Search Documents

By A. Anderko, V. G. Papangelakis, G. Moldoveanu, G. Azimi, M. Carlos

"OLI Analyzer is a software package that uses the powerful Mixed Solvent Electrolyte (MSE) model to simulate the behavior of multicomponent electrolyte solutions from infinite dilution to the limit of fused salt, and from temperatures below the freezing point up to near critical temperature of the mixture. The software also allows the creation of thermodynamic parameters for new chemical systems unavailable yet in public-domain or commercial software databanks. This communication reviews the basics of the model and provides some examples of modeling hydrometallurgical applications with emphasis on high temperature applications, including calcium sulfate scale formation in autoclaves, high temperature pH inference and iron control. INTRODUCTIONModeling of electrolyte systems has been of particular interest to various industrial processes, such as separation processes (e.g., solution crystallization, extractive distillation, seawater desalination or bio-separations), environmental applications (e.g., gas treatment, wastewater treatment or chemical waste disposal) and hydrometallurgy (e.g., pH control and neutralization, iron control, scaling and fouling of equipment). Using a chemical model, time-effective predictions of various properties of electrolytes can be obtained, which is beneficial not only during process monitoring, but also during process optimization and process scale up. As a result, pilot scale studies can sometimes be eliminated where budgetary constraints exist. Development of such a powerful model requires the use of a speciation-based model, in which solution chemistry is explicitly addressed (as compared with some models that treat electrolytes either as undissociated or fully dissociated systems), despite being computationally challenging. In addition, as a feature of electrolyte systems, speciation equilibria inherently influence the phase equilibria due to complex formation, ion pairing, and acid-base reactions. Therefore, how the electrolyte solutions behave at various conditions may differ significantly due to the non-ideality, which must be carefully addressed to obtain a model that is applicable to a wide range of conditions such as concentration, temperature, pressure and solvent system."

Jan 1, 2012

The Curtin University Gold Technology Group has been involved in surveying, modelling and optimisation of batch centrifugal concentrator type gravity circuits and CIP/CIL circuits for nearly two decades. The most commonly asked question regarding gravity recovery is, “What is the benefit of a gravity circuit”, which can be hard, if not impossible, to quantify. With the help of the AMIRA P420 Project’s Integrated Liberation Leach Model (ILLM) it is now possible to evaluate the effect of gravity recovery on total gold recovery when changes are made to the grind size, gravity and/or leach/adsorption circuits. This paper demonstrates how the ILLM can be used to determine the net benefit of introducing or modifying a gravity circuit and assess the effect of operating conditions (grind size, coarse gold size distribution, leach residence time, carbon activity, etc.) on plant performance.

Jan 1, 2017

By D. C. McDonald

"IntroductionTHE GIANT YELLOWKNIFE property is on the west side of Yellowknife bay, Great Slave lake, N.W.T., some 600 air miles north of Edmonton. This paper deals with the underground development and mining of the complex system of orebodies which have produced, in the first fifty-six months of operation (May, 1948, to December, 1952), 652,464 tons of ore with an average grade of 0.80 ounces of •gold per ton (1).The mine has been developed from three vertical shafts designated A, B, and C. Figure l shows the positions of these openings with respect to the known ore-bearing zones and the surface plant.A shaft was sunk to a depth of 522 feet in 1945-46, primarily as a prospect shaft for investigation and development of the East Zone orebody. Drifting was carried out on the 200-and 325-foot levels. Before this development had been completed it was clear that the funds immediately available made it imperative to get revenue from production as soon as possible. By the beginning of 1946, the remarkably high-grade character of the ore in the present B Shaft area had been established by surface drilling, and the decision was made to obtain initial production from this source. Since known orebodies at shallow horizons were to be developed quickly, the choice of a suitable rock outcrop for the shaft was something of a problem."

