Search Documents

By V. L. Eardley-Wilmot

Introduction We are all familiar with the bright and attractive colours of the roofs of our suburban houses and country cottages, but few of us fully appreciate the complex and highly technical nature of the business which produces these roofings. Roofing granules consist of small broken particles of certain types of rocks, burned clay products, or slag. They are used either in their natural state or artificially coloured and are affixed onto one surface of asphalt sheeting. Their main functions are to protect the roof against external fire hazard, prolong its life, and enable it to withstand extremes of weather over a period of years without deteriorating. Pleasing designs and colours are added attractions. The reverse, or inner side, of the sheeting is coated with a film of talc or fine mica to prevent it sticking when rolled up for convenience of handling for transport. The finished sheets or strips are cut into a variety of shapes for roofing shingles, or for sidings which resemble rows of bricks separated by mortar. In Canada, the consumption of roofing granules has increased fourfold in the past decade and indications are that the industry will continue to expand. At present, fourteen plants are engaged in manufacturing granule-coated roofings, but, apart from a relatively small output of natural granules by two producers in British Columbia, only one eastern producer makes both natural and coloured granules in Canada, and these only for its own use. The annual consumption is now over 77,000 tons of roofing granules valued at more than $1,600,000, but about 62 per cent of the tonnage is imported. It is thus apparent that the production of Canadian-made granules, both natural and coloured, could be considerably increased. This paper is presented in order to give an outline of the industry and at the same time to point out its difficulties and pitfalls.

Jan 1, 1946

By N. Saracoglu, J. P. Golightly, R. H. Wallis, J. J. Brummer

"The McClean uranium deposits are located 11 km west northwest of the Rabbit Lake Mine. Their average grade is 1.8 % U3O8 , and they contain 6. 350 tonnes of uranium oxide in seven pods of variable grade and mineral assemblage. They are hosted by both basal Athabasca Group and the regolith developed on the underlying crystalline basement. The major mineral facies are: sulphide, arsenide, 'bleached', and hematite, with the important uranium minerals being coffinite, uraninite and pitchblende. Abundances of carbon and sulphur isotopes are consistent with their derivation from pyritic graphite in basement gneisses. Isotopes of oxygen and hydrogen suggest equilibration at temperatures of about 200°C. Ar39/ Ar40 age determination of illite associated with ore suggest mineralization began about 1300 m.y. ago and that significant alteration had ceased by about 1170 m.y. ago though Pb/ U data suggest the deposits continued to evolve into the Mesozoic.IntroductionThe McClean deposits lie on the eastern side of the Athabasca Basin of northern Saskatchewan where they are part of a cluster of uranium deposits lying west of Wollaston Lake (Fig. 1). The general stratigraphy is schematically portrayed in Figure 2 which emphasizes that mineralization is hosted by both the Athabasca Group and the underlying regolith and also that the deposits are preserved at depth and have not suffered from preand post-Pleistocene weathering and erosion. This circumstance, combined with their simple shape and the presence of seven separate zones of mineralization (pods) allows a description, based on over 450 fully cored drill holes, to be made of the wide variation in chemistry, grade, alteration patterns and position relative to the sub-Athabasca Group unconformity. Ar39 / Ar40 age determinations have been made of illites associated with regolith, Athabasca Group and mineralization and studies are in progress on C, S, 0 and H isotopes of mineralized material and host rocks. Only some of these data have been published; Brummer et al., (1981); Golightly et al., (1982); Bray et al., (1982); and Saracoglu et al., (1983). The only other published data on McClean geology are by Tremblay (1982, 1983)."

