Search Documents

By Aleksandar N. Nikoloski, Tendekayi Tapera, Glen P. O’Malley

Chalcopyrite (CuFeS2) and enargite (Cu3AsS4) are among the most important copper sulfides. At present, many known deposits of these minerals are uneconomic to process because they are of too low grade, insufficient size or too remote to be cost effectively treated with conventional technologies that can deal with their refractory nature. Therefore, developing an effective, low cost extraction process for recovery of copper from them is important. The research presented in this paper will deal with potentially cost effective strategies involving catalysed processing, studied under conditions relevant to recycle heap leach conditions. The present account summarises some of the main findings from the research program carried out at Murdoch University between 2014 and 2018 that has investigated the effects of the common leaching parameters, major and minor species present in the leach system and additives on the rate and extent of copper extraction from low-grade ores, in which primary copper sulfide minerals such as chalcopyrite and enargite were the dominant copper minerals. The study involved batch leaching tests, detailed structural and mineralogical characterisation and thermochemical modelling under conditions relevant to heap leaching. The results have demonstrated that silver in particular has a strong catalysing effect on the extraction of copper from ore under the leach recycle conditions and, at an adequate dosage, can effectively overcome surface passivation, enabling almost complete extraction of copper from chalcopyrite as well as enargite. The aim of this paper is to present the effect of the studied additives and to briefly elaborate on the mechanism of the silver catalysed leaching process. In addition, the presence of certain secondary agents was shown to lower the critical dosage of silver and promote extraction. The data from the study allowed the development of a theory for the silver catalysed reaction mechanism, which enables further optimisation and cost-effective application of this strategy in practice. INTRODUCTION Researching the extraction of copper from chalcopyrite is important as it is the most abundant copper mineral in the earth’s crust. The majority of ores containing this mineral are processed by flotation to produce a concentrate, followed by smelting and electrorefining. However, most reserves available nowadays are of low grade or limited in size, and therefore not suitable for this conventional approach. Hydrometallurgical processing via heap leaching with or without the aid of bacteria has been shown to be potentially economical. Chalcopyrite is refractory though and suffers from slow leaching kinetics and poor overall extraction, so understanding the mechanism of how it leaches has received significant attention by researchers working in this field over the past 50 years. The refractoriness, which is the main issue with the hydrometallurgical approach, is generally described as passivation of the chalcopyrite surface whereby a surface coating is formed that blocks the reaction interface or wetting of the chalcopyrite, limiting the copper extraction. Exactly what this layer is made of or how the issue could be overcome has been the subject of intense study and debate for many years. One of the limitations of the work to date is that much of the research focus has been on typical initial leaching conditions, while there has been relatively little research into how the leaching is affected under recycle solution conditions where certain metal ions (Fe, Mg, Al) have often accumulated in the liquor. This occurs because the leach solution exiting a heap contains many species from the dissolution of gangue minerals and typically this solution is returned to irrigate the heap, once the copper has been removed, leading to an accumulation of these species.

Jan 1, 2019

By G. F. Raymond, W. P. Armstrong

"At the time of this study, the Valley mine was producing 23 000 tonnes of ore per day from a large, low-grade porphyry copper orebody. Sulphide mineralization, principally bornite and chalcopyrite, occurs in a stock work of quartz veins in one phase of the Guichon Creek batholith. The property was explored from 1967 to 1982, and was placed in production in 1983.Using a three-parameter lognormal approximation developed by G.F. Raymond at Similkam een and Mount Isa Mines, a geo- statistical conditional probability ore reserve was estimated prior to mining. Comparisons with blasthole kriging and milled ore for the first 17 months of production showed close agreements at all cut-offs between conditional probability estimates and mineable ore. This was not true of either kriging or polygon estimates. An important part of this work was identifying and correcting for bias in both exploration and blasthole samples.IntroductionCominco's Valley lake deposit is a large, low-grade, porphyry copper orebody in the Highland Valley of British Columbia. Total indicated plus inferred ore reserves are 700 M tonnes at ore grade of 0.47070 Cu. At the time of writing, ore milling is at a rate of 23 000 tI d through the old Bethlehem mill. Mining is in 10m horizontal benches using 9.8 m3 shovels and 90 tonne trucks. Since this paper was written, Valley and nearby Lomex have been combined into Highland Valley Copper with a combined oreproduction of about 120 000 tI d.Copper mineralization, principally bornite and chalcopyrite, is regularly distributed throughout the deposit as disseminated low-grade within a granodiorite host rock, and as higher grade veinlets within a stock work of near-vertical quartz veins generally 10 cm or less in width. It is likely that problems with sample variability and sample bias are mainly related to mineralization within quartz veining. Valley geology has been described in detail by Allen and Richardson and by Osatenko and Jones (2). The exploration sampling program and identification of diamond-drill sample bias have been discussed by Armstrong and Newman'»."

