Search Documents

By R. K. Jonas

"Pressure leaching and pressure oxidation in autoclaves are important alternatives in the extractive processing of gold, copper and nickel ores. The application of advanced control to pressure leach and pressure oxidation autoclaves could achieve significant benefits as has been shown in alumina pressure leaching. This paper compares and contrasts alumina digestion autoclaves to other mining autoclaves with respect to advanced controls. The application of advanced control in alumina with over 30 units controlled worldwide, and its benefits will be reviewed. The design and potential benefits from advanced control for pressure oxidation and leaching will be presented.INTRODUCTIONIt is this author's position and the purpose of this paper to propose that advanced control could be effectively applied to autoclaves in the nickel, gold, and copper mining processes. This is based on the proven effectiveness of advanced control on autoclaves used in the alumina industry for pressure leaching of bauxite ores. Incremental, but significant increases in production could be realized by applying advanced control to autoclaves, as evidenced by the alumina industry, and this not being implemented in other autoclaves in the mining industry.In addition, today the mining industry is being challenged to improve their production methods. In some markets like nickel, there is pressure to improve productivity and reduce the cash cost per ton. While in other markets like copper and gold, demand is vigorous with favourable pricing, and there are advantages to increase production and productivity given limited plant capacity. Advanced control has proven its capability to improve mineral processing operations through increases in throughput, recovery, as well as reducing variability. In today's mines, autoclaves are being used to a much larger scale and with much larger importance, thus it would be beneficial to improve operational performance through the use of advanced control.Accordingly, it is the author supposition that an opportunity exists in the mining industry to use a proven advanced control technology to improve the operations and financial performance of mines using autoclaves."

Jan 1, 2012

By P. R. G. Brandão, E. E. Ferreira

The presence of metallic cations in solution will affect the aggregation or dispersion of the fine hematite particles, depending on the type of cation adsorption: either specific or non specific adsorption. In this work, the zeta potential measurements were carried out on a sample of pure hematite as a function of pH and metallic cations concentration (Ca2, Mg2+, Mn2+, K+, Na+ and Al3+). The objective of these studies was to clarify the effect of these metallic cations on the surface chemical properties of pure hematite. The cations K+ and Na+ adsorbed as non-specific species and caused only the reduction on the values of zeta potential (in terms of absolute value) over the entire range of pH values tested. For the Al3+ cation, in the acidic pH range it adsorbed as a specific species and increased the zeta potential values. The cations Ca2+, Mg2+ and Mn2+, adsorbed as a non specific species at pH levels less than 6.0 and caused the reduction of zeta potential due to the compression of the electrical double layer. However, for pH values greater than 6.0, these cations adsorbed as a specific species causing the zeta potential to increase and became more positive as the pH value increased (alkaline). This effect could be due to the adsorption of some hidroxy complex species of these cations, which contributed to the positive charge. The effect of metallic cations (Ca2+, Mg2+ and Al3+ concentration, at pH 4.0, 7.0 and 10, showed the following results: a) at pH 4.0, increasing the concentrations of Ca2+ and Mg2+ resulted in on a small reduction in the value of the zeta potential. At this pH, increasing the concentration of A131 cations caused the zeta potential to increase due to specific adsorption of a negatively charged Al3+ hydroxy complex b) at pH 7 and 10, increasing the concentrations of Ca2+ and Mg2+ caused the zeta potential to change its charge from negative to positive.

Jan 1, 2004

By G. Gabra, M. Nagamori, J. J. Panneton

"RESUMELa calcination contrôlée de 10 serpentine permet de produire de 10 magnésie active. Le degré de I'activation est mesure par 10 solubilité du magnésium dans les acides faibles tel que I'acide acétique, La serpentine contenue dans les résidus d'amiante du Québec peut donc être activée par calcination. Le teneur en magnésie active des rejets d'amiante calcinés est fonction de divers paramètres: température, temps de calcination, granulométrie, etc. Les rejets d'amiante de différentes provenances démontrent des comportements thermochimiques différents qui sont étudiés dans Ie présent travail au moyen d'ATD, de TG, de la diffraction des rayons X et de la lixivation par l'acide acétique. On constate qu'un maximum d'environ 80% de la magnésie totale peut être activé dans certains rejets d'amiante du Québec et Ie degré d'activation dépend de la provenance.vIntroductionOn sait depuis longtemps que la serpentine, Mg3Si2O5(OH)4, un silicate hydroxylé de magnésium, devient amorphe lorsqu'elle perd de I'eau d'hydratation entre 600 et 700 °C. La serpentine ainsi calcinée est alors dissociée en magnésie et en silice. Cette magnésie, dite active, est soluble dans un acide faible ou même dans les solutions de sels d'ammonium.Plusieurs precédés chimiques ont été proposés afin d'extraire sous forme de composés magnésiens la magnésie de la serpentine. La plupart de ces procédés comportent une activation par calcination de la serpentine préalablement à une Iixiviation par un acide ou par une solution d'un sel d'ammonium.Malgré la contamination par Ie fer et par d'autres éléments, les compositions chimiques des rejets de différentes mines d 'amiante du Québec, présentées au tableau 1, sont très proches de la serpentine typique. Puisque Ie degré d'activation de la magnésie varie grandement d'une serpentine à I'autre lors de la calcination, la première étape de la recherche sur la transformation chimique des rejets d'amiante du Québec se résume à une étude de leurs comportements thermochimiques."

Jan 1, 1982

By Gwenaële Petit, Ulan Massimkhanov, Gilles Joubert

For its Zuuvch Ovoo uranium deposit in Mongolia, Badrakh Energy (partly owned by Orano Mining) is working on the prefeasibility study for exploitation by ISR (in situ recovery). As part of this project, Orano built a 2-cell (each cell is constituted of one producer well located in the center and surrounded by six injection wells in an hexagonal pattern) and a processing pilot plant that will be used to demonstrate the operability and economic viability of an ISR process. Another main objective of this pilot trial is to demonstrate the ability of Orano’s modeling tools to predict the ore behavior under given leaching conditions. To model uranium production by ISR, Orano uses HYTEC, a reactive transport computational software, which was adapted for its existing operation in Kazakhstan (Katco) to predict uranium recovery and reagent usage based on operating conditions. In order to perform similar simulations for this new deposit, Orano engaged in a comprehensive program including ore sampling, detailed characterization, and metallurgical testwork. The mineralogical conclusions were used to prepare a simplified geochemistry for the ore, in particular carbonate and reactive clay grades, uranium mineralization and penalizing elements such as pyrite. Then, bottle roll leach tests were used to characterize dissolution kinetics for smectite clays. Eventually, column leach test results such as pH, free acid, and uranium recovery were modeled on HYTEC to improve the fit of some of the dissolution kinetic parameters. Parameters fitted using metallurgical test work results will now be used as inputs for predictive model at the pilot scale, in order to anticipate operational results and help with operating decisions for production ramp up.

Jan 1, 2020

By D. Moronkeji, R. Maharidge, D. A. Curry, B. J. Davis, U. Prasad, J. Franquet

"Proper shale characterization is crucial in shale gas drilling, exploration, completion and production. Unlike porous sandstone and carbonate reservoirs, the challenge with shales comes from their micro- to nano-darcy permeability ranges and the anisotropy of their mechanical and hydraulic properties. Most porosity-dependent logs are not sensitive enough to capture the true behavior of shales. Consequently, mineralogy and other strength and stiffness-related properties must be determined to characterize magnitudes and variances in shale mechanical and flow properties. In addition, these properties must pass quality assurance/quality control (QA/QC) practices to give confidence in their use in subsequent log calibrations, during geomechanical modeling, or in fracture design models. This paper presents a technique to integrate shale properties that are measured by various methods, and a methodology to perform QA/QC on the data before application.Shale properties originate from various sources, including downhole and laboratory measurements. Physical samples for laboratory testing are usually limited to a few depths. Lab tests are often costly, and replicating in-situ conditions can be difficult or impossible. In addition, results frequently show wide scatter, reflecting inherent depth variability and lateral heterogeneity. Wireline logs provide nearcontinuous data, but rarely yield direct measurements of rock strength properties. Although geomechanical and fracture models use log data, calibrating it with reliable and previously verified lab-measured properties is important. This paper presents a process to perform QA/QC on lab-measured data using various crossplots.Ten mechanical, microstructural and physical properties are graphically displayed to visually characterize shale strength behavior in ambient and in-situ conditions, whether measured or modeled statically or dynamically. These properties are often sourced from different departments. The properties are integrated but are individually subject to the previously mentioned uncertainties. Pairs of property values are crossplotted and compared with correlations from the literature or previously established with qualified data from related formations. Conformance with these correlations gives confidence in the data, whereas outliers are flagged as questionable. Repeating the process with questionable data crossplotted against other parameters for the same depth highlights the property with the greatest uncertainty. The determination of its value is investigated to locate the source of the inconsistency and establish a more reliable value. Where this is not possible, the user has a rational basis for rejecting that property value."

Jan 1, 2015

By A. A. Holland

Introduction The world's largest known deposits of natural sodium sulphate (Glauber salt), generally termed 'alkali ' throughout western Canada, are located in the Province of Saskatchewan: reserves are estimated to exceed 200,000,000 tons. These are surface deposits resulting from the recent or present-day natural evaporation of brines, in which respect they are similar to those occurring in certain other parts of the world, as in semi-arid sections of the United States, Russia, Germany and Austria. In some areas, underground deposits formed hundreds of thousands of years ago have been _encountered in drilling, and indications are that they also were formed under arid or semi-arid conditions. The master key to the formation of deposits of natural sodium sulphate, wherever they occur, is a climate, either past or present, under which evaporation exceeds precipitation over a considerable period of time. Commercial development of the Saskatchewan deposits began about thirty years ago. Previously, the demand for sodium sulphate had largely been met by salt cake produced as a by-product in the manufacture of hydrochloric acid from common salt. The rapid increase in the production of Kraft paper and, more recently, the development of synthetic detergent materials, have caused a marked increase in the market for sodium sulphate. This chemical gives the extra toughness to Kraft paper and is used in detergent compositions in proportions as high as 75 per cent. Saskatchewan now has six commercial plants producing natural sodium sulphate. Production from each in the fiscal years 1947 and 1948 is shown in Table I. The newest and latest plant is that of Saskatchewan Minerals, at Chaplin, which 1s designed to produce up to 150,000 tons of salt cake, 98.5 to 99.5 per cent pure, yearly. This is equivalent to about 24 percent of the total United States production of crude commercial salt cake for 1947.

Jan 1, 1949

By L. C. So, S. Faucher, S. Mostaghel, D. Sauter, S. -Y. Oh, S. K. Lee

"Molten material from pyrometallurgical furnaces is tapped at high temperature, carrying a large amount of heat. Traditional handling methods of slow air cooling or water granulation do not allow for the recovery of heat from slag and matte. Furthermore, water granulation adds an inherent safety risk of explosions. Recently, there have been numerous studies into processes attempting to recover waste heat. However, most of them have never been commercialized due to numerous challenges including scalability, cost, low heat recovery efficiencies, and difficulties in heat utilization. Ecomaister-Hatch has recently developed and commercialized a reliable and simple dry atomization system that allows for heat recovery while eliminating the use of water. Comparisons of pilot and commercialized dry atomization and heat recovery technologies will be presented and challenges of these technologies will be highlighted.INTRODUCTION Slag has traditionally been regarded as an undesired waste product from smelting operations with slag management focused on removal and disposal of “waste”. Over 500 million tonnes of slag are produced per year, carrying with it ~220 TWh of energy (Barati, Esfahani, & Utigard, 2011). Depending on the process, the energy content of slag ranges from 10-90% of the total energy input (Barati, 2011, Rodd, 2010). There has therefore been great interest in recovering energy from slag. Slag handling methods can broadly be classified into three categories: (1) dumping and slow cooling, (2) wet granulation and (3) dry granulation. As discussed below, only dry granulation routes are amenable to heat recovery. Slag dumping involves the slow cooling of molten material and crushing of the resulting solid. In this process, slag is dumped on the ground directly from furnaces or transferred to slag pots that are moved by rail or haulers and then dumped on the ground. The molten material is left to cool and solidify until it can be broken and handled by heavy machinery."

Jan 1, 2017

By Graham Holmes, John Starkey

"The Kinross Kubaka Project is a gold mine located in the Russian Far East. The grinding circuit, comprised of a 6.1 m diameter x 2.74 m long SAG mill and a 4.1 m diameter x 5.5 m long secondary ball mill in closed circuit with cyclones, was built using SAG Power Index and Bond Ball Mill Work Index testing to determine the grinding energy requirements. Extremely cold climatic conditions and the need to keep heated space and capital costs to a minimum, dictated a grinding circuit with no in-circuit crusher and no conveyors external to the mill. High energy requirements for both the SAG mill and the ball mill were correctly predicted and have allowed grinding production tonnage forecasts to be met. Design test data and production results are given.INTRODUCTIONIn 1995 Davy International Canada, now Kvaerner Metals E & C, was commissioned as the Engineer and Project Manager for the Omolon Gold Mining Company, to design and construct a gold extraction plant for the Kubaka gold deposit, located in the Russian Far East. This deposit had been studied extensively in Russia during the exploration phase and a Feasibility Study was completed in 1993 by Kilborn who visited the site twice during that year to inspect facilities and to take metallurgical test samples. More samples were taken in 1995 to check ore hardness variability, as part of the final design program by Davy.The client’s objective in designing the Kubaka grinding circuit was to achieve design tonnage at all times, even when milling the hardest ore zones in the deposit. Since the samples taken in 1993 were taken as composite samples, it was necessary to take additional samples in 1995 to determine the extent of the variability. Six samples were sent to Canada for SAG Power Index (SPI) testing. Five of these were combined as a composite open pit sample, while the sixth sample was taken from the site adits as a composite sample to represent undergound ore. These two composite samples were tested to determine the MacPherson Autogenous Work Index for comparison with the SPI values."

Jan 1, 2001

By G. F. Liu, S. Owada

Platinum Group Metals (PGMs), Pt, Pd, Rh, have been widely used as a three-way catalyst to clean discharged gas from automobiles and therefore a considerable amount of the spent catalysts is generated annually. This paper proposes a novel concentration technology of PGMs by utilizing the double-deck structure of PGM bearing alumina-ceria and cordierite phases. The applied technologies are a combination of heating-quenching, selective grinding and screening for separating alumina-ceria phase from cordierite. Temperature change as a function of quenching time and the thermal stresses applied to both phases were simulated and calculated by FEM, and it was clarified the mechanism of micro-cracks generation at the phase boundary and micro-cracks in alumina-ceria phase, which indicated that separation of alumina-ceria phase from cordierite and selective breakage of alumina-ceria phase could be achieved in the subsequent selective grinding with an attritor. This process could concentrate 46 wt% of alumina-ceria phase into fine fractions with 86 % recovery efficiency. The remaining alumina-ceria phase can be further recovered by applying flotation and so on.

Jan 1, 2015

By Hidenori Hatta, Takero Watanabe, Hideo Yoshida

"The effect of the quenching rate on age hardening in an Al-6.0mass%Zn-0.75mass%Mg alloy sheet was investigated. The quenching rates and aging conditions were as follows: water quenching (WQ) or furnace cooling (FC) followed by pre-aging at 20°C,then artificial aging at 120, 160 or 200°Cwere performed. The peak strength of the FC and the WQ are very similarat120°C aging. It is important high strength was obtained even at the extremely slow quenching rate. On the other hand, the strength of the WQ significantly decreased compared to the FCat200°C aging. GP(I) zones were formed during the pre-aging at 20°C even if the cooling rate was very slow like the FC, and were transformed into the GP(II) ones at 70°C or higher and then into the ?’ phase. However, these zones were dissolved by reversion during heating to 200°C. Thus the strength of the WQ decreased. On the other hand, it is considered that an unknown cluster or GP zone with a thermal stability formed during the FC was not dissolved up to 200°C and was transformed into the ?’ phase. Therefore, a higher strength was obtained in the FC for the200°Caging.INTRODUCTIONAl-Zn-Mg alloys are widely available in commercial production because these alloy have lower quench sensitivity and can be produced by air cooling (AC). Heat treatable aluminum alloys are usually produced by water quenching (WQ) to increase their strength because a high cooling rate inhibits the precipitation of the stable phase during cooling and increases supersaturated solute atoms. However, Baba(1967)reported the strength of an Al-6%Zn-1.8%Mg(mass%) alloy without additional elements quenched by very slow cooling (15°C/min) was 96% of that quenched by WQ. Furthermore,the age hardening at room temperature (RT) occurs after annealing at 410°C followed by furnace cooling (FC, 0.5ºC/min or less)in these alloys. Therefore, the process of annealing at 410 to 430°C for 120 min followed by AC, and reheating at 230°C for 240 min, then cooling is recommended in the specifications (Japan Aluminum Association, 2011). Matsuda and Yoshida(1996)also recommended annealing at 300°C for Al-Zn-Mg alloy extruded products to inhibit age hardening at RT by precipitating the solute atoms and decreasing them in the matrix. It has been considered that the higher the content of excess quenched-in vacancy becomes by WQ, the higher aging rate at RT is obtained. Therefore,it is theoretically and commercially important to clarify the reason why the age hardening occurs relatively quickly in almost no excess quenched-in vacancies such as the FC, and why the same strength as the WQ can be obtained in the FC"

Jan 1, 2018

By P. Wanjara, M. Xiao, M. Jahazi, C. Poon

Using a robotic 4kW Nd:YAG-laser system, Inconel 718 (1 mm sheet) was welded with and without filler wire to investigate the effect of processing parameters, including power input and welding speed, on the weld geometry, microstructure and mechanical properties. By means of both nondestructive testing and microscopic examination, the weld quality was studied to determine the nature of the welding defects (porosity, cracking and bead shape) over the processing range of 3-3.5 kW for the power input and 4.5-6 m-min-1 for the welding speed. Application of the design of experiment methodology permitted the examination of the relationship between the process parameters and mechanical properties, from which the optimized laser welding conditions could be determined for joining Inconel 718. In particular, the research results indicate that Nd:YAG-laser welding technology can achieve defects free, mechanically sound welds with narrow fusion and heat effected zones.

