Search Documents

By R. Wang

"Under high stress conditions, rock bursts, borehole breakouts, and spalling events are common phenomena that occur around underground openings. In general, together these three phenomena represent brittle failures of an intact rock mass; however, individually they reflect different failure modes under high stresses. After analyzing and comparing the stress-to-strength criteria for rock bursts, borehole breakouts, and spalling events, proposed by previous researchers, it is found that these brittle failure phenomena share common stress-to-strength prerequisite. The stress-to-strength preconditions for brittle failures can be defined by the ratio of the maximum tangential stress around an underground opening to the uniaxial compressive strength (UCS) (s?max/sci) or by the ratio of the maximum far-field principal stress to the UCS (s1/sci). Both these indicators can be used to reflect the same stress preconditions. For s?max/sci, a ratio of 0.4±0.1 represents the critical stress requirement for brittle fracture. However, for s1/sci, a ratio of 0.15±0.05 should be considered as the critical stress requirement. Numerous engineering case studies and analysis of rock mechanics based on the Hoek-Brown criterion also verify these two stress-to-strength preconditions. Here, these two indicators are presented with an error range because complex rock mass quality ratings, lithology, and geotechnical conditions have profound impacts on the stress-to-strength preconditions for brittle failures. INTRODUCTIONHigh stresses are one of the most important factors that must be considered when undertaking underground rock mass projects (Kaiser et al., 1998). Wang et al. (2009) reviewed current progress in the evaluation of high stresses and their corresponding criteria. However, after clarifying the definition of high stress, civil engineers need to understand the deformation and failure behaviors of rock mass around an opening under high stresses. Under high stress conditions, the deformation of rock masses around an opening can be categorized into two groups, i.e., severe brittle failures (or rock bursts) and compressional plastic deformation of the surrounding rock mass, as indicated in Figure 1."

Jan 1, 2015

By Timothy W. Ellis

Gold-based materials have been a mainstay of the electronics and semiconductor industry since the physics was just a laboratory curiosity. Gold is the workhorse material in wire bond, flip chip and off wafer interconnections due to its corrosion resistance, ability to form metallurgical bonds by soldering or cold welding, and ease of fabrication. As the electronics and semiconductor industries grew, so did the use, of Gold in spite of the feature size reduction so elegantly demonstrated in Moore?s law. However, several revolutions in the Silicon miracle are threatening Gold?s place as the material of choice. Although cost is always an issue, the limitations are associated with the chemistry of Gold based alloys. Will Gold remain? Emerging requirements of bioelectronics, photonics and power requirements in conventional device represent new opportunities for Gold to shine. Additionally, as the world market demand for electronic, semiconducting, bio-electronic and photonic technology increases, given the right technology, Gold still can provide value proposition.

Oct 1, 2003

By L. Tejeda, J. R. Donald, R. Parra, J. Duran, P. H. Lauzon

"Crucible slag tests were employed to evaluate different refractory brick classes for the Cerro Matoso electric furnace. Comprehensive analysis was conducted to evaluate the crucible erosion and characterize any slag/refractory reaction products.The classes of refractories investigated were:•,tar-impregnated magnesia;•,rebonded fused grain magnesia-chrome;•,direct bonded magnesia-chrome;•,alumina-chrome;•,picrochromite; and•,magnesia-alumina (spinel).It was concluded that tar-impregnated MgO bricks were the most suitable for the slag chemistry and furnace environment according to corrosion and infiltration resistance. A picrochromite (MgCr2O4) brick performed exceptionally well with regards to erosion resistance, however, the slag infiltrated extensively through the brick pores. Alumina-chrome, direct bonded magnesia-chromite, and spinel (magnesia-alumina) bricks were evaluated as not suitable for use in the furnace."

