Search Documents

By Lawrence Melis

Fission Uranium Corp.’s Triple R Uranium Deposit at its Patterson Lake South Project is located in northwest Saskatchewan in Canada’s Athabasca Basin. As part of pre-feasibility studies for the project a detailed metallurgical test program was completed to provide process design criteria. The testwork program encompassed preparation and analysis of test composites, comminution testing, uranium acid leaching, liquid-solid separation, solvent extraction of uranium, precipitation of uranium yellowcake products, tailings and effluent treatment, tailings physical and chemical characterization, and environmental testing of prepared tailings, as well as investigations of gold and silver recovery from the mineralization. The paper provides mineralogical information, testwork methodologies and test results which were used to arrive at process design criteria and the selection of the process flowsheet for the project.

Jan 1, 2020

By L. C. Galloway, G. L. Tiley

"Mine hoist brakes must meet the following statutory performance criteria:- There should be two independent braking systems; at least one should act directly on the hoist drum.-If one brake fail s, the others should be able to retard and stop the hoist safely before the descending conveyance, carrying the rated load, reaches any obstruction.- When all brakes apply, decelerations should not be so violent that men travelling in the conveyance are injured.- The brakes shall not overheat and fade during an emergency stop.This paper discusses design principles and capacities of caliper and disc type brakes, when applied to double drum and friction hoists of equivalent capacity.IntroductionThis paper is about the brakes that are used on mine hoists; their functions, especially in emergencies, typical design, and how they are operated, controlled, tested, and adjusted.There are two basic types of mine hoists:1. Drum hoists, where the ropes are attached to, and coil on drums. The simplest system has only one drum. Most such hoists, however, have two drums, attached to a common shaft. Ropes are wound on each drum in opposite directions, so that when one conveyance is being raised, the other is lowered. The conveynaces may travel in vertical or inclined shafts. In the latter case, the hoist s are referred to as slope hoists.2. Friction hoist s, where the headropes are not attached to the wheel, but are in contact with it for an angle of lap of, typically, between 180 and 195 degree s. Forces are transmitted from the hoist wheel to the head ropes by friction.The lower ends of the conveyances are connected to balance ropes , approximately the same weight per foot as the headropes."

Jan 1, 1986

By Ralph L. Rutherford

Introduction During the past twenty-five years we have seen considerable exploration for oil on the plains of southern and east-central Alberta. This exploration has to some extent gone on in cycles, with periodic starts, stops, and occasionally some reversals. Each major attempt is usually supplemented by the application of some new method of exploration and, following each period of exploration, drilling tests are made. Whereas oil-bearing horizons are the ultimate objective of these explorations, the preliminary investigation frequently aims at a discovery of structure based on the long accepted belief that accumulations of oil and gas are to a marked degree structurally controlled. At the inception of this general exploration for oil, it was natural that attention should be directed to areas where there was surface evidence of deformation of the underlying strata, but, as the programme progressed, it was found that these surface manifestations of structure were often deceptive when attempts were made to project them to depth, to involve the deeper strata. Drilling of test wells was the only satisfactory method of obtaining exact information.

Jan 1, 1946

By D. R. Griffiths

"Oxidation of pyrrhotite prcxiuces sulphuric acid which in turn leaches out heavy metals, resulting in acidic contaminated seepages. The establishment of a marsh on top of the pyrrhotite would result in an anaerobic sediment, which should prevent further oxidation of the pyrrhotite. Initial data indicates that concentrations of sulphates and heavy metals in the seepage water are greatly reduced. Further hydrogeological studies are required however, to determine if metal and acidic loadings to the environment have increased.L'oxidation du sulfure de fer produit de l'acide sulfurique qui a son tour attaque les métaux ayant pour resultat une contamination d'acide et de métal des eaux d'infiltration. L'etablissement d'une couverture faite de boue et de vase au-dessus du depot du sulfure de fer réduit les effets de l'oxidation.Les données initiales indiquent que les concentrations de souffre et de métaux dans les eaux d'infiltration sent grandernent réduites.Des études plus poussées sent nécessaires pour déterminer si les quantités de souffre et de métaux dans les eaux d'infiltration ont augmentées.INTRODUCITONPyrrhotite tailings are readily oxidized through a combination of precipitation and atmospheric oxygen causing acidification of the unsaturated zone above the water table. This reaction is usually catalyzed by the bacteria, Thiobacillus ferooxidans. As the pH decreases, heavy metals become more soluble resulting in contaminated seepages to ground and surface waters.By creating a marshland on top of the pyrrhotite, an anaerobic intermediate layer should form between the organic covering and the tailings, preventing the oxidation process from progressing.In September 1986, Falconbridge Limited implemented a tailing reclamation project that involved creating a marshland on top of pyrrhotite tailings. The following paper will discuss and illustrate the preliminary results obtained during the sampling period of May to September 1987."

