Search Documents

By Paul Hughes

This paper summarizes current underhand paste backfill mining as applied to Goldcorp Inc?s Red Lake Mine, Newcrest Mining Ltd?s Kencana Mine and the Lanfranchi Nickel Mine as well as ongoing research at the University of British Columbia?s Norman B. Keevil Institute of Mining Engineering. The Red Lake Mine utilises a 6 m wide undercut with a 2 MPa unconfined strength paste in order to selectively mine its high grade, high-stress orebody. Kencana?s orebody is located in a poor rock mass environment. An 8 m wide, 2 MPa unconfined strength paste sill allows a safe working condition for its high grade orebody. The Lanfranchi Nickel Mine utilises a cable-supported, 2 MPa paste, with 12 m span sills, to optimize the mining of the squeezing rock mass. This paper details the rock mechanic hazards, ground support techniques, paste practices and unique conditions for each mine. Further, an update of ongoing research at the University of British Columbia, focussing on the optimization of safe mining in underhand cut-and-fill mining in high-stress/weak rock masses, is presented.

May 1, 2011

Infrared spectroscopic data collected using HyloggerTM technology is being used to assess the mineral composition of Archean iron ore bedrock and Cenozoic detrital units in Western Australia’s Pilbara region. Analysis of infrared spectra enables quantification of: (1) composite iron mineralogy, (2) composite clay mineralogy, (3) hydrous silicates and (4) carbonate mineral abundances. Stratigraphic and rock mass unit logging of core has identified several detrital and bedrock units recognisable across the Pilbara. However, due to alteration related to mineralisation, weathering and later stage precipitate overprinting, it can often be difficult to assess the detrital-bedrock boundary and the occurrences of specific geotechnical units in the detritals and bedrock, particularly when using non-core drilling techniques and traditional geochemical assays. Infrared spectroscopic data collected concurrently on core from several sites has shown distinct correlation against existing unit subdivisions and associated geochemical parameters. Where infrared spectroscopic data have also been collected on rock chips recovered from reverse circulation infill drilling, these correlations allow robust geological and geotechnical models to be developed based on the typical mineralogical-geochemical signatures. The geotechnical sub-units identified in core can be readily distinguished using the various iron and clay minerals captured by the HyloggerTM technology as opposed to total iron, potassium, and alumina captured by geochemical assays. Further, some of the minerals targeted by infrared spectroscopic analysis (eg gibbsite, white mica, vitreous goethite) and their ubiquitous presence as the products of weathering, assist in recognition of various ancient weathering surfaces and help to define the origin of the material, whether bedrock or detrital. Overall, HyLogging of core and chips allows important mineralogy focussed data to be captured at minimal additional financial outlay. Correlations against geochemical unit identifiers are robust both within deposits and between deposits. Significant improvements in the confidence of geological and geotechnical models are attained.

