Search Documents

By J. Girard, V. Aubé, M. Barakate, S. Bellec, M. R. Eddahabi, Y. Chaik, M. Deshaies

"The activated carbon used in the carbon-in-leach (CIL) process to absorb gold is subject to breakage. This carbon breakage can be minimized, but it will always be necessary to deal with fine carbon particles, known as carbon fines. These fines contain a significant amount of gold and mining operations generally struggle with the treatment of this product. Since IAMGOLD’s Essakane mine is located in Burkina Faso, shipping carbon fines out of the country was not considered a viable solution due to the logistical burden and legal procedures in place. A benchmarking study demonstrated the complexity of treating carbon fines on site. IAMGOLD partnered with the host government to find an innovative approach to economically recover the gold locked in these fines. This paper describes the new circuits commissioned in July 2016 built to improve carbon fines collection, incinerate the carbon fines and leach the gold in the ashes produced by incineration. These new circuits successfully demonstrate that it is possible to extract more than 94% of the gold content in the carbon fines. This is profitable for the company as it improves the overall mill recovery rate by 1.0% to 1.5% and significantly decreases gold inventory build-up on site.INTRODUCTION The activated carbon used in the carbon-in-leach (CIL) to absorb gold is subject to breakage. This breakage can occur in the CIL tanks, the stripping circuit, the regeneration process or anywhere throughout the pumping and handling processes of carbon through the circuit. Fine carbon particles are invariably created and, because of their small size, present a large specific surface which favors gold absorption (Hilsher et al., 2014). At the very beginning of operations at Essakane, the carbon fines were recovered by means of a thickener and a filter press, but the circuit was undersized and inefficient. Subsequently, a decantation basin was used to settle the fines before the thickener. The settled fines were shovelled from the basin into bags. All these bags were stored in the backyard of the plant. The average tonnage of carbon fines recovered monthly was 23.5 tons with a gold grade at 1938 g/t."

Jan 1, 2017

By F. W. Guernsey

Of all the elements, sulphur occupies a place by itself. It is mined in situ, in such quantities and of such purity that, as regards the tonnage produced, it is the first of any element on the list. Iron and coal the great tonnage producers, are combinations of elements, while sulphur is mined and marketed almost chemically pure. It is sold, in large quantities, commercially, calling for a purity of 99.5 per cent while for medicinal purposes, the Pharmacopoeia requires only 99 per cent. purity. It is a very common commodity, and like many common things is of extreme importance, in the progress of our civilization. The substance has been known from the earliest times, the word sulphur being derived from the Sanskrit Culvari", hence the Latin Sulphur. Commercially it is also called brimstone, this word being a derivative of the Anglo-Saxon Bryne Stane or burning stone. From our younger days, we have been more or less familiar with the mineral. On the spiritual side being threatened, if we did not behave ourselves, with an ultimate consumption in a lake of fire and brimstone, (which in moments of reflexion was not pleasant to contemplate) while our bodily ills were taken care of by inward applications as a spring medicine. In both instances, the effect required, was generally attained. Sulphur occurs in nature, both free and in the combined state, it being estimated that it forms, over one tenth of one per cent of the first ten miles of the earths surface. (I do not know who did the estimating and it is not guaranteed).

Jan 1, 1923

By M. V. Rowley, D. D. Warkentin

With high commodity prices, tightening operating budgets and increasing disposal costs, there is an increasing interest in processing municipal waste streams, such as the ash derived from combustion processes. This paper describes laboratory development work for a process to recover metal values from the finer fractions of these wastes. The work was initially aimed at recovery of copper and the removal of lead and other heavy metals from the ash residue, but results showed gold and silver recovery to be an important objective as well. The process uses gravity and flotation as the principal separation steps, with gold recovery occurring mainly in the flotation stage. The particle size range and chemistry of the ash presented numerous challenges to developing a suitable flotation method, but an effective flowsheet was developed by separating the ash into a fine fraction and a separate slime fraction, each with a unique flotation strategy. Specialized conditioning stages and careful reagent selection have resulted in effective gold and silver recovery from a range of ash types and sources. The work has resulted in a patent being issued for a process based on this novel approach to the treatment of combustion wastes.

