Search Documents

By G. V. Poropat

Roughness of a discontinuity may be an important factor influencing shear strength of the discontinuity. Traditionally, determining the roughness of a discontinuity surface and providing a numerical measure of the roughness has required considerable effort or specialised equipment. The development of new 3D imaging tools that are easy to use has provided effective fast and accurate means of creating 3D surface models from which roughness measurements can be readily obtained. These new techniques are versatile enabling a user to measure roughness along any desired profile and at any resolution up to the limit of the spatial subtense of a measurement on the discontinuity surface. This paper primarily reviews extensions to the use of 3D imaging that enable the measurement of roughness. Additionally we provide some examples of the measurements and examine some of the issues associated with extracting measures from the spatial data that will support estimation of shear strength.

May 1, 2009

By Q. Han, W. Dai

Al-Ti-B type master alloys have been widely used in the grain refinement of aluminum since 1940s. The introduction of Al3Ti and TiB2(AlB2) particles reduces the grain sizes down to about 200 micrometer level and makes cold work possible. However, the mechanism for the grain refinement is still not clear, though it is believed that TiB2 in the presence of Al3Ti nucleate a-Al grains in solidification. This paper presents our finding on the formation of (Ti,Al)B2 solid solution, which leads to a proposed theory on grain refinement by Al-Ti-B type master alloys that upon addition into aluminum melt stable TiB2 particles react with aluminum slowly and release titanium into the melt. The titanium thus released in combination with titanium in the melt through dissolution of Al3Ti maintains a transient titanium-rich layer on the surface of (Ti,Al)B2. This layer offers a low crystal mismatch with a- Al and promotes the nucleation of aluminum grains.

Jan 1, 2014

By A. J. Smethurst, S. B. Hearn, S. Boskovic

"The problem of crud in solvent extraction is well known and can be a major handicap and operational issue. Colloidal silica can cause a number of problems including interfering with flocculation, initiating crud formation in solvent extraction (SX), decreasing SX extraction kinetics and increasing SX phase disengagement times. Flocculation can be utilized to remove some of the troublesome particulates but colloidal silica does not flocculate well and presents a different problem requiring innovative chemistry to solve. Coagulants can assist by facilitating the removal of this colloidal silica by promoting the agglomeration of the particles to a size which can be more readily settled or flocculated in solid/liquid separations. This is achieved when the coagulants bind to the surfaces, displacing water and destabilizing the colloids, whereupon they bind to each other which facilitate their amenability to conventional flocculation.INTRODUCTIONSilicate minerals are abundant in the upper layers of the Earth’s crust, and there are few mineral deposits without significant levels of gangue silicates. Silicate minerals include the pure silicas, such as quartz and other silicate containing minerals such as clays, chlorites, feldspars, as well a vast number of less common silicates.During the acid leaching of ores, two types of fine silica particles are released in solution from the dissolution of the host mineral. The first consists of partly depleted silicates, and the second is colloidal silica, which forms in solution. It is this second type which has the potential to cause crud formation as well as poor solution clarities, slow filter rates and excessive flocculant usage (Figure1)."

Jan 1, 2016

In this paper we present the results of preliminary investigations into the applicability of new laboratory scale tests for the prediction of operating gap and specific throughput in high pressure grinding rolls (HPGR). The work is a part of the CAMIRO HPGR research program being conducted at the University of British Columbia, which aims to develop a suite of small-scale tests and procedures for the selection and sizing of HPGRs. A focus of the presented study is to test sample types in terms of their terra-mechanics based characteristics and relate them to specific throughput and gap results from pilot HPGR testing on the same samples.