Jan 1, 1999

By Nawshad Haque, Leanne Smith, Hal Aral, Joseph Cho, Warren Bruckard

"Water availability is one of the principal parameters in determining the feasibility of mining projects in arid and semi-arid regions. The volumetric water footprint (VWF) of a conceptual model of a copper flotation plant was found to be 2.45 kL/t Cu ore, compared with an actual measurement reported in the literature of 2.72 kL/t Cu ore. The flowsheet considered included mineral processing stages such as crushing, screening, grinding, classification, separation, flotation, thickening and filtration. The effect of a number of variables on the VWF was evaluated, including solid/liquid ratio, feed mass flowrate, ore loss, water loss, moisture content of ore, ore grade and water recycling. The use of seawater with recycling provided the most environmental and economic advantage among several scenarios evaluated. The study assumed a price of $1/kL freshwater, $4/kL for transport over a 200 km distance at 2,000 m altitude and $4/kL for water treatment. The water related cost of the desalinated seawater use scenario was A$493/t Cu concentrate, while the water related costs of fresh water and blended water scenarios were A$308/t and A$268/t Cu concentrate, respectively. The water related cost (fresh water scenario) accounted for 44% to 49% of the entire mining and processing costs that included drilling, blasting, loading, hauling, crushing, grinding and concentrating. The total overall cost was A$435/t Cu concentrate for the seawater with recycling, compared to A$451/t Cu concentrate for the fresh water with recycling case.INTRODUCTIONReducing the water footprint (WFP) by utilising alternative water sources has been a focus of mining projects due to increasing concerns about water scarcity and growing energy costs. The global mining industry can expect to experience fresh water shortages in the future, and saline or hyper-saline water may be the only available water source to process minerals in arid regions. Extensive studies on alternative water sources (e.g. seawater, desalinated seawater, blended water) and the reuse of process water have recently been conducted (Moreno, Aral, Cuevas, Monardes, Adaro, Norgate & Bruckard, 2011; Aral, Mead, Cuevas, Davey & Bruckard, 2010). Such studies provide sustainable and economic strategies for mines and concentrators in the arid or semi-arid regions of the world such as in Chile, Peru, Indonesia, and Portugal. More work, however, is needed to confirm water consumption data for different base metal flowsheets and use this data to develop water models that can lead to reduced WFPs and more sustainable water usage in the mining industry."

Jan 1, 2016

By James R. Kuipers

Center for Science in Public Participation CSP2 ? Organized in 1997 to provide technical assistance to public interest groups on mining and water quality issues ? 80%of effort devoted to direct support of grassroots groups and tribal governments ? 20% of effort devoted to public-oriented education for public, tribal, state and federal regulators, and for industry ? Board represented by public interest groups, at large citizens, and academia ? Professional staff with experience from mining industry, academia and government ? website: www.csp2.org CSP2 Mission Statement The CENTER for SCIENCE in PUBLIC PARTICIPATION provides training and technical advice to grassroots groups on water pollution and natural resource development issues, especially those related to mining. CSP2 seeks to focus the debate on factual issues, as brought to light by its technical analyses, and whenever possible to seek consensus and win-win solutions. CSP2 also performs policy related work with federal and state regulatory agencies on the implementation of water quality, waste disposal, and mining reclamation regulations.

May 1, 2002

By Marc C. Betournay, John E. Udd

"In this study, the authors investigated the stabilities of slopes cut predominantly into Trenton limestone in a large quarry in the Montreal region. Analyses of the bench and pit walls indicated that small-scale toppling, ravelling, and wedge failures are the most likely modes of instabilities. Because most of the joints dip steeply, however, the conclusion was made that relatively high walls could probably be justified.The field investigations were supplemented with the determinations of the shearing strengths of artificial discontinuities that were cut into samples of the limestone. The properties of a fine-grained limestone were found to be influenced very much by the magnitudes of the loads that were applied, while the properties of a crystalline limestone were found to be much less, or not load-dependent.The study is one of a number that are being conducted in this area.IntroductionExtensive quarrying has been done in the sedimentary strata of the Montreal area for a very long time. By any standards, it can be said that the Island of Montreal is a major mining area. At present, approximately 20 quarries are being operated in, or near, the city of Montreal.In addition to the millions of tons of limestone that are removed each year, a large number of excavations for foundations are cut into the sedimentary rocks.To date, however, very little information has been published concerning the engineering properties of the local geological materials. No mention is made of this aspect in the references which are presently available.Because of this lack of information, the senior author has initiated a study in which the strength properties of most of the rock types, and of the natural discontinuities contained in these, would be investigated. To date, the results of one other investigation have been published and other work is in process. It is hoped that the end result will be a comprehensive knowledge of the important strength properties of all of the rocks in the entire region."

