Search Documents

By P. Condori

Palabora Mining Copper has a unique ore body composition which unlike other copper ore bodies has three main components in significant proportions; these are copper bearing ore, magnetite and dolerite. The high content of dolerite, a hard barren material, creates a high proportion of pebbles which normally are recycled back to the mill. This action increases the mill bearing pressure and power progressively until corrective actions are taken. A logical action to solve the pebbles generation would be to incorporate a pebble crusher. This in fact was done however two fundamental issues were encountered; the high content of magnetite and existence of a cyclone classification section. Due to the high content of magnetite, metal detectors have not been able to work efficiently to separate tramp metal which causes damage to the pebble crushers. The existence of cyclones in the circuit had a detrimental effect on the final product when the pebbles crusher was online producing coarse sandy material. Due to the difficulties in treating pebbles via conventional procedures and the unique Palabora ore composition and characteristics, sorting technology was investigated at laboratory and pilot scale. It was found that a combination of optical and electromagnetic sorting could efficiently separate dolerite from the copper bearing and magnetite ores. This paper reports the findings of the laboratory and pilot scale work performed and discusses the additional benefits to the circuit.

Jan 1, 2012

By B. H. Sadagah

"Construction of mountain roads at north westerly Saudi Arabia is a difficult task in rugged terrains, where the rock masses are steep slopes, and full of geomorphological constraints.Werka descent lies at the north west region of Saudi Arabia. The Werka descent, constructed four years ago harmed due to rainstorm. The rock masses are metabasalt and metaryolite tuff rocks. The road is eight m-wide, surround by unsupported sharp manmade slope cuts, reaches up to 15 to 40 m height on both sides. Failures took place at both sides of the road, and blocked it. The road of almost 2 km long subjected to all modes of slope instability such as rockfalls, manmade slope failures and debris flows in the absence of the remedial measures. The very precipitous 40 m-high rock slope-cut along the road has no benches, backed by a natural slope of almost 80 m height. Both types of slopes suffer from rockfalls and slope failure’s incidents, frequently took place mainly in rainy seasons. The steep manmade rock slope cut is less than 1 m close to the road, with no ditches, form a potentially source area for rockfall’s hazards.Intensive geotechnical study includes utilization of the RMR and GSI rock masses classifications indicates that the rocks are fair to poor quality. The DIPS, RocFall, Swedge, RocTopple, RocPlane computer program, in addition to GIS and DEM image utilized to perform modeling and deterministic analysis, in order to suggest the mitigation measures for the natural and manmade slope cuts and rockfalls. The seismic coefficients of 0.1 to 0.4 taken into consideration in modeling processes. Input parameters to model the rockfalls and slope failure’s characteristics were studied such as GSI, block size; seeder points, locations of fallen blocks; slope angle, restitution coefficients, and slope roughness. The programs modeled the proposed location, height and energy of the rockfall barriers, collectors, and rock bolts. Two manmade slope cuts studied and modeled utilizing the integrated techniques were to eliminate the risk of slope failures and rockfalls through the construction of remedial measures, this is the study objectives."

Jan 1, 2015

By H. A. Steane

"This presentation will cover some crushing and grinding considerations in plant design and operation. There is nothing basically new in the subject matter presented here; however, the viewpoint and interpretation may be novel and some of it controversial.The presentation is based on experience gained in the metallurgical design of plants for Placer Development Limited from 1960 to the present. The plants are listed on SLIDE No. 1.These plants have conventional crushing, followed by rod mill and ball mill grinding. I would like to think that autogenous grinding plants are the answer for eliminating secondary crushing plants and reducing the capital and operating costs; however, the autogenous plants seem to have some problems of their own and I have had no experience with them.Fineness of Grinding RequiredFirst let us consider the fineness of grinding required.The fineness of grind will affect the recovery obtained, and the relationship must be determined. If the grinding is too coarse, some of the valuable mineral, either free or locked in middling grains, will not be floated. However, as grinding is probably the greatest single operating cost, we do not want to grind any finer than is justified economically.Finer grinding should not be carried beyond the point where the net smelter return for the increment saved becomes less than the added operating cost. Even this fineness will be beyond the economic limit because of the additional capital cost for the equipment needed to achieve it. These factors will be discussed in more detail later.The Bond work index is the commonest method of expressing a measure of the effort that has to be expended in grinding. It is the kilowatt-hours required to reduce a ton of rock from an infinite size to 80% passing 100 microns. The formula allows a calculation to be made for other size ranges."

