Search Documents

By E. Ghali, W. Zhang, M. Robichaud, G. Houlachi

"The performances of six mesh and one plate dimensionally stable anodes have been investigated in the zinc electrolyte at 38oC and compared to conventional silver-lead alloy anodes. The electrochemical behaviour of these anodes was studied by cyclic voltammetry, galvanostatic, potentiodynamic, open circuit potential and electrochemical noise measurements. It was observed that at the end of 24 h of galvanostatic polarization at a current density of 50 mA/cm2 in the zinc electrolyte at 38oC, the mesh V had the lowest potential followed by mesh III, mesh VI, plate-V, mesh IV, mesh I, and mesh II electrode. When the potentials for mesh I, mesh III, mesh IV, VI and plate-V, mesh V were compared with that of the Pb-0.7%Ag anode (1920 mV/SHE), they were found to be 6%, 16%, 7% 10%, 17% lower, respectively.After 16 h decay following the 24 h polarization, the mesh III had the lowest corrosion rate (51 mS/cm2) among the seven specimens, followed by the plate-V, mesh V, VI, IV, I and II (221 mS/cm2). For the fresh surface as received, after two hour open circuit potential measurements, mesh I had the most positive (noble) potential (1382 mV/SHE) among the seven electrodes followed by the plate-V electrode, mesh V, mesh IV, mesh VI, mesh III and mesh II (751 mV/SHE). After consecutive series of electrochemical testing, mesh V, mesh III, mesh VI had lower corrosion rates (~ 343± 6 µA/cm2) than that of mesh IV, mesh I, plate-V, and mesh II (~ 644± 143 µA/cm2).INTRODUCTIONThe continued use of lead based anodes in the electrowinning process has been mainly due to their relatively low cost as compared to other materials (Msindo, Sibanda, & Potgieter, 2010). They have good electrical conductivity, stability during electrolysis, very good corrosion and wear resistance (Ivanov, Stefanov, Noncheva, Petrova, Dobrev, Mirkova, Vermeersch, & Damaerel, 2010). However, lead-based anodes give their high energy consumption and low corrosion resistance for electrowinning. To overcome these problems, Dimensionally Stable Anodes (DSAs) has been chosen (Msindo et al., 2010). Comparing to the traditional lead anodes, the DSA anodes have many advantages: (1) no contamination; (2) no loss of anode material, pure electrolyte; (3) lower gas bubble effect through special anode designs; (4) use of higher current densities (Msindo et al., 2010). The success of DSA anodes has been attributed to their chemical stability that allows them to maintain nearly constant dimensions during the life of the anode even when operating in environment with low pH values. Due to their stability, the consumption rates of DSA are as low as 1 mg/amp.y (Alfantazi & Moskalyk, 2003)."

Jan 1, 2016

By Douglas W. Reeve, Hoc Nghia Tran, David Barham

"In kraft pulp mills, the spent pulping liquor is concentrated and used as fuel in the recovery boiler. Extensive deposits are formed in the upper section of the boiler due to the very high ash content of the fuel and the volatite nature of the ash. Deposits are composed of Na2S04, Na2C03 NaCI, some potassium salts and reduced sulphur compounds. Chloride and potassium salts are enriched in the deposits compared to the smelt due to their greater volatility.Severe corrosion of the superheater tubes in a recovery boiler has been traced to three factors: a non-uniform temperature profile in the flue gas, relatively high operating steam temperatures and high chIoride and potassium concentrations in the fireside deposits.The role of chIoride and potassium in superheater corrosion has been explained by increased Iiquid phase in deposits. Together with corrosion studies, this information has shown that kraft recovery boiler superheater corrosion due to the chloride and potassium enriched deposits can be avoided by proper boiler operation and by judicious superheater and furnace design.IntroductionThis investigation of recovery boiler superheater corrosion was initiated by the discovery of severe corrosion of the final stage superheater in a Canadian closed cycle kraft pulp mill(1,2). Metal wastage leading to tube failure was believed to be due to three major causes : the relatively high operating steam temperatures, the uneven distribution of flue gas temperature across the boiler which created a "" hot spot"" and the high chloride and potassium concentrations in the superheater fire side deposit. The mill responded to the problem by i) lowering the superheater steam temperature from 475°C to 380°C, ii) minimizing the chloride content in the spent pulping liquor, by controlling the NaCI input with recovered bleach plant effluent, and iii) changing metallurgy of a portion of the bottom section of the final stage superheater platens from ferritic steel T-22 (2.25% Cr, 1% Mo) to austenitic steel Incoloy 800H (21% Cr, 32% Ni, 46% Fe, 1.5% Mn, 1% Si, 0.6% Al) (Fig. 1). Details of the superheater corrosion experienced in the closed cycle mil! have been reported in previous papers(l ·2,) ."