Jan 1, 1983

By Jr. Wilkinson

Suncor Energy currently mines approximately nine hundred thousand tonnes of ore and waste per day at its open pit operations in the Athabasca Oilsands near Fort McMurray, Alberta. Modeling these deposits for planning purposes is particularly challenging given the characteristics associated with the deposit - stratigraphic deposition coupled with gradational grade distribution. The identification of ore and waste is a combination of bitumen cutoff grade, minimum mining thickness and separable waste thickness subject to criteria established by provincial regulatory agencies. Suncor along with Mincom Inc. have collaborated on this project to derive a methodology, automated by computer software, to streamline the ore and waste identification process. This paper explains the methodology and programs created to identify ore and waste in use at Suncor Energy and how this identification is used to categorize reserves and to generate mine design surfaces.

Apr 1, 2005

By Jürgen Kretschmann

The Islamic Republic of Iran is a very important producer of raw materials in the world. The country holds 68 types of minerals, including salt, sand and gravel, chrome, lead, zinc, copper, coal, gold, and iron-ore. With more than 37 billion tons of measured and indicated reserves and 55 billion tons of total mineral resources, Iran is ranked among the 15 major mineral-rich countries. Sangan iron-ore mines (SIOM) is one of the biggest iron ore mining complexes in Iran, located in a remote, but strategically important area near the Afghanistan border. The Iranian government has planned several mining projects in this region for a stepwise development over the next 5 years to satisfy the growing demand of the Iranian steel industry. In cooperation with private companies, these projects shall be realized as sustainable as possible. This paper introduces SIOM and describes socially responsible activities undertaken during the initial development of this mining complex. The effects of these activities will be demonstrated. Unique attributes of the Sangan area have a significant impact on the acceptance of SIOM by regional stakeholders. The government has made several social investments that benefit workers´ families and the community. They are attempts to build social capital for the mining operations and demonstrate a commitment for socially responsible mining to the communities and the local population. They aim to create a balance between the local and regional expectations and requirements and the necessity to secure the corporate profitability at a reasonable and sustainable level. Investment in socially responsible activities is not a choice but a necessity to improve the relations between mining companies and stakeholders in the communities. It is recommended that social investments should be carefully planned and implemented from the early stages of mining activities, and should proceed throughout the life cycle of the mines.

Aug 1, 2013

By L. Dufourm

This paper presents a review of plant layout considerations incorporated into recent designs of SAG/Ball mill circuits for two medium sized concentrators. The plant layouts presented and the design concepts discussed, relate to smaller SAG circuits, but can equally apply to larger milling circuits. Included are design concepts and ideas introduced by the various project teams, and the focus is on the primary factors of any layout design which are safety, constructability, operability, and capital cost.

Jan 1, 2012

By B. E. Halbert, K. T. Himbeault, S. L. Fernandes, R. L. J. Phillips, B. J. Topp

The Beaverlodge uranium mining and milling facilities operated from 1952 to 1981 with about 94% of the ore extracted from the main underground mine and 6% from smaller satellite deposits. Decommissioning work occurred from 1982 to 1985 involving periods of shutdown, salvage and reclamation. Transition phase monitoring, leading to eventual delicencing commenced in July 1985. Over the last 15 years, discharge from the tailings management facility (TMF) and a fresh water stream, impacted during the operational phase by tailings spills, has improved in water quality for most parameters of concern. Loadings to the environment of three key contaminants (radium-226, total dissolved solids, and uranium) have consistently been less than during the operational phase with radium-226 having the greatest variability. Outstanding environmental issues associated with the recovering drainage system formerly used for tailings disposal, are being addressed in an enhanced environmental monitoring program to commence in 2000. Changes in water chemistry and the natural re-introduction of aquatic organisms are issues of concern. In the meantime, application for release from selected satellite areas commenced in 1999. This paper reviews the issues which have arisen during the transition phase, outlines how they have and are being addressed, and provides a comparison of original and current predictions of the recovery process under way at the former Beaverlodge mine site.