Jan 1, 2012

By F. Romero

In the last four years, Compañia Minera Doña Ines de Collahuasi has been working in the application of advanced multivariate statistical techniques for the improvement of the metallurgical processes. In this paper the main conclusions for the application of multivariable analysis to the EW process are presented; including the identification of (target) process patterns according to throughput and quality criteria. Based on the process patterns, process variables hierarchies were identified by selecting the most influential ones, as well as to identify and isolate the root causes of pattern deviations and sub-standard operating conditions, cause-effect relationships were established, leading to the definition of process policies and controls to give early corrections to potential failures. The analysis was focused on cathode quality, specifically in its sulfur content, using an empirical model based on those variables that from a phenomenological and statistical stand point appeared to be the most influencing ones.

Jan 1, 2007

By Karen I. McMaster

"Abstract - The mining industry has endorsed the concept of sustainable development in principle. We now need to ensure that it is "lived" throughout the workplace. Frequently, sustainable development is viewed as just a policy and, more often than not, it is regarded as something that is applicable only to the areas of health and safety, environment, or community philanthropy. However, sustainability requires the collective action of an entire organization on a regular basis, a corporate culture where values are transformed into action.This paper reviews two of the many functional areas through which sustainable development can be pursued. Law and internal auditing are powerful means of instilling values, driving behavioral change, and improving performance. The development and role of each tool vis-a-vis sustainability is reviewed. Suggestions are offered regarding option and joint venture agreements, contract management programs, and various auditing programs based upon international standards and processes, market indices, and codes of conduct.The goal of this paper is to provide a general overview of these functional areas and to encourage further dialogue between employees and management in the workplace. It is hoped that others in the industry will examine the values of their companies, and review the ways in which individuals in all functional areas work, or want to work, on a daily basis. If we can harness collective commitment, creative thinking, and action in sustainable development, then the desired acceptance by stakeholders and improved financial performance will follow."

Jan 1, 2003

By Yu-Min Cheng

Over the past two years, the construction industry has increasingly recognized the benefits and capabilities of building information modeling (BIM) for information integration, visualization and parametric design, reducing the duplication of work and complexity of interface integration, while significantly saving both time and cost. However, due to the variety of participants in engineering projects, the differences between data definition, data format, and data storage increase the difficulty of integrating data from diverse sources. Therefore, buildingSMART has developed a common data schema, called Industry Foundation Classes (IFC), that makes it possible to hold and exchange relevant data between different software applications, to increase the efficiency of BIM work and to ensure a consistent and high-quality output. This paper presents a novel methodology that assists in facilitating the import and export process for parametric BIM objects between heterogeneous BIM systems. This methodology is based on the IFC data schema and includes graphical and non-graphical description data. The objective is to retain the geometry, parameters, unit, texture and links of an object during exchange and sharing to ensure that data integrity is maintained. To sum up, this research addresses the issues of transferring parametric BIM objects between heterogeneous systems to increase data integrity and reduce transfer and integration times.

Aug 1, 2013

By J. D. Bosman, L. J. Gardner

"The Bushveld Complex is a large layered igneous intrusion, located in the northern parts of the Republic of South Africa. The complex hosts the largest known reserves of Platinum Group Metals in the world. On the western limb of the complex, mining of the Merensky economic horizon and UG2 chromitite layer has been conducted for many years by several mining companies, including Impala Platinum Limited. Over the past decade, Impala has planned a new generation of greenfield vertical shafts, commencing with comprehensive geological and geotechnical studies. As part of the geotechnical studies, numerous tests have been conducted to quantify the mechanical properties of the various near-reef rock types. These tests include point load tests conducted in the field, as well as uni-axial compressive strength, triaxial compressive strength, and Brazilian disc tensile strength tests conducted in specialist laboratories. The authors have compiled an extensive database containing a large number of tests for different rock types, ranging from felsic Anorthosite to mafic Pegmatoid. The database was analysed to quantify the mechanical properties and values for Mohr Coulomb and Hoek Brown failure criteria for each rock type typically exposed by mining. The paper will provide a data set of rock mechanical properties typically used in numerical modelling and other design processes. Using the significant number of tests available, data describing the variability of the various parameters will be included."