Jan 1, 1984

By A. L. Hinde, H. Dong, J. T. Kalala

"The High Pressure Grinding Roll (HPGR) is gaining acceptance in the mineral processing industry and has become a competitive technology in reducing the specific energy consumption in Mineral processing plants. The amount of samples required for HPGR amenability testwork and HPGR wear tests is usually high and often cannot be available at early stage of projects were only a few drill cores are available.Although HPGR was initiated from small scale piston die compression tests, the development of small scale piston die test to predict the performance of HPGR has been slow.The objectives of this paper was to present the designs, operating procedure of piston-die press and operating conditions which have resulted in similar particle size distribution obtained from a piston die test and HPGR Labwal unit starting from the same feed size distribution. Testwork were conducted using a 2 MN piston-die press and a Labwal HPGR unit on major South African ore types, viz, gold, platinum and iron ores. The results obtained show that piston-die test can generate data to predict energy consumption, product size distribution, and even to evaluate the edge effect."

Jan 1, 2012

By B. Leonard

As of November 2012, the Alberta government listed 53 oil and gas, oil sands, and mining construction projects either proposed or currently under construction. These industrial plant construction projects have an estimated value greater than 105 million dollars. A common construction method employed for industrial plant projects is fast-track construction, which is used to reduce construction time. Contractors begin fast-track construction with highly generic scheduling information. This high level schedule turns into a lower level schedule as more detailed information becomes available. From a contractor?s perspective, a challenge faced using fast-track construction is the visualization of generic and constantly changing project schedules. This paper discusses the use of a Plant Information Modeling (PIM) system, designed to create a 4D animation to visualize project schedules for fast-track industrial plant construction projects. The proposed PIM system creates a modified project schedule by obtaining specific information from a generic construction schedule. Obtaining the information involves grouping schedule activities in accordance with the level of detail in a 3D model, and the level of detail in a project schedule. The modified project schedule is then used in conjunction with a 3D model to simulate the construction sequence in the form of a 4D animation. This allows for 4D visualization of project activities, installation dates, and crane movements. Furthermore, as engineering reaches completion, the PIM system creates a streamlined channel for schedule information updates to be easily uploaded into the model for a more accurate 4D visualization. Through analyzing a nonmodular construction case study, this paper discusses the successes and benefits of the PIM system for 4D visualization, such as increased productivity, shortened construction time, increased constructability, and decreased field costs.