Jan 1, 1976

By J. W. Reynolds

"The use of approved fire-resistant hydraulic fluids in equipment operating underground was made mandatory in British Columbia by amendment to the Provincial Mines Regulation Act effective January 1, 1975. This paper covers the action taken to achieve this, in the largest underground metal mine in British Columbia. Some evaluation of costs and effects based on experience to date is included.BackgroundAn amendment to the Mines Regulation Act of the Province of British Columbia was passed in July 1974 as follow s: "" Rule 111 (b) Hydraulic Fluids. After the first day of January 1975, all hydraulic fluids used in equipment operating underground shall be of a fire-resistant type accept able to the chief inspector.""Unquestionably, its intent was justified as a safety improvement measure. The list of fires in mines involving machinery where hydraulic fluid was a factor in the fires is long and sobering. In British Columbia, in a 22-month period from 1972 to 1974, there were six fires in metal mines resulting in extensive equipment damage and injury to four workmen. Nevertheless, no provision was made for research or development of systems modifications compatible with conditions encountered in B.C. and, as late as June 1977, the Mining Association of British Columbia continued to argue that fire suppression systems should be considered sufficient until a universal suitable hydraulic fluid could be developed. The sole concession was to issue permits for continued use of mineral oil in equipment bought prior to 1975 in order to allow producing operations to continue. The burden of developing the necessary technology was laid on the industry.The Sullivan Mine at Kimberley, the largest and longest established underground mine in the province, and Cominco's most important source of ore s for its smelter at Trail, B.C., was at the outset of a conversion from conventional to trackless mechanized mining methods in pillar recovery operation s. Introduction of fire-resistant hydraulic fluid s had to be done in a period of change, in many instances on equipment for which no data existed, and called for research which had to be done while retraining the work force.The introductory phase is complete. All equipment is on FRF, the requirements of Rule 111(b) are being satisfied, and a number of research and development programs continue."

Jan 1, 1980

By R. Nendick

"IntroductionThe Ancient Egyptians recovered gold from the mud in the bottom of ponds by having teams of maidens sit around the pond dipping goose feathers dipped in grease into the mud. The gold would preferentially stick to the oily surface and was periodically washed off to give a gold concentrate. This was a forerunner of today's flotation processes.In Greek mythology Jason and the Argonauts pursued the Golden Fleece, which was a primitive form of gravity concentrate produced when gold ore slurry was passed over a sheeps fleece. The heavy gold settled and was caught in the fleece, producing a rich concentrate that allowed Jason & Company to perform the first recorded case of highgrading. The process was a forerunner of todays shuiceboxes used in placer mining.From these simple beginnings, gold metallurgy has progressed to a state where very complex flowsheets are proposed, sometimes to perform a simple metallurgical task. Figure (i) shows a hypothetical flowsheet to identify the range of unit processes that might be brought to bear on a refractory ore. The flowsheet identifies the three primary areas of gold metallurgical operations:Ore PreparationExtractionRecovery."