Jan 1, 2017

When selecting a method for monitoring crack growth in pipeline steel, the sensitivity or crack-size resolution plays a dominant role. Even though there are several visual and non-visual methods, the direct current potential drop (DCPD) method is very effective for monitoring crack growth because of its resolution. This method has been used for the past few decades and has gained increasingly wide acceptance in fracture research as one of the most accurate and efficient methods for monitoring the propagation of cracks. Furthermore, most R&D experience has proven that the electrical potential method can be used in most "aggressive" environments. For these reasons, the DCPD method was selected to design a testing machine to monitor corrosion fatigue crack growth. The use of finite-element modelling is shown to facilitate the application of the DCPD method for monitoring crack growth in steels. The 2D model calibration provided a good description of the test data and proved more accurate than the analytic Johnson's formula.

Jan 1, 2005

By M. Mai Manga, M. Renaud, A. Faucher, C. Bazin

ABSTRACT Grinding circuits are operated in the presence of disturbances resulting from ore changes and equipment malfunctions, such as hydrocyclone overloading, worn or partly plugged apexes, surging, and internal liner detachment that may cause a loss of classification performance. Metal recovery losses in downstream leaching or flotation circuits justify the development of methods for rapid detection of hydrocyclone malfunction. Two methods are presented in this paper. The first method uses measurements from sensors available in a grinding circuit and the second uses vibration sensors installed on the individual hydrocyclones of a nest.

Jan 1, 2011

By R. C. Hartviksen, B. H. Boyum

"The Sherman Mine, Temagami, Ontario, is an iron ore pellet operation rated at one million tons per year capacity. Mining is done from three open pits in two bands of Keewatin iron-formation intercalated in a 'greenstone belt' thought to be part of the Archean 'Abitibi Belt'. The bands of iron-formation are tabular and steeply dipping, averaging 75 degrees. The principal ore mineral is magnetite.Blast holes, 1214 inches in diameter, are drilled on 28-foot centers, each hole being sampled and assayed for both total iron and magnetic iron. Concentration tests are made in the laboratory to determine the anticipated concentrate grade. Two classes of ore are recognized -'liberating' or 'refractory'. Blending is done on iron con-.tent, degree of ease of liberation (i.e. grain size) and chunkiness. The latter is important, as primary milling is done in autogenous mills. Actual daily mill results are compared with predicted grade from blast holes, exploration diamond drill holes and pit inspection. Hourly mill samples are analyzed by the X-Ray Fluorescent Analyzer, with emphasis on silica grade. In 1969, the pellet grade was improved from 7 .01 per cent silica natural to 5.50 per cent silica natural."

Jan 1, 1970

By M. Sahoo, P. Burke, Y. Fasoyinu, J. P. Thomson

The effects of grain refinement, mold temperature and chemical composition on the hot tearing resistance of aluminum alloys 535.0 and 206.0 has been studied by pouring constrained rod castings in metal molds. In addition, two prototype components that could be used in automotive applications were also poured from both alloys by gravity tilt-pour and low pressure permanent mold casting processes. This paper summarizes the results and issues encountered during the casting trials. It was shown that grain refinement and mold temperature ::::: 400°C reduced, and sometimes eliminated hot tear cracks in both alloys. The two prototype engineering components could be cast successfully from both alloys in metal molds. The metallurgical issues related to molten metal treatment and processing temperatures were well controlled. However, issues related to the control of hot tearing, casting and mold design must be addressed in future studies to guarantee the production of defect free castings.