Aug 1, 2013

By P. E. Weidmark

"CANMET InformationPART 1-Published PapersAsmis, H. W., ""The dynamic response of caverns in discontinuous rock""; Proc 22nd U.S. Symposium on Rock Mechanics, Cambridge, Mass, June 1981, 272-277; 1981.Austin , M.W., Bray, J.W. and Crawford, A.M., ""A comparison of two indirect boundary element formulations incorporating planes of weakness"" ; Technical Note; Int J Rock Mech Min Sci Geomech Abstr; 19:339-344; 1982.Barrett, J. R., ""Applying geotechnical theory to underground metalliferous mining""; Proc 1st Intnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of AIMMPE; 210-222; 1983.Barron, K., Wright, P.L. and Smales, T., ""Guideline s for the design of coal pillars in the No .4 seam at Mclntyre Mines Ltd ., Grande Cache, Alberta""; Proc 1st Intnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of A IMMPE; 559-578; 1983.Bauer, A., ""Wall control blasting in open pit mines""; Mining Engng; 34:155-158; 1982.Bieniawski, Z.T., "" Improved design o f room-and-pillar coal mines for U.S. conditions""; Proc 1st Intnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of AIMMPE; 19-51; 1982.Blackwell, G.H. and Calder, P.N., ""Practical aspects of wall stability at Brenda Mines Ltd., Peachland, BC""; 3rd Intnl Conf on Stability in Surface Mining; Vancouver, BC, June 1981; SME-A1ME; 3:573-608; 1982.Blake, W., ""Microseismic monitoring for underground stability "" ; Proc 1st Intnl Cont on Stability in Underground Mining; Vancouver , BC, August 1982; SME of AIMMPE; 272-294; 1983.Brawner, C.O., ""Stabilization of rock slopes"" ; 3rd Intnl Conf on Stability in Surface Mining; Vancouver, BC, June 1981; SME-AIME; 3:289-310; 1982.Bridges, M.C., ""Review of open stope mining in Australia""; Proc 1st lntnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of AIMMPE; 813-828: 1983."

Jan 1, 1983

By C. Sartain

In recent years market pressures have been building on companies to develop the next era of mining projects to follow the previous boom in copper projects of the mid 90's. However the response from the industry has been slow in coming, and somewhat muted. It is clear that there simply have not been the obvious quality projects waiting to be rapidly developed. Many of the known undeveloped copper projects have particular characteristics that have previously prevented their development, including mineralogical complexity in the ore bodies, environmental challenges or particularly difficult geographic locations. This paper describes how the Copper Division of an international mining company, Xstrata plc, is preparing to progressively develop an impressive pipeline of projects, armed with an array of proprietary technologies and with a strong approach towards sustainable development and community engagement. The approach being taken is enabling Xstrata to complement its acquisitive corporate philosophy with a management emphasis on project development and operational optimization and enhancement.

Jan 1, 2007

By P. Hubert, J. P. Ildefonse, F. Qafssaoui, J. Poirier

Corrosion tests by corrosive alumina-lime slags were carried out on commercial high alumina bricks used in steel ladle linings and model refractories (with different raw materials : bauxite, andalusite, and different microstructures). Using (SEM) scanning electron microscope and (EDS) energy dispersive spectroscopy, microstructures of slag-corroded refractory interfaces were studied in detail. The monomineral and glassy phases, the composition of reaction products and chemical profiles were determined. A thermochemical analysis based on phase equilibrium diagrams has permitted to estimate the proportion and the composition of the high temperature intergranular liquid phase. These data were compared to the experimental microanalysis results. The viscosity of the high temperature liquids were calculated according to Urbain 's model and the relationship between the viscosity and the penetration of liquid phases were discussed. These theorical and experimental results were used to understand the complex phenomena of slag penetration and corrosion of andalusite and bauxite refractories at high temperature and to propose new ways of improvements for the formulation of high alumina refractories.

Jan 1, 2004

By Louis Tellier

SIDBEC commenced detailed planning of major capital expenditures to install integrated steelmaking facilities in 1969. Today, less than IO years later, SIDBEC and its subsidiaries have completed major mining, concentrating, pelletizing, direct reduction ? electric furnace steelmaking and continuous casting plants. The total cost of these projects was almost 1 billion dollars. The philosophy behind the project planning and the evolution of management control are explained. These extensive projects were undertaken during a period of exceptional inflation and a disturbed labour climate, but were nevertheless completed with only modest overruns, with good control of timetables and with exceptionally good start-up performance. Project planning, relations with consulting engineers, introduction of new technology, purchasing and field management and cost control are discussed.

Jan 1, 1979

By T. G. Joseph, M. Welz

ABSTRACT: Joseph (2002) introduced passive seismic monitoring to measure mining equipment performance. This paper evaluates the potential of passive seismic monitoring to correlate mining equipment operation with oil sands surface response, with a mining hauler as the seismic source. When applied to moving haulers, this action–reaction approach is complex. Vibrations from on-board equipment, such as pumps and tires, dirty the signal with noise. To facilitate any correlation, the signal must be cleaned up. Existing geophysical analytical techniques were manipulated to evaluate the noise problem and to filter sufficiently to permit an evaluation of whether a mining equipment action–ground response relationships in fact discernable.