Jan 1, 2015

By Z. B. Karshigina, Ye. G. Bochevskaya, E. A. Sargelova, Z. S. Abisheva

At the present time of depletion of reserves of high grade rare earth deposits, it has become necessary to involve low grade raw materials in the production. Among the rare-earth deposits in Kazakhstan, the most advanced one is Kundybai. The mineralogical composition of ore is represented by the minerals: a-quartz SiO2, kaolinite Al2(Si2O5)(OH)4, muscovite KAl2(AlSi3)O10(OH, F)2, albite Na(AlSi3O8), rutile TiO2, and hematite Fe2O3. It contains: 59.1–68.5% SiO2, 19.1–28.4% Al2O3, 7.2–10.3% Fe2O3, 0.51–0.84% TiO2, 0.10–2.32% CaO, 0.39–2.10% MgO, and some other elements. Rare earths are located in the clay part (kaolinite, goethite) in the ion-adsorbing form, and they are represented by the main ore mineral churchite - YPO4·2H2O. In the ore the amount of rare-earth elements (total REEs) varies from 210 to 600 ppm. Elements of the cerium group predominate (La, Nd, Ce, Sm, Pr) and the yttrium group is represented by Y, Gd and Dy. Extremely thin intergrowth and accumulation of REEs in clay minerals cause difficulties in their recovery using flotation and gravitation beneficiating methods. The purpose of this work is the development of an extraction method for the main mineral components of ore with transfer of the total REEs into the solution with high extractive efficiency. Results of the experimental work into high-temperature processing (hereinafter referred to as sulphatization) of ore by sulphuric acid with subsequent dual-mode water leaching of the sulphate product (sinter) are presented in this manuscript. The influence on the ore sulphatization process of some physical and chemical parameters: liquid-to-solid (L/S) ratio (0.36–0.86 cm3/g), temperature (100 – 500°?), concentration of sulphuric acid (3.0–18.62 mol/L) and duration (0.5–2.5 h) was studied. Optimal technological parameters of the process were determined to be: L/S ratio 0.36–0.46 cm3/g; temperature 500°?; concentration of H2SO4 9.0 mol/L; soaking time 1.5 h. Under these conditions it is possible to obtain extractions of ~ 85% REE, as well as 58% aluminium and 10% iron. XRD and IR-spectroscopy analyses were used to determine the material constitution of sulphated cakes obtained under optimal conditions. It was found that the primary minerals are quartz and muscovite; however different sodium aluminium silicates and albite minerals are present as well. In the future, it is proposed that the leach residue cakes are processed into precipitated silica (“white soot”).

Jan 1, 2016

By J. E. Nesset, S. R. Rao, J. A. Finch

"For base metal sulphides, iron rejection starts in mineral processing. This review focuses on changes in plant practice specifically to improve iron sulphide rejection by control of contaminant ion effects and discusses selected general innovations in mineral processing that can be expected to play a role. One group of changes to control contaminant ions is in size reduction (the use of stage grinding and inert stirred milling) and another is in system chemistry (order of reagent addition and exploitation of the flexibility of sulphoxy reagents). Plant examples illustrate the successes, indicating that there are several options available. The general innovations start by considering the new tools for measuring gas dispersion properties and quantifying froth characteristics by imaging. Examples of their application to improve concentrate quality illustrate the potential. Other innovations stress adapting geostatistics to model variation in milling and flotation response to provide feed forward control and rigorous application of statistical experimental methodology in plant test work. An example from one concentrator shows improvements in concentrate quality from application of basic principles can be impressive.INTRODUCTIONThe more iron control (rejection) that can be accomplished in mineral processing the lower the subsequent metal extraction costs and environmental implications of iron disposal, particularly in hydrometallurgical processes. Iron rejection has been a contributing target to periodic attempts to apply mineral processing to nickel laterites and bauxites but the prime application is control of pyrite and pyrrhotite (iron sulphides) in the treatment of sulphide ores by flotation. In this paper some new concepts and innovations introduced in sulphide flotation plants over the past ten years or so (i.e., since a previous review [1]) will be outlined with examples of how they have contributed to improved “iron control”.To increase rejection of iron minerals, first the recovery mechanism should be understood. There are four principal ones, two physical in origin: 1, via locked particles (i.e., flotation of composite particles due to insufficient size reduction to liberate the minerals) and 2, through entrainment in the water reporting to the float product (an unselective process); and two originating from a response to the system chemistry: 1, true flotation (i.e., iron sulphides becoming hydrophobic) and 2, as a result of iron sulphides forming aggregates with hydrophobic particles (e.g., ”slime” coatings). There has been considerable effort to diagnose which of these dominates iron sulphide recovery; in many cases it is due to “chemistry”, in particular true flotation. The flotation effect often appears related to contamination by metal ions [1]. This can reduce selectivity in two ways: 1, metal ion species may activate iron sulphides, or 2, cause general depression which demands more vigorous flotation conditions (e.g., additional collector) with consequent loss of selectivity. This is where the review will start, by considering ways to control contaminant ions."

Jan 1, 2007

By K. Mayhew, K. Murray

The CESL Copper Process was developed as a hydrometallurgical alternative to smelting and refining for copper sulphide concentrates. As the majority of such concentrates contain appreciable gold and silver values, effective recovery of these metals is essential to the economics of this technology. Unfortunately, conventional cyanide processing cannot be used on the residue from the copper process, clue to its unusual characteristics when compared with naturally occurring gold and silver ores. An abundance of elemental sulphur, as well as the presence of cyanide soluble copper, leads to the formation of both thiocyanate and copper cyanide which is detrimental to process economics clue to excessive cyanide consumption. This, however, can be reduced to acceptable levels by process innovations such as pressure cyanidation and cyanide recovery. This paper outlines the successful application of the CESL Gold Process to various gold-bearing copper concentrates from bench to demonstration scale.