Jan 1, 1953

By Earl Sweet

This overview of economic and financial market prospects examines the current and future state of the global and Canadian economies with a focus on commodities. Housing prices and global conflicts all have effects on the overall economy and metal prices and mining developments in particular. This presentation outlines where we are today and where the author and BMO see the economy moving over the next few years.

Jan 1, 2016

By B. Calver, D. J. M. Farnsworth

"As open-pit operations expanded at Pine Point, hydraulic aquifer evaluation was undertaken to establish the criteria necessary for the design of a feasible dewatering system.The extreme climate of this northern location dictated that the ore zone under extraction be rendered as dry as possible to minimize freezing effects. The design and implementation of such a system necessitated detailed hydraulic evaluation, and the problems that occurred are typical of those inherent in open-pit mining operations in northern areas.The paper describes the problem solution as approached from a mine engineering point of view, with particular reference to the practical aspects of operation and installation. The hydrological analysis used is simple and readily applicable to most open-pit dewatering problems."

Jan 1, 1969

By J. G. A. Stevenson

GENERAL Location of Property THE Stirling zinc-lead-copper deposit is in Richmond county, Cape Breton, about a quarter of a mile southwest from Stirling P.O., and some 45 miles southwest from Sydney. The property is accessible by road for at least nine months of the year, and during the navigation period coastal boats maintain a service touching at the port of Fourchu, eleven miles from the mine. When flying conditions permit, the Cape Breton Flying Club, of Sydney, will carry passengers to or from the property, a service which has been particularly advantageous on two occasions when hospitalization was urgently required. The Company has mining rights on leases Nos. 73-74, 78-80, and 101-104, inclusive, and owns 166 acres at Stirling and one acre at Fourchu. The ore deposit is in lease No. 73. History The Stirling deposit was discovered in the 'nineties', probably about 1895. The original discovery is said to have been made in the bed of Copper creek, which traverses the ore-zone. For a number of years, indifferent development work was carried on with a view to copper production only, and it was not until1915-16 that attention was directed to the possible production of zinc. Previously, the ore had been considered too complex for metallurgical treatment. During the period 1916-24 several operators attempted to develop the property, among them being the Stirling Exploration Company, Stirling Mining & Smelting Company, New Jersey Zinc Company of New York, Hayden & Stone Company of Boston, and The Eastern Mining & Milling Company. Up to 1924, the work was limited mainly to trenching, stripping, ? diamond drilling, and shot drilling.

Jan 1, 1937

By A J. Kyle

After a brief description of the shaft and surface facilities, this paper describes the planning for the mining operation, the selection of equipment the general method of mining and the sequence of operation. All of the major items of equipment are described, including the components of the power system. The detailed planning is reviewed -from the shaft sinking to the three-shift mining operation. Excavation and equipment changes, as well as long-range planning, are al o di cussed. Introduction THE successful completion of the Yarbo No. 1 shaft of International Minerals & Chemical Corporation (Canada) Limited in July, 1962, added a new type of mine to Canada&apos;s many producing operations. IMC Esterhazy is a unique mining operation in Canada; in fact, it is unique to potash mining in general. Not only is thi&apos;3 a trackless operation utilizing shuttle cars and belt conveyors in its material handling systems, but it excavates all of the ore with continuous boring machine<:;.

Jan 1, 1964

By Arthur A. Cole

Although the metal silver has been known and prized from very ancient times, it is in the New World that the greatest silver camps have been found. This is shown in the following comparison: [] For the last few years, the World&apos;s annual production of silver has averaged about 240 million ounces troy. Of this total, the North American Continent contributes approximately three quarters, Mexico leading with 38 per cent, followed by the United States with 27 per cent, and Canada with nearly 9 per cent.[] Of the largest silver producers in Canada, the Sullivan takes first place. Although primarily famous as a lead and zinc mine, it produced, in 1926, more than 4.5 million ounces of silver. The Premier mine, in northern British Columbia, produced more than 3 million ounces. In Ontario, the largest producers in 1926 were the Nipissing mine, .with 1.9 million ounces, and the Keeley mine, with 1. 7 million ounces. The Mining Corporation produced 1.1 million ounces from mines in the Cobalt district proper, and an equal amount in South Lorrain; while from the Castle-Trethewey mine, in Gowganda, there was an output of slightly less than one million ounces.