Jan 1, 2011

By T. Crivits, I. Bellemans, V. Cnockaert, K. Verbeken

It is well known that slag foaming can significantly complicate copper smelting processes. This is especially true for unpredictable events that generate large amounts of slag foam during a small period of time. These events are here referred to as eruptions and are typical for certain types of liquid bath furnaces such as modern top submerged lance (TSL) furnaces. A few authors already made the link between over- oxidation of the slag phase and slag foaming. In this work, the mechanism is studied in more detail and explained using the smelter chemistry and the behaviour of dynamic foam formation. Finally, the most influential parameters on the foaming behaviour of the process are presented. INTRODUCTION Copper remains one of the most important metals used in our modern society. In 2017, the annual amount of copper produced worldwide was about 23.5 million metric tons. This makes copper the third most produced metal in the world after steel and aluminium. The majority of this copper was produced by copper smelting, about 19 million metric tons, both from primary concentrate and secondary feed material as reported in ICSG’s World Copper Factbook 2018. In the past, copper smelting was mainly performed using Flash smelting, a technology developed before 1949 (Kojo, Jokilaakso & Hanniala, 2000). Nowadays, this type of smelter is being complemented by other smelter types such as ISASMELT and Ausmelt technologies. These are two types op smelter furnaces, based on the concept of a top submerged lance (TSL) furnace. These two technologies were both commercialized around 1990 (Arthur & Hunt, 2005). It is estimated by Wang et al. (2016) that at this time, both flash and TSL smelters contribute equally to the total amount of annually smelted copper. Flash smelting stays the most important technology for extracting copper from primary sources. TSL furnaces, on the other hand, are more suited than Flash smelters for the recovery of copper from secondary materials. This is because of the different ways that the feed material is inserted in both furnaces. In Flash smelters, the ore and fluxes needs to be fine and completely dry in order to be able to blow the mixture inside the burner area of the furnace. The feed material for TSL smelters show less constrains concerning humidity and particle size. The material is dropped from the top inside the molten bath. As a result, a more complex and flexible feed stream can be processed using TSL smelting (Wood, Hoang & Hughes, 2017). This feature will become more important in the future as primary copper sources gets more scarce and the need for a fully sustainable material cycle increases.

Jan 1, 2019

By J .. R. Brown, G. Deschenes

X-ray Photoelectron Spectroscopy (XPS), X-ray Diffraction (XRD) and Electron Probe Micro-Analysis (EPMA) were used to characterize chemically the gold complex adsorbed on activatedcarbon from a solution containing 102mglL Au and 0.5 giL thiourea. This paper also considers the gold chloride and the gold cyanide systems. The results indicate gold is adsorbed on activated carbon from the thiourea solution as the gold (I) thiourea complex, i.e. Au [CS (NH) 2];' Other gold species such as metallic gold were not detected on the carbon support. These results also suggest the elution of the gold (I) thiourea complex can be performed with high recovery.

Jan 1, 1993

By C. Beaudry

Outline ? General Geology of Frieda River Project Area ? Exploration History ? Geology of Porphyry Deposits ? Porphyry Resource ? Update of Nena Deposit and High-Sulfidation Mineralization ? Nena Resource

May 1, 2006

By Rodnei Graça, Jorge Silva Bettencourt, Lena Virgínia Soares Monteiro, Baruch Spiro, Tolentino Flávio De Oliveira

