Search Documents

By H. C. L. Reemeyer

One of the fundamental trade-offs for copper concentrators is between grinding circuit product size and copper recovery. The capital and operating cost savings and throughput increases for a coarser grind should be evaluated against potential recovery reductions. Other benefits of coarser grinds, such as GHG emissions reductions and favourable effects on tailings and water management should also be considered. This paper assesses the formation of laboratory and pilot test programs, design of process flowsheets, equipment selection, and evaluation methods to determine the most appropriate and economical grind size for a given deposit. The paper will include an evaluation of case studies. INTRODUCTION The majority of the world’s mined copper comes from sulphide deposits, which are mostly processed using crushing, grinding, flotation and dewatering flowsheets to produce copper-bearing concentrates for smelting. Ores must be ground to a sufficiently fine size to achieve an acceptable level of liberation to allow both high recovery of copper and valuable by-product minerals while efficiently rejecting gangue to tailings. Therefore, a key design parameter in process plant design is the grind size of the flotation feed. Copper concentrators use a variety of grind size targets that depend on various factors, including ore mineralogy and the grain sizes of valuable and gangue minerals; the sensitivity of valuable mineral recoveries in the rougher flotation stages to grind size, ore hardness; electricity costs; and mining vs. processing throughput constraints. Typically, copper and by-product recovery increase as grind size is reduced, which can improve revenue, but finer grinds increase power and grinding media operating costs and may have implications for tailings management. This paper explores the trade-offs that should be assessed in determining the optimum grind size, and to answer the question if coarser grinds are worthwhile. METALLURGICAL AND FLOWSHEET FACTORS Recovery-by-size behaviour of sulphide-bearing particles In base metals sulphide flotation, it is typical that flotation recoveries vary by particle size. Metal sulphide particles rendered hydrophobic by collector in intermediate size ranges (e.g. 10 to 100 um) usually show very high recoveries, often approaching 100%. Recovery usually falls away in finer size fractions (<10 um) as fine particles have little inertia and can move around bubbles without colliding and attaching to them. Coarser particles (>100 um) are susceptible to particle-bubble detachment and dropback (Jameson, 2019).

Jan 1, 2019

By J. G. Manchuk, M. Thurston

"The degree of uncertainty associated with a natural diamond resource is important to quantify from the time of discovery through the production lifetime. Data collection occurs during the discovery, exploration, delineation, and production or recovery phases. Quantifying the relationship between data and uncertainty is an important component of project valuation. The value of data is measured as their potential to reduce uncertainty if they are collected. A method is developed using Monte Carlo simulation for predicting resource uncertainty and valuing data during critical phases of development, particularly discovery and exploration. The technique is applied to diamond pipe deposits.RÉSUMÉ Il est important de quantifier le degré d’incertitude associé à une ressource diamantifère naturelle, depuis le moment de sa découverte et durant toute la durée de l’exploitation. La collecte de données se fait durant les phases de découverte, d’exploration, de délimitation, et de production ou de récupération. La quantification de la relation entre les données et l’incertitude est une composante importante de l’évaluation du projet. La valeur des données est mesurée en tant que leur potentiel à réduire l’incertitude si elles sont recueillies. Une méthode a été développée qui utilise la simulation de Monte Carlo pour prédire l’incertitude de la ressource et évaluer les données durant les phases critiques du développement, surtout celles de la découverte et de l’exploration. La technique est appliquée à des gisements de cheminées diamantifères."

Jan 1, 2015

By Ralph V. Stewart

"The asbestos orebody is contained within ultrabasic rocks of Precambrian age, being located in the continuous permafrost zone of the Quebec Ungava Peninsula, some 300 miles north of the tree line at approximate latitude 61'49' and longitude 73°58'.The asbestos deposit is at the western tip of a folded ultrabasic sill complex which trends northeast and covers an elliptical area 4.5 miles wide by 15 miles long. Locally. the asbestos occurs in. a completely serpentinized dunite rock. The principal rock types in the vicinity of the ore-body originally consisted of dunite, peridotite and pyroxenite, all of which have experienced at least two periods of alteration, so that no fresh rock now remains.The main ore zone in the open pit is approximately one quarter mile in length, 150 to 200 feet in width, and plunges at 25 to 30 degrees in a northeast direction below surface, to a vertical depth of at least 1,200 feet, Consider¬able tectonic activity resulted in favourable structural conditions which culminated in the formation of the ore zone in its present form.The deposit consists principally of cross-fibre ""gash type"" veins which vary in length from several inches to several feet. The principal fibre vein direction is parallel to the dip of the enclosing serpentinized dunite and sill complex.Some of the problems encountered during diamond drill¬ing in permafrost are briefly discussed."