Jan 1, 1927

By Corby G. Anderson

"Laboratory testing using industrial electrowinning solutions was performed to determine the best Faradic cell efficiency for copper cathode recovery. The variables tested were solution flow rate, recycle ratio, reagent addition combinations of guar and thiourea, and addition amount of acid mist suppressant CAL FAX DBA-70. The ideal flow rate was determined to be 37.85 litre/min. Additionally, the ideal recycle ratio was determined to be 10:1. The reagent addition scheme from testing which showed the highest efficiency was with 680 g/tonne guar of cathode copper won and with 135 g/tonne thiourea of cathode copper won. These values for reagent addition only reflect the best efficiency and should not be assumed to be the best reagent concentration for copper purity. The amount of foaming agent that showed the best efficiency was the test with 2 ppm of foaming agent. Again this amount of reagent is based on efficiency and should not be taken as the amount of reagent that does the best acid mist suppression. Additional proprietary surface characterization work indicates these additives may have enhanced the cathodic reduction surface morphology of some noble minor impurities. Subsequently, these operating parameters were introduced into the plant operation and proved successful after their implementation.BACKGROUNDCopper electrowinning has become a dominant technology for the production of marketable high grade copper cathode products. The literature is robust with applications, optimizations, additives and developments in this field (e.g., Classens & Harris, 1990; Pfalzgraff, 1999; Tozawa, Su, & Umetsu, 2003; San Martin, Otero, & Cruz, 2005; Houlachi, Edwards, & Robinson, 2007; Romero, Avila, Fester, & Yacher, 2007; Marsden, 2008; Beukes & Badenhorst, 2009; Vainio & Weatherseed 2009; Bender, 2010; Joy, Staley, Moats, Perkins, Uhrie, & Robinson, 2010; Khouraibchia & Moats, 2010; Moats, 2010; Rutledge & Anderson, 2015).Tests of forty hours duration and at room temperature were performed for this project using samples of actual industrial electrowinning solutions. These industrial solutions were comprised of 60 g/L Cu plus 65 g/L Ni, 3 g/L Fe, and 30 g/L free sulfuric acid. Other confidential minor impurities were also present including some solubilized precious metals. The testing apparatus utilizing stainless steel anodes and cathodes is illustrated in Figures 1 and 2."

Jan 1, 2016

By Daniel Hodouin, Claude Bazin

"This paper examines the economic advantages of tuning the operation of a differential Cu-Zn flotation circuit as a function of metal prices. Three operating strategies are considered in the analysis: 1) the operation of the circuit at planned copper and zinc concentrates grade with maximum recovery of both metals; 2) the operation of the Cu circuit at maximum copper smelter return per ton of ore and of the Zn circuit at a maximum zinc smelter return per ton of ore; and 3) the operation of the circuit at maximum copper and zinc smelter return per ton of ore. The second strategy tunes the copper circuit independently from the zinc circuit, while the third strategy tunes both circuits simultaneously IntroductionMetal prices play a very important role in the mineral industry (Malhotra and Dowling, 1991). In many cases, metal prices can be the basis for the GO/NO GO decision of a mining project (Malhotra and Dowling, 1991; Apostolides, 1983; Davis, 1996). This direct impact of metal prices on company revenues is highlighted in many annual reports. The 1995 Noranda Annual Report indicates that a variation of 10% of the copper price impacts its yearly revenues by $25,000,000. Some mine operators claim to mine stopes as a function of metal prices (Liimatainen, 1996; Hartman, 1992). This impact of metal prices is also recognized by mill operators that seek strategies to tune ore processing circuits to maximize revenues from the concentrate they sell to smelters (McKee, 1991; Barker et al., 1989; Hales and Ynchausti, 1994; Cipriano et al., 1995). In many cases the problem of tuning the operation of an ore processing circuit is complicated by the fact that the ore contains two or more valuable metals which have to be recovered into separate products. The Agnico-Eagle (Robitaille and Cousin, 1995) and Barrick East Malartic (Pelletier, 1996) Cu-Au mines are examples, as well as the Cu-Pb-Zn Brunswick mine (Shannon et al., 1993) or the Cu-Zn Louvicourt (Whiteway, 1995) and Selbaie (Wright, 1995) mines."