Jan 1, 1988

By Xiu-Xiang Tao

This study investigated bio-liquefaction of lignite and its model compounds of thymol, bezioc acid and quinoline by a fungus, Hypocrea lixii AH. It analyzed, during bio-liquefaction, enzyme activity of oxidase, LiP, Lac, MnP and polyphenol oxidase, and degradation products by UV-Vis, FTIR, 13C NMR and GC-MS. The results showed that the bio-liquefaction percentage (by mass) of lignite was up to 44.86 %. The bio-liquefaction products of lignite were mainly aniline, amide, ether, carboxylic acid ketone and ester. The aromatic ring number was 1-3 with an aromatic carbon ratio of 0.328, which indicated rings opening, bonds breaking and oxidation reaction. By considering with the enzyme activity analysis results, it showed that LiP and Lac catalyzed reactions to open aromatic cycles and to break bonds; esterase to break ester bond; and peroxidase in oxidation reaction.

Aug 1, 2013

By Ho-Sung Yoon, Jyothi Rajesh Kumar, Chul-Joo Kim, Sung-Don Kim

A recovery process for rare earths (REs) such as dysprosium and neodymium from the leach liquor of permanent magnet scrap (PMS) was developed. The two hydrometallurgical routes namely liquid-liquid extraction (solvent extraction) and selective stripping were implemented. The present study deals with the separation and recovery process development by using organo-phosphorous based extractant di-(2-ethylhexyl phosphoric acid (D2EHPA) as reagent for REs processing. Initial studies considered the influence of time on the extraction process, as well as pH and extractant concentration effects. This suggested the aqueous mechanism and separation factors played a role in process during development. McCabe-Thiele diagrams for extraction isotherms were developed. Counter current extraction (CCE) using various phase ratios influenced metals separation. Maximum loading capacity of the D2EHPA was determined. The loaded organic generated by the CCE process was water washed followed by a scrubbing process to remove the other metal ion from targeted metal. Finally, a stripping process was tested using various mineral acids.

Jan 1, 2015

By A. Gutiérrez

At present, most ore milling is done in tumbling mills, consisting of huge cylinders turning on their horizontal axis. This rotational motion causes the ore charge and the grinding balls to interact by impact, compression and abrasion, to reduce the size of the ore. This method is very inefficient since only around 12% of the energy supplied is used for actual grinding, the rest being used in moving the large mass of balls and ore within the mill. This work aimed at better understanding the milling process by evaluating the movement of the load through the Discrete Elements Method (DEM). First, the number of bodies (balls and ore) moving inside the mill is determined, to correlate to the potential impacts that constitute one of the milling mechanisms. Then, the number of high energy impacts is evaluated to correlate to the bodies in motion. At this stage, a differentiation between grinding media and the ore, as well as between the types of contact taking place in the mill, has to be made. This latter issue is of great relevance since from the five identified contact types (ball-ball, ball-liner, ore-ore, ball-ore and ore-liner) only the last three actually contribute to the milling process, the other two causing structural damage to the mill.