Jan 1, 2011

By Nicholas Bonderoff, Amily Xu

The evaluation of battery electric vehicles (BEVs) in underground mines involves comprehensive business case analysis beyond just the capital and operating costs of the equipment itself. BEVs demonstrate benefits from an EHS perspective, reduced mine ventilation costs, lower energy operating costs, reduced overall GHG emissions (dependent on the source of electricity), elimination of DPM, lower equipment maintenance costs, and reduced cooling requirements in deep mines. When including batteries and supporting infrastructure, BEV capital costs are approx. 80% greater than that of diesel equipment. The project economics are highly dependent on the cost of electricity and diesel fuel, and these can vary widely depending on the location of the mining operation. Battery charging and swapping methodologies must be evaluated as there are a variety of approaches that can be employed which vary by manufacturer and type of equipment. Careful consideration of the cycle times, charging methodologies, and location of the battery charging infrastructure is necessary. Specific operating conditions must also be taken into consideration. For example, the time for blast gases to clear will be increased by reducing ventilation flow, and the potential impact on production needs to be evaluated. Similarly, the electrical distribution system needs to be evaluated for peak loading conditions when BEVs are charging. Criteria including maintainability, reliability, commercial availability, and performance need to be evaluated. BEVs have fewer components than diesel equipment and this correlates to lower overall maintenance costs, however, BEVs require maintenance personnel with specific skill sets in order to maintain the equipment. Battery lifecycle costs need to be considered as battery replacement incurs significant capital expense. Some manufacturers offer services to offset these capital costs through usage agreements. Recycling and disposal of batteries at the end of their lifecycles also need to be considered. With the increased selection of BEV equipment that will be available in the next 2-4 years, 100% BEV adoption is also possible. We recommend a holistic approach when evaluating BEVs for underground mines. This will ensure that everything is considered in order to evaluate the full impact of BEV implementation.

Jan 1, 2023

By James McManus

The original analogue instrumentation at Lornex Mining Corporation to optimize the throughput by controlling the power drawn by the semi-autogenous mills was found to be inadequate because of the frequent changes in ore type. Although the trunnion bearing pressure of the mill was a crucial control criterion, it was not utilized in the original control scheme. After several plant tests of different types of analogue controllers were unsuccessful in finding any control equipment suitable for this application, it was concluded that a digital process control computer was required. Computer control strategy to optimize the grinding rate by controlling the power and the bearing pressure of the semi-autogenous mill was developed and a Fox 2 /30 computer made by Foxboro was selected. After six months of experimentation, it was found that the throughput was increased substantially by computer control.

Jan 1, 1978

By G. Cordingley, A. Mwanza

Lumwana is an open pit Copper mine located in the Northwestern Province of Zambia approximately 80 km west from the provincial capital of Solwezi, approximately 300 km northwest from the Copperbelt and 700 km northwest from the national capital of Lusaka. The mine has two major Copper deposits: Malundwe and Chimiwungo. Copper mineralization includes Chalcopyrite, Bornite and Chalcocite. In addition to Copper, these deposits also contain the undesirable element Uranium contained in vein hosted and disseminated Uranite. The processing plant was designed using conventional technologies: semi-autogenous grinding (SAG) and ball mill for grinding, and mechanical cells for rougher and cleaner flotation. Soon after commissioning in early 2009, it was recognised that two stages of conventional cleaning were unable to produce plant final Copper concentrates with the desired Uranium grades. Studies have shown that a significant quantity of liberated and fine Uranium particles (up to 80-90%) is recovered with the concentrate by entrainment. Lumwana Operations sought the use of the Jameson Cell technology after observing successful implementation at other sites in rectifying similar issues. In late 2009, Jameson Cell pilot-plant test work was conducted at the site and this quickly led to the installation of a full-scale B5400/18 model into the existing cleaner circuit. Inclusion of the Jameson Cell resulted in the plant being able to effectively produce clean and saleable concentrate with Uranium contents consistently below acceptable levels. Initially designed to be used as a cleaner scalper cell at the head of the existing conventional cell circuit, subsequent operational issues with the existing recleaner cells forced reconfiguration of the cleaner circuit and reintroduced the Jameson Cell for the recleaning duty. This paper reports the Lumwana Operation from the first two years of operation where it struggled to produce a saleable concentrate with Uranium grades below 150 ppm, which is the maximum allowable limit set out in the smelting contracts, to steps taken in the subsequent years to implement a satisfactory solution. The plant can now consistently produce a clean Copper concentrate with Uranium grades well below 130 ppm and the overall improvements implemented at site have seen the overall plant recovery improve by 1.3%.