Jan 1, 2000

By F. Sorenson, P. A. Castellarini, F. Garbarino, M. N. Garcia

"Recently, significant efforts to improve productivity from the tight intervals of the Mulichinco Formation within the Sierra Chata Field in the Neuquén Basin have been ongoing. Because conventional high quality reservoirs were being developed in this field, a proper reservoir understanding and completion approach was applied. After developing these high permeability reservoirs, the operator began evaluating the tight intervals and new areas within the field, but a completely different approach was necessary to achieve motivating production improvement.An extensive study to help enhance reservoir understanding and identify key factors controlling productivity of these tight intervals (which tend to be in the range of 5 µD) has been ongoing. Some of the issues discussed in this study are 1) petrophysical review, 2) rock properties calibration, 3) geomechanics understanding, 4) faulting and micro faulting/lineaments description, 5) stimulation and completions review and, 6) understanding key production drivers.As in many other tight reservoir projects, a considerable area of the reservoir must be effectively stimulated during the hydraulic fracturing process to achieve economic productivity. Two critical issues hinder these objectives. First, the low permeability in addition to a pore pressure close to or even lower than hydrostatic are critical characteristics when attempting to flow back the well and clean up fractures. Second, very high horizontal stress anisotropy resulting from a strike slip stress regime promotes the generation of simple planar bi-wing fractures. It is well-known that this fracture geometry will contact much less reservoir area compared to more complex fractures, as the operator would normally intend to create at very low permeability reservoirs.This paper discusses these issues and how they were addressed. A pilot drilling and completion program was initiated during 2012 to validate this study. Key factors include well location relative to formation unconformities, their orientation relative to the far field principal stresses, hydraulic fractures generated, and overall completion design."

Jan 1, 2015

By Osvaldo A. Bascur

Business Challenges ? Many Versions of the Truth ? Lack of Enterprise Visibility (Transparency) ? Limited Communication & Collaboration ? Complex Implementation & Maintenance of software ? End user ease of use of information applications ? Responsive to change ? Access to timely information ? Secure computing ? Maturing Workforce Real time Portal - First of All ? Why Move to a Portal - Portals Recaptures the Business User - Broader Scope - Easy Navigation, World Standard - Features of a Portal - User Profile - Delegation (Secure Delegation of Admin Authority e.g. portal\pat) - Single Sign-On ? HUGE

May 1, 2004

By J. A. Morgan, P. M. Dimmell

Abstract - The Aubry pegmatites are located on the Seymour Lake property, 15 km north of Lake Nipigon in northwestern Ontario. The property lies within the Caribou Lake-Marshall Lake greenstone belt along the English River-Wabigoon subprovince boundary of the Superior province of the Canadian Shield. The property was optioned in March 2001 by Linear Resources (now Linear Gold Corp.), who carried out gridding, prospecting, geological mapping, soil and lithogeochemical sampling, trenching, channel sampling, and a total of 1,866 m of diamond drilling in 32 holes. The Aubry pegmatites are classified by Breaks et al. (2003) as complex type, spodumene-subtype, lithium-cesium-tantalum pegmatites (Cerný, 1989). These pegmatites generally form under high-pressure-low-temperature conditions, display complex internal zoning, have relatively low Nb/Ta ratios in the ore-forming assemblages, and contain significantly elevated tantalum values (Cerný, 1989). Other examples of spodumene-subtype pegmatites include the formerly producing Hugo pegmatite in South Dakota, and the currently producing Greenbushes pegmatite in Australia. The Aubry pegmatites occur as an undulating system of stacked sheets that dip moderately to steeply eastward over a 1-km strike length. The main portion of the North Aubry pegmatite ranges in true thickness from 10 to 28 m over a strike length of 125 m, whereas the thickest portion of the South Aubry has an estimated true thickness of 15 to 16 m over a minimum strike length of 95 m. The North Aubry pegmatite remains open downdip and along strike to the north, whereas the South Aubry pegmatite remains open downdip and along strike in both directions. The Aubry pegmatites are among the most highly evolved in Ontario, with the southern end of the North Aubry (trench 5/6 area) being the most highly fractionated (Breaks et al., 2002). Channel samples from the trench NA-5 area of the North Aubry pegmatite produced values up to 2.49 wt.% Ta2O5 over 4 m. Coarse manganotantalite crystals, up to 5 cm in diameter, from this trench contain up to 84.9 wt.% Ta2O5 (Breaks et al., 2002). Drill hole SL02-31 in the trench NA-6 area gave values of 0.046 wt.% Ta2O5 over 17.7 m, including 1 m @ 0.464 wt.% Ta2O5. Further exploration will focus on defining the grade of the North Aubry zone, extending and defining both known pegmatites, and identifying additional Ta-rich zones within them. Lithogeochemical and enzyme leach soil geochemical data suggest the presence of multiple undiscovered pegmatites on the property.