Jan 1, 2006

By John R. Goode

"This paper reviews options for the separation of a mixture of rare earth elements (REE) into its component elements. Earlier separations used selective chemistry such as double salt precipitation and reductive/oxidative processes – methods that still have a place in the industry. Fractional crystallization was developed for more complete separations of adjacent REE. The latter method was replaced by ion exchange (IX), which was in turn replaced by solvent extraction (SX). Two main SX chemistries are in use, solvation and cation exchangers, with several variants (mixed solvents, ionic liquids, etc.) now under investigation. SX plant configurations have evolved including advanced techniques like “hyperlinking”, novel saponification methods, and alternative stripping techniques. The classic mixer-settler is the most commonly employed device although centrifugal contactors have been pilot-tested. Non-dispersive SX options including microfluidic devices and membrane-assisted SX techniques are being developed and could revolutionize the SX option. Other REE separation techniques now being studied include Molecular Recognition Technology (MRT), Free Flow Electrophoresis (FFE), newer IX systems, and electrolytic processes. Additionally, the classical crystallization and selective precipitation methods and newer bacteria-mediated processes, chloride volatilization, high performance liquid chromatography, and magnetic separation systems have been studied. This paper reviews the options and concludes that conventional SX is the technology of choice but viable alternatives could be demonstrated and acceptable within a couple of years.INTRODUCTIONThe chemical properties of the individual REE are very similar which is why REE minerals and ore deposits almost invariably contain a mixture of all fifteen REE, i.e., La to Lu plus Y. That said, the distribution of REE in a given deposit is frequently dominated by the light REE (LREE, i.e., La to Nd). Examples include the Bayan Obo, Mianning, Lynas Mt. Weld, and Molycorp Mountain Pass deposits where heavy REE (HREE – Sm to Lu and Y) typically account for well under 5% of the REE content. The LREE operations produce some HREE but the main sources of these important elements are the ionic clay deposits of Southern China. Importantly, all of the REE recovery operations referenced above, except for cerianite-bearing ionic clay deposits, initially produce a mixed REE precipitate or calcine with a REE distribution similar to that in the ore (Goode, 2016). However, the consumers of the REE, the manufacturers of magnets, phosphors, catalysts, optical glass, etc., require separated products with purities generally ranging from 99% to as high as 99.9999% depending on the element in question and the end use. Hence there is a need to separate the individual REE one from the other. This paper is intended to review the options."

Jan 1, 2016

By P. Molera

"In Catalonia, between the 10th century and 1878, some installations were developed which at first were called ""factories"" and later ""fargas"", since they manufactured iron and steel of low carbon content. Because of its excellent quality, the fame of this metal spread from Catalonia to many countries. Fargas were started in Corsica, the Low Countries, Germany, Oriental India, Madagascar, Finland and along the rivers Orinoco and Mississippi among others. The extractive process used in these fargas has passed into history as the ""Catalan Farga Process"", ""Catalan Process"", or just ""Farga Catalana"". With this technology, raw material was obtained for the fabrication of tools, nails, weapons, grilles, etc. to supply the national and export markets. Aside from meteorites and native iron, found as metallic nodules in basalts in Greenland and Palestine, the ancient civilizations, which had no means to reach the fusion temperature of iron (1535°C), obtained iron by a direct process. Similar processes were used until quite recently (1930s) by certain tribes in Central Africa; holes in the ground were filled with iron ore and coal, and combustion encouraged by blowing air by mouth or with bellows made of animal skins. Thus without melting the iron it is possible to reduce the mineral and obtain a porous and impure metallic mass, which is purified on forging by mechanical squeezing. With a process very likely similar, the famous column at Dehli weighing 6.4 m.t. was built about 300 B.C."

Jan 1, 1999

By K. Iturralde

The article discusses the possibility of automation in refurbishment processes of social dwelling built from 1950 to 1970. These massively produced buildings were mostly designed prior to the law enforcement regarding thermal insulation or accessibility. Nowadays, many of these buildings are being retrofitted. The article focuses on the works in the external envelope. The task of renewing the whole social building stock is big and it requires a systematic process that facilitates a rapid upgrading, without neglecting the specific situation of each case. How could an automatic refurbishment process of these buildings be defined? The process should start with the data collection of the building and the creation of a 3D model using software such as BIM. The project, drafted in 3D, should facilitate the manufacture of building elements by robotics. In turn, it should be noted that during the assembly at the site, the pieces must be fixed quickly and efficiently. Is it possible to implement an automated process for the refurbishment of apartments built in the second half of the twentieth century? To approach the answer, a virtual refurbishment project is performed. The article focuses on the rehabilitation of the building envelope. Furthermore, it gives special attention to the double skin facade. It is well known that a second skin in this type of building can be an element that integrates several functions. Finally, needless to say that refurbishment of residential buildings is a need in our society. By extending its life cycle, robotic refurbishment provides more favorable socioeconomic and environmental capabilities than the sole construction of new buildings.