Jan 1, 2014

By Adil Aledresse, N. Emre Altun, Bern Klein, Nuri Hmidi, Brent Hilscher

A study was conducted to investigate high gold grades in water lines and carbon fines collected from the Musselwhite gold recovery circuit. It was discovered that fine magnetic particles in the overflow from the carbon fines settling tank launder had high gold grades ranging from 2,000 to7,000 g/t. The -37 micron fraction had up to 17,000 g/t gold. Scanning electron microscopy revealed the gold was attached to the surface of iron particles. The objective of the study was to identify possible mechanisms that result in the attachment of the gold to the magnetic iron particle surface and to recommend process modifications that would reduce these types of gold losses around the carbon circuits. Solid and solution samples were collected from the gold recovery circuit and analysed. Two possible mechanisms were identified including gold cementation onto iron and heterocoagulation of colloidal gold onto iron oxides in the elution column. Possible sources of the colloidal gold include reduction of gold cyanide complex to metallic gold in the carbon regeneration kiln and gold detached from cathode in EW cell. Based on SEM+EDX, the sources of iron were natural magnetite and roasted iron sulphides. Thermal reduction of gold is believed to be the cause of dendritic gold from the carbon regeneration kiln.

Jan 1, 2014

By Jared Onyirimba, Jim Viellenave, Hal Demuth, Dale Verran, Chad Sorba, Errol Lawrence, David Bronkhorst

As outlined within the Denison Mines Corp’s (“Denison”) Pre-Feasibility Study ("PFS") completed in late 2018, additional work is required to increase confidence and reduce risk associated with the application of the In-Situ Recovery (“ISR”) mining method at the Phoenix deposit, located on the Wheeler River Uranium Project (“Wheeler River” or the “Project”) in northern Saskatchewan. The successful application of ISR in any geological environment largely hinges on three fundamental requirements, 1) permeability (of the deposit), 2) containment (of the mining solution) and 3) leachability (of the mineralization). Denison has designed several staged technical programs to progressively reduce risk associated with these requirements as the Company advances the Project toward a Feasibility Study (“FS”) and Environmental Impact Assessment (“EIA”). This paper will discuss the scope and results of certain technical programs being undertaken as the Company aims to develop the first ISR mining operation in the Athabasca Basin.

Jan 1, 2020

By A. Welty, T. Garn, K. Lyon, B. Jakovljevic, R. S. Herbst, M. Greenhalgh, Cytec Solvay Group

"Industrial rare earth separation processes utilize PC88A, a phosphonic acid ligand, for solvent extraction separations. The separation factors of the individual rare earths, the equipment requirements, and chemical usage for these flowsheets are well characterized. Alternative ligands such as Cyanex® 572 and the associated flowsheets are being investigated at the pilot scale level to determine if significant enhancements to the current separation processes can be realized. These enhancements could be defined as higher separation factors, reduced stage requirements, or reduced chemical consumption. Any of these enhancements can significantly affect the costs associated with these challenging separation proccesses.A mid/heavy rare earth element (REE) separations flowsheet was developed and tested for each ligand in a 30 stage mixer-settler circuit to compare the separation performance of PC88A and Cyanex® 572. The ligand-metal complex strength of Cyanex® 572 provides efficient extraction of REE while significantly reducing the strip acid requirements. Reductions in chemical consumption have a significant impact on process economics for REE separations. Partitioning results summarized Table 1 indicate that Cyanex® 572 offers the same separation performance as PC88A while reducing acid consumption by 30% in the strip section for the mid/heavy REE separation."