Jan 1, 1988

By P. Venkatasubramanian

"In recent years, computer based ""expert systems"" have been taking on large complex tasks for which no exact algorithmic solutions are feasible; tasks previously reserved for human experts requiring empirical knowledge, judgment, experience, developing a ""best solution "" by the use of plausible reasoning. Mining method selection is an appropriate area for the application of an expert system because extensive and detailed knowledge is required to make a ""best"" interpretaion of frequently ambiguous geological information. The expert system model presented here would enable users to apply expert knowledge to the evaluation of methods for coal deposits mineable by underground methods. IntroductionIn an increasingly complex and specialized world, human expertise spanning scientific, economic, social and political issues plays an increasingly important role in all branches of engineering. This is especially true of mining engineering. The number of scientific and professional disciplines involved in mine planning and evaluation, illustrates the problem. A conservative list includes geology, geophysics, geotechnics, hydrology, mining, environment, and economics.Engineers are almost obliged to be experts in at least one of the above disciplines if they are to handle the volume of information required in the planning process. Although computers have become indispensable tools in many endeavours, there is continued reliance on the human expert's ability to identify and synthesize these diverse factors, to form judgments, evaluate alternatives , and make decisions . This is especially true with regard to problems that are not easily amenable to precise formulations.The precious resource of human expert is also fragile and transient. The departure of a crucial expert from an organization ma y cause serious dislocations. Senior experienced people impart their knowledge of younger colleagues, but the demand for their talent may not leave sufficient time for such educational efforts. In recent years, computer based "" expert systems"" have been taking on large complex tasks for which no exact algorithmic solutions are feasible; tasks previously reserved for human experts, requiring empirical knowledge, judgment , experience, developing a ""best solution"" by the use of plausible reasoning."

Jan 1, 1988

By Robert Lee

"International competition is presenting the Canadian steel industry with a major challenge. While Canadian companies have invested in new technology, research and development, activity by Canadian industry, in general, lags significantly behind that of its major competitors. While OECD countries increased their research and development spending during the 1980s, Canada's R&D funding levels have changed little since the early 1970s and have actually dropped since 1986, despite greater public discussion on the issue. This fact is reflected in the relatively slower pace of innovation in the Canadian steel industry, despite the efforts of both government and industry.In addition, there are a number of factors that undermine the competitiveness of the Canadian steel industry, in particular in relation to the United States. Among these are higher interest rates, labour costs and tax rates, as well as an overvalued Canadian dollar. Canadian steel companies are thus feeling the full impact of the current economic recession. This recession, combined with recent strikes, have, for example, caused serious losses for Algoma and Stelco.In spite of these objective difficulties, the Canadian steel industry has been able to survive and continues to strive for a leadership position in the world market. Since World War II, heavy investment in new technology has allowed the industry to upgrade its facilities and increase productivity, while at the same time improving quality and reducing pollution. This last point is particularly important in view of public insistence on improvements to the quality of the environment. Over the next decade, this technological innovation must be maintained and intensified if industry is to meet the challenge of international competition and attain a leadership position."