Jan 1, 2007

By Z. D’Amico

"IntroductionWE HAVE HEARD quite a lot recently on newer methods -of supporting roof, such as roof bolting or the use of metal props and •booms, but, with the exception of roof bolting, these methods are confined mostly to comparatively low, regular seams and even .bolting cannot be used to hold soft sides. Thus, where a seam of coal has great variations in thickness, or where it is faulty, or where the coal sides must be supported, nothing can wholly take the place of timbering with wood. This paper will deal mainly with the method of timbering such a seam, namely, the No. 3 seam mined by Brazeau Collieries, Limited, at Nordegg, Alberta, where the full height of a thick seam is mined in development. However, a few words on one or two other systems practised in Alberta when, in development work, a thick seam is only partially mined, should be of interest.Examples of Timbering in High SeamsThere .are several methods in use today for dealing with high seams of coal. The most popular is to develop the seam by driving road-ways in the coal by some conventional method, usually recovering the full thickness of the seam on the retreat. The following examples illustrate two variations of this method.In Figure I we have a thick •seam of friable coal, with a good roof, pitching about 30 degrees, which is being mined by taking the upper part of the seam in the development work, leaving the •bench coal in place. Figure 1A shows a section through a room."

Jan 1, 1954

By Gorzalczynski. Stan

The recent trend in underground mine developments is ?big is better?. This is most certainly evident in the mine shaft and the conveyances that operate within its compartments. Today, there are several new installations requiring mine cages that can transport up to 170 passengers. The technology in mine hoisting is advancing to address a combination of higher capacity requirements, deeper hoisting depths and faster winding rates, however, some areas of the hoist plant have not changed for the past fifty years. The most notable of these areas is the shaft compartment guide string and the conveyance mounted safety arrest mechanism. The technology in use today for the protection of passengers in a shaft conveyance from a hoist rope severance incident, remains conceptually unchanged from Elisha Otis? design of 1850. The actual retardation components, the safety dogs, have taken on several forms since Elisha?s invention with the last major design change occurring in the late 1940?s. The arrest of a free falling shaft conveyance requires that the shaft guides withstand the energy imparted on them by the safety dogs. There are some very real limitations presented by the use of wood for this application. The new hoisting era will most certainly continue to demand larger capacity equipment but also, an increased awareness toward safety.

May 1, 2002

By M. Kreuh

Crystalline Mg(OH)Cl and amorphous Mg2(OH)3C1 were successfully isolated from a hydrolyzed molten salt electrolyte sample in this work, It was found that the chemical form and crystallinity of the hydroxylchloride were controlled by the cooling rate of the molten sample when it was taken. Crystalline Mg(OH)Cl could only be obtained by cooling the molten electrolyte sample at a rate not faster than 0.6 °C/min, Upon more rapid cooling, the hydroxylchloride species precipitated as Mg2(OH)3Cl, The behavior of these solid hydroxylchlorides when contacted with fresh and non-hydrolyzed molten electrolyte at 550°C was also examined, It was found that the Mg(OH)Cl rapidly dissolved in the hot electrolyte and did not decompose into MgO at that temperature as would be expected from the literature, The dissolution rate of solid Mg2(OH)3Cl was found to be so slow by comparison that it resulted in the complete decomposition into MgO which thereafter was incorporated into the electrolyte as a suspended solid phase rather than dissolution.

Jan 1, 2004

By P. C. Parsons, G. C. Milligan

"IN FIELD WORK in the Cape Breton Highlands, which are heavily covered with vegetation, it is necessary to run traverses along the valleys of small brooks. We encountered difficulty in closing such traverses, and the following technique was developed to solve this problem. It has been tested in the field for four seasons by several people, and found to be simple, efficient and more accurate than any other compass-and-pace system of which we are aware. So far as we can find, the technique has not been described previously. It may be of use to others.The Cape Breton Highlands of Nova Scotia consist of hills of old intrusive and metamorphosed sedimentary rocks protruding up to 1,000 feet above the general level of the younger sediments which underlie the valleys. The flat hill-tops are the remnants of a plateau; drainage off the edge of this plateau has produced many small steep brooks. They occupy valleys which are up to 800 feet deep, and V-shaped in cross section, with steep sides covered by mixed conifers and hardwoods. The stream at the bottom is rarely more than a few feet wide, with a negligible meander belt, but with many bends, rapids and falls. Visibility along the stream, in consequence, is rarely more than a few hundred feet, and in many places much less.It was found impractical to map the streams by the method of meander lines, as described in many standard surveying texts and hand-books. The limited visibility, and the numerous bends of the brooks, necessitated many corners. Every corner introduces errors. To 'close' a survey with 40 or 50 such corners proved either very time-consuming or impossible. In most cases, however, the general direction of a valley may be obtained from an aerial photograph, or by direct observation, and this became the basis of the method adopted."