Jan 1, 2015

By G. Archibald, M. McSaveney, J. Wartman, M. Yetton, C. Massey, C. Holden, A. Kaiser

"The 2010/11 Canterbury earthquakes triggered many mass movements in the Port Hills including rockfalls, rock and debris avalanches, slides and slumps and associated cliff-top cracking. The most abundant mass movements with the highest risk to people and buildings were rockfalls and rock/debris avalanches. Over 100 residential homes were impacted by landslides, leading to the evacuation of several hundred residents.Volumes of rock leaving several of the larger cliffs during the earthquake sequence were determined from terrestrial laser scan change models. There were no seismically instrumented cliff sites and there was some distance between the cliffs and nearest strong-motion sites. Therefore, we synthesised free-field rock-outcrop seismograms by employing a stochastic approach controlled by source models and regional parameters derived using spectral inversion of the extensive strong motion data set. Relationships between volumes leaving cliffs during the earthquakes and site peak ground acceleration (PGA), peak ground velocity (PGV) and Arias intensity were compared for different sites. Multiple linear regression was used to analyse the variables that best predict the volumes of debris that fell from the slopes during the main earthquakes. The best correlation between the volume of debris falling per square metre of slope face and the seismic forcing parameters was for vertical PGV. The results from the multiple linear regression incorporating slope height, inclination, PGV horizontal and PGV vertical, improved the statistical relationship.Field data and results from the 2D seismic site response assessment indicate that the following factors affect dynamic performance of the modelled cliffs: 1) cliff geology—mainly material modulus, shear strength and shear wave velocity; 2) slope geometry—ridge-scale versus site-scale effects; and 3) the temporal aspects of the earthquake shaking (i.e., single acceleration peaks of large amplitude versus multiple peaks of smaller amplitude). Model results show that amplification of shaking does not increase linearly with increasing height, but instead reflects changes in the cliff geology where material strength, modulus and shear-wave velocity contrasts lead to acceleration contrasts.These factors show that the use of well documented case histories provide the basis for more certainty in seismic landslide assessments compared to those that are only empirically based."

Jan 1, 2015

By T. Yalcin

"This paper describes a study carried out to determine the behaviour of Cu-Ni mill tailings during natural and flocculated sedimentations. Settling rates were examined under various conditions through standard laboratory batch settling tests. Flocculation was found to improve the sedimentation process significantly, but its effectiveness depended on several factors such as the pulp density of feed, the type and dosage of flocculating reagent, the pH of pulp, the intensity of mixing flocculant with tailings sand the use of stirring during compaction.It is shown that. for a sedimentation process taking place under given conditions, underflow pulp density (P) and sedimentation time (t) are related by the expression P = k.tn, where k and n are constants. A procedure is described for the use of this expression in thickener size estimations. IntroductionOften a considerable proportion of the mill feed is disposed as tailing, because the valuable mineral recovered usually forms a small fraction of the ore. Moreover, wet concentration processes result in liquid wastes that are several times more voluminous than the ore itself. Thus the handling and disposal of these wastes become an important cost item in most milling operations. The principal unit process employed in tailing disposal is solid-liquid separation which is traditionally carried out by gravity sedimentation in thickeners or tailing dams. Direct disposal of tailings into tailing dams is common practice where sufficiently large areas of land are available but it frequently becomes more economical or practical to densify the tailings in a thickener beforehand.Successful thickener operation depends essentially on correct thickener size which is in turn governed by the sedimentation characteristics of the tailings handled. Flocculation can aid the sedimentation process and bring about significant savings in thickener size, but its effective use requires a detailed study to identify the optimum conditions of application."