Jan 1, 1991

By J. C. Keenan

Company-community agreements are widely considered to be a practical mechanism for recognising the rights, needs and priorities of peoples impacted by mining, for managing impacts and ensuring that miningderived benefits are shared. The use and application of company?community agreements is increasing globally. Notwithstanding the utility of agreements, the gender dimensions of agreement processes in mining have rarely been studied. Prior research on women and mining, however, does show that women are often more adversely impacted by mining than men, and face greater challenges in accessing development opportunities that mining can bring, however there is currently little to no guidance for companies, government or communities in terms of bringing a gender perspective to the fore in mining and agreement processes. While it is undisputed in human development literature that investment in women and sensitivity to gender delivers long-term health, education and local development outcomes, a number of key factors remain unexplored in debates about mining and development. These include: women?s participation in agreement processes, the gendered distribution of agreement benefits, and the extent to which impacts and benefits influence (either positively or negatively) women?s development and economic inclusion. This paper presents the results of an applied research project undertaken by the Centre for Social Responsibility in Mining (CSRM) at The University of Queensland and funded by a partnership between the Minerals Council of Australia (MCA) and the Australian Agency for International Development (AusAID). The project sought to connect with practitioners who had been directly involved in agreement processes to hear grounded perspectives on the interaction of gender dynamics and agreements, and connect those experiences with the broader literature. Findings from this study have implications for the role of companies and governments in promoting gender equality and empowerment as part of their commitments to sustainable development. A key challenge for companies will be navigating the territory of cultural norms and gender equality. The authors argue that without consideration of the gender perspective, and appropriate responses, mining agreements may not be inclusive or representative and may exacerbate gender inequalities and fail to contribute to long-term sustainable development.

Aug 1, 2013

By D. D. Hogarth

"Edward Haycock, Engineer and Public Contractor Edward Haycock was born in Shrewsbury, England, June 14, 1813. His father was John Haycock, a timber merchant and soap manufacturer, residing at Swan Hill Court, Shrewsbury, and his mother Esther was the daughter of William Hilton of Hempstead, Hertfordshire. Edward's paternal grandfather, John Hiram Haycock, was the first of a line of architects that ""changed the face of Shrewsbury"" and ""provided some of the best examples of typical Victorian architecture in Shropshire""(1). Nothing is known of Edward's early life or education, although it appears that he made no attempt to follow this artistic trend. In 1833, Edward immigrated to Canada. The following year, he married Mary Butler, daughter of Johnson Butler, a Lieutenant-Colonel in the Lincoln Militia during the War of 1812. Mrs. Haycock, as co-heiress of Johnson Butler's estate, was assigned 600 choice acres of farmland in Brooke Township near present-day Sarnia. This alone would have guaranteed a tidy income, but the Haycocks soon disposed of this land, the last lots being sold in May 1840. Instead, Haycock turned his hand to engineering and, for a number of years, was employed by the Great Western Railway first in Woodstock and later in Hamilton. He then moved to Port Hope, tried farming, worked in the engineering office of the Port Hope, Lindsay and Beaverton Railway Company, and later constructed a portion of this railway(2). During his stay in Port Hope, Haycock met his future partners Ralph Jones, a contractor, and Thomas Curtis Clarke, chief engineer with the P.H.L. and B. Railway Company. The alliance was styled Jones, Haycock and Company and their most successful venture was the construction of the Government Buildings in Ottawa. This work was the crowning achievement of Haycock's career and, no doubt, his proudest moment was at 11:30 a.m., April 2, 1860, when his daughter Mary Emily, then a little girl of 4, with a special silver trowel ceremoniously laid the first stone. Of special interest in this project were the quarrying operations, which introduced Haycock to the art and difficulties of mining as well as to the potential returns of mines. Sandstone, for facing, was drawn from four quarries, 10 to 12 miles from the Departmental Buildings. Haycock seems to have been in charge of these operations, which in the early stages involved an average labour force of 86 men and 43 teams. However, by 1861, quarrying had declined in importance and the contractors were able to concentrate whole-heartedly on the construction site."

Jan 1, 1999

By Tao Long

Recently, the great amount of funds has been invested in the reconstruction of damaged infrastructure and house of subsidence area of coal mine and mine reclamation. This is a benevolent and popular work, which is highly praised. However, because of complicated collapse area problems in China, especially the less integrated control research in the collapse area of metal mine, and the technological weakness, how to effectively control the subsidence area, restore landscape and ecological environment, and utilize the abandoned mine land, are major issue related to the mining area of sustainable development. The research situation about the formation of metal mine collapse area at home and abroad is reviewed, and then the effect of the collapse area on the mine safety and ecological environment, the existing technical problems and development direction are analyzed. Lastly, the technical measures of the collapse area control and cooperative underground mining is put forward.