Jan 1, 2006

By A. Allaire, J. Torrealba-Vargas, R. Welyhorsky

Early testwork was carried out to select the plant process design criteria and flowsheet selection. Additional testwork was carried out during the feasibility study to support the optimization of the plant design criteria. The test results showed that the recovery of gold was not very sensitive to grind size in the range of 75 to 105 microns. An additional result was that the presence of lead nitrate did not improve the kinetics of gold leaching. This conclusion was supported by the low content of sulphides in the ore. It was also found that the presence of lead nitrate increased copper dissolution, producing the potential for an increase of copper reporting to electrowinning, which is detrimental to the overall gold recovery process. The use of oxygen in leaching was investigated to increase leach kinetics. The results of leaching tests to compare using oxygen instead of air indicated that, due to the improved leach time, it was possible to reduce the number of leaching tanks from twenty four (24) to twenty (20).

Jan 1, 2011

By E. V. Konopleva, H. J. McQueen

Steels in high variety have been providing strength and ductility for more than a century mainly through complex heat treatments following hot shaping. The economical and sustainable goal was a steel with the two operations combined through applying knowledge of dislocations and strengthening mechanisms aided by new mechanical and microstructural techniques. Primary hot reversing-mill rolling produced static recrystallization (SRX) between every pass to significantly finer grain size. Hot torsion showed that with lay-on temperature and rate of reduction suited to gradual precipitation of minor additions of Nb, the austenite grains would become highly pancaked; the existence of very fine subgrains along the grain boundaries (GB) could be deduced from tests on stainless austenite. The HSLA strip had to be water-jet cooled immediately to prevent SRX at austenite GB and ensuring complete transformation to ferrite avoiding grain growth after coiling. Confirmation on old mills and successful product led to the design of more flexible mills for wider range of compositions and products. A significant one was auto bumpers that reduced crash damage. More crack-resisting compositions were developed for strip welding into line pipe for arctic oil transport. Lower metal consumption and easier fabrication has resulted in more sustainable welded bridging.

Jan 1, 2015

By Neville Jordison

Indirect, gravity flow, heat exchangers have become a well established technology in mineral and metallurgical process plants. The technology is a conventional heat exchanger using high efficiency plates, with a free flowing bulk solid on one side of the exchanger and a fluid on the other side. This simple concept leads to many opportunities for achieving greater energy efficiencies in process plants. Indirect heat exchange is much more efficient than direct heat exchange using air such as in a fluid bed or rotary device. When air is used directly, large fans are required, it may also be necessary to chill the air, both high consumers of energy. By contrast, using water as the cooling medium requires only low horsepower pumps, typically only 10% of fan HP. Furthermore there are no stack emissions with the requirement for removal of dust or emissions. Indirect heat exchange also creates the opportunity to recover energy. This can work in two ways: energy can be recovered from a hot bulk solid, to heat pressurized hot water for steam generation or preheat air. Alternatively recovered energy from elsewhere in the plant in the form of hot water, steam, air or thermal oil can be used to preheat a bulk solid.

Jan 1, 2011

By Erik Q. Dahl

The strength of green and sintered pellets during reduction under various conditions in a laboratory kiln has been investigated. Equipment and test methods are described, together with the results obtained. The strength of sintered pellets drops sharply when the reduction starts, and goes through a minimum at the 70 per cent oxidation level. At more advanced reduction, the strength increases with increasing metallization. Successful use of green pellets as kiln feed requires that more attention be paid to the pellet preparation than is necessary when producing pellets for separate sintering. In particular, the ores have to be ground to a greater fineness. The initial strength of green pellets is low. Below the 70 per cent oxidation level, however, the strength of these pellets is about the same as the strength of sintered ones. Additions of such materials as silica, limestone and anthracite coal; within reasonable limits, affect the strength only slightly.