Jan 1, 2016

By D. Kovachevich, M. A. Pfeifer

"A t remote locations typical of mines and associated ore processing plants, diesel electric generators are ideally suited for power plants due to their inherent operating flexibility, efficiency and reliability. In recent years rapid escalation in fuel and related transportation costs has made extensive waste heat recovery from generating sets financially attractive to a much greater extent than previously.The paper outlines key considerations during planning and design stages for utilizing the various waste heat sources available to best advantage. Based on two /980 mining projects built in the Canadian Arctic, data is presented on potential operating and capital costs savings. A review of heat balances, engineering flow diagrams and major equipment selections for process and building heating systems utilizing waste heat is included.IntroductionResource projects increasingly occur in remote areas requiring on-site self sufficiency in electrical power generation. For such projects, the low- or medium-speed turbo-charged diesel engine is very often the preferred choice as a prime mover for the generating sets . It is inherently reliable, has good response to load changes and has comparatively high fuel efficiency over a wide load range . From a project execution standpoint, It is capital cost- competitive and procurement lead-time normally ' fits ' within tight schedule constraints. In addition, its potential for waste heat recovery is excellent , particularly in northern climates where space heating requirements are usually substantial, and also where there a re requirements for heat for process and plant services.The high cost of fuel , with add-on transportation costs , provides a major incentive to fully exploit the available waste heat recovery potential o f such installations.As a result of the rapid escalation in the price of petroleum products following major crude oil price increases in 1973 and again in 1978-79, liquid petroleum fuels, having the desirable properties of comparatively high heat content and transportability, are no longer 'cheap' commodities and have become so valuable that industry has widely undertaken serious conservation efforts.Currently, it appears that petroleum cost trends of the 1970s may not continue, at least in the near term, and that we may see somewhat reduced energy costs for a time. In the longer term , and certainly within the life spa n of major projects, however, it is generally believed to be inevitable that these fuels will be increasingly expensive . Energy costs are today a major operating cost for remote minerals processing plants and will remain so for the foreseeable future.In order to meet the economic challenge posed by high energy costs, future projects should be thoughtfully planned from the outset with the goal of minimizing energy requirements and maximizing the use of waste heat recovery to meet such requirements. There is also considerable potential for significant energy savings by retrofitting of existing installations."

Jan 1, 1984

By R. Amata

"The Gakara Rare Earth deposit in Burundi (East Africa) is unique for its high grade (e.g., 54.3% TREO on average) and low uranium and thorium levels. The majority of the light rare earth (RE) elements in material from Gakara are contained within the familiar RE minerals bastnaesite and monazite. Extensive metallurgical test work was conducted by SGS Minerals Services on mineral samples collected from the Gakara deposit. Various whole ore hydrometallurgical processing routes were examined in a scoping level test program. Preliminary beneficiation testing was also conducted, though it was determined that only marginal upgrading would be achieved with significant RE losses. Thus a hydrometallurgical process on whole ore was developed to minimize the overall process complexity and achieve maximum RE recovery. Results from the test work will be presented, along with the selected base case flowsheet involving agitated atmospheric sulphation of the RE minerals, RE double sulphate precipitation, caustic conversion, redissolution, and carbonate precipitation. Following the base case flowsheet, a purified cerium free mixed RE carbonate with low levels of radioactive elements was produced.INTRODUCTIONRainbow Rare Earths Limited (Rainbow) is a mining company engaged in the exploration and development of the Gakara rare earth deposit in Burundi; Figure 1 shows the project location. The project is located in the Bujumbura Province and 45 km from the Burundi capital of Bujumbura. Notable for its exceedingly high in-situ grade – 54.3% on average total rare earth oxide (TREO), low uranium and thorium levels and familiar rare earth minerals, bastnaesite and monazite – Gakara is the world’s richest rare earth deposit. The project, a previously operating mine from 1948–1978, has a significant mineral inventory base, a long life of mine, well understood mineralogy, and robust economics. Rainbow is focused on bringing Gakara into production in the near term, ramping up to produce 5,000 t/y of a 54%+ TREO concentrate."

Jan 1, 2016

By M. Mezbahul-Islam

Thermodynamic modeling of the Mg-Cu-Ni system is carried out as a part of multi component thermodynamic database for Mg alloys. This system is being modeled for the first time using the modified quasichemical model, which considers the presence of short range ordering in the liquid. The thermodynamic descriptions of the binaries Mg-Cu, Cu-Ni and Mg-Ni have been extrapolated to the ternary Mg-Cu-Ni system using Toop geometric model. The constructed database has been used to calculate and predict thermodynamic properties, isothermal sections and liquidus projections of the Mg¬Cu-Ni system, which showed very good consistency with the experimental data.

Jan 1, 2011

By A. J. Rigby

The wear mechanisms of the tuyere lines of Peirce-Smith and Hoboken converters are a subject of endless debate and speculation. However, there has been an indication that one of the primary factors in the deterioration of tuyere lines is due to the batch operation of the converting process. The cooling of the brick in the tuyere line during out-of-stack times leads to shrinkage of the brick and resultant opening of the joints. Subsequently, on re-entry of the tuyere line into the bath, the joints become penetrated with matte and re- expansion of the brick is prevented. It is thought that this regular cycle of exiting the batch for slag skimming and replenishment of matte and re-entering for further blowing leads to a gradual “ratcheting” of the tuyere brick lining. If no expansion allowance is furnished between the endplate and the endwall of the lining, then the generation of damaging compressive stress is unavoidable. INTRODUCTION It is generally accepted industry-wide that the integrity of a refractory lined vessel is determined by an inextricable combination of refractory brick quality, the caliber of the lining design and installation, and the severity of the process inflicted upon the high wear areas of the vessel lining. Rigby has summarized the concentrated attempt, over the past several years, to optimize the microstructural, chemical, and fracture properties of the refractories used in non-ferrous pyrometallurgical vessels. Furthermore, lining design concepts involving larger and longer brick and the extent and positioning of expansion allowance in the joints have been extensively trialed. All these efforts have provided some, but not startling, improvements. The simple fact is that a vessel lining composed of bricks with an optimized microstructure and chemical inertness must installed with a well-conceived design to decompress the lining stresses that are generated by the batch operation of copper converters. REFRACTORY QUALITY Converting is conducted by injecting air into the molten matte and white metal for the very purpose of generating iron and copper oxide slags. These slags must be contained by a refractory which, by its mineralogical formulation, is optimized for chemical inertness.

Jan 1, 2019

By E. C. Payne

"IntroductionTHE SMALLER industrial and commercial steam generating plants in the United States are suffering from an ‘engineering deficiency' which, if allowed to continue, will probably result in the extinction of the species• that now burn •approximately 75 million tons of coal. We will classify as 'small' those plants which should require not more than one operating man per shift, including those in which as little .as thirty minutes per day should be adequate for .all service attention. These are the small steam plants that need the most, and get the least, expert attention for fuel :planning, equipment selection, design layout, .and proper operating technique. Dissatisfaction with bituminous coal is usually caused by one or more preventable weaknesses such as excessive or burdensome labour •for firing, .coal or ash handling and manual operation, smoke and fly ash emission above nuisance levels:, high maintenance and premium coal application for acceptable operation, and .finally, overall steam costs which are not .competitive. These 'deficiencies', so .common in the small coal-fired steam plants, can be readily eliminated by competent engineering and modern equipment with automatic controls."

Jan 1, 1953

By I. Kirman, B. Waters

World wide applications for nickel use will be summarized and examples of those uses given. Nickel products are critical to many important aspects of modern society. These products are just as important for modern China as they are in other parts of the world. It is argued that future pattern of nickel use in China should be expected to be very similar to that in the rest of the developed world. Total use of nickel in products in China is already very large. In 2004, it was the largest market for stainless steel (nickel containing) in the world. A survey of Chinese stainless steel applications will be presented. Current high nickel prices have revived speculation about substitution, particularly for nickel containing stainless steels. The presentation will discuss some of the complicating factors that need to be taken into account when considering substitution. These factors are as valid in modern China as they are in other developed economies. Recent substitution efforts and the reaction to them will be examined. The Nickel Institute position regarding appropriate application of the various grades of stainless steel will be discussed. Price-motivated substitution in China, and elsewhere, will occur but it is argued that the extent will probably be limited.