Jan 1, 2000

Adaptive Processing as proposed in geometallurgy has to rely on spatially interpolated information on geometallurgical parameters like phase composition, size distributions of particles of different phases, grain shape parameters, and portions of value elements in different grains. Using the geostatistically predicted values for adaptive processing, e.g. for the selection of milling diameters, thresholds in physical separation, or choices on using an extra pre-separation step, is typically not optimal. Mathematically this effect is introduced by two forms of nonlinearities: 1) The nonlinear scales of compositions, distributions, and shapes have special properties with respect to geostatistics. Classical geostatistics creates some artefacts for these nonlinear scales. On the other hand, modern geostatistical procedures adapted to these scales do not provide unbiased results with respect to linear transformations of the data (e.g. biased block estimates). 2) Neither economic nor ecological effects (e.g. monetary gain) of processing decisions are linear in the interpolated geometallurgical parameters. These nonlinear transforms are not unbiasedly estimated by the likewise transformed unbiased geostatistical predictions of the geometallurgical parameters. Furthermore, we need to optimize the conditional expectation of the gain, rather than obtain an unbiased estimate. Standard geostatistics as such does not provide the "right sort" of estimates for adaptive processing. A nonlinear kriging procedure is needed to approximate the nonlinearities mentioned before. We propose to solve these problems simultaneously using a nonlinear geostatistical technique for predicting the target function (the monetary gain), rather than to predict the geometallurgical parameters and compute the gain from them. The optimization can then be performed directly on this estimated function. It can be shown that this optimization performed on the conditional expectations, not on unbiased predictions, would yield the best possible processing choice. We propose a procedure choosing the processing parameters on an approximation of the conditional expectation. The difficulties with the classical approach and the effectiveness of this new approach are illustrated by a simplified simulation example with a single processing parameter and a simple dependence on the microstructure.

Aug 1, 2013

By Desmond Y. M. Lee

This paper presents a procedure to prepare input for the computerized pit design system at Iron Ore Company of Canada. The procedure is simple and requires very little training. Also, it is general enough to accept both bench (horizontal cross section) maps and section (vertical cross section) maps. The output of this procedure is data which represent blocks of ore and waste with dollar values based on mineral content. The ultimate pit design is presented in printer-generated graphs, with numbers indicating the depths of pit bottom walls. Roads are added manually by the engineer with the aid of other computer programs. Section maps and bench maps are also printed as part of the output of the ultimate pit design.

Jan 1, 1978

By S. Feinstein, I. Reznik, Y. H. Hatzor, O. Shitrit, Y. O. Rosenberg, H. J. Vinegar, S. Nguyen

