 6.7 million in 1975. Housing starts plummeted some 43% from 2.1 million units in 1973 to 1.2 million in 1975. Little wonder that U.S. copper consumption fell by 37% and zinc consumption by 38% over the same period.With the rest of the world's economies moving in unison with that of the United States, it is also not surprising that times have been tough for mining.Arthur Burns, chairman of the U.S. Federal Reserve, contends that each recession sows the seeds of its own recovery. The worse the recession, the better the subsequent recovery. If this is true, then the lot of the mining industry should improve significantly over the next two to three years."

Jan 1, 1977

By A. E. Flynn

THERE is at the present time a revived interest in amalgamation, due to the number of mines starting up, usually on high-grade ore, and utilizing this relatively cheap and convenient means of recovering gold, more especially in their initial stages of production. The marked increased use of the amalgamation process has revealed a dearth of amalgamators and there is no doubt the art of amalgamation has stood still for a generation or two and is not readily applicable to the modern practice of milling gold ores. Mill operators of long experience are learning the art for the first time and are giving it intelligent study, and considerable testing and research work is now being undertaken Most millmen consider amalgamation a simple process, and so it is when we have a clean ore with coarse gold, specially when stamps are used for crushing. In treating Nova Scotia ores by stamps and amalgamation, recoveries of 95 to 97 per cent are common and easily obtained. So-called &apos;under-water feed&apos; is almost universally used in Nova Scotia and is quite beneficial. The water is supplied through jets between the dies and below the die surface and maintains this space as a live trap which catches the gold particles before they are overground and spoilt for amalgamation. With this method, the portion of gold recovered in the battery is higher than usual and often amounts to 80 per cent of the total gold in the ore, the remaining 20 per cent being caught on the plate. As a continuous amalgamator, the simple plate cannot be excelled. Some of the modern devices having moving or covered and not very accessible plates, which cannot be readily inspected and dressed to keep them in condition, do not give the best results in service. An exception might be drawn in the case of amalgamation of very heavy ore or concentrate which would bank up unless the plate is carried at such a steep inclination as to weep mercury. Difficulties in stamp-mill amalgamation are encountered when acid water is used or when grease is present. Also, certain sulphides and graphitic and talcose ores give trouble, resulting in poor gold recovery and high mer-cury loss. The older literature on gold milling deals with the common troubles of this type and the old-time amalgamator was well able to take care of day-by-day difficulties. When the difficulties were unsurmountable, the ore was classed as &apos;refractory&apos; and other processes were used.

Jan 1, 1939

By Julian V. Simela

Conventional methods of underground surveying use theodolites/total stations and 3D laser scanners to obtain information about the underground environment. Current methods of geo-referencing these instruments to a mine reference system include triangulation, trilateration and resection. However, despite technological advancements, surveying procedures have remained slow, laborious and relatively unchanged during the last half-century. Recent innovations in the robotics community have shown that automated mapping of underground mining tunnels can be undertaken using 2D/3D laser scanners. These techniques have the potential to, in turn, improve upon current underground surveying and mapping methods. Automating surveying and mapping using current surveying tools without changing the setting up procedures or removing current constraints, or even changing the type of equipment used, does not change the status quo. The problem of moving from a static, tripod based surveying and mapping system to an unconstrained mobile surveying and mapping system is the subject of this paper. A current challenge for automated mapping is the ability to automatically geo-reference a mobile mapping system to a mine reference system. For a mobile mapping system that uses a horizontally mounted 2D laser scanner to gather data of the underground environment, the challenge of determining its position and orientation within the mine environment is magnified even more. This paper introduces Mobile Automated Scanner Triangulateration (MAST), a technique under development at Queen?s that is designed to geo-reference a mobile mapping system to a mine reference system for the purposes of underground mine surveying. MAST quickly and automatically determines scanner 2D position and orientation (azimuth) in a mine reference frame by using minimal human input.

Aug 1, 2013

By Simon D. Handelsman, Malcolm Scoble, Marcello Veiga

"Abstract - In many mining areas, potentially profitable mineral projects can be at risk because local people do not trust their governments and mining companies on many issues, including human rights. Projects will continue to be vulnerable to potential failure, delays, and higher costs. This paper suggests that geoscientists need to be aware of the global challenges they face from issues of corporate social responsibility, sustainable development, and human rights. These are not areas in which geoscience education has traditionally focused.This paper examines the types of conflict concerning human rights that are encountered by geoscientists involved in mineral exploration and development. It provides a background to human rights issues and presents a classification of the types of issue encountered. It reports on a survey of case studies that provide examples of the breadth, complexities, and consequences of such issues. The paper then concludes by outlining the development of codes and standards to improve performance, and suggests approaches for positive, practical engagement."

Jan 1, 2003

By R. Heikkilä

A large research and development program called RYM PRE (Process Re-Engineering) has been active in Finland since 2010. As a part of the program, a work packet Infra FINBIM is focused on the development of new national process model, specifications and requirements for the whole Finnish Infra Industry. In the Infra FINBIM, total 15 companies and main owners and 3 research organisations are included. The work is further continuing. The main achieved results up today have been the first specifications and requirements of the BIM based total process for infra sector, about 30 different pilot projects for testing of the new design and construction process models producing a lot of results and observations, a new open information transfer format Inframodel3 based on LandXML standard, the achieved acceptance of the Building SMART organization for support of international development, utilization and extension of the format within the whole infra industry, processes, software and other technical equipment. An evaluation of the results and this work will be drawn.

Aug 1, 2013

By Yongbao Zhu

The Ag2O-mediated reactions of cycloaurated compounds with a general formula Au(L)Cl2 (L = bi-dentate C?N ligand) with thiosalicylic acid, N-acetyl cysteine or 1,2-benzenedithiol in DMF proceeds via ligand substitution of the Au?Cl bonds to afford the S-O and S?S adducts all in good yields. The reactivity of the dichloro, S-O and S-S adducts towards thiols were examined by reacting with cysteine in an aqueous medium, revealing that all of Au-Cl, Au-O and Au-N are labile for thiol displacement. The measurement of the inhibitive activities of these compounds against human cathepsins B and K showed that the dichloro and S-O adducts are effective inhibitors with IC50 values ranging from 0.1 to 2.6 -M, and that the S-S adducts are inactive.

Oct 1, 2003

By M. H. Cullender

THE determination of the flow characteristics of gas wells depends upon the analysis of pressure data obtained under shut-in conditions and under one or more known flow conditions. These data are commonly referred to as back-pres-sure test data, and I know you are all familiar with the back-pressure equation where, Q rate of flow, Mcfd @ standard conditions C coefficient of the back-pres-sure curve P 1 formation pressure, psia P • sand face flowing pressure, psia P2 (psia)2/1000 n exponent of the back-pres-sure curve Figure 1 is a graphical presentation of the back-pressure equation; the coefficient is the rate of flow at a difference in squared pressures of 1, in this case 2250 Mcfd, and the exponent defines the manner in which the rate of flow changes with a change in the difference in squared pressures. In Figure 1, the exponent of the back-pressure curve is 0.554 which means that for a 10-fold change in the difference in squared pressures, there will be a 3.58-fold (10 raised to the 0.554 power) change in the rate of flow.

Jan 1, 1961