Jan 1, 1986

By F. C. Lendrum

"This paper had its origin in a panel discussion organized by the Canadian Uranium Producers Metallurgical Committee (CUPMC) at their Annual Meeting in Blind River in May, 1964. The reason for the panel was the formation of the National Uranium Tailings Research Program funded in the amount of ten million dollars by the Federal government. According to the bureaucrats in charge the program would seek to solve the perceived problems as well as any actual problems they believed existed with uranium tailings. Dr. Allan Ashbrook of Eldorado Nuclear chaired this panel and his summation of the panel's purpose was set out as ""Regulation and the Regulatory Process in the Nuclear Industry, Where Have We Been, Where Are We Now and Where Are We Going""?"" This paper will try to relate these questions to the whole mineral industry.The Canadian Mining Association has been telling us our natural resources are today required only if they are competitively priced with those produced in so called ""third world"" countries where labour rates are lower, environmental restrictions may be less and every effort is made by the local government to sell their product. It is in this hostile economic climate that the Canadian mining industry now finds itself. Before going further I want to stress these comments apply only to: a) Mines financed by private capital in a free enterprise society.b) Mining companies want to operate in an environmentally safe manner. However, they must earn a profit because no company financed with private capital can borrow money ad infinitum.WHERE HAVE WE BEENNone of us today would want to return to the days when the mill waste management system consisted of pumping the tailing to the nearest slope and letting nature's law of gravity do the rest. This was the way it was in early gold mines in Nova Scotia, tin mines in Cornwall, England or silver mines in Cobalt, Ontario and survives today in countries where climate, customs and methods of doing business are far different from Canada. As mill tonnage rates increased, more sophisticated systems evolved often designed for mining areas with different climates. Systems imported from arid climates such as south-west United States retained the solids but allowed bacterial oxidation of the sulphides promoting acid drainage. Environmental regulations were introduced and Canadian mines learned to handle tailings in our climates."

Jan 1, 1986

By X. Cao, P. Wanjara, J. L. Fihey, X-T. Pham, F. Mirakhorli

Single-pass hybrid laser-arc welding of 10-mm thick cast plates of CA6NM, a low carbon martensitic stainless steel, was carried out in butt joint configuration using a continuous wave fiber laser at its maximum power of 5.2 kW over welding speeds ranging from 0.75 m/min to 1.2 m/min. The microstructures from the fusion zone to the heat affected zone and base metal were characterized after post-weld tempering at 600°C for 1 hour. From optical and scanning electron microscopy examination, the fusion zone was observed to mainly consist of tempered lath martensite and some residual delta-ferrite. The mechanical properties including microindentation hardness, ultimate tensile strength and Charpy impact energy were evaluated in the post-weld tempered condition and correlated to the microstructures and defects. The ultimate tensile strength and Charpy impact energy values of all the fully penetrated welds in the tempered condition were acceptable according to ASTM, ASME and industrial specifications. The failure mechanisms during tensile deformation and Charpy impact loading were examined by scanning electron microscopy, fractography and optical metallographic analysis near the fracture origin.

Jan 1, 2015

By A. P. Bois, K. Saleh, A. Ghorbal, V. Hajiabdolmajid, G. Ballivy

"The knowledge of the initial stress field is not always sufficient to ensure the stability of mining stopes due to the high-stress variations generated by mining. Monitoring of these openings is then necessary and can provide quantitative information (deformations and stress variations) as well as qualitative information (state of stability).An applied technique for following the variations of stress and deformation in static and dynamic conditions, in relation to the evaluation of the stability of underground openings known as “Cylindre Instrumenté de l’Université de Sherbrooke” (CIUS) is discussed in this paper. In addition, a data acquisition system combined with a rock failure warning system has been developed to be connected to the CIUS for detecting the instabilities, which can endanger the stability of underground openings. Also, the installation of six CIUS and a data acquisition system as well as the selected procedure of programming in a warning system are briefly described."

Jan 1, 2003

By Michel Robert

"In 1974, Copperfields Mining Corporation and Soquem formed a new company, Niobec Inc, to bring the niobium deposit of the St-Honore carbonatite into production.St-Honore is located in the Saguenay area, near the cities of Chicoutimi and Arvida, and about one hundred and forty (140) miles north of Quebec. The discovery of the carbonatite complex was made in the fall of 1967 as a result of an airborne radiometric survey in search of uranium. The detailed exploration of the carbonatite indicated two niobium-bearing formations besides the original discovery of a rare earths zone. During the following years, the niobium formations were defined by diamond drilling and a decline was driven down to obtain adequate samples for metallurgical evaluation. In 1974, after seven hundred (700) bench scale tests, eleven (11) months of pilot plant 2nd a worldwide market research, a joint decision was made to initiate the development of a fifteen hundred (1500) T.P.D. mine and mill, under the management of Teck Corporation. The construction of the facilities were completed in early 1976 both on time and within budget. Niobec is now the only north american and the world second largest producer of Niobium concentrate.The process used at Niobec was developed from the pilot plant programs and later modified by the mill personnel. A simplified flowsheet for this process is shown on the slide. Briefly, run of mine ore is crushed to minus 5/8"" and fed to a rod mill, ball mill, and screens circuit where the ore is ground to 92% passing 65 mesh. The ore is deslimed in two stages of cycloning, and the final cyclone overflow at 85% minus 11 microns goes to waste. The cyclone underflow is conditioned prior to flotation of a carbonate-apatite concentrate. This concentrate is cleaned twice and then pumped to tails. The carbonate rougher and cleaner tails are cycloned in two stages to change the process; water and then sent to the pyrochlore rougher flotation. The rougher concentrate is cleaned five times. This is followed by pyrite flotation to remove sulfur, leaching with hydrochloric acid to remove phosphorus and dyed to less than 0.1% moisture before being sent to packaging."