Jan 1, 1986

By Yuanming Pan, Brett Rogers, Baoquan Hu, Gary Yeo, Christine Austman

The nature and distribution of radiation-induced defects (RIDs) in quartz from the Maw Zone, a yttrium- and rare-earth-element-enriched sandstone breccia complex exhibiting intense hydrothermal alteration, have been investigated by electron paramagnetic resonance (EPR) spectroscopy. EPR spectra show that detrital quartz in sandstone, from five diamond drill holes intersecting the Maw Zone and one above the crest of the so-called Quartzite Ridge, contain only background-level RIDs, indicating that Ubearing fluids were absent in this area. However, close to the sandstone-basement unconformity, in hole WR-194 immediately west of the Quartzite Ridge, the concentration of RIDs in detrital quartz is significantly above background but at least an order of magnitude lower than those at the Key Lake and McArthur River deposits. Widespread drusy quartz at the Maw Zone, which signifies intense hydrothermal alteration, is associated with hematite-, sulfide- and carbonate-bearing mineral assemblages, which exhibit complex crosscutting relationships. EPR spectra of drusy quartz in all three types of mineral assemblages are low in RIDs as well, supporting the EPR evidence that fluids at the Maw Zone did not carry significant U. These EPR results suggest that, in spite of intense hydrothermal alteration and favorable structural geology, the Maw Zone is unlikely to host any significant U mineralization. Moreover, this study shows that the EPR technique is potentially a useful exploration tool, capable of determining whether individual alteration zones in the Athabasca Basin were associated with U-bearing fluids or not.

Jan 1, 2013

By P. Au, P. Patnaik, H. Saari, D. Y. Seo, S. Bulmer

Ti-48Al-2Cr-2Nb-xW (where x = 0, 0.5, and 1 at. %) powders were consolidated by hot isostatic pressing (HIP). The consolidated samples were solution heat treated above the a-transus followed by stepped cooling to room temperature. Selected samples were subsequently aged at 950 °C for up to 72 hours. The post-heat treatment microstructure was examined by optical and electron microscopy. It was found that increasing holding time above the a-transus generated a more homogenous microstructure. Utilizing the stepped cooling sequence, especially with a transition temperature of 1270 °C, massively transformed gamma (Ym) was diminished. Aging caused coarsening of the fully lamellar microstructure in the 0%W and 0.5%W samples while almost no coarsening occurred in the 1 % W sample. Precipitates began to form during aging in samples containing W. The precipitates at the lamellar interfaces are fine and have a needle like shape, while precipitates at the lamellar grain boundaries are coarse and circular in shape. The size and number of the precipitates depend on aging time and the level ofW content.

Jan 1, 2006

By Will S. Pettitt

Fracture Network Engineering (FNE) is the engineering design of rock mass disturbance through the use of advanced techniques to model fractured rock masses numerically, and then correlate field observations with simulated fractures generated within the models. Microseismic (MS) monitoring is a standard tool for evaluating the geometry and evolution of the fracture network induced during a hydraulic treatment, principally by source locating MS hypocenters and visualizing these with respect to the treatment volume and infrastructure (Figure 1). The integrated use of Synthetic Rock Mass (SRM) modeling of the hydrofracturing with Enhanced Microseismic Analysis (EMA) provides a feedback loop in which the SRM is constrained by the information provided by the MS data and the in-situ behavior of the fracture network is better understood, leading to informed decisions on future field operations. This paper discusses the technologies used in FNE and some of the developmental challenges we face in order to provide a more efficient and robust application of the approach. One particular challenge is the accurate representation of MS source data within the models (locations, magnitudes and mechanisms), and the ability to correlate these data effectively with field results. This challenge is being overcome by the development of more efficient numerical modeling algorithms, providing simulations in three dimensions at reservoir scale, combined with validation of these algorithms using laboratory and field case studies.

Jun 1, 2012

By Guoqiang Lan, Jun Song, Bin Ouyang

Rare-earth pyrochlores, commonly exhibiting anomalously low lattice thermal conductivities, are considered as promising topcoat materials for thermal barrier coatings. However the structural origin underlying their low thermal conductivities remain unclear. In the present study, we investigated the phonon properties of a group of RE pyrochlores, Ln2Zr2O7 (Ln = La, Nd, Sm, Gd) employing density functional theory and quasi harmonic approximation. Through the relaxation time approximation (RTA) with Debye model, the thermal conductivities of those RE pyrochlores were predicted, showing good agreement with experimental measurements. The low thermal conductivities of RE pyrochlores were shown to largely come from the interference between the low-lying optical branches and acoustic branches. The structural origin underlying the low-lying optical branches was then clarified.

Jan 1, 2015

By B. E. Halbert, K. T. Himbeault, S. L. Fernandes, R. L. J. Phillips, B. J. Topp

The Beaverlodge uranium mining and milling facilities operated from 1952 to 1981 with about 94% of the ore extracted from the main underground mine and 6% from smaller satellite deposits. Decommissioning work occurred from 1982 to 1985 involving periods of shutdown, salvage and reclamation. Transition phase monitoring, leading to eventual delicencing commenced in July 1985. