Search Documents

By H. Zhu, Q. Jiang

The leaching kinetics of iron during the atmospheric direct leaching (ADL) of marmatite concentrate was studied under the following conditions: reaction temperature of 343-383 K, slurry pressure of 0.3-0.7 MPa, particle size of (-74 ?m, +63 ?m), (-63 ?m, +44 ?m), (100%-44 ?m). The statistical effects of reaction temperature, total pressure and particle size of concentrate on the extraction and the leaching rate of iron were analyzed. The results show that reaction temperature is a significant factor while slurry pressure and particle size are not statistically meaningful with respect to the extraction or the leaching rate. The extraction of iron fits better to the mixed-controlled shrinking core model and the apparent activation energy was calculated to be 37.66 kJ/mol. The leaching of iron is mixed controlled by the interfacial chemical reaction and diffusion across the product layer.

Jan 1, 2014

By Bernard Tougas, Franco Chiesa, David Levasseur, Bernard Duchesne

"In the present paper, the optimization of a tilt poured permanent mold will be carried out using filling and solidification modeling. This exercise resulted in 3 modifications of the initial mold design which was based on the foundry experience. The optimization provided a 20% improvement in the yield while increasing the output from 10 to 15 castings per hour.In a subsequent study, the value of the critical fraction solid of AlSi7Mg (A356) alloy was verified by radiographic analysis of the castings produced in the first 5 cycles of a run, which are necessary to bring the mold to a dynamic thermal equilibrium."

Jan 1, 2014

By Tapiwa Chenje, Victor Olivas, Peter Radziszewski

"Ore breakage and grinding media wear have always been considered and determined separately in laboratory tests. However the two processes are linked with the ore broken down in any comminution device being responsible for the majority of the steel wear experienced. The Comminution Dynamics Laboratory (CDLab) successfully developed a test methodology that can more accurately predict grinding media wear in tumbling mills than the Bond Abrasion test. This paper looks at the possible application of the abrasive wear methodology to determine breakage parameters of the same ore used in the abrasion test. Results indicate that breakage parameters comparable to t10 can be determined using the Steel Wheel Abrasion Test (SWAT), while using significantly less ore than standard breakage tests.BACKGROUNDThe Rubber Wheel Abrasion Test (RWAT) is an internationally accepted and widely used method for determining the abrasion wear behavior of materials. The abrasion wheel test was developed to primarily utilize a steel wheel (Brinell, 1921). Haworth (1949) criticized using of the steel wheel by arguing that increasing the contact area size in the steel wheel test causes a change in the wear rate with time. He suggested that the use of a rubber wheel instead eliminates this problem, leading to the adoption of the RWAT which was standardized in ASTM G65 (2004).Radziszewski (2002), however, found that the use of the Steel Wheel Abrasion Test (SWAT) was more applicable for wear testing in the mining industry for two critical reasons. Firstly, the major cause of wear in a ball mill, the most frequently used comminution device, is ball-ore-ball contact and also ball-ore-liner which both are metal-ore-metal contact. Therefore, using the steel wheel has the advantage of providing a similar abrasive environment to the one that takes place in a real ball mill. Secondly, the SWAT creates the potential of running experiments at much higher force regimes that are closer to what happens in actual mills, unlike the RWAT which is a low stress test."

Jan 1, 2011

By W. K. Gummer

"THE LOCATION of Canada's present aluminum industry is determined by availability of hydroelectric power, and ready access to ocean transport facilities. The chief raw material for the production of the metal is imported by ship over several thousand miles of water. In times of freedom of shipping and uncontested movement this provides the industry with its cheapest method of operation. However, during the early part of the last decade the general conditions of ocean and rail transportation were such that interest in the treatment of materials other than bauxite was greatly stimulated. This was the case not only in Canada, of course, but in most other countries.Canada has no deposits of bauxite and much research was carried out on other aluminous materials, chiefly silicates, in an effort to develop more or less economic and feasible methods of treatment. In the United States, this research was considerably more extensive. Some projects were early shown to be of little or no value, whereas others, including the widely publicized lime-sinter and soda-lime-sinter methods, became important. In North America, however, apart from the application of the sinter method to the hitherto waste-product (red mud) of the normal Bayer plant operation, none of these processes contributed appreciably to the production of aluminum during the war. In certain European countries, on the other hand, largely because of their situation with regard to bauxite deposits, they had a more general application, and Germany, for example, produced alumina from clay, ashes, and slag by at least four methods."

Jan 1, 1952

By R. A. Hemstock

"OIL EXPLORATION in Western Canada has produced outstanding results in the past few years. From such successes as Leduc and Redwater on the western plains, oilmen are now moving north in the ever-widening search for oil. They are reaching new frontiers and meeting new problems presented by this vast hinterland.One of the least known but most troublesome phenomena which will be encountered is permafrost. This term relates to a thickness of soil or other superficial deposit, or even of bed-rock at variable depths beneath the surface, in which a temperature below freezing has continually existed .for a long time. This permanently frozen ground affects, in many ways, oil exploration and exploitation. Seismic records are changed, pipe lines cannot easily be ditched into the ground, formation of wax is speeded-up in tubing and pipe lines, roads are difficult to build, and foundations of buildings and even of drilling 'rigs may require entirely new methods of construction.Permafrost underlies roughly one-fifth of the entire 'land surface of the world. It covers the northerly portions of Eurasia and North America. In the area that we are here concerned with, the southern boundary of permafrost extends south of east from about latitude 59°N. on the Pacific coast across the Rocky mountains, through Great Slave and Athabasca lakes, to cape Henrietta Maria, at the junction of Hudson bay and James bay (see Figure 1). Geologists generally agree that permafrost first appeared in the Pleistocene or Ice Age as the result of abnormal ground freezing."

Jan 1, 1952

By J. M. Rios

Without conscious effort and understanding, a number of factors peculiar to mineral exploration campaigns conspire against building sustainability in host communities. These include the episodic and transitory presence of an exploration team in the community and the inherent uncertainty of outcomes; most projects fail. Given these circumstances, there is a strong tendency to apply a simple formula of providing employment, pragmatic philanthropy and supporting infrastructure improvements (roads, schools and clinics) to demonstrate that mining provides benefits. Experience in rural native communities of Mesoamerica has shown that it is possible to create positive, sustainable outcomes quite rapidly within communities, which build capacity, improve quality of life and support a strong social license to operate. Success comes from an understanding of community structure and dynamics; engaging with all segments of the community; creating healthy, transparent and accountable relationships based on clearly defined roles and responsibilities; and supporting and strengthening the role of women in a culturally appropriate way. To this are added innovative and culturally appropriate ways of incorporating sustainability through genuine social investment in areas more typically addressed by exploration companies; health, education, and environmental management.

Aug 1, 2013

By S. A. Jacob

Magnesium sheet is notoriously difficult to form at low temperatures without initiating failure, In the present work cold rolling and annealing conditions are varied to produce samples of AZ3lB sheet with a range of grain sizes. The formability of these samples is investigated using tensile testing and forming limit diagrams (FLD's), The results are discussed in terms of twin types and frequencies.

Jan 1, 2005

By Rodolfo Espinosa

"Industrias Peñoles, S.A. de C.V. in Mexico, has nine mining operations, six managed by Peñoles (base metal mines) and three managed by Fresnillo plc (precious metal mines). Seven of the operations use flotation and the other two are heap leach operations, one for gold and the other one for copper.This paper gives a brief introduction of Peñoles, shows mine locations and describes the main process characteristics of each concentrator. It also presents four of the new operating practices that were implemented over the last four years to improve the economics of the mining operations. These include (1) the use of centrifugal gravity concentrators to increase the recovery of gravity recoverable gold (GRG) and silver (GRS), (2) the use of expert systems to reduce process variability while increasing grades and recoveries, (3) the application of the Six Sigma methodology to key projects to ensure success and personnel development and (4) the use of water chemistry fundamentals to identify chemistry problems and design adequate solutions for improving grades and recoveries.INTRODUCTIONPeñoles was founded in 1887. It is a mining group with integrated smelting, refining and chemicals producing operations. Peñoles is the world largest producer of refined silver and metallic bismuth, the leading Latin American producer of refined gold and lead. It is amongst the world leading producers of refined zinc and sodium sulfate.Peñoles operates and controls six underground mines in Mexico and is the largest producer of zinc and lead of the country. It also produces copper concentrates and cathodes. Through its 77.1% equity stake in Fresnillo plc (a London Stock Exchange listed company); Peñoles is also a significant producer of gold and silver. Fresnillo plc operates three precious metal mines in Mexico. While Fresnillo is the world largest primary silver mine, Ciénega and Herradura are two leading gold mines of Mexico. Figure 1 shows a map of Mexico indicating the locations of the Peñoles mines. The main process characteristics of each concentrator are listed in Table 1."