Oct 1, 2010

By W. Geslin

Backward extrusion process is a metal forming process, which limits the manufacturing?s extra thickness when compared with classical die forging technique. Because of a lack of alloy?s mechanical behavior knowledge, the basic strategy of design is as follow: ?Definition of a small scale blank ?Performing experiment in order to get useful process data ?Improvement finite element simulation conditions ?Development of the full scale blank forming process (design of tools,...) using the finite element simulation A comparison between the result of modeling and the experimental data has been done to validate the finite element simulation.

Aug 1, 2010

By K. Thuro, S. Schneider, H. Kasling, P. Ellecosta

"One of the most important methods for material testing is the characterization of the hardness, which is defined as the resistance of a material to the penetration of another one. The methods according to Brinell, Vickers, Rockwell and Knoop are today the most common and standardized tests for metal. As they are developed for predominantly ductile materials like steel, they can’t easily be applied to rocks which react much more brittle under indentation. But just as steel, rock is composed of different minerals and has a specific microstructure. Its mechanical parameters are connected with the particular grains, their cohesion and interlocking, just like steel.The abrasivity of rocks and the accompanied wear of drilling tools today are mainly determined by simple and fast laboratory tests such as the Cerchar abrasivity test or the rubber wheel test. Such laboratory tests are good tribological tests, but there are limits. The Cerchar abrasivity test for example has weaknesses in extreme cases, that mean soft or very hard rock types. This leads to an underestimation of abrasivity, e.g. in poorly lithified sandstones or very hard, fine grained and extremely abrasive rocks. As mentioned, hardness characterizes, depending on the type of deformation, predominantly plastic (metal) or elastic properties (rubber). Rocks are in the range between these two extremes. Since the rock drilling process can be seen as a kind of penetration process on macroscopic and microscopic scales, we picked up the idea to characterize the interaction of rock materials and TBM-disc-cutters with hardness tests. In addition, this supports for a better understanding of the wear process on disc cutters. We used the hardnessdisparity concept after Cardu & Giraudi (2012) because wear can be understood as the interaction between the wear part and the material which causes the wear (tribological system). Several rock-forming minerals and some fine to coarse-grained monomineralic and polymineralic rocks were tested. In contrast to Cardu & Giraudi, we used in the first step of investigations the method after Vickers with loads up to 294.2 N (HV 30), depending on the estimated hardness to get bigger indentations and therefore as well information about the cohesion and interlocking of the minerals/grains. We also tested several associated disc cutters. First results show that with higher loads (HV 5 - 30) and at least 15 indentations, we get a structural hardness in fine-grained rock samples, which allows a good characterization of the elasticity and brittleness. Nevertheless, for the coarse-grained rock samples we need up to 40 indentations for a good characterization. Using this method, a prediction of disc cutter wear is feasible taking into account the hardness of the disc cutter steel. In this paper, we would like to present this approved method in material sciences to derive an additional parameter for the characterization of rock abrasivity and wear."

Jan 1, 2015

By T. G. Joseph, G. W. Hansen

"This paper considers the duty cycle of an electric cable shovel and correlations with measured passive seismic responses of the underfoot oil sands material in-pit. It has been observed that the cyclic activity during operation of any shovel in the oil sands environment causes the material to deteriorate and provide a less than ideal footing for this large item of equipment, whose dead weight approaches 1500 tons with a footprint of merely 75 sq. yd. Consequences are manifested in the form of carbody and side frame cracks, and associated downtime, maintenance activity, cost, and subsequent loss of availability.The objective of these considerations, as part of the Oil sands-Equipment Interaction Program (OsEIP), currently a joint venture between Syncrude Canada Ltd., James Progithin International (JPi) Ltd., Caterpillar Inc., P&H MinePro and the University of Alberta, is to identify and provide feedback to the manufacturer and end user of adverse shovel-ground conditions. This would enable the manufacturer to incorporate greater knowledge into the design process and the end user to direct operations in an enhanced proactive maintenance stance."

Jan 1, 2002

By Brenda M. Dixon

A matrix analysis of the differences between the camps and communities associated with the Britannia Mine is used to develop an analytical tool. The tool is intended to assist the mining industry as it embraces the many facets of sustainable development. A case study is used to support the identification of key factors that may predict the sustainability of a new mine town. Sustainable communities, like Britannia Beach, are discussed in the context of three pillars of sustainability: value of mining products to society; creating wealth; and, environmental integrity. A sustainable mine town may be viewed as a socio-economic asset as well as an asset to the mining industry.