Jan 1, 1988

By J. Spross

"The Key Lake mill has operated since the fall of 1983. The ore from both Key Lake open pits will be depleted by 1997. It is planned to use this mill, located about 60 km southwest of McArthur, to process the McArthur River ore.While the geological data collected so far on the McArthur deposit are encouraging, more information of the deposit is needed before any detailed mine planning can begin.The surface drilling program identified the orebody and provided information on the geomechanical and hydrological properties of the overlying sandstone. It was proposed to conduct an underground exploration program to further delineate the orebody. This was air proved following a public hearing and review process. This program involves the sinking of a 630 metre deep shaft and the driving of one or two drifts along a portion of the orebody. From these drifts, exploration drilling every 10 m to 15 m through the orebody will provide the information required for the preparation of a feasibility study and an Environmental Impact Statement (EIS)."

Jan 1, 1994

"Real-time, on-stream analysis of the metal content of process slurries is an essential prerequisite for process monitoring and advanced control of mineral processing circuits. On-stream X-Ray Fluorescence (XRF) sensors for base metal applications are available commercially and form the basis of many plant monitoring circuits. To date, these commercial technologies have been insufficiently sensitive to measure precious metals such as gold and platinum group elements, typically present at part-per-million (ppm) and sub ppm levels. CSIRO has developed a novel X-ray based technology, called UltraGold, which enables detection of gold in slurries on a real-time basis with a precision below 100 parts-per-billion. This technology is based on the use of advanced X-ray optics, extensive Monte Carlo computer modelling for analyser design, high accuracy X-ray spectrum fitting where the X-ray intensities are matrix corrected. In this paper, we will introduce this technology and discuss the results of a proof of principle study performed in the laboratory with plant slurries (tailings and concentrate) from an Australian beneficiation plant. Finally, we will discuss further planned improvements. As projected grades in (gold) mining around the world fall and several large-scale mines approach the limits of their economic reserves, this method can enable significantly reduced operating costs by rapid analysis to improve circuit efficiency and hence improve recovery significantly.INTRODUCTION This paper describes a study undertaken to explore the feasibility of applying CSIRO?s UltraGold XRF technology to the on-stream measurement of gold in process slurries. The provision of rapid, accurate information of gold grade in feed, tailings and concentrate streams would facilitate significantly improved process control and early detection of plant upsets, resulting in substantial cost-savings. CSIRO have patented X-ray fluorescence (XRF) techniques for the analysis of key elements in slurries present at part-per-million (ppm) and sub-ppm levels. Conventional, commercially available on-stream XRF instruments generally have detection limits in the tens of ppm range, precluding their use for analysis of elements like gold that are mined and processed at much lower concentrations."

Jan 1, 2017

By Mauro Torres, Gabriel Zarate

"AngloAmerican used the extractant M5640 at Mantos Blancos and Mantoverde and uses PT5050MD at Los Bronces Division, which are aldoxime and modifier blends. In the first case, the modifier is the esther TXIB, while in the second case is the tridecanol TDA. It is a well-known fact that the extractant degrades while the modifier does not and with time the oxime/modifier ratio can change significantly, depending on the operating conditions of each plant.In order to evaluate the effect of this varying modifier content in the plant organic, especially in the organic losses, a complete metallurgical test work program was conducted at laboratory and pilot plant scale by Flomin SNF, a new extractant supplier. Results showed that the addition of an aldoxime without the modifier did not affect the chemical performance of the extractant, but there was a significant decrease in the viscosity and density of the organic.Based on the results obtained in the metallurgical program, it was decided to run plant scale tests at the SX plants of Mantos Blancos and Mantoverde. In these tests, instead of adding extractant to maintain the organic inventory, CuPROMEX 3406 which is an unmodified aldoxime was added until the original oxime/modifier ratio was reached. This was obtained after 6 months of operation and since then both plants are running with the extractant CuPROMEX 3302 both supplied by Flomin SNF.In the case of Los Bronces, the pilot plant work was completed and it is programmed to run similar plant scale tests. In this case, the oxime/modifier ratio increased and TDA will be added until reaching the original ratio.The plant results obtained at Mantoverde and Mantos Blancos, together with the pilot plant test results obtained at Los Bronces, are discussed in this paper."