Jan 1, 2005

By Marc Tardif

"The way alarm information is provided to an operator can make a huge difference in the minutes following an upset. Process alarms are often looked at as a way to help avoid catastrophic failure and serious accidents. But knowing that mineral processing is so energy consuming and that raw material is not consistent, all small upsets should also be seen as a catastrophe because they can have significant impact on product cost and quality.This paper will demonstrate how it is possible to use data from process alarms to provide operators with real time, value added information that will help them take the right decision at the right time and in turn, reduce unplanned downtime by 20 to 80% and incidents by up to 50% (number and cost),and optimize energy and capacity usage.In the era of Big Data, living in a world where we are submerged with information, one of the biggest challenges is to find the right information at the right time.Alarm rationalization projects will often focus on alarm quantity, but alarm quality is also very important. It is possible, by following a simple 6-step process to turn “alarms” into truly valuable information for operators. Based on known standards (ANSI/ISA 18.2 and EEMUA 191), this process will capture the knowledge of the best and most experienced operators and process engineers, and make it readily available to everyone, right on time, when it matters the most.INTRODUCTIONWhen spending some time in a modern control room, it is easy to notice the huge quantity of information that is available to the operator. Modern operation stations feature multiple screens with HD capability. These screens display information like process display, history trends, alarms and events list, maps with geo-located information, images from live cameras, etc. However, it is harder to assess whether all this information is really helping operators: Is all the information relevant? Are process screens overcrowded? Is the information easy to understand? Does the operator know what to do with all the information? Are there too many alarms?"

Jan 1, 2016

By A. T. Jakubick, A. MacG. Robertson

This paper reviews key issues related to the placement of dry (soil) covers on extremely weak, compressible fine tailings. The design and construction of soil covers on such tailings often presents a formidable challenge to the geotechnical as well as the environmental engineer due to the low shear strength, poor traffic ability, and high settlement of under consolidated tailings at the time of reclamation. The geotechnical issues to be considered include: (1) consolidation of near-surface tailings to achieve strength gains, improve traffic ability, and allow safe placement of initial cover layer; (2) stability of tailings slopes during dewatering of tailings ponds and/or cover placement; and (3) long-term settlement of tailings and its impact on cover integrity and final surface shaping. The environmental issues to be considered include: (1) management of contaminated (free) pond water; (2) management of contaminated pore water expelled during tailings consolidation; and (3) management of (uncontaminated) surface water on top of the cover. This paper summarizes recent experiences gained in a large uranium tailings reclamation project. It is concluded that a careful consideration of both geotechnical and environmental issues during the planning stages greatly reduces the costs and environmental risks associated with fine tailings reclamation.

Jan 1, 2000

By Engineering Staff

"This paper briefly describes the surface mining operations at Smoky River Coal Limited (formerly McIntyre Mines Limited, Coal Division) near Grande Cache, Alberta. Geology, mining methods, equipment, manpower and reclamation and environment topics are discussed. Introduction Smoky River Coal Limited, a wholly-owned subsidiary of McIntyre Mines Limited of Calgary, Alberta, produces a high quality, low sulphur, low volatile bituminous coking coal from its minesite located at west central Alberta, approximately 20 km from the town of Grande Cache and 360 km west of Edmonton (Fig. I). Most of the coal property is contained within a 30 km long by 20 km wide block lying in a northwest-southeast direction in mountainous terrain. Elevations vary from 920 m above sea level ·at the plant·site on the Smoky River to 1,600 mat the upper levels of current and proposed mining operations. A total of 11 coal seams have been identified. Only two seams, No. 4 Seam and No. 10 Seam are currently considered of major commercial value. These seams are recovered by both surface and underground mining. Approximately 650Jo of the plant feed coal is obtained from a conventional shovel/truck surface mine; the balance is mined underground by room-andpillar methods. Background In 1921, McIntyre Mines Limited acquired some 26,300 hectares of coal leases at Smoky River. Since then the leases were explored intermittently by different companies including McIntyre. In the mid-l 960s exploration activities increased and several feasibility studies were completed. Development of the area was undertaken by McIntyre in 1968 and, in August of the same year, a long-term contract was signed with a consortium of Japanese steel mills for delivery of 2 x 106 t of clean coking coal for 15 years commencing in 1970. Production was focussed on underground mining, using longwall methods."

Jan 1, 1985

By J. T. Chen, S. Winkler, M. J. Worswick, O. Orlov

This paper presents a review of research conducted at the University of Waterloo concerned with the application of aluminum alloy sheet and tube in automotive structures and body panels. The research has focussed on formability prediction and results using a range of damage-based formulations. These models include continuum-level damage approaches and, more recently, a so-called percolation damage approach intended to capture microstructural heterogeneity effects on damage development. This paper presents applications of these damage approaches to simulate formability of experiments considering stretch flange panels. The experiments consider drawbead effects associated with the bend/unbend deformation as the material flows through the drawbead. Recent work on simulating in situ X-ray tomography experiments that capture damage evolution during tensile deformation will also be reviewed.

