Search Documents

By Joseph J. Larry

In hard siliceous sandstone strata overlying coal seams, roof bolting is often the bottleneck in the coal production cycle. In the past, these strata have been drilled by pneumatically operated stopers. Although slow drilling is cumbersome and uncomfortably noisy, the stoper was the most effective drill in these harder strata. However, because of the (U.S.) Coal Mining Safety Act, which limits noise levels for operating drills, FMC Mining Equipment developed the water-through-the-drill-steel method of drilling high-compressive-strength strata. Although water-through-the-drill steel had been developed earlier, the real impact of wet drilling techniques surfaced when the dual-boom roof drilling machines were installed at the Virginia-Pocahontas Division, Keen Mountain, Virginia, in 1974. This paper covers some of the technical details of the water-through- the-drill-steel design and its application.

Jan 1, 1979

By E. Lee Cameron

The old mine workings on four barite-fluorite veins of the Lake Ainslie district, Nova Scotia, were opened recently and channel sampled. The samples were then forwarded to the Ore Dressing Laboratories, Bureau of Mines, Ottawa, for chemical analyses. Following the analyses, the sample rejects were combined to form bulk samples, representing ore from each vein, for small-scale batch test work. Tonnage samples from the veins, for pilot mill testing, were submitted when requested by the Bureau. The results of the analyses on the channel samples showed that there are two grades of ore in the di strict, represented, for test purposes, by the Trout River vein and Johnson vein ores. Small-scale and pilot-plant test work was undertaken on both these ores. The Trout River ore is amenable co concentration but, because of the high-barite-co-fluorite-co-calcite ratio, a fluorite concentrate was not obtainable from the Johnson vein ore as received. However, Johnson ore blended in a 1 :1 ratio with Trout River ore gave a mill feed that was readily concentrated. The test work on these ores showed that the following concentrates are obtainable : (a) A barite concentrate, with a recovery of 85 to 95 per cent of the available barite, analysing 93 co 96 per cent BaS04, 4 co 6 per cent CaF,, and 0.5 co 2 per cent CaCO3. (b) A fluorite concentrate, with a recovery of 80 co 85 per cent of the available fluorite, analysing 94 to 97 per cent CaF, , 1 to 3 per cent BaSO., and 1 to 3 per cent CaCO3

Jan 1, 1945

By Alim Ullah

Danieli entered into the Direct Reduction (DR) field in order to offer its clients complete turnkey facilities for steelmaking?from processing of raw materials through finished products. The Danarex® Process produces a passivated product, called the Supermetallic (SPM), without hot-briquetting. One of the main features of the Danarex® Process is its ability to produce approximately 50% of the Direct Reduced Iron (DRI) through reduction gas generated in a reformer and another 50% through recycling preheated furnace exit gas. Some other distinguishing features are: separation of carburising and cooling zones and the use of double bustle for better distribution of gas inside the shaft furnace. A pilot plant was set up at Hazen Research, Inc., Golden, CO in order to show that the integrated process works as expected and to obtain process data. The SPM obtained was of a very high quality, evidenced by metallization levels of 92% to 98%. The carbon content could be controlled between 1.5% to 4.0% by varying the operating conditions and approximately 75% of this carbon was present as Fe3C. The product was tested for inertness by Chilworth Technology, England, using UN standard tests and was found to be safe for outdoor storage and transportation.

May 1, 2003

By Collin Bartlett, H. Storch

"Modern metallurgical processes operating with oxygen enriched air, such as the Outotec Flash Smelter and Flash Converter, generate very concentrated SO2 off-gas, which in combination with Outotec sulphuric acid plant technology allows the production of high pressure steam to be used for power generation. Outotec combines well proven technology of sulphur burning plants for this purpose with metallurgical plants.The application of Outotec’s proven LURECTM process enables processing of SO2 gas of up to 25 vol.-%. This process maximizes the energy recovery from the SO2 oxidation at a suitable high temperature level which can be turned into high pressure steam. The application of the Outotec HEROSTM heat recovery system enables the generation of low pressure steam from the absorption energy released at the intermediate absorption step. Additionally, energy is also recovered in the acid coolers for boiler feedwater pre-heating.The concept of integration of high and low pressure steam in combination with the pressurized operation of the boiler feedwater deaerator, thus heating up the boiler feed water to temperatures around 160…170°C, enables indirect transfer of low pressure steam (for deaerator operation) into more valuable high pressure steam, which improves the degree of heat recovery. This is the characteristic of Outotec’s HEROS+TM process.The increased generation of high pressure steam will in turn enable the generation of more electricity when compared to a standard traditional sulphuric acid process."

Jan 1, 2014

By H. Tetu, F. Pells

"The copper-molybdenum property of Brenda Mines Limited is located in the Okanagan district of British Columbia, approximately 25 miles west of Kelowna. The Okanagan Valley is a resort and fruit-growing area, and therefore pollution control measures are more stringent than in some remote areas.The Brenda plant began production in April 1970 and is operated at a rate of 24,000 tons per day. The plant site is located at an elevation of 4,800 feet, which is approximately 3,600 feet above the level of Okanagan Lake. The site is in the Okanagan drainage basin.The major consideration in the design of the system was the prohibition of any downstream discharge. It was therefore necessary to redaim as much water as possible and to minimize the addition of fresh water to the system. The maintenance of a water balance is of critical importance.This paper will outline the major design criteria for the systems and the site investigations which were carried out. The design and construction of the facilities will be de-scribed and current operating experience will be outlined."

Jan 1, 1971

By Dean Millar

Clean, green, cheap compressed air can be produced efficiently and renewably by modernization of a 19th century technology ?The hydraulic air compressor has no moving parts ?After commissioning, the Ragged Chutes HAC operated for 70 years, only being stopped twice for repairs to the intake heads ?Operates using hydropower from Montreal river ?Produced air for ~29 silver mines in Cobalt, 20 km distant

May 1, 2013

By L. K. Daneshmend

"Competitive pressures dictate that the mining industry moves to larger mobile underground haulage equipment with more advanced equipment mechanization, higher levels of autonomous operation of machines, and longer periods between access by maintenance personnel. Since such new machines will of necessity be more complex than existing designs, machine reliability has become a key issue in progressing toward advanced mobile underground haulage equipment. Reliability and maintainability models of such equipment are practically non-existent in the literature. This paper addresses the issue of reliability and maintainability of mobile underground haulage equipment on two fronts: reliability modelling to enhance decision making for maintenance planning; and reliability simulation to enable evaluation of more rigorous production planning scenarios. A case study from a gold mine in the Chilean Andes is presented, for which reliability models of mobile underground haulage equipment, specifically load-hauldump vehicles and underground haul trucks, are developed, and a reliability-based simulation implemented. IntroductionMaintenance accounts for 20% to 35% of the overall operating budget for a typical underground operation, and hence represents the largest portion of the mine’s controllable operating costs (Cutifani et al., 1996; Campbell, 1997; Goddard, 1998). This, coupled with the fact that industry today is faced with an ever more complex and demanding marketplace, has led to an increasing interest in methods to reduce maintenance costs.Although significant effort has gone into developing effective maintenance strategies for industry in general, application of these to the"

Jan 1, 2003

By R. E. Ray

"As real estate for new development in urban settings becomes scarce, commercial high rises are being constructed above open passenger rail tracks and vehicular roadways. Rail and roadway overbuilds are treated as tunnels requiring emergency ventilation systems for train or automobile and truck fires. The value of floor space in residential and office towers poses challenges to engineers responsible for designing fan rooms and shafts for tunnel ventilation systems within the towers. This paper describes a case study of the unique incorporation of tunnel ventilation fan plants in the overbuild structure of a passenger railyard and an adjacent roadway.INTRODUCTIONTunnel ventilation systems are required for passenger rail and transit (subway) tunnels by the NFPA 130 Standard for Fixed Guideway Transit and Passenger Rail Systems, and the NFPA 502 Standard for Road Tunnels, Bridges, and Other Limited Access Highways requires tunnel ventilation systems for vehicular (road) tunnels. Passenger rail and transit (subway) tunnels are typically ventilated with a series of shafts placed longitudinally along the tunnels to provide piston relief for normal train operations and emergency ventilation of train fires utilizing reversible axial flow fans. The shafts are incorporated in dedicated ventilation buildings that house the tunnel ventilation fans and starters, switchgear to power the fans and other equipment and systems in the building, Programmable Logic Controllers (PLCs) to control fan operation with Supervisory Control and Data Acquisition (SCADA) software, and HVAC fans and ductwork to ventilate the spaces in the building. These ventilation buildings may also provide access to the tunnels below with ingress/egress stairs for use by first responders and firefighters entering the tunnels and train or transit system passengers exiting the tunnels in an emergency. A photograph of a passenger rail ventilation building that encompasses four tunnels is shown in Figure 1."

Jan 1, 2019

By B. T. Lu

The corrosion and wear properties of a series of chrome white iron (CWI) castings were study using electrochemical and low-stress sliding abrasion tests. The results confirm that the corrosion resistance of these materials is largely dependant on the quantity of chromium in the matrix, while the wear resistance is mainly controlled by the volume fraction of chromium carbides. A pseudo-wear/corrosion map is developed to identify alloy compositions that may be suited for erosion/corrosion conditions.

Jan 1, 2005

By S. H. Ward

An account of a new method of investigating the electrical .properties J the earth's crust is presented. The method, called AFMAG, employs, as a source, natural alternating magnetic fields of audio and sub-audio frequencies. Measurements of the distortion of these fields caused by geological features are made with the aid of search coil detectors at several discrete frequencies. Many results of field surveys made with the method are presented and they illustrate its advantages and limitations when applied to the search for massive sulphide mineralization. The advantages far outweigh the limitations and in fact indicate that a major breakthrough in geophysical exploration technique and instrumentation has been made.

Jan 1, 1958

By R. H. McCorkell

Radon emanation rates. J. and compositions of materials from the Canadian Certified Reference Materials Project (CCRMP) indicate that the fraction of the Rn produced that escapes, E, is usually 1% to 8% and the 238U decay chain is nearly in secular equilibrium. For some Chinese ore standards, E values are higher than f or the CCRMP materials. Standard ore tailings have 2/oPb concentrations higher than expected from their 226Ra concentrations and Rn escape rates (12 - 34%) . Biological materials have E ˜100%, their ash E ˜0%. Pelletizing ore powders at 20 000 lb/in2 reduces J by only 20 - 40% but only 2% of Rn escapes from pressed Li2B4O7 pellets and 0.01 - 0.04% from fused Na2B4O7 or Li2B4O7 discs. Large, difficult-to-explain random variations in J are observed in some situations but several highly reproducible ways of measuring emanation rates have been found.

Jan 1, 1986

By G. M. Behrend

A group of mining men attending a recent workshop on "Analysis and Control in the Canadian Minerals Industry" issued, among others, the following statement: "Slurry flow measurement is considered to be one of the most inaccurate in the industry. A special program should be launched to encourage development." In response, this paper starts off the program with an investigation of the principles and the conventional practice of slurry flow measurement and identifies weaknesses which cause inaccuracies. Then it follows with descriptions of nonconventional systems in use at various locations and comments on their degree of success. The paper concludes that relatively simple methods, which it describes, can be applied to obtain an accurate slurry flow measurement.

Jan 1, 1973

By M. G. Dellow, D. W. Hendriks

"In early 1988 the decision was made by Noranda Minerals Inc. to install pressure filters at the GECO mill to replace the vacuum disk filters and bunker-C fired rotary kiln dryers. Two filters were installed, one for copper concentrate and one for zinc concentrate. Completion of the project was scheduled for the third quarter of 1989. The filters were made operational in October 1989. Some work remains to be done yet on loadout conveyors for total project completion. Capital expenditures for the project have been approximately $2,700,000 to date. The paper describes the selection criteria for the filter, the installation, startup and associated problems.1. INTRODUCTIONThe filter model chosen for the project was the Verti-Press model VP-50-6(7) (Figures1 ,2 and 3) by Filtra Systems of Farmington Michigan, USA. The decision to purchase the Filtra Systems filter was based on gaining familiarity with a different, mechanically simpler pressure filter than the Larox design and to a lesser extent a necessity for repairs to the the disc filter, rotary kiln dryer system used at the GECO operation for its' copper and zinc concentrates. The fact that it is manufactured in North America was an important consideration. The same basic principles of pressure filtration as the Larox machine are used but the implementation is quite different and somewhat simplified with some interesting innovations. 2 filters were installed to allow direct and immediate comparison of the same machine on both fine and coarse materials. Copper concentrate is reground for cleaning on the flotation circuit while zinc is not. Screen analysis of composited samples of concentrates for 1988 indicated that expected copper concentrate would be approximately 66% minus 400 mesh and zinc 50% minus 400 mesh (Tables 1 & 2).The filter is composed of six horizontal chamber module layered vertically and held together in a frame by 1 O large bolts; torqued down to 4000 ft-lbs. 6 individual belts are used; each with its own drive system. The belts themselves are of a 3 piece design with a filter cloth portion, a support belt and a rubberized intermediate portion. They are held together with steel clipper lacings. A basic description (1) of the filter operation is as follows. ""The horizontal filler chamber is closed by hydraulically pressurizing seals across each end of the filter chamber to 200 psi. The feed pump then pumps slurry into the filter chamber. Suspended solids are retained on the filter belt and the filtered solution drains into a lower drip tray and flows from the filter by gravity. At the end of the filtration or feed cycle, a rubber diaphragm in the filter chamber is pressurized hydraulically to 100 psi pressure. This removes all free liquid from the filter chamber and the filter cake. After the diaphragms are retracted the filter cake is blown with compressed air to remove any residual cake moisture. The seals are then retracted and the belt is advanced to discharge the filter cakes. During the cake discharge the belts are washed with a spray header located at the drive end of the filter. The belt assemblies move one (1) complete revolution during the cake discharge cycle. The cycle automatically repeats until the filter is shut down by the operator."

Jan 1, 1990

By Harold S. King

TWO summers ago I had the privilege of visiting No. 18 colliery at Glace Bay. Underground, we travelled along the haulage-way behind a powerful electric locomotive. The motor in this locomotive began to smoke badly and a carbon tetrachloride type of extinguisher was used several times during the trip. At the time, I noted a strong odour of phosgene. On my return to Sydney, I spoke to Mr. Harold Gordon, Assistant to the General Manager of the Dominion Steel and Coal Corporation, and warned him of the danger of using this type of fire extinguisher in confined spaces, since it is a well known chemical fact that phosgene, a dangerously toxic gas, is formed by the decomposition of carbon tetrachloride. This danger does not seem to be widely recognized, so it seems advisable that a more general warning be published. Attention was first drawn to the danger by the death of two men in the United States Navy Department subsequent to breathing fumes from carbon tetrachloride used in a fire, and when an employee of the Bureau of Mines also was overcome while fighting a fire with carbon tetrachloride liquid. These accidents led to an investigation of the decomposition products of carbon tetrachloride by a group of workers in the Research Laboratory of the Pittsburgh Experimental Station, U.S. Bureau of Mines, the results of which were published in the October, 1920, number of the Journal of the .Franklin Institute (1). Their experiments were conducted by two methods. The first consisted in applying the liquids to actual fires and -to hot metal in a closed room of 1,000 feet capacity, where the gaseous products, mixed with air, could be retained and analyzed. The second method was to pass the vapour:s in air through heated tubes of iron or quartz, where the humidity of the air and the temperature could be controlled.

Jan 1, 1939

By Pamela Paradis-Sokoloski, Deni Thibodeau, J. Denis, Samantha J. Espley, P. O’Donnell

"During the previous decade, the role of spray-on liners within the mining industry was limited to providing a corrosion resistant coating to screen and bolts; however, increasingly, liners are being used as ground support products. Expanding use and testing of liners have demonstrated their ground support function, yet the definitive support mechanism is still under debate. The most promising theory is the retain/hold/reinforcement concept (Kaiser et al.,1992). This conceptual theory has been the basis for the recent underground trials at INCO where, specifically, shotcrete and MIROC Mineguard were tested in two trials to further define limitations and applications of each liner.In a cursory overview, shotcrete is becoming accepted as a support product, while Mineguard is only slowly gaining acceptance.This discrepancy is the result of the corresponding life-spans within the industry, whereby shotcrete has had wide-spread use for decades, yet Mineguard has only recently been introduced. Currently at INCO, shotcrete is primarily used: to provide support in poor ground conditions, to add stability when developing through backfill, and to provide damage control in seismically active mines. It is also used to protect production headings and secondary-blasting chambers from fly-rock damage during blasting. Despite an obvious support function of the liner, shotcrete has always been used in addition to bolts and screen. Comparatively, Mineguard is still in the testing stage, where the greatest potential is increased productivity for applications in multi-tasking development headings. In this scenario, Mineguard provides instant support to replace screen, and bolts temporarily. When the heading has advanced, the drill and support crews work in tandem, drilling off the next round and installing bolts for long-term radial support, respectively. Other potential applications of Mineguard are within production headings to replace screen in the back, and screen and bolts in walls. The potential for both liners to replace conventional support is clearly war-ranted, such that defining the support role was the primary goal of the two underground trials."