Jan 1, 2011

By Jerry Ran

Many large underground mines using the open stoping method have changed their primary applications of consolidated rock fill (CRF) to paste or consolidated hydraulic fill due to considerations of demand in infrastructure and equipment, system reliability, backfill capacity and material sources. However, some smaller or even large mines still use or consider using CRF for backfill purpose due to factors such as capital expenditure, availability or suitability of other fill types or in some cases local regulatory requirements. As demands on CRF applications diminish among major mining companies, there is a lack of recent literature on application of CRF to open stoping in design and operation. There are several methods being used for fill strength design. Results from these methods have been successfully applied to paste or hydraulic fill. However, the design strength for CRF is much higher than that determined by use of these widely accepted methods. In operation, CRF preparation and placement have significant impacts on the quality of placed CRF and therefore the mining performance. This paper reviews the current fill design methods and their applications to open stoping with presentation of the bench marking data, presents fill failure cases and various CRF preparation and placement arrangements and discusses quality assurance and control programs.

Jun 1, 2012

By Gobbs C., J. Lam

"The Eagle East project, accessed from the existing and operating Eagle Mine in the Upper Peninsula of Michigan, is an underground base metal project currently in execution by Lundin. This paper will provide an update on several aspects of ventilation including use of a twin-decline access, innovative airflow crossover arrangement and construction ventilation methodology. Integration into existing mine ventilation systems including construction methodology will also be covered. Performance benchmarks and lessons learned are discussed across these topics.INTRODUCTIONLundin has owned and operated the Eagle Mine since 2013. This hard rock underground mine is located in the upper peninsula of Michigan, USA. High-grade nickel ore is mined using sublevel open stoping mining methods and trucked to surface via haul ramp. The mine, having been in production for four years, is nearing the completion of the initial orebody. A satellite orebody 2,000 meters East of the current workings and approximately 900 meters below surface, was identified that could extend operations until 2023. In 2016, Lundin approved the Eagle East project and construction began in 2017 (Lundin Mining Corporation, 2017).Due to proximity to the existing mine, Eagle East will be both accessed and serviced from the existing Eagle Mine. Ventilation at the Eagle Mine uses two fresh air intakes with direct fired combustion heaters; one at the mine portal feeding fresh air into the ramp and one at a fresh air raise located near the Eagle deposit. The primary ventilation circuit is powered on the exhaust air side, with two 700 hp exhaust fans located at a single return air raise. Underground, fresh air is distributed through the main access decline and fresh air raise (FAR) to the production levels and controlled with mechanical regulators on the exhaust side. The exhaust air is collected through return air raises with a collector/transfer drift on 250 Level and then to the surface through a return air raise (RAR)."

Jan 1, 2019

By E. O. T. Simpson

"IntroductionAS COMPARED with coal mines in the United States, and even with some of those in eastern Canada, the coal mines of western Canada, generally speaking, :have made little progress toward mechanization at the working faces. So far as Vancouver island is concerned, there are three main reasons for this : ( 1 ) in some areas, conditions• easy for hand-loading but unsuitable for mechanical loading make high outputs per man •possible by the former method; (2) faulting of the coal seams in ..some areas precludes long-term planning and the introduction and efficient use of expensive equipment; (3) thinness •and other characteristics of the seams in many areas favour hand-loading.No. 8 MINENo. 8 mine of Canadian Collieries (Dunsmuir), Limited, is located in the Cumberland sub-area of the Comox coalfield on Vancouver island about 90 miles west-northwest of Vancouver. The geological structure of this coalfield has been described by J. D. McKenzie. The seams occur in the Comox formation, a subdivision of the Upper Cretaceous Nanaimo Group. The formation is of near-shore origin and was laid down on an irregular surface of' older rocks. The irregular generally have a northeasterly dip, modified by gentile folds and by a •few large, and a number of smaller, faults.Four seams have been worked in the Cumberland area and all vary in thickness and in the amount and number of interstratified bone and rock •bands."