May 1, 2006

By C. H. Wright

Introduction The rapidly expanding and increasingly complex Canadian industrial structure, with the mining, metallurgical, and chemical industries as a large integral part, has, in recent years, brought greatly increased importance and value to our industrial minerals. In the modern economy of our mineral industry the importance which is due the non-metallics has been somewhat overshadowed by the great value of our large metal production and, in addition, by the glamour and fascination usually associated with the mining and treatment of gold ores. The term 'Industrial Mineral' is used in this paper in its usual sense and refers to non-metallics other than fuels. Coal and petroleum products, including natural gas, are considered as industrial minerals in those applications in which they are used for strictly chemical process purposes. Certain reduction metallurgical industries are so closely allied to chemical industries that for purposes been of this discussion no attempt has made to differentiate between them. Chemical industry in Canada today is a fairly large factor in our national economy, whereas in 1898, when the Canadian Mining Institute was born, it was very small indeed. Chemical concerns are largely dependent on industrial minerals for raw materials and process supplies and, as the country has developed industrially, so have the demands for non-metallics increased, not only by chemical industry but also by other large consumers, such as the construction and metallurgical industries. At the present time there is a greater than normal incentive prevailing for new discoveries, due to the serious lack of balance that exists in our import and export trade. This fact has resulted in intensive efforts to rectify the situation by locating new deposits and re-assessing those already known in an effort to enlarge and improve our home production of raw materials and also to extend their processing in Canada for our own needs and for export. The rapid advances in science and technology that have taken place since 1900 have also resulted in many cases of beneficiation and utilization of otherwise too low grade materials in order to satisfy current demands. The purpose of this paper is to indicate the history and the trends of the utilization of industrial minerals in established industry and to indicate the important part played by non-metallics in connection with the opening up of new industries. Some consideration has been given to the continual competition between natural and 'synthetic products and to the general tendency towards more rigid specifications.

Jan 1, 1948

By W. H. Zieman

NORMAN WEISS, Milling Engineer, American Smelting• and Refining Company: The subject of the Forum on Rod and Ball Mill Liners is very fascinating, and there is no end of discussion when operators get together on grinding. However, the hypotheses and suppositions easily outrun the facts, especially when we •consider the inaccuracy of many reported observations. Still surprisingly small is the number of concentrators even reasonably well equipped to measure power consumption of each grinding mill, together with running time, so that data on this tangible factor, at least, can be obtained with precision. While the more elaborate devices of this nature, producing for each 24-hour period the total power consumption, average kilowatt hours per hour, short-term demand chart, instantaneous demand, and print-out, may cost in the neighbourhood of $2,500 per mill and may be difficult to justify, the combination of an ammeter, watthour meter, and running-time meter will cost only a few hundred dollars, so there appears to be little reason not to in-stall them in view of their numerous advantages.

Jan 1, 1959

By T. G. Carter

"During the early part of the 1980s, four new surface coal mines commenced operation in the Province of British Columbia. Each represented a major investment in both persons and materials in order to protect this investment in one significant area-the fixed portion of the surface coal handling system-a substantial amount of work was undertaken to ensure that the system was well protected from an outbreak of fire. A great deal of effort in this field had already been made by those coal mines which had been in operation for a number of years and experience gained at these operations was utilized in determining the level and extent of fire protection for the new mines.This paper summarizes the major problems, and suggests some of the methods of solution, in providing an adequate degree of fire protection for surface coal handling systems. It will also discuss the potential for gas and dust explosions together with ways to minimize this potential.The Fixed Coal Handling SystemNote: The word ""fixed"" has been used in its present context to denote that part of the coal handling system where the coal is moved via fixed installations such as a conveyor. It differentiates from that part of the system where coal is moved by mobile equipment.The raw coal delivered to the truck dump will undergo two major processes on its way to the rail load out. The first will be at the coal preparation plant where coal of specified quality will be extracted from the raw feed to the plant. If this coal is of metallurgical quality, and sometimes if it is of thermal quality, it will pass through a thermal dryer where part of the moisture acquired during coal preparation will be removed, i.e. the second process. As the complexity of both the coal preparation plant and the thermal dryer is such as to warrant separate considerations they will not form part of this paper. Each of the processes, however, is generally, housed in its own building, thus, containment of any hazards is usually more attainable than those existing or caused in the rest of the system."