Jan 1, 1976

By Frank Martonhegyi

"The objective of this paper is to review the coal basins in the Canadian part of the Western Cordillera to aid their understanding, and to aid in finding and proving places of economic coal mining potential. Coal occurs in eugeosynclinal basins in the Western Cordillera which evolved through three stages: -from systems of volcanic arcs in the Late Jurassic to mid-Cretaceous; -through an intermediate stage with deposition in increasingly restricted successor basins in Jurassic to Early Tertiary; -to a continental stage by the Eocene. Minor coal seams occur usually in late volcanic arc stage sediments bur they can be locally thick as they are on Queen Charlotte Islands. Successor basins usually show a marine-paralic-limnic evolurion. Signijicanr coal deposits occur in the tarter two sequences in the Whirehorse (Tantalus) and Bowser (SkeenaSusrur) basins. Currenr activities are intensive in the more accessible Bowser Basin, for example at Telkwa, Susrut River and on the Groundhog coal field. On Vancouver Island major coal seams occur in cyclic sediments, but the more accessible deposits are mined our. Exploration renewed recently in the less accessible northern part of the Island, for example Quinsam, for surface mineable coal. The Western Cordillera is a mosaic of allochtonous tectonic blocks. They originated from the south and were displaced northward by several hundred kilometres. Many Tertiary coal basins are related to strikeslip transcurrent faults along which the later part of displacement took place, for example the Dawson coal area in the Tintina Trench. Tensional and dipslip normal faulting also created or enhanced sites for thick peat accumulation. For example at Hat Creek 280 m of coal occur in a 550 m section. Secondary structures are often better exploration targets than the main fault zones. Pluvial and alluvial fan environments away from the main drainage are usually the favourable sites for thicker and cleaner coal deposition."

Jan 1, 1985

By David M. Knowles, R. Gordon Gastil

"The Precambrian sedimentary series of the Labrador geosyncline, including iron formation, extends into southwestern Labrador and adjacent Quebec. The iron formation consisted of primary oxide, silicate, and carbonate facies which were deposited simultaneously in an irregular basin in response to migratory environmental conditions. The iron formation isochemically recrystallized to coarse-grained quartz-iron oxide, iron silicate, and quartz-iron carbon-ate rocks during prolonged regional metamorphism. The rocks are deformed on two deformation axes intersecting at large angles, and are characterized by isoclinal to recumbent folds. Parts of the formation have been profoundly affected by a post-metamorphic leaching and oxidizing environment."

Jan 1, 1959

By R. C. Wallace

In the early explorations of the Northwest, the search for minerals played a not inconsiderable part. The first episode had its disillusioning sequel. Sir Martin Frobisher, in 1576, sailed up that bay in Baffin land now known as Frobisher bay, thinking that he had the coast of Asia on his right hand. He brought back from this expedition a piece of &apos;black earth&apos; from Hall island, from which an alchemist by coaxing nature, or his own conscience, obtained gold. A second expedition of three ships was fitted out in 1577, and a third of fifteen ships in 1578. The ships were loaded with this &apos;black earth&apos;, which on subsequent investigation was found to be worthless, and interest in minerals for the time being ceased. In 1612 Hall and Baffin went in search of a gold mine near the Arctic circle on the west coast of Greenland, reported to be worked by the Danes. They found old workings, but no ore. To come nearer the Hudson Bay area, it is noteworthy that the charter granted by Charles II to the Hudson Bay Company in 1670, as a result of the explorations of Radisson and Groseillers, was given "-in consideration for their having at their own cost and charges undertaken an expedition to Hudson bay in the northeast parts of America, for the discovery of a new passage to the South sea, and for the finding of some trade for furs, minerals and other considerable commodities, and of their already having made by their undertakings such discoveries as did encourage them to proceed farther in pursuance of the said design, by means whereof there might probably arise great advantage to the King and his Kingdom - ".