Jan 1, 1996

By M. N. Collison

"In 1960, with the opening of the Chisel Lake mine near Snow Lake, Manitoba, the Hudson Bay Mining and Smelting Co., Limited, commenced a new phase in their mining operation -that of bringing ore to Flin Flon over 100 miles of railroad.The schedule of operations required to accomplish this, together with an outline of some of the problems of handling ore at 40° and 50,0 below zero, are discussed. The facilities required to thaw and unload from twenty to fifty cars per working day are also described."

Jan 1, 1966

By D. J. King

The development in recent years of a fluidized bed system for use as a counter-current solid ion exchange loading contactor for the purification and concentration of uranium from leach liquors has had a major impact on the design of uranium extraction plants. The main object of this paper is to describe many of the variations that can be applied to the design of uranium extraction plants arising from the use of a fluidized bed loading contactor with a view to providing a guide for the development of a flowsheet for a new uranium extraction plant. The paper has been devoted primarily to the consideration of conventional uranium extraction plants in which a ground ore is leached in mechanically or air agitated tanks. The effect of the use of a fluidized bed loading contactor on each of the plant sections from leach to uranium purification and concentration has been considered. In order to describe most effectively the impact of using a fluidized bed solid ion exchange loading contactor, its use has been compared with the performance that can be achieved with the most common alternative purification processes. The comparisons are made largely on a technical basis, but the effect on the capital and operating costs of the different uranium extraction flowsheets are described qualitatively. In making these comparisons, consideration is given to the effect on the size, number and materials of construction of equipment items and how the quantity and composition of the liquid effluents can be controlled to reduce the environmental problems arising from the disposal of these effluents. The paper also discusses some of the factors that should be taken into consideration in the design of a fluidized bed loading contactor and describes various designs of the elution section that can be used in conjunction with the loading contactor.

Jan 1, 1979

The Cadia mine is shifting from the open pit operation to the Cadia East underground block cave. The resulting increase in milled tonnes and the decrease in fines production through shifting to block caving require an increase of over 25% in installed power. This expansion is being accomplished via the installation of up-front crushing and HPGR milling of the ore, with the SAG mill receiving a secondary crushed feed. This design, criteria and rationale for selection is presented. Over the coming years, the mine will further expand capacity. The target is to accomplish this with minimal addition of installed power or use of fresh water. This presents a challenge that epitomizes the future constraints on our resource dependent and intensive industry. The approach and proposed options to this longer-term expansion are also presented.

Jan 1, 2012

By L. Price, R. Hortie

Movement of ore and waste from the Hilton Mines pit is accomplished by truck haulage. With the aim of reducing costs, a study of truck fleet replacement was initiated. The study included on-site short-term tests and longer-term rental purchase agreements for haulage trucks. The operation and maintenance characteristics of different trucks, along with projected haulage conditions, were used to prepare cash flows, from which the most advantageous trucks were selected. The results of the study and implementation of the recommendations gave a cost saving greater than had been estimated. The study also indicated areas where improvements could be made, and resulted in much more attention being paid to road conditions, the training of operators and mechanics, and the development of a practical preventative maintenance scheme.

Jan 1, 1971

By R. R. Montigny

A brief description is given of the history, location and geology of the Granisle Copper Limited operation on Copper I land in Babine Lake. Detailed information is given with regard to pit design, planning, drilling, blasting, excavation and haulage. Equipment maintenance and mining costs are also presented.

Jan 1, 1971