Search Documents

By François Robert

The rate of new mineral discoveries in Canada has been declining in the last two decades. In response to the challenge and to stagnating investments in mining-related R&D, twenty Industry partners, supported by PDAC and Natural Resources Canada, established in 2010 the Exploration Innovation Consortium (EIC). This Consortium seeks to promote the discovery of new resources in Canada through coordination and sponsorship of industry-focused innovative and collaborative research and technology development, as well as training and education in mineral exploration. The two main themes of the integrated R&D program focus on exploration targeting in Deep and Mature Environments and in Remote and Covered Terranes.

May 1, 2011

"In mills, metallurgical efficiency is important in every step of the operation through to the tails. Different problems which hinder metallurgical efficiency exist in different mills. One such problem occurred in the Bralorne mill at the tailings end of the circuit, where the washing efficiency of the filters was so low that serious losses in dissolved gold occurred.The new cyanide plant at Bralorne went on stream in August 1961. Test work done showed that: a flowsheet of grinding in water, jigging, thickening, agitating, followed by double filtration, gave satisfactory results and was more economical than a counter current plant. Two filters, 141 x 161, with approximately 700 square feet of filtering surface on each, were purchased and installed in series. Test work showed that this was ample filtering area for 500 tons per day.When the plant started up a density of 45% solids was maintained in the agitators, and a 20 ounce cotton dl1ck was used on the filters. Vacuum was between 23 - 25 inches. Under these conditions the filters would not work and only picked up a very slight skim of pulp. Various speeds were experimented with, 4 minutes per revolution being the most efficient. At this speed the thickness of the pulp on the filters increased to about 1/8”• It was therefore quite apparent that, under these conditions, the filters would not handle very much tonnage and the mill tonnage would have to be reduced drastically until the problem was solved."

Jan 1, 1967

By Tom Setterfield

Monster Copper Resources ?Junior focused solely on IOCG deposits ?Founded by ex-WMC geoscientists ?Properties in Brazil, Wernecke Breccias (Yukon), Central Mineral Belt and Nova Scotia Nova Scotia ?JV with Wallbridge Mining Company ?Ongoing Story ?Presented as a case study in generation and implementation of IOCG exploration program

Apr 1, 2005

By G. W. Davies

"IntroductionThe development of British Columbia's northeast coal deposits, represents the single biggest industrial undertaking in British Columbia's history.As a result of this development, several thousand jobs were created, hundreds of millions of dollars in new tax revenue and billions of dollars in new foreign exchange began flowing into Canada.The Northeast Coal Development began in 1981 with the signing of sales contracts to ship a total of 6.5 million tonnes of metallurgical and additional quantities of thermal coal annually to Japan over a 15-year period. The current long-term agreements contain provisions for extension to 20 years.The sales contracts with a group of Japanese steel mills were signed by two Vancouver-based mining companies, Quintette Coal Limited and Teck Corporation. The agreements followed years of exploration and negotiation beginning in 1968.The first shipment of coal from Quintette and Teck's Bullrnoose Mine was transported by BC Rail and Canadian National Railways to the Ridley Island coal port in the fall of 1983."

Jan 1, 1992

By Lauri Gregg

How Can Man Meet the Carbon-Free Energy Challenge ? ? Increases in Energy Efficiency can displace 1/2 to 2/3 of the Carbon-Free Energy required to stabilize at 550 ppmv ? Renewable Energies require too much land and thus can displace 5 to 10 % of the energy requirement ? Large new sources of carbon free energy are needed ? Conservation is desirable but provides only a small and variable contribution ? People will have to adjust to higher levels of CO2 in the atmosphere as energy demand continues to grow

Nov 1, 2002

By K. A. Lewandowski

Agglomeration of ore used in heap leaching allows for the immobilization of fine particles that would otherwise migrate and cause permeability problems in the heaps. For copper ore, binders are needed in order to make stable agglomerates. However, the majority of binders break down when introduced to an acidic environment, allowing fine particles to be released from the agglomerate surfaces. These particles migrate through the heap impeding solution flow, leading to a decrease in metal recovery rates. The authors have developed a series of testing procedures to determine the acid resistance of several binders. Only five binders were shown to be acid resistant in soak tests, decreasing fines migration by up to 93%, compared to tests which were agglomerated with leach solution, raffinate, as a binder. Flooded percolation column testing also showed that these binders were able to reduce the "slump" of the ore by up to 82% and increased the hydraulic conductivity by up to 90%, when compared to agglomerating with leach solution alone. The use of binders in the agglomeration of copper ore also showed no negative effects on the bacterial populations throughout a leach cycle.