Abstract - The Vazante Mine is located in the Vazante District, the largest zinc district in Brazil. The Vazante deposit consists dominantly of an unusual willemitic ore. Small sulfide bodies are tectonically imbricated with the willemitic ore, within the Vazante shear zone. Structural styles of deformation and petrographic and isotopic evidence indicate that willemitic mineralization and deformation occurred synchronously during the Neo-Proterozoic. Various generations of hydrothermal veins and hydraulic breccias may pre-date, accompany and overprint the mineralization. Ore-formation temperatures are deduced from stable isotope geothermometry and mineral chemistry of both sulfide bodies and willemitic ore. Temperatures during the main stage of mineralization range from 206°C to 294°C (willemitic ore) and 317°C (sulfides), and reflect the prevailing metamorphic conditions within the shear zone. The fluid from which the gangue minerals of the sulfide bodies precipitated (at 250°C) had an oxygen isotopic average value of ?18O = +19.4‰. This value appears to reflect the interaction of metamorphic fluid with the carbonate rocks of the Vazante formation. At 250°C, the fluid in equilibrium with the vein mineral phases and willemitic ore assemblage exhibits a uniform oxygen isotopic composition, with an average value of ?18O = +11.5‰. The positive linear covariance of ?18O and ?13C ratios of the carbonates is most likely due to the mixing of metamorphic and meteoric fluids. The ?34S values of sulfides indicate a direct crustal origin for the sulfur. It is suggested that the sulfur is largely derived from pre-existing sulfide bodies and has been transported by metamorphic fluids. The willemitic ore may have originated from the precipitation of metal in sulfur- poor fluids under oxidized conditions, within the Vazante shear zone.

Jan 1, 1999

By Walter Valery, Sergio Vicuna, Roberto Valle, Hamer Arevalo, Ben Burger, Lui Vargas, Alex Jankovic, Jim Seidel, Eduardo Nozawa

This paper describes the design, the first three years of operation and optimization of a large, single stage SAG mill at Minera Yanacocha’s Gold Mill facility located in northern Peru. The Gold Mill was commissioned in March 2008 with a 32’ x 32’ EGL, 16.5MW single stage SAG mill, to process 5 million tonnes per annum high grade oxide Au/Ag ore. Operational control, feed size distribution, grinding media, mill liner, grate and pulp lifter optimisation have allowed the mill to operate 15-30% above design throughput rates, but with a product P80 coarser than design. As part of the optimization, full grinding circuit surveys were conducted. Historical operating data and survey data were analyzed and used to evaluate possible circuit changes and determine alternative operating strategies. A number of changes were implemented which allowed the SAG mill to operate similarly to a large ball mill and achieve finer mill product that was closer to design. This paper summarizes life to date data analysis and improvements made by Minera Yanacocha as well as the grinding circuit optimisation study conducted by Metso Process Technology and Innovation.

Jan 1, 2012

By C. H. Hopper, D. R. Derry, H. S. McGowan

"The property of Matachewan Consolidated Mines is in the Matachewan area on the west side of Montreal river. It lies in the western extension of the Kirkland Lake sedimentary belt. The first discovery of gold on the property was made by S. Otisse, in 1916. The property was taken over by Ventures, Limited, in 1933 and production commenced in late 1934. To date (December 31st, 1947) it has amounted to 2,308,800 tons, from which gold and silver to the value of $9,567,600 has been recovered. The mill is currently treating 650 tons of ore a day.GENERAL GEOLOGYThe deposits lie close to the south contact of a belt of sediments striking in a general east-west direction. The sediments, presumed to be of Timiskaming age, consist of light buff arkose and greywacke, containing small pebbles. The Keewatin volcanic rocks to the south are andesites or basalts with cuff and agglomerate bands developed especially near the contact with the sediments. The lavas and sediments are overlain by relatively flat-lying sediments of the Cobalt series to the south and west of the mine, but these later sediments are not involved in the mineralization under discussion. The Keewatin lavas and Timiskaming sediments are intruded by dykes and lenses of red syenite porphyry that have approximately the same strike and dip as the invaded rocks. Later diabase dykes, apparently post-ore, run in a north-south direction and cut all rocks except the Cobalt series.OREBODIESThe gold-bearing mineralization forms bodies of two different types: (1) Within the volcanic rocks irregular orebodies with limited vertical extent. These consist of a series of flat-dipping quartz stringers and adjacent lavas and /or cuffs fractured, bleached, and mineralized with pyrite and gold. They are higher grade than the second type (average about 0.16 oz. gold a ton) and formed the main source of ore for the first 5 years of production. They are described in more detail than can be given here in an article by C. H. Hopper (4). More recent work on deeper levels has failed so far to find orebodies of comparable grade, though low-grade mineralization of a similar type does occur on the projected rake of the main group of the 'basalt type' of orebodies."