Jan 1, 1988

Current AG and SAG mill circuits have continued the trend to larger, fewer mills. These large mills place a significant additional load on the discharge systems and it has become imperative that the designs of these mill discharge systems are evaluated carefully to ensure maximum efficiency and have the capacity to be able to handle the increased mill discharge volumes. The current generation of multiphysics modeling tools allow a detailed analysis of AG and SAG mill discharge performance. The combination of Discrete Element Method modeling and Computational Fluid Dynamics allows the designer to model in detail all aspects of a mill discharge performance. This includes a detailed description of the build-up of solids and slurry in a mill discharge, the recycle of material back into the mill through the grates, the relative wear rates and the occurrence of overloading at the pinch points. These tools allow intelligent decisions to be made regarding the type of discharge arrangement, pan lifter geometry, and discharge cone design, so as to ensure that the discharge is capable of handling the duties required for a specific installation. This paper details the current state of the art in these modeling tools, and provides an overview of some recent applications.

Jan 1, 2012

By Karl J. C. Harries

"The Table of Contents that follows is only an example and is the Table of Contents from an actual negotiated agreement. It is merely intended to show how an agreement might be set out and the nature of possible provisions. As a negotiated agreement the format was dictated by the negotiations. It is not offered as a precedent of what should be contained in a joint venture agreement (“JVA”), the “proper” sequence of Articles, or a complete listing of the contents of joint venture agreements generally. The set-up used for an agreement should be decided by the parties and be one they consider flows in a logical and workable sequence. This example sets out the “deal” first, followed by the provisions relating to how work is to be carried out and then by administrative provisions necessary to make the agreement work. If you are more comfortable with, say, having the Committee provisions at the beginning, by all means have it drafted that way -- you are going to have to live with the agreement and work under it.Notes:1. The Table of Contents provisions appear in bold print. The italicized sections are annotations, which have been provided in some cases where the heading may not clearly describe the contents. They are not intended to be comprehensive, but refer to some specific matters that are considered to be of interest or to need some clarification.2. The subject matter of many of the articles and paragraphs is discussed or commented upon in the text of the book. Some of section cross-references have been provided. Such references are only to sections where the topic is a principal subject and no attempt has been made to provide a comprehensive indexing.3. Although this particular agreement is a three-party agreement, *B* and *C*, the Owners, are required to act as a unit (see para. 1.09. – § 8.44.), making the agreement effectively a two-party agreement. The parties insisted upon having a decision-making Committee and structuring the agreement accordingly. As is explained in § 8.11., such an arrangement is not recommended and can result in problems.5. See also §§ 8.24., 8.41. and 14.13. for discussions on tables of contents, summaries, and headings."

Jan 1, 2003

By W. J. D. Stone

"For several years, the existence of a deposit of barite (BaS04) near Brookfield, Nova Scotia, has been known. A very large deposit of strontium (SrS04) near Sydney, Cape Breton, is a more recent discovery. Cape Chemical Syndicate has been formed to work the deposits. A five-million-dollar integrated mineral processing and chemical plant is planned for Sydney to produce various compounds of barium and strontium. The mineral processing plant includes the Jones Wet Magnetic Separator and will produce high-purity barite and celestite. These products will be processed further in the fine grinding plant and the chemical plant. The general project is described, covering the deposits, processing and markets."

Jan 1, 1969

By Kamran Esmaieli

This paper investigates the behavior of ore pass walls under impact loads caused by material transiting through an ore pass. In particular it considers the influence of foliation in the rock mass surrounding an ore pass as both a triggering and accentuating cause of degradation. Based on empirical observations in several underground mines a numerical experiment was designed to understand the influence of rock mass foliation on impact-induced damage on ore pass walls. The distinct element method, and in particular the Particle Flow Code (PFC2D) was used to simulate three different rock masses surrounding an ore pass. Each simulated rock mass has similar properties but was defined by distinct dominant foliation (70o, 80o, 90o) along the foot wall. The numerical experiments investigated different scenarios whereby the walls were loaded by a projected rock fragment striking the foliated walls at a constant impact angle and velocity. The damage inflicted by the projectile rock fragment, on the foliated rock mass, was quantified using the number of impact-induced micro-cracks initiated on the ore pass wall. The results of the numerical analysis indicated that the presence of foliation resulted in greater damage zones in the surrounding rock mass. In addition, the extent of impact-induced damage to the ore pass wall increased as the angle of interception between the ore pass wall and the rock mass foliations decreases. This is in agreement with qualitative field observations.