Jan 1, 1978

The importance of understanding the behaviour of cemented paste backfill (CPB) within the framework of the effective stress concept is highlighted in this paper. Only through an understanding built on this concept can problems such as barricade loads, the rate of consolidation and arching, be fully understood. The critical importance of the development of stiffness during the hydration process, and its impact on factors such as barricade loads, is used to illustrate why conventional approaches that implicitly ignore the effective stress principle are incapable of capturing the essential components of CPB behaviour.

May 1, 2007

By Göran Bäckblom

The Swedish mining companies LKAB and Boliden, the equipment supplier Atlas Copco, the general contractor NCC and the specialist company Reflex joined forces in 2005 to advance the field of rock technology for the purpose of mining and underground construction. The creation of the company Rock Tech Centre is part of the strategy developed by the Swedish mining industry to strengthen co-operation with industry, academia and society. This paper outlines the current R&D strategies developed for the industry in general, discusses what focus areas are selected and provides some details on the current RTC project portfolio, especially faster and better drifting.

May 1, 2006

By A. F. Banks

"Potash processing in Canada commenced on a commercial scale in 1962. Over the last 25 years it has grown into a world-class industry with many advances in processing technology. As it is a relatively young industry, many more advances can be expected. Unlike much of the mineral production in Canada, potash is sold as a range of finished products. The processing involves potash recovery and finishing in about equal amounts in terms of the effort of processing. Environmental concerns are not insignificant and are being treated uniquely in some areas. Research and development efforts, while not carried out on a large scale, are attacking industry problems on a wide front.THE INDUSTRYThe Canadian potash industry has 12 producing mines, 10 in Saskatchewan and 2 in New Brunswick. The total productive capacity of the industry is 18,300,000 tonnes of products per year. At capacity, the industry 1•ill process the equivalent of about 53,000,000 tonnes of ore per year. Plants range in size from 8,000 tonnes to 24,000 tonnes of feed per operating day. In product terms this is from 2,500 to 3,500 tonnes of products per day.Of the 12 mines, 11 are conventional underground mining operations with potash recovery principally by flotation supplemented by crystallization and one is a solution mine where mining is achieved by dissolving the potash and salt in underground caverns and then treating the solution in an evaporator/ crystallizer circuit. In all plants there is commonality of unit operation in the product screening and compaction sections. There are three principal ores being treated in the conventional plants. These may be characterized in general terms as follows:"

Jan 1, 1987

By Kristie Tarr

Portland cement is primarily used to solidify backfill in underground mine workings and it represents a major cost in mining operations. CANMET-MMSL has invented an alternative binder technology that does not contain any amount of Portland cement and is made using waste materials, such as development rock and smelter slag. The technology has been successfully tested with many types of base metal and ferrous slag. Research conducted in collaboration with several mining operations in Canada has shown that the CANMET-MMSL binder has considerable potential as a replacement for Portland cement in mine backfill. An integral part of the overall mining operation, backfill is used for two main purposes: safety and environmental remediation. Depending on the mining method used, backfill provides a working surface, stabilizes stope and pillar walls, as well as the surrounding rock mass, and controls caving of stope backs. There are several benefits associated with the replacement of Portland cement in backfill, including reductions in (i) the footprint by placement of slag waste underground, (ii) the environmental effects and long term liability resulting from disposal and containment of slag waste on surface such as acid rock drainage, (iii) GHG as a result of reduced Portland cement usage (the production of 1 ton of Portland cement produces 1 ton of GHG), and (iv) the significant costs associated with reduced Portland cement usage.