Jan 1, 1925

By A. F. Gregory

"AbstractA resumé of aerial radiation survey studies performed by and for Eldorado Mining and Refining, Limited, since 1943 is presented. Flight tests were initiated in 1947 and were followed .by intensified use and study of Geiger counters and other radiation detectors. Development of an aerial scintillation counter began in 1948, but •a sensitive large crystal unit was not available for exploration purposes until 1950. Modifications of this unit have been used in all subsequent surveys.For the Eldorado detector, several limiting conditions were established for successful radioactivity detection, the most important being that natural vein exposures can only be assuredly detected .at distances less than 150 feet. Sedimentary and pegmatitic radioactive occurrences can be detected at much greater distances. A helicopter investigation technique appears to •have •a useful prospecting potential.IntroductionAerial radiation surveys were first proposed in the early 1940's. However, it was not until 1949 that airborne detectors were extensively used in the search for radioactive minerals. Eldorado has flown about 50,000 miles of exploration flights, exclusive of tests, using a variety of •detectors and aircraft. Considerable data have •been gathered for .the evaluation of the several techniques employed. Much of the early work was performed with the co-operation of the National Research Council of Canada ( 1). More recent work was done in conjunction with the Commercial Products Division of Atomic Energy of Canada, Limited. The Development Department of this latter corporation designed and built the scintillation counter used in recent Eldorado surveys."

Jan 1, 1955

By SANDVIK WHITE

The mining industry produces approximately 4-7% of global greenhouse gas (GHG) emissions. It is fundamental for mining operations to take immediate sustainable action to actively contribute to an emissions-free future for the next generations. The mining industry has traditionally relied heavily on diesel technology and transitioning to more sustainable solutions requires change management to drive cultural acceptance and new product development. Sandvik was interested to find out the lifetime emissions of a single drill rig and to compare similar application diesel and BEV drill rigs with same use profile to each other. That led the calculation and pondering towards comparing different countries and mine sites as well

Jan 1, 2023

ABSTRACT Understanding process histories and worker exposures in nickel production operations is critical in determining the role nickel compounds play in respiratory cancer incidence. As part of a series on Vale Canada’s (previously known as Inco) nickel processing operations, this paper includes descriptions of Ni electrolytic operations at refineries in Port Colborne, Ontario (1922–1984), and Thompson, Manitoba (1961–present). Industrial hygiene measurements, by area and personal sampling, of workplace aerosols at these operations are reported.

Jan 1, 2014

By Tyson Birketi, Françoi Robert, Steve Green, Dan Richardson

Detailed sampling using a portable diamond drill, and inter laboratory comparison of selected samples have been combined with statistical studies of truncated populations to establish the gold content of several outcrops in the Val d&apos;Or area. The outcrops chosen are non-mineralized. The background gold concentration in the rocks of the region is 5 ppb or less. Gold is distributed relatively homogeneously within the outcrops studied except for slightly increased concentrations within quartz-tourmaline veinlets. Three samples, of which 20 grams of powder are analyzed for each, can adequately determine the gold concentration of a structurally simple outcrop in the Val d&apos;Or area.

Jan 1, 1992

By R. B. STEWART

A few days ago, while reading a report of the late Dr. Robert Bell in preparation for this afternoon&apos;s meeting, I found some impressive figures concerning the magnitude of the Hudson Bay basin. From the waters of the Bay itself, this great territory extends eastward 500 miles, westward l,300 miles to the Rocky mountains, and southward to the source of the Red river. It has a width of 2,100 miles from east to west, and a length of l,500 miles from north to south. Its area is almost three million square miles. It is not, of course, my intention to review the natural resources of this vast territory, but to confine my remarks to that portion of it adjacent to the waters of Hudson bay. A number of erroneous ideas exist in the minds of many concerning this northern country, especially as regards its latitude and climate. Burwell, at the entrance of Hudson strait, is in the latitude of 60 degrees or roughly that of the north of Scotland. The southern end of James bay has about the same latitude as the northern end of Vancouver .island.