Jan 1, 2007

By D. Embury

The construction and utilization of oil and gas pipelines is a vital aspect of the Canadian economy. The evolution of materials for this application can be considered as part of an evolutionary process in which the processing of the materials is linked to the design requirements of the pipeline. The evolution of both materials and designs will be considered in terms of parameters such as yield strength, work hardening characteristics including strain path changes such as the Bauschinger Effect and toughness. The final portion of the presentation will consider the possible uses of non-metallic materials, composites and 'smart 'systems in pipeline construction.

Jan 1, 2005

By Robert B. Parsons

"Ontario and Quebec taxpayers will have to dig deeper into their pockets to pay more tax, according to budget papers tabled in these provinces in May 1993. Individuals will be hardest hit, but corporations will also have to ante up in the face of higher rates, reduced deductions, and new taxes.Up, up, and away...Somewhere in the bleak picture of the 1993 Quebec and Ontario budgets, there is a bit of good news for the mining industry.Careful scrutiny reveals:• Ontario will correct a capital tax provision which inadvertently penalizes flow through share issuers;• Quebec's flow-through incentives will be extended to December 31, 1995; and • both Quebec and Ontario will allow deductions for mine site reclamation payments.The industry may also find some comfort in the fact that Ontario's new corporate minimum tax will be profit-based (unlike the federal minimum tax), so that non-producers should not face a liability for this tax. There is some concern though, about Quebec's announcement that the refundable credit mechanism in the Mining Duties Act will be reviewed."

Jan 1, 1993

By S. W. Brooksbank, R. A. Benkis

"IntroductionThe Republic of Indonesia is a developing Southeast Asian country that unites the Indian and Pacific oceans, and spreads across nearly 14000 islands with a total land area of about two million km-. The distance across the country approximates the distance across Canada: Indonesia extends for more than 6000 km from the northern tip of Sumatra to the eastern border of Irian Jaya in the middle of New Guinea. With a population of around 180million, Indonesia is one of the world's most populous countries. A mix of 366 ethnic groups populates the country and there are some 250 distinct languages spoken. The topography of Indonesia generally is quite rugged because of its numerous volcanos. For example, the island of Java has 121 volcanos, of which 15 rise above 3000 m and another 44 reach heights between 2000 m and 3000 m.Indonesia has a diversified resource base, with plentiful energy resources (coal, oil, gas and hydroelectric), significant mineral deposits, large timber potential and a developed system of agricultural commodity production and export. A high proportion of the primary resources are on the sparsely populated islands of Sumatra and Kalimantan, whereas 7'3 of Indonesia's people reside on Java, or on 70/0 of the country's land area. Around Jakarta in western Java the population density is around 8000 per krn2. This contrasts with less than nine people per km- on Sulawesi (Fig. I)."

Jan 1, 1992

By Bertrand Quiniou, Pierre Amadieu

Ion exchange technologies and processes are proven and established technologies widely used in numerous industries including hydrometallurgy for metal separation and recovery from metal bearing solutions. They have evolved through innovation which includes the development of countercurrent multistage (or multivessel) ion-exchange contactor systems with the benefit, for industrial operations, of greatly reduced footprints and ion-exchange media inventories, as compared to more traditional fixed bed contactor systems. Information on procedures for design and sizing of countercurrent multistage ion-exchange contactor systems is not readily available since it is most often proprietary know-how. The purpose of the present work is to develop a simple and innovative approach for the sizing and modeling of industrial countercurrent multistage ion-exchange contactor systems. The suggested approach builds upon published results and upon the following observation: in an industrial setting, knowledge of how component concentration or load on a contactor output streams vary with time t within a cycle duration (0 < t < T) is generally of little interest, only knowledge of time average of such concentration or load over a cycle duration T is sought for. The presented approach will be tested against current or past performances of industrial countercurrent multistage contactors of Orano Mining operations such as SNK‑3M moving packed bed contactors in Kazakhstan and NIMCIX fluidized bed contactors in Namibia.