Jan 1, 1971

By D. G. Macintyre

Thick westward prograding clastic wedges were deposited along the margin of ancestral North America from Mid-Proterozoic to Mid-Paleozoic time. Periodic rifting and tectonic subsidence resulted in the formation of starved sub-basins along this otherwise passive continental margin. These sub-basins host important sedimentary exhalative barite-zinc-lead-silver deposits. In northeastern British Columbia, a thick succession of Paleozoic basinal facies clastic rocks is preserved within the northwest-trending Kechika Trough. Within the trough, sedimentary exhalative barite and barite-sulfide deposits occur in starved basin sediments of Middle Ordovician, Early Silurian, and Late Devonian age. The last are the most economically sigrrificant and are hosted by carbonaceous cherty argillites and siliceous shales of the Middle to Late Devonian Gunsteel Formation of the Lower Earn Group. The largest deposit, Cirque, has reserves in excess of 35 million tonnes averaging 100J0 (Pb +Zn) and 47 g/t Ag. Other potentially significant deposits include Driftpile Creek, Bear, Mt. Alcock, Fluke, Pie and Elf. Stratiform barite deposits are also common, particularly near the basin-to-shelf transition zone. The Late Devonian barite-sulfide deposits typically are zoned: interlarninated barite-sphalerite-galena-pyrite occurring near suspected vent areas grades outward into bedded barite. Laminated beds of pyrite typically occur in hangingwall siliceous shales, particularly above the inferred vent zone. The apparent absence of epigenetic stringer sulfide zones and footwall alteration implies that the deposits were formed from ponded brines at relatively low temperature. Away from the main deposits, the favourable stratigraphic interval is marked by the presence of thin beds of nodular and laminated barite and thin laminae of pyrite. Thin tuff beds also occur locally in this stratigraphic interval and are evidence for a Late Devonian volcanic event. A paleogeographic reconstruction of the Kechika Trough in Late Devonian to Mississippian time suggests that the barite-sulfide deposits formed in third-order starved basins between uplifted, northwest-trending horst blocks that were capped by shallow-water carbonate banks. The presence of intraformational breccias suggests that fault movement accompanied barite-sulfide precipitation. This tectonic activity may have allowed the escape of heated, overpressured metalliferous brines from permeable reservoirs within the sedimentary pile. Sedimentary exhalative deposits formed where these brines were exhaled as buoyant plumes onto the seafloor, cooled, and ponded in anoxic seafloor depressions.

Jan 1, 1992

By E. V. Manlapig, U. Erol, V. Ross, K. Tshimanga

Lonmin RoM ball mills are treating two types of feed ore produced by conventional mining and mechanised mining methods. It was reported that reduction in mill throughput was observed when treating the mechanised mining ore. Detailed grinding surveys were conducted for troubleshooting. Ore samples were collected for breakage characterisation using a JKRBT based on different particle density components. XRD analysis was conducted to investigate the association of minerals with density components. The plant surveys and the breakage characterisation tests all suggested that the two mining methods did not significantly affect either the ore breakage properties or the RoM mill performance. Instead, the mill discharge open area exerted a remarkable influence on mill throughput. The RoM ball mill operated at Lonmin K4 Concentrator has been proven to be a versatile mill that performed stably with variations in feed size distribution and feed ore changes by different mining techniques. The reasons are elucidated by the multi-component breakage characterisation and the plant surveys data.