"We report the effects of porosity and total organic carbon (TOC) content on the mechanical behavior of organic-rich chalks, based on laboratory measurements. The organic-rich chalks are from the Senonian Ghareb and Mishash formations. This deposit is an immature oil-prone source rock, about 300 meters thick, situated at shallow depths (several hundreds of meters) in the Shefela basin in central Israel. The study is based on core data collected from the Zoharim borehole.Three main phases comprise the bulk volume of this rock: 1) carbonate mineralogical phase (predominantly calcite); 2) pores (mostly saturated with brine); and 3) solid organic phase (type IIS kerogen). The mechanical effects of porosity (23-45%) and TOC (4-19%) are evaluated based on bulk incompressibilities vs. volumetric fractions analysis. Volumetric fractions of mineralogical and organic phases were obtained by porosity, density and TOC measurements. Saturated rock bulk moduli were measured through ultrasonic velocity measurements. Saturated rock bulk moduli correlate best with the sum of kerogen and pore volume fractions, rather than each of them separately. The volumetric fractions were also used to define the range of bulk modulus of the organic-rich chalk, using the Hashin-Shtrikman upper and lower bounds. Based on Marion's Bounding Average Method (BAM), the normalized stiffness factor of the chalk averaged at w=0.197, indicating a soft pore geometry. Using the average normalized stiffness factor, the BAM predictions showed excellent match with the saturated rock bulk modulus and the sum of kerogen and pore volume fractions. Based on our findings, it is inferred that kerogen grains do not support the solid skeleton but are distributed between the minerals grains. We also propose here a straightforward approach for calculating the Hashin-Shtrikman bounds, based on TOC and porosity measurements. The mechanical effects of porosity and TOC indicated here are very important for the understanding of the influence of immature kerogen presence in highly porous chalks, as the Ghareb and Mishash formations."

Jan 1, 2015

By Z. Q. Liu, J. M. Du

"On the basis of analyzing current design and applications, the structure form, working loads and design principles of shaft sinking headframe are summarized in this paper. To overcome the insufficient bearing capacity and geometry size of the finalized shaft sinking headframe in China, a series of new large shaft sinking headframe were developed under vertical shaft construction conditions of maximum net diameter of 12.0 m and maximum depth of 1200 m. The new series shaft sinking headframe include two sets (with single sheave platform and double sheave platform), three dimensions (optimum shaft diameter <8.0 m, 8.0-10.0 m, and 10.0-12.0 m, respectively) for each set, and has innovation and optimization on structure of the sheave wheel platform (MU type) and bracing frame (REN and ZHONG type). The largest new shaft sinking headframe can arrange up to 4 hoisting equipment simultaneously and has bearing capacity more than 10000 kN. Two of the new shaft sinking headframe were successfully applied in practical engineering, such as the Hulusu auxiliary shaft, the Dahaize 1# auxiliary shaftand Sishanling auxiliary shaft. These applications showed that the new shaft sinking headframe has sufficient bearing capacity and reliable applicability. The new shaft sinking headframe could provide an effective guarantee for safety and efficiency sinking of deep-large shaft in the future.INTRODUCTIONShaft sinking headframe is one of the basic shaft sinking structures and it is mainly for hanging hoisting containers and sinking facilities in sinking a vertical shaft (Yu & Shi, 1991; Wang, Jing, & Liu, 2007). Currently, 7 types of steel pipe sinking headframe are used in China, which are mainly finalized by the Ministry of Coal Industry of China (Wang, 1988). As shown in Table 1, V-type is the largest of them and it is only suitable for sinking shaft of diameter less than 8 m and depth less than 1 000 m(Yang, 1982). However, with the increase of mining depth and scale of mineral resources in China, the diameter and depth of newly built vertical shaft are increasing continuously (Xie, Zhou, Xue, Wang, Zhang, & Gao, 2012; Qi & Pu, 2013). At present, the maximum net diameter of vertical shaft is close to 12 m, and the maximum depth is more than 1600 m (Yang & Chen, 2015; Xu, Yang, Liu, & Qin, 2015). The shaft sinking headframe has become the main restrictive factor for the development of sinking equipment, such as the height of muck discharging platform cannot meet the usage requirement of hydraulic umbrella driller, the size of sheave wheel platform is difficult to arrange the increasing hoisting and suspension equipment, the bearing capacity is insufficient to meet the needs of multiple hoisting loads in sinking a deep-large shaft, etc. Therefore, development of new shaft sinking headframe for deep-large shaft (>1000 m in depth and 8~12 m in diameter) is urgently required for China and also the whole world."

Jan 1, 2019

By I. A. Kovalevska

Considered problems: elaboration and implementation of resource-saving technologies, low-cost support systems improvement, openings security and support, based on wallrock condition control with supreme implication into the rock pressure occurrence counteraction work. Results of analytic and underground investigations using computer simulation of the finite elements in order to calculate stressstrain state of the multivariable geomechanical systems are presented. Solutions of concrete objectives are found using spatial geomechanical model of solid motion around openings, considering real geomechanical parameters formation of support forms with proper conditions of their contact and real mechanical characteristics. Ultimate solutions of resource-saving technologies implementation based on the analysis of multivariate vertical, horizontal, and reduced stresses components calculation and also near-contour rock, support bearing components and security constructions movements are found. Results of experimental investigations of combined supports and security constructions, which increase openings&apos; stability in difficult conditions of flat coal seams are presented.

Aug 1, 2013

By Piotr Malkowski

Studies on the properties of rocks heated to high temperatures are rather rare. Such research is occasionally conducted for example; in areas around nuclear power plants. The national Polish coal gasification (underground coal gasification, or UCG) project has, however, forced the analysis of the geomechanical properties of heated rocks in the vicinity of a designed geo-reactor. Ukrainian experience with UCG show that rocks up to 2 m from the burned coal seam be at a temperature > 600ºC. Such a high temperature will undoubtedly influence their physical properties. This paper presents studies on the strength and deformation properties of carboniferous rocks in the Upper Silesian region, where the UCG process is planned. Three types of rocks were tested: claystones, mudstones and sandstones. Laboratory tests of these rocks evaluated compressive strength, elastic modulus and weight loss. An evaluation of the results of the tests comparing the thermal conductivity of rocks and their specific thermal capacity was then carried out. All of the rocks studied were heated to 300, 600 and 1000ºC, and also evaluated at room temperature. This procedure shed new light upon the behavior of heated rocks in relation to their distance from the designed geo-reactor. The test results presented were developed within Research Task No. 3 ?Developing a technology of coal gasification for efficient production of fuels and electric power?, financed by The National Centre for Research and Development under strategic research and development programme ?Advanced Technologies for Energy Generation.?

Aug 1, 2013

By Robert P. Harrison, Marie-Christine Patoinel, Kristian E. Waters

This paper describes a collaboration between McGill University and Hatch Ltd. to expose undergraduate students to real-world industrial projects. As part of the final-year design course, the students receive a detailed lecture on Scale-Up of New Technologies&apos;, including seven case studies drawn from over fifty years of full-scale industrial projects. The students are taught the basic concepts of scale-up, including the limits of pure theory and the need for empiricism. Insights from real scale-up failures and successes are fictionalized as Projects A, B, C, etc. The students are then asked to identify the guiding principles that can be distilled from these case studies.

Jan 1, 2011

By R. E. Johnson

Seventy years after the start of the Industrial Revolution in Great Britain, as reckoned from Arkwright&apos;s water frame patented in 1769, there was a significant development of the metallurgical industry in Virginia. In Britain, crucible steel had been rediscovered by Benjamin Huntsman in 17~0, and this made spring and tool steel more generally available. The metal-turning, screw-cutting lathe, including the basic principles recognized in today&apos;s engine lathe, was developed by Henry Maudslay about 1797. Wrought iron, as manufactured by Henry Cort&apos;s process patented in 1784, was readily available. Richard Trevithick&apos;s highpressure steam locomotive had met its test on the Pennydarren tramroad in 1804, and George Stephenson had built his famous Rocket, along with several other locomotives, at Newcastle around 1828. Puddling furnaces and a rolling mill had been placed in operation at the Tredegar Iron Works in Glyn Sirhowy, Monmouthshire, Wales, in 1807. In the United States, expanding commerce and a growing population resulted in continuing development from the Chesapeake to Virginia&apos;s Blue Ridge, and this demanded improved means of transportation. Ore deposits rich in hematite had been found in Virginia&apos;s Piedmont during the Colonial period, and a number of blast furnaces now dotted that area. The products of these operations were mostly pots, kettles, stove parts and like items for local trade. The James River and Kanawha Canal was incorporated in January 1785. Its eastern leg, winding along the slope of the high bluffs overlooking the river, was completed about 1800. About two dozen railroads were chartered in Virginia between 1830 and 1837. With expanding population and steady industrial development came a need for metallurgical products. Throughout the eastern United States, numerous metallurgical enterprises sprang up, and many of these flourished. The purpose of this article is to outline the development of one Southern metallurgical company, the Tredegar Iron Works, which was to have a significant impact on the industrial development of Virginia and the fighting of the American Civil War. Although the Tredegar Iron Works no longer exists, remnants of the early operations have been restored, and the current status of the site is also presented.