Jan 1, 2020

By Kiran B. Chaudhuri, Michael Koch, Jorg Lema Patino

"Stricter pollution regulations together with other factors have stimulated interest in the modernization of the traditional sinter - blast-furnace lead operation. In this context, direct smelting methods have again come into prominence. Consequently, the Kivcet Lead Smelting Process, which belongs to this group, has attracted the attention of the lead producers of the world. The Kivcet Process offers the advantage that lead and zinc can be simultaneously recovered in a single furnace unit. KHD Humboldt Wedag A G, Koln, Federal Republic of Germany, has signed a contract with the Sociedad Complejo Metalurgico de Karachipampa of Bolivia for the delivery of a turn-key Kivcet plant, which is expected to be the first plant of its kind in commercial operation. This paper describes the design and expected operating data of the plant."

Jan 1, 1980

By P. Cielo

"Nondestructive inspection is an important quality control tool in the material processing industry. Being nondestructive, such a control may be applied to the whole production, as long as the available techniques are fast and easily automated. Ideally, nondestructive testing (NDT) methods should operate in a noncontact configuration in order to be deployable on-line with minimum perturbation of the production process.After a short introduction to the most common NDT techniques, with particular emphasis on ultrasonic, radiographic and electromagnetic methods, a few new approaches which are under development at the Industrial Materials Research Institute, (Boucherville, Quebec), are reviewed. Noncontact techniques such as laser ultrasound, thermoelastic and thermographic methodologies will be described, and their applications to materials of industrial interest will be discussed."

Jan 1, 1989

By M. Behrouz

Thermal power plants convert thermal energy due to nuclear reactions or the combustion of coal, gas, heavy oil, or some other hydrocarbon to electrical energy. They consist of a variety of equipment, such as boilers, turbines, generators, cooling towers, and auxiliary equipment. Any factor that affects the equipment efficiency affects the overall efficiency. Analysis of the cooling tower and raw water using the Langlier Saturation and Ryznar Stability Indices showed that the cooling water at Sarchesmeh was slightly scaling with respect to silica. Cold lime softening was found to be a cost-effective method to produce cooling water with adequate properties to reduce the cooling water make up from 85 to 70 m3/h and blow down rate from 35 to 20 m3/h.

Jan 1, 2007

By Carol Odell

This paper was prepared as a brief for Prospectors and Developers Association of Canada (PDAC) to guide input at a series of round tables carried out by the Federal Government in response to the 38th Standing Committee on Foreign Affairs and International Trade (SCFAIT) report, on ?Mining in Developing Countries and Corporate Social Responsibility?. This document mandate is to provide background information, analysis and recommendations on the practice of Canadian exploration and mining companies abroad. This research was based on 11 case studies of Canadian companies which have experienced conflicts or controversies overseas. All case studies were assembled through an extensive literature review of publicly available documentation and communications with representatives of the mining companies to assist in deepening the insights into the drivers of the conflicts and the needs of Canadian companies in similar situations. The case studies include both exploration and mining operations. Our analysis begins with the identification of general and case specific drivers of conflict/controversy in each case study. Company names are kept confidential and only anonymous results are presented. We make ample use of simple flow charts and schematic diagrams to explain how contextual drivers and aggravators and company drivers and mitigators play varied and interrelated roles in conflicts. The diagrams also illustrate the cumulative analysis of drivers including the linkages among drivers/aggravators/mitigators across different domains (social, governance, NGO/media and company). Finally, we discuss needs of companies and propose recommendations for addressing social responsibility and human rights concerns.

May 1, 2007

By Roy Sage

Overview ? History ? background to current programs ? Kyoto status ? Support for technology development ? Support for GHG reduction ? Sources of information History ? 1988 - Toronto Conference - The Changing Atmosphere ? Proposed target ? CO2 levels reduced to 20% of 1988 levels by the year 2005 ? 1992 - Canada signed Framework Convention on Climate Change at the UN Conference on Environment and Development in Rio de Janeiro in June 1992 ? Canada launched the National Action Plan on Climate Change ? Kyoto protocol adopted in principle in 1997