Jan 1, 2012

By Liu Tao, Wang Wei, Liao Wenjiang, Yang Weiyan, Tang Bin

Side-blown Furnace technology is a developing technology and was developed very quickly in China in recent years, dozens of reference smelters can be found for the treatment of copper concentrate, copper slag, Lead slag, zinc leaching slag and different kinds of slurry. This paper introduces the working principle of the technology, displays the innovations and specifications of China Nerin's SBF technology, gives examples of the typical reference smelters, and looks ahead to future applications. INTRODUCTION Side-blowing furnace smelting process The side-blowing furnace smelting process (SBF process) is one of the bath smelting process with independent intellectual property rights of China Nerin. This process was originally applied to treat copper concentrate and high-lead slag. The SBF process includes two categories, i.e. to treat copper concentrate and to treat industrial solid waste. Up to now, the SBF process has been applied in around 5 million tons of copper concentrate processing capacity and 20+ plants with high-lead slag reduction process. In recent years, SBF process has been gradually used in zinc leaching slag, electroplating sludge, industrial solid waste (e.g., various metallurgical slag), and electronic waste disposal. The basic principle of SBF process is that the material to be treated is directly charged to bath through charging hole with crushed coal and flux, then, enriched oxygen air would be sent to slag level (Vanyukov/Jifeng style furnaces)or matte level (Baiyin style furnaces) via primary tuyere. In this case, the material completes matte/slag metallurgical reaction of gas-liquid-solid interaction under vigorous mixing, and separate matte and slag at the bottom of furnace hearth. With the help of secondary tuyere, the low-pressure air or enriched oxygen would be provided for secondary combustion in the freeboard. The core of SBF process is process parameter control and engineering design of SBF. Presented as a fixed rectangular type, the SBF is a metallurgical furnace consisting of copper water jackets and refractory material. The SBF is consisting of hearth, middle of furnace and furnace top with the sequence from bottom to top. The middle of furnace itself can be further divided into bath area and post-combustion area with primary tuyere and secondary tuyere at both sides. The furnace hearth is made of refractory bricks, which are fused and rebonded Mg-Cr brick, Mg-Cr brick and clay brick from inside to outside. The furnace top adopts a steel water jacket with charging hole and uptake shaft. The water-cooled partition wall is placed at uptake shaft and near charging hole.

Jan 1, 2019

By Haipeng Li, Jacob Masliyah, Barun Gorain, Jian Huang, Qingxia Liu, Zhenghe Xu, AuTec Innovative Extractive Solutions Ltd.

"Froth flotation is widely used to selectively separate one or more minerals from an ore over a wide range of particle sizes with high efficiency. Bubble–particle attachment is one of the most critical steps in flotation. The objective of this project is to demonstrate the need for an innovative dual bubble generator to improve flotation efficiency. This dual bubble generator was designed to generate two different sizes (micron size and typical flotation size) bubbles. The micron size bubbles generated on the crevices of particle surfaces in venturi type of cavitation tubes enhanced the attachment of fine particles to the bubbles in conventional flotation systems. They also acted as a secondary collector, which has the potential to reduce operation cost and improve flotation recovery. The dual bubble generator was evaluated for a double refractory gold ore with 3g/t Au, 1.5 wt% TCM (total carbonaceous matter) and 0.7 wt% sulfides. The results were compared with those obtained using a commercial bubble generator. Compared with the commercial bubble generator, the dual bubble generator showed not only a higher gold recovery, but also an improved separation efficiency, demonstrating the potential of dual bubble generator in fine particle flotation.INTRODUCTIONFroth flotation has been widely used in mineral processing and waste water treatment. However, flotation has been proven inefficient for fine particle recovery although it becomes increasingly inevitable to process fine particles with the depletion of easy processing ores. The critical problem of fine particle flotation is the low attachment of fine particles to flotation size bubbles due to their low collision rate. Based on a commonly acceptable flotation model given by R =F*[Pc*Pa*(1-Pd)], the probability of bubble–particle collision (Pc), attachment (Pa) and particles detachment from air bubbles (Pd) collectively determines fine particle recovery (R) (Yoon and Luttrell, 1986). Since Pc = (3Dp/Db) where Dp and Db are diameters of particles and bubbles, respectively, bubble size and particle size impact the bubble-particle collision in opposite directions. It is evident that the probability of bubble–particle collision decreases with decreasing the size of particles, leading to a low recovery of fine particles. In this case, reducing the bubble size and/or increasing the apparent size of particles by fine particle aggregation are clear means to improve fine particle recovery."