Jan 1, 2016

By Adrian E. Scheidegger

"AbstractThe possibilities of deriving pertinent information about fractures in an oil pay from data obtained by core analysis are investigated. It is shown that it is possible to obtain an estimate of the fractured area per unit volume of the pay, and that the size of the fractures can be estimated if their shape is known. A suggestion of a routine procedure for the analysis of fractures is given.1.-IntroductionMany oil fields are producing essentially from cracks or fractures. Where this is the case, it is important to be able to obtain a knowledge of the size and distribution of those fractures in the oil pay. This knowledge has to be derived from the analysis of cores taken from the fields, as it is generally impossible to follow a fracture through the pay by direct means. The necessity of using statistical methods to extrapolate the meagre information obtained from the cores of the wells is therefore indicated.It is known that the fractures are much bigger than the diameter of the cores; thus, if they strike a core, the latter will generally fall into two pieces. The angle of the fracture with the vertical can be measured and, if oriented cores are taken, the exact position of the surface element representing the intersection of the fracture with the drill stem can be determined. Sometimes the edge of a fracture can be seen in a core. The number of •Cores that show such an edge can be noted. Of course, one has to be careful to distinguish between original fractures in the pay and fractures in the core caused by drilling operations. Only the former are relevant."

Jan 1, 1955

By H. Weissenbaeck, B. Nowak, M. Oesterreicher, R. Stastny

The producers of certain metals like nickel and cobalt increasingly face a shortage of easy-to-mine and easy-to-process ore bodies. Their focus is shifting towards alternative raw materials which in turn demand new, different extraction techniques. One potential route for processing a ferrous ore with a non-ferrous target metal is atmospheric leaching with hydrochloric acid followed by purification of the pregnant leach solution (PLS). For the separation of iron from the PLS, and, in turn, the extraction of the non-ferrous compounds, the following flow sheet is proposed. Pre-concentration of the PLS, oxidation of ferrous (if present) to ferric chloride, hydrolysis of ferric chloride leading to the precipitation of hematite and the evaporation of hydrochloric acid, followed by crystallization of non-hydrolysable metal chlorides by means of sparging hydrogen chloride into the solution. Hydrogen chloride required in the latter step is produced internally by super-azeotropic distillation of regenerated hydrochloric acid. The liquid filtrate from the crystallization step is recycled to hydrolysis. Depending on the specific composition of the PLS, the hematite produced contains only traces of other impurities, whereas the crystallized mix of non-hydrolysable metal chlorides – containing also the target metal in enriched form – contains ferric chloride only in an amount referring to the filter cake moisture. These crystals can then undergo further hydrometallurgical separation and extraction processes. As an example, this flow sheet is proposed for treating nickel laterite ores. Experiments related to the demonstration of crucial assumptions in the flow sheet are presented. Based on those experiments a mass and energy balance of the flow sheet was calculated and is presented here together with a table of the major consumables in order to provide a basis for an operating cost estimate and other process economics.

Jan 1, 2016

By Hung-Ming Chen

This paper presents a Cloud-based system framework for providing a web-based building information model (BIM) service. Cloud computing technologies were used to develop a BIM data center, which can handle the big data of massive BIMs using multiple servers in a distributed manner. In addition, the system allows multiple users to access the BIM data center online to submit and review BIMs concurrently. In this study, the advanced technologies/tools of web development and Cloud computing were applied and incorporated to develop a prototype system, named CloudBIM. On the client side, this study applied WebGL and HTML5 in the web-based interface development to achieve the 3D display of BIMs and the dynamic interaction with viewers through browsers. Users can access the services of CloudBIM by using PCs, laptops and tablets anytime anywhere to view the 3D model via browsers, which support WebGL. On the server side, this study used Apache Hadoop, an open-sourced distributed file system based on Google?s technologies, to establish a BIM data center. The Hadoop Distributed File System (HDFS) can utilize multiple servers to provide mass storage spaces in a distributed manner. Based on the use of Apache HBase, which provides Bigtable-like structured storage for HDFS, this study proposes database schema for storing the information from massive BIMs in two bigtables, named Object table and Property table respectively. In addition, Hadoop MapReduce, a Hadoop component for the parallel processing of large data sets, is utilized for model data acquisition by parsing the IFC files of uploaded models in parallel.