Jan 1, 1953

By D. L. Johnston

"Function and ApplicationsWater-only cyclones, (WOC) are a dynamic mineral separator which cause minerals to separate in a water medium by virtue of difference in specific gravity. Figure 1 shows diagramatic plan and sectional views of a water-only cyclone.A slurry of mineral matter and water is fed through the inlet opening under gravitational or pump pressure. The combined effect of centrifugal action and conical shape is to concentrate the heaviest fraction of mineral on the periphery and bottom of the cyclone. This layer of higher specific gravity particles increases in thickness and density between the cyclone inlet and apex. The action in the bed of higher gravity particles formed in the flattened portion of the cone surrounding the tip of the vortex finder deter;nines the specific gravity of separation or cut-point. Mineral particles of lower specific gravity flow with the bulk of the water, out the vortex finder. Mineral particles of higher specific gravity flow with little water out the apex. A more technically e:mct description of the functioning of the water-only cyclone can be found in previous publications noted in the references.The water-only cyclone was invented and refined by J. Vis man, formerly of the Canadian Mines Branch staff, between 1958 and 1965. The first industrial application noted in the literature was when it was introduced as a cleaner for fine coal in 1962. Since 1970 the water-only cyclone has become a common separation apparatus in many Canadian and foreign coal processing plants. The only other mineral industry application known to the author is in separation of gold bearing heavy minerals from sand<'>. The potential does exist for other applications and this area deserves to be investigated more thoroughly than it has been."

Jan 1, 1989

By J. B. Kwon

For improvement in the productivity of tall building projects, table formwork is one of the main methods that have been adopted for slab formwork. Because the table formwork method is an equipment-oriented construction method, the type of lifting equipment and method of operation considerably affects the productivity and cost of the table formwork. It is also important to make an equipment input plan for completing the table formwork within the time given, according to the structural construction cycle. For performing the table formwork, a tower crane or an independent lifting system, and shifting trolleys, are required. However, if an inefficient equipment input plan is made, exorbitant cost may be incurred. Therefore, the purpose of this study is to analyze the productivity of a table formwork, considering the type and number of lifting equipment and the number of trolleys inputted, and to suggest quantitative data for making a cost-efficient equipment input plan within the construction duration given. It is expected that the results of this research will be utilized as a basis for cost-efficient equipment input planning.

Aug 1, 2013

By L. Chunpongtong

ABSTRACT Oil sands production occurs on a massive scale, making orebody estimation a challenge. In rainy conditions, operators can have difficulty accessing ore at the mapped location. Without enough inventory as a buffer, the high-cost stockpile is depleted quickly, necessitating the removal of significant amounts of overburden and interburden to meet plant feed requirements. The inventory curve—a plot of ore inventory on a period-by-period basis—plays an important role in selecting an appropriate scheduling scenario. This paper presents a programmable method for creating an inventory definition by using a pit optimization tool.

Jan 1, 2014

The Mineral Industry of Canada in 1951 Continuance of the remarkable, successive increases in the value -of Canada&apos;s mineral production, chief basis of the nation&apos;s post-war expansion, was one of the highlights of Canadian development in 1951, when, according to the preliminary estimate is-sued by the Dominion Bureau of Statistics and reported in the BULLETIN for February, 1952, mineral output for the year reached a new high of $1,228 millions. This marked an increase of 17.5 percent over the previous year, which was the first in which the billion dollar mark had been reached, and an increase of 143.7 per cent over 1946, when production was valued at approximately $503 millions. While higher prices for the principal base metals accounted for a large part of the 1951 increase, quantity gains were made by copper, nickel, zinc, asbestos. lead, cement, and strikingly important. by petroleum, the value of which exceeded for the first time that of coal production. Gold was an exception to the general trend, being lower in both quantity and value than in 1950. For the first time nickel .came within $9 millions of surpassing-gold as the leading mineral product. Metals and Fuels The value of all metals, estimated at $733 millions, was 18.7 per cent more than in the previous year. Nickel advanced 11 per cent in volume and 34 per cent in value. Copper was up 2.4 per cent in quantity and 21 per cent in value, zinc rose 6.6 per cent in quantity and 35 per cent in value, and although the volume of lead produced was lower by 8 per cent, its value increased by 17 per cent. The tonnage of iron ore was 31 per cent higher than in 1950.

Jan 1, 1952

By James B. Templeton

"IntroductionWith the steady rise of the cost of coal and freight, the time is now ripe for an investigation into the feasibility of using the heat pump for heating purposes in fairly remote industrial areas.The gold mines of northern Ontario seemed to be a most likely place for the application of the heat pump.It was decided that the first step in the investigation would be to determine what economic advantage was to be gained by using the heat pump and thereby determining whether a further and more detailed research programme was warranted.If we can use the heat pump with economic advantage, we can reduce our mining costs and make a worthwhile contribution to our national economy by reducing the import of U. S. coal.The investigation was conducted under the auspices of the Nipissing Fellowship and directed by Professor R. E. Barrett of the Department of Mining Engineering, University of Toronto.With the able guidance of Mr. C. S. Gibson, of the Mines Accident Prevention Association of Ontario, the author visited the following mines: Mcintyre-Porcupine, Delnite, Dome, Lake Shore, Wright-Hargreaves, Kirkland Lake, Macassa, and Kerr Adcliso11.In all cases, the management and technical personnel of these mines were most co-operative and helpful in supplying information and ideas.It should be emphasized at the outset that the design and operation of the heat pump itself is by no means complicated or even new. The reason we hear so much about it today is because there have been improvements in compressors, motors, and heat exchangers in the past few years, and because fuel and freight rates have risen to such a point that, in some cases, the heat pump now has an economic advantage over other methods of heating."