Jan 1, 1999

By T. Joseph, E. Zheng, M. Curley

"Hydraulic transportation efficiency and production optimization are considerations in the surface extraction of Athabasca oil sand deposits. To reduce the dependence on haul trucks, it is possible to extend the hydraulic transport system to production faces using a mobile at-face slurry system (AFSS). The flexible arrangement of connected pipelines transports slurried minerals from the mining face to the processing plant. An experimentally verified mathematical model indicates the friction loss of oil sand slurry associated with the AFSS. Laboratory-scale testing enables extended analyses for examining pipeline slurry transport in an oil sands environment.RÉSUMÉ L’optimisation de l’efficacité du transport hydraulique et de la production sont des considérations importantes dans le domaine de l’exploitation à ciel ouvert des gisements de sables bitumineux de l’Athabasca. Afin de réduire la dépendance envers les camions de transport, on envisage d’étendre le système de transport hydraulique aux fronts de taille à l’aide d’un système mobile de transport des matériaux sous forme de boue à partir du front de taille (AFSS, de l’anglais at-face slurry system). L’organisation flexible des conduites reliées permet le transport de minéraux à l’état de boue du front d’exploitation jusqu’à l’usine de traitement. Un modèle mathématique vérifié de manière expérimentale indique la perte de charge par frottement des schlamms provenant du traitement des sables bitumineux associée à l’utilisation de l’AFSS. Des essais en laboratoire permettent de mener des analyses approfondies portant sur le transport de boues dans des conduites dans un environnement de sables bitumineux. INTRODUCTIONObjectives and scope of studyThe at-face slurry system (AFSS) concept has become a competitive means for materials handling to optimize haulage system efficiency and cost. The mobile and flexible arrangement of the AFSS introduces a unique set of hydraulic transport problems. This paper will focus on developing the mathematical models governing the friction and head losses within the AFSS concept.Background of the problemLarge-capacity shovels and dump trucks are increasingly used for excavation, loading, and hauling in the operation of surface mining. Production cost and efficiency optimization are demanded during the Athabasca oil sands (Alberta, Canada) mining process to secure North America’s energy supply. Increasing haulage distances, rugged terrain, and a constrained mine environment are conditions that will reduce the effectiveness of the shovel-truck haulage system (Frimpong, Szymanski, & Changirwa, 2003). In such conditions, the tire heat index and weight, distance, and time limits for truck haulage can be exceeded, simultaneously creating extreme tire wear and high maintenance costs. In addition to low production cost and equipment effectiveness, a mining environment also requires efficient waste-material recycling and distribution. Waste materials need to be recycled from the processing plant to a new destination such as a tailings dam, or replaced in mined-out areas such as backfill. The Athabasca oil sands configuration and location characteristics result in a mining environment that would benefit from flexible pipelines for constant production and an efficient waste-material recycling process."

Jan 1, 2017

By Dorothy Walters

As an increase in the number of producers alters fact ors affecting supply, long-term prospects in traditional markets for many minerals weaken. At the same time, conflicts between national and international objectives undermine existing competitive elements in mineral markets and Canadian costs escalate. Such changes may dramatically alter the environment in which the mining industry operates.

Jan 1, 1979