Jan 1, 2005

By William H. White

"AbstractThe value of anomalous metal contents of trees as an aid to the discovery of mineral deposits was tested under field conditions cm four known ore deposits. Results indicate that a base-metal deposit, or any deposit containing zinc or copper, casts a 'metal shadow' into the overlying soil which remains approximately positioned above the deposit, regardless of the type of overburden or the movement of groundwater.The unusually high content of zinc or copper in trees growing within the limits of this 'metal shadow' constitutes an anomaly which can be detected and ,plotted in the field The field kit and certain points of the field technique are described briefly; and the characteristics of plant anomalies and possible limitations of their use are mentioned.IntroductionRecent investigations concerning the metal content of trees indicate not only wide variations in the metal content of different species and in different parts of the same tree but, in addition, suggest that the metal content of a tree is related to that of the subjacent bed-rock. Abnormal values found by Warren, Delavault, and others in trees growing above or near orebodies suggest a new tool which may prove of considerable value in exploration work. Evaluation of this new tool must involve consideration of the following questions:(I) Is the technique one which can be used under field conditions by persons not specially trained; and can results be duplicated within reasonable limits of error? Rather than taking tree samples for subsequent laboratory analysis, it is highly desirable that analyses be made on the spot. This allows anomalous results to be checked and additional samples may be taken at key points."

Jan 1, 1950

By T. G. Joseph, E. Lampard

ABSTRACT: Surface mining operations must manage variability from within their operations as well as variability imposed upon them by external forces. A framework to manage both internal and external variability through the continuous review and adjustment of a mine plan during active mining lifetime operation is introduced, to minimize lost production and maintain operational safety. The observational approach of “observe, evaluate, interpret, predict, and adapt” is employed as the backbone of this approach. Although written with a surface mining operation in mind, the framework outlined in this paper would be equally applicable to any mining or processing operation.

Jan 1, 2011

By Frédéric Flament, Luc Lachance

"The important task of metallurgical accounting that used to be done manually is being more and more automated. Currently available solutions can generate accounting reports without human intervention or almost. However, the practical conditions for fully delivering the promised benefits of those solutions are sometimes overlooked either by end-users or by integrators. The mere fact of filling reports with values satisfying several constraints such as mass conservation constraints does not, by itself, ensure a high quality metallurgical balance. Since managers make decisions based on these reports, it is logical that the metallurgical balance performance be monitored and retrofits be made if necessary. Such retrofits may involve modifications to the measurement strategy or the reduction of the spatial resolution of the material balance model. This requires an estimability and redundancy analysis (ERA) tool to assess the feasibility of the modified model. Since determining by hand the estimability and redundancy of a set of non measured and measured variables is not trivial, even for a medium-sized mineral processing plant, a dedicated ERA tool brings valuable assistance to the metallurgist in charge. The present paper aims first at explaining how a state of the art metallurgical balance is a key enabler for the adoption of a smart process plants paradigm (SPPP) in mineral processing. Then, the fundamentals behind the building of an ERA algorithm are introduced and illustrated by two examples. Finally, the role of an ERA tool in achieving state of the art metallurgical accounting and how it contributes to delivering additional value are discussed.INTRODUCTIONThe Smart Process Plants Paradigm (SPPP)Mineral processors have seen an increase lately in external pressures toward operating performance improvements. Indeed, the globalization of the mining business is a key driver to becoming more productive, more responsive to market changes, to improving corporate governance and reporting standards. Furthermore, mineral processors are also expected by their neighbouring communities to continuously improve their sustainability score. These current pressures differ somewhat from the past ones in leading to a larger than ever number of conflicting constraints that plant managers must concurrently satisfy while maximizing plant profitability. It is in turn not surprising that this context requires actions involving more real-time collaborative actions between more people in more places than ever before."

Jan 1, 2011