Jan 1, 1954

By Graham Swan

The case is presented for the development of a spray-on liner for ground support, but only in the context of a new mining system, consistent with the technical and business case advantages of liners compared to alternatives. Over the past 10 years much effort has been expended in specifying and testing the mechanical/environmental properties of various liners, without actually fulfilling any mining system requirements. The results have been generally disappointing, with no consistent and sustained application in a dayto- day production environment being achieved, anywhere. Central to this shortcoming has been the failure of mining/liner ma nufacturing companies to realise that screen/mesh or shotcrete cannot simply be replaced with thin, deformable liners: success will depend upon closely defining and evolving a new, liner- functional mining system. The paper begins with a discussion of some fundamental technical capabilities and constraints associated with 3M Canada?s liner material that has been developed in partnership with Falconbridge Limited. Intended applications for this liner include the support of bursting ground associated with deep mining conditions. With safe application and consistent performance in mind, the paper argues for a new mining system that derives in the first place from best quality drilling and blasting practices. Taking this as a given, a system for waterscaling and liner application prior to mucking out is proposed, followed by bolting through the liner while arranging for the bolts to be explicitly connected to the liner. Some logistical and equipment related challenges of such a mining system are then reviewed and discussed in the context of the business case for liners. It is concluded that this approach, if successful, will provide the greatest benefits in the areas of safer mining, due to reduction in worker exposure, and in reduced mining cycle times.

May 1, 2003

By I. Lazaro Roche, J. Brunner, J. Busto, X. Martin, J. B. Decitre, S. Gaffet, F. Hivert

"Muon tomography allows investigating the subsurface. Muons being penetrative, the attenuation of the muon flux depends on the quantity of matter the particles travel through, hence on the rock density and thickness. For the Temporal Tomography of rock Density using Muon Measurements (T2DM2) project, the muon flux measurements are performed in LSBB URL (http://www.lsbb.eu) in order to study the hydrogeological processes in the unsaturated area of Fontaine-de-Vaucluse karst aquifer. The suitability of the muography for this study is here numerically demonstrated. In parallel to these simulations, muon flux measurements are carried out in the LSBB galleries by means of a set of four scintillator tanks and Micromegas detectors are developed. These detectors, here described, are adapted for underground and confined spaces as well as other environments. Their performances are particularly interesting and should contribute to the expansion of muon tomography in new application fields. INTRODUCTIONMuon tomography or muography is a method to image large volumes by measuring the absorption of cosmic ray muons. It uses, in a passive way, a natural radiation source: the muons which are charged particles produced in the atmosphere. Primary cosmic rays interact with atmospheric nuclei and produce a huge number of secondary particles, including muons. Due to their important mass compared to electrons, they are highly penetrating, reaching several hundreds of meters below the surface. Their attenuation depends on the quantity of matter they cross. That's why they are used to investigate the subsurface, muon absorption measurement allowing to estimate the in-situ density of the rock.Georges (Georges, 1955) proposed in 1955 to use the muons in order to study the density variations caused by the overburden over an Australian tunnel. In 1970, Alvarez (Alvarez, 1970) imaged the internal structure of Chephren Pyramid thanks to this method. The muon tomography has been particularly developed for volcanology (Nagamine, 1995; Tanaka, 2007; Lesparre, 2010; Carloganu, 2013) over the last twenty years. Since the beginning of the 2010's, a growing amount of projects that proposed to use the muons in various fields get underway: the CO2 storage (Kudryavtsev, 2012), the exploration of Mars (Kedar, 2013), etc."