Aug 1, 2013

By Garston H. Blackwell

For ageing open pit mining operations where the economic viability of another pushback is questionable, mine life can be extended by increasing the wall slope. If the steepening is started where ore intersects the pit wall, the capital outlay for waste stripping is minimal. Such a venture must be conducted safely, and a basic requirement would include loading equipment capable of working remotely. In the application described, alternatives in the choice of loader included equipment available on site, or the purchase and assembly of used equipment. Only electric cable shovels were in use at the operation, and it was thought that these would be more capable of digging high muck piles at the productivity demanded by an increasingly efficient mill, and in a challenging environment less suited to a rubber tired loader or hydraulic front shovel. A decision was made to convert an older electric cable shovel to remote controlled operation and to include the application of semi-robotic control. The conversion was completed successfully and is described, along with methods developed for remote operation of a shovel, and the application of various sensors for semi-robotic operation. A plan of operations to mine out several completed double benches and make two quadruple benches with wide catchment berms is depicted. On completion of this task, the working benches developed would be wide enough to operate at near full production. Prior to moving the remote controlled shovel back into the pit, a large wall instability became active, eventually closing the operation. The instability could have been safely mined using the remote controlled shovel.

Aug 1, 2013

By Owen Matthews

Introduction For the past year and a half, the mill of Cochenour Willans Gold Mines, Limited, McKenzie Island, Ontario has been roasting arsenopyrite-gold concentrates, prior to cyanidation, by means of a roaster employing techniques that are new and novel. The roaster is known as the Dorrco 'fluo-solids reactor', and the technique as 'fluidization'. The reactor has demonstrated its ability to roast a flotation concentrate containing arsenopyrite, pyrite, stibnite, small quantities of other sulphides, and some lime silicates and carbonates, yielding a calcine consisting mainly of porous iron oxide, plus the gold values. This calcine is readily amenable to cyanidation. Bulk shipments of concentrates to a distant custom smelter, as practised prior to this installation, has thus been eliminated, with appreciable savings in smelting charges, freight costs, and interest losses during shipment and smelting. This is the pioneer installation of fluo-solids roasting at a Canadian mill and up to the present performance results have not been published. It is the purpose of this paper to present the information now available for the benefit of other millmen who may be confronted with identical or similar problems to those encountered and solved at Cochenour Willans.

Jan 1, 1949

By W. G. Mine

In September, 1953, seismographs were installed in the Crowsnest Pass area of Alberta and British Columbia to study the 'bumps' which were occurring in the coal mines at Fernie and Coleman, and to investigate the possibility that they might be related to minor earthquakes in the area. During the initial phase of the work, three seismographs were operated at widely separated stations, two in the region of coal mines at Coal Creek and Coleman and one at Turner Valley, distant from any mining operations. Some earthquakes were recorded at all three stations and, in addition, many small disturbances were recorded by the seismographs located near the mines, especially -by the instrument at Goal Greek. A closer network of radio-linked seismographs was then in-stalled near Fernie, the records of which definitely established that the small disturbances were occurring in the mine workings, both active and inactive. No relationship was established between bumps and local earth-quakes in the area. This work was initiated as a -co-operative effort with the Fuels Di-vision of the Mines Branch, Department of Mines and Technical Surveys, which has undertaken a study into the phenomena of ground stress relief in underground mine workings.