Oct 1, 2010

By R. D. Brown

"AbstractOver the past five years, tax rates in the Canadian mining industry have skyrocketed upward across Canada, as both federal and provincial governments have sought to increase their share of mining revenues.However, the past few years have not only brought high tax rates to the industry, but also a number of important new federal and provincial tax incentives.In large part, these incentives ~ special credits or reduction in tax for carrying out specific exploration, processing or other activities - have helped to moderate the adverse effects of the higher tax rates and have provided inducements for exploration and processing activities which might not otherwise have been undertaken.However, the effectiveness of certain of these incentives can be questioned: our over-all tax structure now consists in large part of punitively high marginal rates with some extraordinarily generous but capricious tax reductions for specific activities and may not be in the best long-term interest of either the industry or the nation.A rational tax structure, with moderate and stable tax rates, together with reasonable incentives confined to activities specifically requiring them, could be a more effective spur to investment than the present tax and incentive jungleIntroductionIN THE YEARS since federal tax reform, the mining industry in Canada has faced a continued escalation in its tax burdens as federal and provincial governments have leapfrogged each other in imposing new and higher taxes on the industry. The result has been that marginal tax rates imposed on mining and processing activities throughout Canada have jumped to hitherto unparalleled levels."

Jan 1, 1977

By R. H. McMillan

A classification of important uranium deposits which utilizes both genetic and descriptive criteria is presented. The dual aspect is useful because, while the non-genetic nomenclature for the different deposit types is amenable to various interpretations, the critical characteristics of each deposit type can be analyzed to clarify various genetic points. Although the classification is intended primarily for Canadian uranium deposits, most of the important deposit types known elsewhere can be accommodated.

Jan 1, 1978

By P. R. Richardson

"Milling is the weak link in the process chain of many mineral operations. While this activity accounts for only a relatively small proportion of the direct costs of most mineral processing complexes, there are intangible and indirect costs associated with milling which are extremely large. For example, significant opportunity costs are associated with the relatively low yields which characterize this stage of the process.There are changes abroad in the world which I believe are going to cause us to reformulate the whole concept of milling. Increased competition in mineral markets are going to force managers to look anew at the high mineral values reporting to tailings which are a high opportunity cost for many operations. Tailings recovery plants are not the ultimate solution to this problem. Greater environmental concerns are going to increase the costs associated with tailings disposal and force the mining industry to look for other ways to dispose of waste products. Technology changes currently underway in manufacturing and other process industries, such as the automated 'lights-out' plant are going to be brought into this industry, and the changes will be dramatic.These are major long term changes which probably seem rather remote to many managers and professionals in existing operations which are faced with much more mundane challenges arising from day-to-day operations. However, I believe that milling is increasingly a 'lean and keen' operation involving fewer and fewer people, but who are increasingly skilled and professional. Traditional cost management approaches are no longer adequate and the industry has to take a new look at the nature of cost reduction in this core activity. This stage in the mineral process provides opportunities for value creation leading to a significant unit cost advantage for the corporations willing to adopt a total cost approach."

Jan 1, 1988

By G. C. Bateman

Canada is a very large country with a small population which is growing very slowly. We have great natural resources, but with our limited population we are continually looking afield for new capital to develop these resources. Our mining areas are among the most important fields offering opportunities for new capital and because of the wide-spread appeal which mining makes this industry commands a great deal of attention. While we are glad to see new capital from any source, we welcome it particularly from Great Britain, for, although we offer equal opportunities to the nationals of any country we would be glad to see the development of our natural resources financed as far as possible within the Empire. However, when we invite ne capital we must accept certain responsibilities, and while we have opportunities to offer, we should ask ourselves how these opportunities are taken advantage of and what sort of treatment the foreign investor receives.