Aug 1, 2013

By K. Sakai, M. Miyaue, T. Aoki, T. Tani, S. Tanaka, N. Kudo

In the planning stage of a tunnel, due to limited technology in the geological survey and the financial restriction, tunnel supports are often designed from unsatisfactory information, and the tunnel construction is started. Therefore, "Information-oriented construction" is carried out in the construction stage, in which the design is rationally verified and modified by observations/measurements. Moreover, the ground conditions ahead of a tunnel face must be predicted for efficient and safe tunnel construction. The authors have examined effective prediction methods to the ground conditions ahead of a tunnel face under construction of mountain tunnels (Aoki et al., 2010) in view of the established method (Schubert et al., 1995). Though the prediction method of Schubert requires the displacement in the direction of tunnel axis, it is difficult to obtain its accurate data by the electronic distance meter. Then, we have proposed a method that uses tilt sensors installed at the tunnel crown near the face to obtain the slight tilting information. To measure inclination of the tunnel crown, this inclinometer was originally developed as a daily control measurement, such that the geological condition and its possible change behind the face could be detected early, and a steady advance and construction safety could be ensured. This paper describes the method of forward prediction mechanism and advantages of this suggested method. It then presents the typical results of a field verification test at a tunnel under construction and an example of evaluation of the ground conditions ahead of the face based on the 3D numerical analysis in three types of condition changes of ground deformation moduli.

Jan 1, 2015

By M. P. Amsden

"Ecstall Mining Limited, a subsidiary of Texasgulf, Inc., Operates the Kidd Creek Mine, Concentrator and Zinc Plant at Timmins, Ontario. Two different ore types are mined and milled to produce concentrates of copper, zinc, lead and tin. The ores are processed at the Concentrator in three separate individual milling circuits, each with the capacity to treat up to 3500 tons per day. Two circuits treat copper-zinc ore 1t an average combined rate of 6500 tons per day and the third circuit treats 3500 tons per day of silver-lead zinc ore. Conventional crushing, grinding and flotation procedures are followed. The purpose of this paper is to describe Ecstall's experience with rubber mill linings in the grinding circuits.CrushingBoth ores are crushed to minus 6 inches at the Mine and delivered by rail to the Concentrator where they are reduced by secondary and tertiary crushing to minus 5/8 inch.GrindingThe crushed ores are prepared for selective flotation by grinding with rod mills and two stages of ball milling. flotation circuit middling products are reground in regrind mills prior to further treatment. A typical flowsheet of one of the grinding circuits is shown in Figure 1.All the grinding units are Allis-Chalmers Mills. The rod mills are 10 1/2 feet diameter by 16 feet long. Both the primary and secondary ball mills are 12 feet diameter by 18 feet long and all regrind mills are 6 feet diameter by 12 feet long. The primary mills are charged with 1 13/16 inch forged balls. Secondary mills are charged with 1 1/2 inch forged balls and the regrind mills are charged with 1 inch forged balls. All cyclones are Kreb units. The primary cyclones are Dl5B hydrocyclones, the secondary cyclones are D6B hydrocyclones and all regrind cyclones are D6B hydrocyclones."