Jan 1, 2016

By Z. Trojanová

The deformation behaviour of ternary magnesium alloys AJ (Mg-Al-Sr) and AX (Mg-Al-Ca) were investigated in tension as well as compression tests. The samples were deformed at temperatures between 20 and 300 °C and at an initial strain rate of the order 10-4 s 1. The flow stress decreases with increasing temperature. The macroscopic work hardening rate decreases with increasing flow stress and temperature. The stress and temperature dependence of the work hardening rate is a result of the hardening and softening processes. Stress relaxation experiments were performed in order to reveal features of the thermally activated dislocation motion. Internal and effective stress components of the applied stress were estimated. A decrease in the internal stress was observed at elevated temperatures, which indicates recovery process (-es). A more detailed analysis of the estimated values of the activation volume and activation energy helped to interpret the thermally activated processes during plastic deformation. It is concluded that the deformation behaviour of the alloys depends on the activity of non-basal slip that is strongly influenced by temperature.

Jan 1, 2007

"One of the corporate values mentioned by many companies deals with respect for people. This paper discusses one aspect of this value, namely, the need for clarity of accountabilities and authorities. The job of the manager in achieving this goal is analyzed and the benefits of enhancing the manager-employee conversation outlined. IntroductionCorporate values usually refer to the standards of behaviour that the leaders of the organization expect of all employees, including themselves, in carrying out their duties. Terms such as integrity, respect for the individual, continuous improvement, continuous learning, teamwork, speed, and innovation are quite common. The company-specific values are typically developed by the top executives of the company, and then tested with a broader group of employees. Where the process works, employees have a good understanding of what behaviour is expected of them in doing their work, in making difficult decisions, and in interacting with others.Having spent considerable time in his career investigating and studying the management systems at over 50 of the most successful companies in Canada, the United States, Europe and Japan, the author has had the opportunity to visit organizations such as Hewlett-Packard, 3M, Xerox, Intel, Toyota, NEC, Komatsu, British Airways, and Eastman Chemical. These experiences, together with the work of many other researchers, including the work of Dr. Elliott Jacques, have helped significantly to form the thoughts expressed below.Rather than reviewing the creation of corporate values and their deployment through the organization, these remarks focus on issues over which managers and employees have some control. The value in which managers can have significant impact deals with people and the respect shown them in the workplace. The component of respect to be emphasized is to be clear about expectations or accountabilities for oneself and the people who report to you, and to ensure that personal authority matches those expectations."

Jan 1, 1999

By H. C. Gunnings, C. O. Swanson

"The Sullivan mine; at Kimberley in southeastern British Columbia; is the largest silver-lead-zinc mine in the Empire and one of the largest in the world.The original discovery was made in 1892 by four prospectors. Until 1899, when the branch line of the Canadian Pacific railway from Cranbrook to Kimberley was completed, little work was done on the property. In 1900, systematic development was started, and during the next 3 years 5,000 tons of ore was shipped to the smelters at Nelson and Trail. By 1903, some 300,000 tons of ore was developed, and a smelter was started at Marysville, about 5 miles from the mine. However, this smelter closed down in 1907 because of metallurgical difficulties after treating 75,000 tons, and the property came under the control of the American Smelting and Refining Company. An option on the property was taken in 1909 by the Consolidated Mining and Smelting Company of Canada, who exercised their option in the following year. During the next 5 years by selective mining and sorting 188,000 tons of high-grade ore was produced and shipped to Trail. This tonnage came from the upper levels, about 4,600 to 4,800 feet in elevation. At the same time, deep drilling down to the 3,900-foot level showed the presence of an immense body of complex ore. In 1915, the main adit-the 3,900-foot level-was started, and by 1919 this had been driven a distance of 2 miles to develop the ore above this level. Meanwhile, progress was being made in overcoming the milling problems. An interesting account of this work was written by the staff ( 4). In 1923, the first unit of the present concentrator was erected, with a capacity of 2,500 tons a day, and thereafter the rate of production increased rapidly. In 1934 it was around 8,000 tons a day, and to date a total of about 30,000,000 tons of ore has been sent to the mill. In recent years, a considerable part of the production has come from levels between the 3,900-and 3,350-foot, which were opened by an internal incline shaft started in, 1930. In 1942, tin was added to the products separated at the concentrator."