Jan 1, 2015

By Chunfeng Zhao, Chong Bao, Cheng Zhao, Jiashen Tian, Matsuda Hiroshi

"Based on digital image correlation (DIC) method and self-developed code, the global strain field changing and failure properties of rock-like materials with pre-existing double flaws are experimentally studied under uniaxial compression. By theoretical analysis with linear elastic fracture mechanics (LEFM), the strain approach proves to be practicable to investigate cracking process. Thus, two types of process zone are defined to discuss the specimen’s coalescence evolution at different loading stages. Crack initiation, propagation, and coalescence is a process of zone development and nucleation. DIC strain field results are studied on a meso-level using a strain approach. In the shear coalescence mode, the SPZ (shear process zone) in a bridge area coalesces with each other, while the TPZ (tensile process zone) grows independently. In general, the paper tries to establish the link between microscopic mechanical mechanisms and macroscopic mechanical responses in flawed rock. Further research should be done to study the cracking process and its effect on rock strength in detail by the DIC method.INTRODUCTIONNatural rock contains discontinuities including pores, fractures, inclusions or other defects. The existence of these discontinuities in the rock can decrease the strength and stiffness of the rock and they are a source of initiation of new discontinuities which may in turn propagate and link with other cracks and further decrease the strength and the stiffness of the rock (Sagong & Bobet, 2002). Lots of theoretical, experimental and numerical researches have been done in studying crack initiation, propagation and coalescence in rocks (Hoek & Bieniawski, 1965; Kranz, 1983; Reyes & Einstein, 1991; Park & Bobet, 2009; Gonçalves & Einstein, 2013). But when it comes to multiple pre-flaws, the issue that how the preexisting flaws affect each other becomes complicated and uncertain. The stress field around the tips of flaw can either enhance the impact of single flaw or weaken it. According to the observations have been done before, it is found that the way and function in which these cracks propagate and coalescence depends on the geometric arrangements (Bobet, 1997; Bobet & Einstein, 1998; Wong & Chau, 2001)."

Jan 1, 2015

By R. D. MacEchern, M. C. Rockwell

"This paper describes the research and tests carried out to recover the readily available barite from the tailings produced by the Nystone Chemical Ltd. operation at Debert, N.S. The tailings comprised 70-80% of the original feed and contained about 20-25% Baso4 .The objective of the research, undertaken during 1982, was to produce a barite concentrate which would meet the American Petroleum Institute (API) barite requirements for use in drilling mud. Samples from the tailings pond were examined and analysed to determine the tailings characteristics.Preliminary test work was performed on the tailings samples using a Haultain Superpanner, Wilfley tables and Humphrey's spirals. The grade of the barite concentrate retrieved did not satisfy the API barite requirements.The fineness of the tailings and the fact that approximately 80% of the barite was contained in the -200 mesh (0.074 mm) size fractions, indicated that flotation of barite from the tailings might be successful."

Jan 1, 1984

By Michel Noël

This paper presents a partial compilation of adopted measures of waste rock dump closures at mine sites located in Canada and Alaska, where the climate includes cold winters. The paper also presents the selection process that was followed for some of those mine sites. Mining operations usually generate waste rock that can sometimes result in very large quantities. Additionally, the nature of the ore body and the host rock will often introduce environmental impacts. These impacts need to be managed not only during the operations but also in the long term. Mine closure plans consequently have to address the long term issues that sometimes require perpetual treatment. Closure planning often involves the evaluation of risks associated with environmental and financial liabilities. It needs to consider the science, some common definition of objectives, and there will be a need to manage resources and schedules. Closure planning is essentially an exercise in constrained decision making. A performance and risk based ranking matrix is often developed during this selection process to identify the preferred option(s). The case studies presented in this paper provides a few examples. The level of knowledge on acid rock drainage from waste rock dumps has increased considerably over the past decades. It did not necessarily increase the level of complexity of the adopted closure methods, as the selected closure methods are often kept simple. A common approach consists of stabilising the slopes of the waste rock dumps material by resloping and then covering the waste rock with a growth media to support vegetation. Such covers prevent direct contact of animals with the waste rock material, minimise erosion and reduce infiltration to various degrees. The inclusion of water treatment is obviously dependent on the water quality being released.

Nov 1, 2008