Jan 1, 1974

By Thomas Genty, Pascal Marcotte, Matthew Gillman, John Baechler

Elevated concentrations of ammonia nitrogen is a common characteristic of mine impacted water and generally results from the dissolution of undetonated explosives (i.e., Ammonium Nitrate and Fuel Oil and emulsion explosives) by contact water. Several active water treatment technologies are commercially available to remove ammonia nitrogen, but reduction of active treatment demand by promoting natural attenuation is considered best industry practice. In this paper, the results of laboratory-scale and full-scale trials of a semi-passive approach (i.e., enhanced algae growth) to remove ammonia nitrogen at the Meliadine mine are presented. Phosphorus was found to be the limiting factor to algae growth at the mine site. The addition of various concentrations of phosphorus was first tested at a laboratory scale. The samples were exposed to in-situ conditions, and ammonia nitrogen removal rates ranging from 40% to 93% were achieved over a period of 24 days. This paper also presents the methodology and results of an in-pond treatment during which a 50% ammonia nitrogen removal rate was observed after 68 days. The studied mine site uses breakpoint chlorination as its primary treatment approach for ammonia nitrogen removal. The results presented in this paper show the potential of using enhanced algae growth as a pre-treatment method, subsequently reducing the quantity of chemicals required for operating the breakpoint chlorination plant. This potential requires further investigation and additional trials are currently under evaluation.

Jan 1, 2023

By Masami Nakamoto

Controlled thermolysis of gold(I) thiolate complex, [C14H29(CH3)3N][Au(SC12H25)2], at 180 °C for 5 h under an N2 atmosphere produces novel gold nanoparticles passivated by alkyl groups derived from the precursor complex, the TEM photograph of which shows spherical particles with average diameter 26 nm. Since Brust et al. reported the two-phase reduction of AuCl4 - by NaBH4 to afford monodispersed gold nanoparticles passivated by alkanethiolate ligands (1), plenty of preparative investigations on gold nanoparticles (2,3) and its surface modification (3,4) have appeared, because of their potential applications in microelectronics (5). However, those preparative methods generally involve the reduction of AuCl4 - by reducing agent NaBH4 in the presence of suitable organic stabilizers such as alkanethiol (1-4), phosphane (5), quarternary ammonium salts (6), surfactants (7) or polymers (8). On the other hand, O?Brien et al. recently reported the preparation of organically capped gold nanoparticles at 190 °C, where tri-n-octylphosphine oxide and/or n-octadecylamine are used both as a reaction medium and as a passivating ligand (6), but this procedure also needs NaBH4 as reducing agent. Our strategy of novel preparative method of gold nanoparticles is the combination of reductive elimination of thiolate ligands and simultaneous attachment of organic moiety on the growing nuclei. Gold(I) thiolate complexes with ammonium cations were useful for our preparative method. We now report the controlled thermolysis of gold(I) thiolate complexes, [R(CH3)3N][Au(SC12H25)2] and [R(CH3)3N][Au(SC6H4-p-R?)2] (R= C14H29, C12H25; R?= C8H17, CH3), under an N2 atmosphere, where the powder of gold(I) thiolate complexes completely melts to afford the precursor liquid and then the liquid gradually decomposes. In spite of no use of reducing agent and solvent, reduction reaction is thermochemically induced to afford novel gold nanoparticles passivated by alkyl groups rather than by alkanethiolate ligands. Figure 1a shows a typical transmission electron microscopy (TEM) image of gold nanoparticles prepared by thermolysis of [C14H29(CH3)3N][Au(SC12H25)2] at 180 °C for 5 h, indicating a controlled growth of spherical gold nanoparticles. As shown in Fig. 1b, these spherical gold nanoparticles display the size distribution ranging from 5 to 50 nm. Although the particle size is larger than that of thiol-derivatized gold nanoparticles (less than 5 nm) prepared by NaBH4 reduction (1-3), the aggregation of gold nuclei is smoothly regulated and the growth of core gold is limited to be 26 nm in average diameter in spite of thermal procedure.

Oct 1, 2003