Jan 1, 1925

"Mining with blast holes drilled upwards may be done to recover sill pillars, or for economic reasons when the distance between the levels is relatively large. If the rock is sufficiently competent to accommodate large stope size, the distance between sublevels could be increased to as much as drilling accuracy allows. The same drill drift can be used for the drilling of both down holes and up holes. In the case of down holes, the initial opening of the stope (drop raise) is not as much a problem as for the inverse drop raise for mining with up holes. This is because, with a drop raise, a lot of space is available at the toe for the blasted rock to expand. In addition, the raise can be blasted in many shots, thus allowing smaller blasts each time. Inverse drop raises are generally much more difficult to blast because of the limited space for muck flow, and must, therefore, be taken down in a single blast, requiring special considerations in order to ensure a success. A case study of a 29 m (95 ft) inverse drop raise successfully blasted in a single shot at Heath Steele Mines is described. The paper covers technical considerations such as drilling accuracy, hole deviation survey, delay extension and protection, initiation methods and initiation sequence. Finally, a novel method for creating the initial opening called ’slot drilling’ is presented. This method, inspired from LKAB in Sweden, consists of drilling a row of interconnected holes using a special guide mounted on a regular production drill hammer.With a case study of blasting an inverse drop raise of 29 m (95 ft) in one blast, this paper further discusses some technical issues that are critical for the development of inverse drop raises. A novel method for creating the initial opening with a slot of interconnected holes is also presented with the experience acquired at different mine sites across the Noranda group."

Jan 1, 2000

By G. R. Heffernan

"In the early 1970ssteelmakers worldwide were looking forward to many years of expansion and profitability. Huge government investments in Europe, the United Kingdom, Japan, Brazil, and Venezuela were committed in anticipation of growing market s based on long-term OECD forecasts. In 1973 the first OPEC oil shock occurred. Steel demand shrank. Restructuring became the buzz word of the day as billions of dollars in taxpayers' money was poured into eliminating excess capacity and labour. In the United States, where government help was not available, inefficient companies went bankrupt; capacity was cut to 100 million tons from 155 million tons. The industry throughout the industrialized world shrank. By 1979the world economy seemed back on track and a modest degree of optimism could be detected in the international steel fraternity. Then came the second oil shock. By 1982 the industry was in the midst of another shakeout. More bankruptcies, more rationalization, and fewer jobs resulted. In Canada some well-known companies came close to the brink as low prices and high interest rates took their toll. In the light of the turmoil in the steel market over the past 20 years an attempt to forecast the trends through to 2001 is intimidating.However, there are good reasons to be optimistic today about both markets and technology.An economic super power is emerging in western Europe as 1992 draws near. The creation of a single market of 320 million well educated and economically ambitious people has major positive implications for steel demand. The mega projects of the channel tunnel, a European network of high speed railways, and the London docklands are the forerunners of greater things. Still to come is another $200 to $300 billion by the year 2001 in identifiable major projects for highways, railways, airports, water and sewage systems. Add to that the demands of an increasingly affluent population for automobiles, appliances and housing. On top of all that place large increasing demands for electric power and you have a potential beyond anything seen during the 1970s and 1980s. In 1988 the EEC steel industry operated at 90% and in 1989 at 92% of effective capacity. A surge in spot prices indicated that 92% was close to the ceiling. This pace moderated in early 1990 but any slack will probably be taken up rather quickly."

Jan 1, 1990

By M. Askari, M. H. Parsa, S. Kashani-Nejad

Sarcheshmeh refractory consumption rate is about 7.5 - 8 kg/ton of the produced copper, which is almost three times higher than the other smelters practice. High destruction rate of tuyere zone refractory controls vessel productivity and operational lifetime. In this research with the aid of cold model and computational fluid dynamic (CFD), melt recirculation pattern and gas - liquid plume properties in the wide range of gas blowing conditions were studied. Results revealed that in addition to the well-known mechanical refractory destruction mechanism, fast tuyere zone refractory destruction could also be related to the cold bubble cluster formation near tuyere tips and introducing severe thermal shock to the refractory surface. Removing accretion and its strong bonds to the refractories around tuyere tip, causes refractory mechanical destruction and increases tuyere diameter. Increased tuyere diameter, in turn assists gas discharge in the bubbling regime. Air blowing in the bubbling regime result in the formation of big bubble clusters, bubble breakup and back attack occurrence which all found to have major impact on the refractory lifetime. Outcomes of this research, contributed to the plant converting management, blowing hardware and instrumentation improvement.

Jan 1, 2004