Jan 1, 1966

By N. Djilali

Many of the transport phenomena encountered in proton exchange membrane fuel cells occur intrinsically at the microscale level. Physically representative models that fully account for the salient physico-chemical and transport processes in PEM fuel cells are necessary to achieve truly predictive models that can be used with confidence to: (i) gain a better understanding of in-situ processes and couplings, (ii) explore new concepts, and (iii) support design and optimization. The development of more general, rationally based macroscale models requires use of knowledge on the microscale level to provide guidance, and to determine the required parameters and coefficients (model "constants"). In this paper we present a new membrane transport model, the binary friction membrane model (BFM2), recently developed to account for coupled protonic and water transport in polymer membranes. This general model is based on rational and physical consideration, removes several of the limitations of the empirical models used to date, and is formulated for all purfluoro-sulfonic acid membranes. The use of the BFM2 in a fuel cell model is illustrated highlighting significant performance predictions compared to existing empirical model. The second part of the paper addresses the fundamentals of two-phase transport in hydrophobic gad diffusion media. Computational and experimental visualizations resolving the microscale dynamics of water transport between the fibres of a GDL are presented, revealing transport mechanisms that are, contrary to assumptions used to date, dominated by fingering and channeling.

Jan 1, 2005

By Mark Rantapaa

Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the Autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the Open Pit and Process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput. Better fragmentation and a subsequent increase in mill throughput were achieved through the use of: 1) Electronic caps for more precision and flexibility, as well as for allowing extremely fast shots. 2) Explosives with a higher velocity of detonation (VOD), to provide for improved shock energy. 3) Improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by six tph in 2003 due to the improved fragmentation of the hard ore. Barrick Goldstrike?s D2M initiative includes roaster ?hard ore? (BWI >17), as well as autoclave ?hard ore? (BWI >15). Approximately six million tons of D2M material is expected be shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs.

May 1, 2003

By A. I. A. Salama, M. W. Mikhail

"A comprehensive software package has been developed at the Western Research Centre to meet many of the coal preparation requirements in the Canadian coal industry. This package performs three main functions: (1) data handling and manipulation; (2) data analysis, including the generation of washability data, performance evaluation and prediction, density and size modelling, evaluation of density and size partition characteristics, and attrition curves; and (3) graphics output.The software described in this paper is potentially a valuable tool for coal preparation plant engineers and operators for evaluating process performance and adjusting plant density separator cutpoints. Moreover, the analytical laboratory technician could find this package very useful in manipulating and presenting laboratory results."

Jan 1, 1997

By Ben Bradshaw

Context ? Community engagement has become an increasingly significant and challenging part of mineral exploration and mine development; indeed, opposition from communities proximate to a proposed mine site has been known to derail technologically- and financially-sound projects. ? These cases suggest that mining firms need to better understand how to engage constructively with local communities in the pursuit of their claims. ? While a range of publications exist promoting various community engagement strategies, these recommendations, when viewed as a whole, are disjointed and largely untested in real development contexts. Aims of Presentation 1. Synthesize industry, NGO, government and academic publications focused on community engagement best practice in order to highlight those practices that are most commonly recommended. 2. Review the (Canadian) mining industry?s experience with some of these strategies based on existing case material in order to identify the extent to which commonly prescribed strategies are used and validated in practice.

May 1, 2010

By Christiaan Zeilstra, Jan van der Stel, Koen Meijer, Gerard Louwerse, Tim Peeters

The steel industry is producing about 5% of the world wide CO2 emission. Therefore the European steel industry has defined a research program to reduce the CO2 emission by 50% per ton: ULCOS. Since its start in 2004 ULCOS has identified four technologies for further development. Two of these technologies which produce liquid hot metal are discussed. The ULCOS blast furnace is based on recycling of decarbonated topgas and the capture and storage of CO2. The concept has been demonstrated during three campaigns at LKAB EBF in Luleå, Sweden. The smelting reduction process HIsarna is a combination of the cyclone-technology and Hismelt. The process has been demonstrated successfully in four campaigns at a pilot installation on the IJmuiden steelmaking site.