Jan 1, 2006

The Silvermines area of north County Tipperary in Ireland has experienced mining activity for over a thousand years, with lead, zinc, copper, barite and sulphur being extracted from a series of Carboniferous limestones. The last mine to operate in the area was closed in 1993. A legacy of contamination and derelict surface structures remain. Following the death of cattle in the vicinity in 1999, a governmental Inter-Agency Group was established to conduct an investigation. The ?Silvermines Rehabilitation Project? resulted, and included a proposal for the development of a Mine Waste Management Facility (MWMF) to act as a repository for waste materials from problematic sites across the area. The nature of the setting supported an effective solution from both a cost and performance perspective; and with limited maintenance requirements. Locating the MWMF where most wastes were identified would help minimise handling and relocation of materials. This position coincided with an area of artesian groundwater pressures. The resulting MWMF design consisted of a perimeter engineered embankment with the crest elevation designed to just exceed the groundwater piezometric surface. The base would remain unlined and groundwater permitted to rise up into and saturate the contained in-situ tailings deposits and imported mine wastes. The proposed system thus benefited from the ?wet cover? approach to minimising further oxidation of wastes and metal leaching, but without the usual accompanying outward hydraulic gradient and leachate management issues. A sub cap drainage layer with downstream outlet was incorporated to prevent any possibility of hydraulic rupture following an unexpected rise in groundwater heads. Leakage rates from the MWMF were deemed to essentially be driven by surface infiltration rates alone (characteristic of a ?dry cover? approach), with the proposed composite capping system simulated to perform at an infiltration rate of less than 1 mm per year. A toe drain was incorporated with the perimeter containment system, and this collection together with diverted neighbouring drainage was directed under gravity to a dedicated Passive Treatment System (PTS). Overall, effluent water quality from the PTS has been predicted to reflect an annual mass metals removal in the order of 95% below baseline.

Aug 1, 2013

The Discrete Element Method (DEM) is a powerful tool for analysing the flow of charge, the energy consumption and the pattern of energy utilisation of a SAG mill. With the development of laser scanning measurement, the detailed internal working surfaces of a SAG mill can now be included in DEM models. Using scanned results for new and worn shell liners for a 32? (9.75 m) SAG mill, it is shown that the feed and discharge lifters have significant effect on the flow of the charge introducing significant threedimensionality. The effects of the resolution accuracy of liner geometry and the lower cut-off of the rock size distribution are explored. Finally, using a matched new and end of life worn liner and operating conditions taken from site surveys, the effect of wear on charge motion, distribution and energy utilisation are evaluated.

Jan 1, 2012

By Hammenm R., J. Hammen, C. Hammen

"The production of salable Rare Earth Element (REE) products necessitates a sequence of chemical separation steps between the mine and market commodities. The effectiveness of the chemical separations that purify REE salts is critical to the success of the producer, as the purity of REE salt products affects their market price. This is due to the fact that impurities in REE salts, even at low levels, can be deleterious to the function and usability of the end product. The purification of REE by removal of low levels of contaminant has been referred to as "product polishing". The technologies commonly in use for product polishing, solvent extraction (SX) and ion exchange (IEX) are challenged by the availability of separation chemistries to separate the contaminant from the desired REE salt. In simple terms, if a product specification is 99.9% purity, the SX or IEX separation reagents need to have at least a 999:1 selectivity ratio. Significant testing has been carried out on the use of solid phase extraction (SPE) columns to extract low-level impurities such as aluminum or zinc from REE product streams. The SPE columns are nano-composite materials that have rapid equilibration kinetics with the solutes being processed by the columns. The SPE matrices have been modified with chelating ion exchange ligands that bind the contaminating ion with great selectivity in residence times of a few seconds. Thus, REE streams with 1 to 2% of contaminating aluminum ions, have been polished to >99.99% purity. In this paper, results are presented on the removal of aluminum impurity from a didymium (neodymium+praseodymium) product stream using SPE technology. The selection of the SPE medium and the process steps to treat the feed solution for aluminum removal and ultimate stripping and recycle of the solid phase extractant are discussed."

Jan 1, 2014