Nov 1, 2002

By Jeffrey S. Loen

"Abstract - The size, morphology, surface texture, per cent mineral inclusions, and bulk chemistry (Ag and trace elements) of placer gold particles vary systematically according to transport distance from source rocks, as indicated by a case study from the Pioneer district in Montana, and data from the literature.Placer gold samples show a rapid decrease in mean and maximum particle length, and a gradual increase in flatness index (F.I. = length + breadth/2 X thickness) from about F.I. = 2 in bedrock deposits, to as much as F.I. = 45 over transport distances of several tens of kilometers. Primary mineral inclusions (mainly quartz, sulfide minerals, and iron oxides) are mostly lost within 10 km to 20 km of fluvial transport; this loss of quartz and trace metals causes a major change in bulk chemistry of placer gold samples. Following the loss of inclusions and the development of flakes, edges of flakes are folded and the mean number of folded edges in a sample increases with distance. When viewed under the electron microscope, surface textures of placer gold particles also become progressively more pitted with distance.Analysis of placer gold particles can be used to help evaluate placer source-area problems (placers with no known hard-rock gold deposits). For example, coarse placer gold containing abundant inclusions indicates a proximal source. On the other hand, an abundance of thin flakes is evidence of a long transport distance and possible reworking from older gravels. Placer gold characteristics can therefore provide information on distance to mineralized source rocks."

Jan 1, 1995

By Jeffrey S. Loen

"The size, morphology, surface texture, per cent mineral inclusions, and bulk chemistry (Ag and trace elements) of placer gold particles vary systematically according to transport distance from source rocks, as indicated by a case study from the Pioneer district in Montana, and data from the literature.Placer gold samples show a rapid decrease in mean and maximum particle length, and a gradual increase in flatness index (F.I. = length + breadth/2 x thickness) from about F.I. = 2 in bedrock deposits, to as much as F.I. = 45 over transport distances of several tens of kilometers. Primary mineral inclusions (mainly quartz, sulfide minerals, and iron oxides) are mostly lost within 10 km to 20 km of fluvial transport; this loss of quartz and trace metals causes a major change in bulk chemistry of placer gold samples. Following the loss of inclusions and the development of flakes, edges of flakes are folded and the mean number of folded edges in a sample increases with distance. When viewed under the electron microscope, surface textures of placer gold particles also become progressively more pitted with distance.Analysis of placer gold particles can be used to help evaluate placer source-area problems (placers with no known hard-rock gold deposits). For example, coarse placer gold containing abundant inclusions indicates a proximal source. On the other hand, an abundance of thin flakes is evidence of a long transport distance and possible reworking from older gravels. Placer gold characteristics can therefore provide information on distance to mineralized source rocks."

Jan 1, 1995

The 2-4D window shown above is the base startup window which allows you to begin a new project. ??Setting up the project is the first step ??The next step is to setup the properties to be used in this project

Feb 1, 2008

By T. R. C. Aston, C. M. K. Yuen, J. L. Gilby

"The access tunnels for the Donkin-Morien Mine in Cape Breton, Nova Scotia, comprise two parallel tunnels driven through a sedimentary sequence of sandstone, siltstone and mudstone to intersect the Harbour Coal Seam under the Atlantic Ocean, approximately 3.5 km offshore (Fig. 1). The No. 2 tunnel was driven a total distance of 3579 m using a 7.6 m diameter Loyat full-face tunnel boring machine (TBM) and was supported by steel sets. The No. 3 tunnel was initially driven a distance of 1027 m using drill and blast methods (dimensions 7.6 m wide by 5.3 m high) supported by rock bolts and shotcrete. This tunnel was then completed (front March 1986 to February 1987) using the tunnel boring machine to a distance of 3573 m.During the period May 1983 to December 1984, a major geotechnical research program was undertaken in the Donkin-Morien tunnels by Golder Associates in conjunction w,ith CANMET and the Cape Breton Development Corporation (Yuen et al., 1985). The research program included the monitoring of the performance of the TBM and drill and blast drivages, and the study of the thrusting characteristics and rock-interaction of the TBM excavation. The main emphasis of the research program was on the collection of field data which was to be made available in the form of a comprehensive report for the future use of others who might wish to carry out a detailed interpretation and analysis. The information gained from the program was also used during the tunnel"

Jan 1, 1988

By Peter McGoldrick

This Talk ?Australian deposits in world context ?Geological setting: the importance of the basin fill ?Key deposit features using HYC (McArthur River) and Century as examples ?The difference between Aussies & Canuuks(that is between Australian & Canadian sedexdeposits!) ?Timing of mineralization ?Sources for metals and ore fluids ?What makes a super giant sedexdeposit?

May 1, 2006