Jun 1, 2012

By D. M. Hausen

"Refractoriness in Carlin-type gold ores results mostly from fine locking of gold in pyrite, locking in various gangue phases, notably quartz, and a ""preg robbing"" condition attributed to organic carbon. All three conditions may occur in any given deposit, including Newmont &apos;s Carlin and Gold Quarry deposits in Nevada, where types of ref ractoriness occur locally in minor amounts.Measurements of specific gravity, water absorption and screen size distributions of gold in alteration rock types from Gold Quarry show transitional changes from siliceous cherts through decreasingly silicified and increasingly argillized siltstones.Low permeability of siliceous ores contributes to ""size dependent"" refractoriness in cyanidation test work. Colligative physical and chemical measurements demonstrate that silicified cherty ores are difficult to grind, poorly permeable, and less amenable to cyanidation. Refractoriness in pad or column leaching of coarsely crushed siliceous siltstones and cherts is shown to correlate with interrelated measurable mineralogic and physical parameters.IntroductionMetallurgical treatment of variably amenable and refractory types of gold ore may be guided by both analytical and mineralogic data on the interlocking of gold (microscopic an d sub- microscopic) in assorted gangue/sulphide phases. Most oxidized ores from the Carlin gold mine, north of Carlin, Nevada, are amenable to direct cyanidation. The permeability of most oxidized ores from Carlin coupled with the fine size of the gold < 1.5 um) yields rapid extractions and high recovery without fine grinding.Small portions of the Carlin ore body, and also the nearby Maggie Creek and Gold Quarry orebodies, are less amenable to cyanidation, and are classified as refractory. Refractory conditions may be attributed mostly to the association or interlocking of gold with pyrite and /or microcrystalline quartz or chert, and also by the adsorption of leached gold by deleterious forms of carbon, termed ""preg-robbing"" carbon. Each of these conditions are described and defined, with emphasis on a form of silica-locking, which has been referred to as "" size dependent"" refractoriness."

Jan 1, 1985

By Charles B. Newmarch

Abstract In the course of coal studies undertaken by the B.C. Department of Mines in southeastern British Columbia, special attention was directed to problems of coal seam correlation. Methods that had been used successfully in other coalfields were found, in the Crowsnest area, to have a restricted use or furnished only additional evidence that might prove helpful when used in conjunction with other criteria. A correlation technique involving semi-quantitative spectrographic analyses of coal ashes was developed. Elements detected in the ash include Si, B, P, Fe, Mg, Mn, Pb, Ti, Cr, Ga, Ca, Al, Ge, Ba, Mo, V, Ag, ?y;b, Na, Zn, Zr, Ni, Sr, Cu, K. Of these, the elements found to be most useful in correlation were Na, Ba, Si, V, and Mg. The element Na was invariably detected in the ash from one of the seams but was not found in samples taken from any of the others. In all of the four seams sampled statistically, significant differences in the amount of certain trace elements were noted. When the values obtained for these trace elements were portrayed in the form of histograms, the resulting diagrams had a characteristic shape for each seam. The diagrams provided a basis for seam identification within the limited area (8,000 feet by 4,000 feet) that was investigated. Introduction During the field seasons of 1946, 1947, and 1948 the British Columbia Department of Mines undertook a geological investigation of the coal measures of southeastern B.C. As field work progressed in the Crowsnest area it was found that, within the Kootenay formation, which contains all the commercial seams of the region, the coal beds are the most persistent stratigraphic units. Because of relatively rapid changes in ?both the thickness of the seams and the interval between seams, difficulty has invariably been experienced in attempts at correlation. Even short-range correlati0ns by able geologists who have worked in the Crowsnest coal basin have been questioned by the operating companies. It was apparent, therefore, that a more dependable correlation technique was needed so that stratigraphic and structural studies could be of greatest value. This paper presents, firstly, a summary of the results obtained in attempted correlations using methods that have been found effective in other coalfields. Secondly, a method based on semi-quantitative spectrographic analysis of coal ash is described and the apparently promising results are discussed.

Jan 1, 1950