Jan 1, 1958

By A. A. Brant

ONE of the reasons advanced for the decline in prospecting and discovery is that, as regards surficial examination, the law of diminishing returns is becoming applicable. Fewer surficially unprospected fields remain; therefore, fewer discoveries by such means result. Much in the nature of mineral resources remains to be unearthed, but even now, and more so in the future, will discovery depend on painstaking petrographic and structural mapping, aided, where necessary, by judicious applications of all the complementary scientific knowledge and devices (e.g., thin section microscopy, geophysics, and drilling) that experience proves effective in localizing a mineral deposit even beneath drift, lake, or muskeg. It is to be expected, then, that the rate of discovery will decrease, that the cost per discovery will greatly increase, and that the work of discovery will become more and more the careful, methodical assembling of field data, conscientiously interpreted on the basis of scientific knowledge by trained, experienced operatives. In view of these trends, the status of applied geophysics to Canadian mining exploration and development work might well be reviewed. The niche which geophysics may occupy relative to geological surveying and drilling has been clarified by the last twenty years' experience. The cloud of somewhat justifiable scepticism that followed the 'geophysical promotion' period of the late 1920's has lifted. Mining, exploration, and finance companies, in open-minded fashion, are seeking sound advice as to what are the scope and limitations of the geophysical methods at present practised. The purpose of this paper and the following one is, therefore, as far as lies within the author's power, to review briefly the geophysical methods at present in practice in Canada, and, at greater length, to joint out impartially and critically their scope, merits, shortcomings, an possible future development. The treatment will be non-technical, the hope being that an accurate statement of the present status of geophysics in Canada may do much to result in a sounder, saner growth of what, in the future, shall undoubted} y prove an increasingly useful tool in exploration and development work. ?

Jan 1, 1942

By N. S. Spence

INTRODUCTION WHILE TITANIUM, the element, has been known for over 150 years, titanium, the metal, is a relative newcomer to the metallurgical and industrial scene. The reasons for this chiefly lie in the refract1Hy nature of titanium compounds; the high melting point of the metal; the great activity of elemental titanium, particularly at temperatures close to .and above the melting point; and the pronounced deleterious influence of certain impurities on its mechanical proper-ties. Early efforts at production of the metal were, consequently, either unsuccessful or resulted in products having sub-metallic properties. With the considerable improvement in equipment, materials, and skills that have developed within the past twenty-five years, later investigators have had a better opportunity to overcome some of the inherent practical obstacles and to come to grips with the essential technical problems. NATURAL ABUNDANCE OF TITANIUM Titanium is one of the most abundant metallic elements. It has been estimated (1) that titanium comp-rises about 0.65 per cent of the earth's crust, and therefore ranks fourth among the structurally useful metals in the order: aluminum, iron, magnesium, titanium. It must be appreciated that the relative abundance of the element is only a crude indication of its potential availability, since a very substantial proportion is present as a minor constituent in practically all igneous rocks. By comparison, present-day ores of titanium are relatively few and are but a minor fraction of the estimated total titanium contained in the earth' s crust.

Jan 1, 1951

By I. Haskett

ABSTRACT The Redwater pool, in north-central Alberta, was discovered in October, 1948, and at the end of 1950 was about 85 per cent developed. Production is from a Devonian coral limestone reef and is found at an average depth of 3,150 feet. The pool has an estimated .productive area of 37,000 acres, and a maximum oil zone thickness of slightly over 200 feet. Wide variations exist in both type and values of porosity, with the average value determined for the reservoir being 6.16 per cent. The total stock tank oil in place is about 1.24 billion barrels. The crude has a saturation pressure of 485 psig, com-pared to the original value of 1,050 psig for the reservoir, and the principal recovery mechanism so far has been the natural water drive. Cumulative production to January 1st, 1951, has been about 15.5 million barrels. These withdrawals resulted in a reservoir pressure decline of slightly over 100 psi. Predictions of future behaviour indicate that the water drive will not be of sufficient magnitude to maintain the reservoir above saturation pressure past 1953, and that, with natural depletion, the pool will be produced largely by a solution gas drive. Pressure maintenance by water injection has been considered and the possibility of raising the pressure to the original value of 1,050 psig is also discussed. INTRODUCTION WITH the discovery of the Lewduc pool, early in 1947, the Devonian limestone became the major geological formation contributing to Western Canada's rapidly growing petroleum reserves. Redwater, discovered in October, 1948, is now the largest known Devonian pool in Canada, with a recoverable reserve estimated at approximately 500 million barrels. Until recent years, the knowledge of the nature and characteristics of this type of limestone reservoir has been comparatively limited.

Jan 1, 1951