Jan 1, 2015

By N. Dobrin, R. Sheinman, Y. V. Kokotov, L. N. Braginsky

Increasing the production of a Mixer-Settler unit requires either increasing flow rates or increasing extractant concentration. The mixers still have to ensure complete emulsification and to maintain high values of specific interface surface area in order to provide a high rate of mass transfer. Theoretically, an increase in mixing intensity can support increased flow rates without reducing extraction efficiency. Unfortunately, conventional pump mixers and mixing systems create small droplets that do not separate easily. As pumping action and mixing intensities are increased, the quantity of small droplets increases. We describe the development and industrial application of a novel mixing system for efficient mass transfer without forming significant quantities of small droplets, targeting both high mass transfer rate and low entrainment values.

Jan 1, 2014

By A. O. Sfriso

"Numerical modelling is becoming universal in rock engineering practice. Most applications focus on the prediction of failure loads of 2D problems, where the numerical models are useful extensions to analytical methods and experience-based design criteria. For 3D problems and problems where the assessment of serviceability indicators – displacements, ground-structure response, etc. – are of importance, the selection of the constitutive models themselves and the implications of the selection of material parameters may have a very heavy impact on the reliability of the model outcome and its predictive capability.This paper overviews basic common aspects of constitutive equations used in practical rock engineering and summarizes some challenges that are frequently observed when reviewing numerical models performed for routine problems in rock engineering. INTRODUCTIONNumerical methodsFrom a philosophical perspective models, either analytical or numerical, are idealizations of a perceived reality. For us engineers, models are just tools we use to guide our judgement and understanding of the problem in hand. When dealing with problems in rock engineering, we resort to a wide range of techniques:1. Closed form solutions like confinement-convergence methods for circular tunnels: these methods satisfy equilibrium and compatibility requirements at the cost of a crude simplification of the material behavior and geometry;2. Limit analysis methods, like bearing capacity formulas: lower bound methods satisfy equilibrium but sacrifice compatibility, and upper bound methods do the opposite. Material behavior must be simple, geometry admits limited freedom;3. Limit equilibrium methods, like method of slices for slope stability: they satisfy restricted forms of equilibrium, do not satisfy compatibility requirements, require simple material behavior but have a much greater flexibility on geometry;4. Numerical methods, where a mesh is employed to discretize the problem geometry: when properly formulated, these methods satisfy equilibrium and compatibility requirements and give reasonable approximations to the behavior of very complex geometries and construction sequences. Very little restrictions remain on geometry and material behavior, but the cost of calibrating the material parameters can be very high."

Jan 1, 2015

By M. Matthias

A study, part of a doctoral dissertation (Matthias, 1991), was conducted during 1987 and 1988 to establish the means by which professionals assess and maintain their competence during the various stages of their careers. The study elicited responses from fifty-nine subjects representing engineering, pharmacy and medicine (twenty subjects from engineering, nineteen from pharmacy and twenty from medicine) on their perception and assessment of continuing competence. The findings revealed a wide variation of how professionals perceived their continuing competence and the means they adopted to keep current. The implications of the study are significant for adult education practice and theory building. The author strongly believes that now, more than ever, engineers must take ownership of their careers and professional development activities. While management and supervision have a key role to play, it is the engineer, who is ultimately responsible for the scope, planning and implementation of her/ his professional development needs. An example from one high technology company will illustrate these points.

Jan 1, 1999

By R. B. Hyde

"Severe drilling conditions and difficult mud problems are briefly out-lined as the major cost items in all production operations. The chief problems discussed are abnormal pressures, high temperature, trouble-some shales, and low rates of penetration. These problems have been eliminated or greatly reduced in many areas by• the proper application of recently developed drilling mud products and techniques. These severe problems and their solutions are discussed generally: the application of high-density weighting materials to overcome abnormal pressures; surfactant muds with sodium polyacrylate as a solution for deep and high-temperature drilling; shale control muds and new dispersants for severe shale problems; and low-solids emulsions and •extreme-pressure lubricants for greatly improved rates of penetration."

Jan 1, 1959