Jan 1, 1950

By C. Mawdsley

The Tata Steel mill at Skinningrove in the North East of England produces top hat sections for mineshaft guides in sizes 102 and 150 mm. The top hat section is the technically preferred shaft guide choice for modern deep mine shafts. This paper explores the relative service performance of top hat and square hollow section guides in service. Comparative corrosion performance is reviewed and the paper describes work commissioned by Tata Steel (as Corus) undertaken by Aker Kvaerner Engineering to evaluate relative winding speeds, relative loads and fatigue life in service. The experience of supply to UK Potash mining is discussed and the future view of high capacity hoisting and larger section size market need and availability is assessed.

Aug 1, 2013

By D. Hodouin

Jan 1, 1978

By Zhiyang Long, Ruiling Xiao

"A mine shaft is one main development method of establishing access in an underground mine. The construction technology of the mine shaft sinking is complicated and large equipment setup on surface and in the mine shaft. The paper briefly reviews a single-line operation method, parallel operation method and mixed operation method as well as the features of the one operation method with the excavation, lining and installation. The special construction technology mainly would include ground freezing methods, full diameter shaft drilling methods, caisson methods, grouting technology and concrete curtain methods as well as other methods. The paper summarizes the shaft sinking numbers and effects by the special construction methods during different periods. The paper states the shaft sinking conditions and the each created record conditions in the coal, metallurgy, non-ferrous metal, hydropower, highway, railway, nonmetallic and other industries. The paper has a prediction on the shaft sinking requirements and development tendency in the future for China.INTRODUCTIONA mine shaft is one main development method of access in an underground mine. In recent years in China the new shaft mines represent 45% of the total number of new mines. With the development of new mining area under construction and the development of deeper mines, the ratio of the mine shaft as access for underground mines will increase. The construction technology of the mine shaft engineering will be complicated, the operation site footprint will be small and the working environment will be more difficult. The mine shaft sinking operation will often be varied by the geological conditions and affected by underground water inflows, seam gas outbursts, geothermal and other natural conditions. The safe construction of the mine shaft sinking will be challenged by all these conditions. Although the mine shaft engineering will only be about 5% of the total mine roadway engineering, the mine shaft construction period often will take over 40% of the total mine construction period. With the progress of modernized mine production technology and the construction of a high production and high efficient mine, the mine transportation roadways mostly would be set in the seam and the engineered amount of the mine rock roadways reduced year by year could cause more prominent long extensions of the mine shaft construction period. Therefore, in order to speed up the construction, to shorten the mine construction period and to realize the investment benefits as early as possible, the technical level of the mine shaft sinking should firstly be improved and the construction speed of the mine shaft engineering and sinking should be speeded up, which would have important significant benefits."

Jan 1, 2019

Several inorganic reagents and organic polymers were tested as depressants in the single mineral flotation of ultrafine iron oxide and hydroxylapatite with Dowfroth 250 as a frother. It was observed that the inorganic reagents and the low molecular weight polymers generally caused dispersion of the ultrafine particles, and consequently their recovery into froth products more or less equaled the recovery of water. On the other hand, the high molecular weight polymers caused different degrees of flocculation of the ultrafine particles, and their recoveries were much lower than the recovery of water. These observations pointed to a need to re-define flotation depressants in fine particle flotation. The traditional definition of a flotation depressant, i.e., to make particle surfaces hydrophilic by forming a hydrophilic film and/or by removing collector and activator coatings, is sufficient for relatively coarse particles. However, to prevent fine and ultrafine particles from floating, a successful depressant should not only make the particles hydrophilic, but also enlarge the particle sizes so that they do not enter the froth product by mechanical entrainment. Polymeric depressants are ideal for these purposes. The different schemes to use polymeric depressants in the selective flotation of fine and ultrafine particles were discussed These schemes involve the integration of the polymeric depressants into other size enlargement processes such as shear flocculation, oil agglomeration, etc., for hydrophobic particles.

Jan 1, 2004