Jan 1, 1928

By L. A. Anestiev

A method based on use of calorimetric data for the determination of solidification kinetic parameters is proposed. The method incorporates recent theories of nucleation and growth and allows modeling heat fluxes observed in calorimetric experiment. Statistically optimal estimations of the kinetic parameters, which include the activation&apos;s energies of nucleation and growth, are derived from experimental data by means of nonlinear regression analysis. The method is applicable to pure substances and alloys. The evaluation of the kinetic parameters characterizing solidification of pure Al is used for clarifying and exemplifying the method.

Jan 1, 2004

By G. F. Carr

"IntroductionFLUORSPAR has been found at several •localities in Newfoundland, but all the commercial deposits discovered to date are in the vicinity of St. Lawrence, a town on the southeast coast. Most of the veins are within six miles of St. Lawrence harbour, and between sea-level and an altitude of 400 feet. The St. Lawrence Corporation of Newfoundland, Limited, and Newfoundland Fluorspar, Limited, a subsidiary of the Aluminum Company of Canada. Limited. are the two producers.With the arrival of 1953, the St. Lawrence area entered upon its twenty-second •consecutive year as a producer of fluorspar. Production has increased more or less steadily during this period, as is shown by the fact that approximately one-half of the total shipments to date have been made during the past six years. Between four and five hundred men are employed by the industry, and more than $1,250,000 was paid out in wages and salaries during 1952. Shipments during that year reached an all-time high of 81,283 tons valued at $2,484,943, compared with 67,925 tons valued at $1,966,477 in 1951 (1).As a result of an agreement made in July, 1952, with the United States Defence Materials Procurement Agency, production of the St. Lawrence Corporation, Limited, and St. Lawrence Fluorspar, Incorporated, an affiliated company, will •be increased by .approximately 50,000 tons of acid-grade fluorspar per year. The contract extends over a period of four years, or until 150,000 tons of acid-grade concentrates have been produced."

Jan 1, 1954

By A. Tylczak, C. Shook, A. Doogan-Smith, S. Loif, B. Hilscher, P. Nayak

"This paper discusses how to effectively conduct energy efficiency studies during the design of new mineral processing plants and plant expansions. Energy management studies for new plants are ideally conducted as part of the feasibility study, but can also be done at the detailed design stage prior to the purchasing of equipment. Energy management engineers work as part of the mineral processing plant design team.Such studies usually result in energy savings of approximately 3-8% of the predicted plant’s energy consumption and energy demand. Potential cost savings can be significant. A variety of mineral processing systems – crushing/grinding, pumping, materials handling, fans/blowers, compressed air, and others – are assessed within this study.Energy Management Information System (EMIS) studies can also be performed for the new plant or plant expansion, as an independent study. EMIS can be incorporated into the electrical and controls design of the plant.Most Canadian Utility companies fund new plant design studies and provide financial incentives based on the predicted energy savings and incremental cost of the more energy-efficient design. A new plant energy efficiency study improves the potential for energy reduction because only the incremental equipment cost is included in the project return-on-investment calculation. After the design and construction phases, energy efficiency projects must justify the entire cost of the upgrade, which is significantly higher than the incremental cost alone.This paper outlines the major steps of a new plant/plant expansion energy efficiency study, the available utility company incentives, and the areas yielding the largest potential energy savings.IntroductionThis paper discusses energy efficiency studies and energy management systems with regards to mining operations. Energy management refers to the systems of monitoring, analyzing, and optimizing energy usage within a facility. It includes energy efficiency optimization of the initial plant design as well as the implementation of an Energy Management System (EnMS) and Energy Management Information System (EMIS) for optimizing energy usage over the lifetime of the facility. An EnMS is the organizational framework and procedures for managing energy use; an EMIS is the system of monitoring, reporting, and tracking process energy use against targets."

Jan 1, 2016

By A. Rodriguez-Prado, P. Kuschk, R. L. Legge, W. C. Lennox

Using constructed wetlands to chemically reduce hexavalent chromium Cr(VI) to Cr(III) from industrial and mining wastewater has proven to be feasible and efficient. Applying first-order kinetics to describe the process is simple, but in some cases a more accurate model is required to reflect the process. This paper studies the feasibility of using non–first-order kinetics to describe the reduction process. Results indicate that half- and second-order kinetics adequately described Cr(VI) reduction in laboratory wetland mesocosms. The organic carbon content played a relevant role, whether it was built up by plant growth or spiked into the feed water.

Jan 1, 2014

By Luc Harnois, Gabriel Voicu, Marc Bardoux, Robert Crépeau

"Abstract-Detailed petrographical and geochemical studies have been carried out on the igneous and sedimentary rocks in the Omai area, part of the Paleoproterozoic Barama-Mazaruni greenstone belt, Guyana. The stratigraphic succession at Omai begins with basalts, associated with mafic-ultramafic intrusives and poorly-sorted conglomerates; these are overlain by andesites and quartzfeldspar porphyries, with pelites and tuffaceous sediments at the top. The volcanic-sedimentary succession was intruded by a quartz-monzodioritic stock (Omai stock) and granophyric rhyolite dikes. Several generations of mafic dikes were intruded discontinuously from the Mesoproterozoic to the Permo-Triassic. Volcanic rocks range in composition from subalkaline basalt to high-silica rhyolites, with a gap between 60% to 70% SiO2, which suggests the suite is bimodal. Major, trace, and rare earth element criteria were used to subdivide the rocks into tholeiitic and calc-alkaline types. The tholeiitic rocks are characterized by flat to moderately sloping chondrite-normalized REE patterns. On the basis of immobile trace-element ratios, the tholeiitic mafic rocks from Omai have characteristics of immature intra-oceanic island arcs, or of E-MORB basalts affected by a strong arc signature, as is commonly reported for back-arc basin basalts. The andesites, quartz-feldspar porphyries, rhyolites and quartz monzodioritic stock are calc-alkaline, with strongly sloping REE patterns, enrichments in the large-ion lithophile elements, and depletions in the heavy REE and high-field-strength elements, features which are typical of more mature island-arc settings.At Omai, two types of gold-bearing veins can be distinguished: vein sets (± stockworks) and tension veins, both post-dating the regional metamorphic peak at the level they were emplaced. The relationship between the gold mineralization and its host lithologies does not seem to be genetic. Rather, the emplacement of mineralization was strongly influenced by the rheological contrasts between the intrusive/subvolcanic bodies and the volcanic/sedimentary country rocks. These contrasts helped to focus the regional stress upon the more competent intrusive subvolcanic bodies, resulting in brittle fracturing, and therefore in greatly enhanced permeability to hydrothermal fluids. The Omai gold mineralization can be classified as late tectonic, with its emplacement controlled by the last brittle to brittle-ductile stages of the Trans-Amazonian orogeny."

Jan 1, 1997

By Gabriel Voicu, Harnois Luc, Marc Bardoux, Robert Crépeau

"Detailed petrographical and geochemical studies have been carried out on the igneous and sedimentary rocks in the Omai area, part of the Paleoproterozoic Barama-Mazaruni greenstonebelt, Guyana. The stratigraphic succession at Omai begins with basalts, associated with ma?c-ultrama?c intrusives and poorly-sorted conglomerates; these are overlain by andesites and quartz-feldspar porphyries, with pelites and tuffaceous sediments at the top. The volcanic-sedimentary succession was intruded by a quartz-monzodioritic stock (Omai stock) and granophyric rhyolitedikes. Several generations of ma?c dikes were intruded discontinuously from the Mesoproterozoicto the Permo-Triassic. Volcanic rocks range in composition from subalkaline basalt to high-silicarhyolites, with a gap between 60% to 70% SiO2, which suggests the suite is bimodal. Major, trace, and rare earth element criteria were used to subdivide the rocks into tholeiitic and calc-alkaline types. The tholeiitic rocks are characterized by ?at to moderately sloping chondrite-normalized REE patterns. On the basis of immobile trace-element ratios, the tholeiitic ma?c rocks from Omai have characteristics of immature intra-oceanic island arcs, or of E-MORB basalts affected by a strong arcsignature, as is commonly reported for back-arc basin basalts. The andesites, quartz-feldspar porphyries, rhyolites and quartz monzodioritic stock are calc-alkaline, with strongly sloping REE pat-terns, enrichments in the large-ion lithophile elements, and depletions in the heavy REE and high-?eld-strength elements, features which are typical of more mature island-arc settings.At Omai, two types of gold-bearing veins can be distinguished: vein sets (± stockworks) and tension veins, both post-dating the regional metamorphic peak at the level they were emplaced. The relationship between the gold mineralization and its host lithologies does not seem to be genetic. Rather, the emplacement of mineralization was strongly in?uenced by the rheological contrasts between the intrusive/subvolcanic bodies and the volcanic/sedimentary country rocks. These con-trasts helped to focus the regional stress upon the more competent intrusive subvolcanic bodies,resulting in brittle fracturing, and therefore in greatly enhanced permeability to hydrothermal ?uids.The Omai gold mineralization can be classi?ed as late tectonic, with its emplacement controlled by the last brittle to brittle-ductile stages of the Trans-Amazonian orogeny."

Jan 1, 1997

By Eric Schraml

Wardrop Engineering and the Placer Dome?s Campbell Mine Design Team utilized leading edge directional raise boring techniques and an innovative, remote controlled application of steel fibre reinforced shotcrete ground support to achieve improved mine ventilation and a superior, safety focused secondary emergency egress. While more standardized methods may have provided a sufficient solution to either the requirement for a ventilation raise or for a traditional escape ladder way, innovative methodology ensured both objectives were met with a single, enhanced solution. Placer Dome committed to provide a solution that minimized energy consumption, optimized air delivery and facilitated an escape way focused on minimizing the negative physiological aspects associated with mine evacuation. The project was successful in providing a new airway, returning 47 m3/s (100,000 cfm) from the 39 Level to 30 Level, minimizing risk to the raise equipping crew and providing a fully equipped escape hoist. The resulting secure escape environment provided an efficient means of evacuating personnel working at depth without necessitating a potentially dangerous exhausting climb to surface. The project has substantiated, that optimized safety focused design can be achieved without jeopardizing project economics.

May 1, 2002

By G. W. Sparkes

The use of CR-39 plastic polymer as a solid state nuclear track detector in the textural analysis of radioactive minerals in geological samples was first described by I.R Basham in 1981. CR-39 autoradiographs provide a detailed, high-resolution image of the in situ distribution of the radioactive minerals within geological samples on both the macroscopic and microscopic scales. This technique is an inexpensive and effective means of obtaining detailed textural information that provides insight into the style of mineralization, its relationship to primary and secondary structures in the host rock, and its association with particular geological features or mineral phases. Although this technique does not provide any information on the identity of the minerals responsible for the radioactivity, the resultant autoradiographs can be used to select regions for further detailed analysis such as petrography, microprobe analysis, or SEM imaging. This paper summarizes the procedure and outlines the appropriate time and materials required for both the exposure and etching of the CR-39 with respect to the intensity of the radioactivity emitted by the geological samples.

Jan 1, 2013

By H. Brodie Hicks

"THE REVIVAL of the Mayo mining camp, with particular reference to the activities of United Keno Hill Mines, Limited, has been one •of the more spectacular and also one of the most important of the post-war developments in the Canadian mining field. The geological location of the camp, coupled with other natural disadvantages, have in the past limited the mining area to small-scale, highgrading operations, but the post-war improvement in metal prices has now broadened the possibilities and has led to the considerable success achieved by United Keno Hill Mines, Limited, and the present boom-type development by a whole host of newcomers to the field.LocationYukon which has an area of 207,000 square miles, is showing ever increasing possibilities as a mineral source of great value and more and more attention is being focussed on the Territory. The accompanying generalized map (Figure 1) shows the main transportation routes and mining districts.The Mayo Mining District comprises roughly the eastern two thirds of Yukon Territory lying north of McMillan river and south of the Peel. The district was one of the first in the Territory in which placer gold was discovered, but the occurrences proved of minor importance. Other minerals reported include ores of tungsten, tin, antimony, and several other metals, but of primary importance have been the ores containing silver-lead-zinc-cadmium now being developed and mined in the Keno area. Similar ores have been found over a very considerable area, extending some 50 miles north, 15 miles east, 30 miles west, and 10 miles south of the townsite of Keno Hills, Keno City, a total area of 2,700 square miles."

Jan 1, 1952