Jan 1, 1954

By V Dolmage

Copper Mountain is the third largest copper mine in British Columbia, and is now producing close to 20 million pounds of copper per year, with which is recovered also 4,000 ounces of gold and. 13,800 ounces of silver. After a long and checkered career, during which the ownership and management changed several times, this deposit finally came into the possession of the Granby Consolidated Mining, Smelting and Power Company in 1923. It was not, however, until the end of 1925 that the mine, under the management of Charles Bocking and C. H. Smith, was successfully placed on a basis of profitable production. It is a low-grade deposit of the contact-metamorphic type, with refractory ores consisting of chalcopyrite and bornite in a gangue of altered andesitic and basaltic breccia. The ore is concentrated to a product carrying over 30 percent copper, which is smelted in Tacoma. The deposit is 12 miles south of the town of Princeton, which is on the Kettle Valley railway, 150 miles east of Vancouver and 40 miles north of the International Boundary line. Princeton is served also by a branch of the Great Northern railway, which leads clown the Similkameen, Okanagan, and Columbia valleys. Copper Mountain mine and camp are connected to Princeton by a good mo tor road extending up Wolf Creek valley, while the haulage level of the mine, which emerges on the steep side of the Similkameen valley 1,000 feet below the camp, is connected with Princeton by a spur of the Kettle Valley railway leading up the Similkameen canyon and passing en route through Allenby, where the concentrator is situated.

Jan 1, 1929

By X. Cao, H. Huang, Z. Dai

"Crystal phase of copper-containing slag regulation by the slag viscosity, cooling speed and cooling method, where the slag viscosity is related to the temperature and alkalinity. According to the mineralogy properties of a copper-containing slag, experiments of crystal phase regulation and flotation were conducted. When the copper-containing slag that adding a small amount of calcium oxide was cooled slowly at a rate of 3°C/min and about 1050°C n a cinder inclusion system, the viscosity of slag can be remained under 0.25 Pa·S and more than ??% of copper particles that the grain size is larger than 20 ?m in slag. The whole flow of flotation experiment was carried out to recover copper from the copper-containing slag with crystal phase regulating and the copper concentrate grade was ?????%, the recovery efficiency of copper was 94.18%.INTRODUCTIONChina's annual output of copper slag is more than 6 million tons, the current total has reached 80 million tons. It is equivalent to 640 thousand tons of copper metal with the copper grade of 0.82%. Most of the smelting slag were storage. It is not only occupy the land and pollute the environment, but also make a huge waste of resource (Alp, Deveci, & Süngün, 2008; Carranza, Iglesias, Mazuelos, Romero, & Forcat, 2009; Gorai, & Jana, 2003), therefore, it is good way to achieve copper slag resources by the effective recovery of valuable component from copper smelting slag, which is an important measure of the current process of copper smelting slag and implement the central authorities to vigorously develop the circular economy, improve the recycling of resources, increase copper production of intensive development (Zhou, et al., 1994; Zhang, Zhang, & Wang, 2005). Currently, researches on comprehensive utilization of the coppercontaining slag made a much progress (Wei, 2004; Liu, Gai, Yang, Sui, Li, & Fu, 2008; Liu & Zhu, 2008; Zhang, 2010; Sun, Chen, & Tang, 2012; Qin, Wang, Ren, Wei, Peng, & Gu, 2012). Flotation is one of the most effective method to recover the copper from smelting slag, which has the features of low cost and high efficiency (Song & Liu, 2001; Zhang, Wang, & Li, 2012). But the copper particles in the copper smelting slag distribution is very uneven, and the thickness of the material is very serious. The copper content in the micro level is higher, the size of copper sulfide ore is less than 0.043 mm, which leads to the difficulty of the monomer dissociation (Tossavainen, Engstrom, Yang, Menad, Lidstrom, Larsson, & Bjorkman, 2007; Moustakas, Mavropoulos, Katsou, Haralambous, & Loizidou, 2012). In this study, according the process mineralogy of a smelting copper slag, the crystal of smelting copper slag was optimized by controlling the temperature, alkalinity, cooling rate and cooling method, which makes the fine copper mineral particles in the copper slag crystal further, and can be used to meet the particle size requirements of flotation, thereby enhancing the flotation of copper."

Jan 1, 2016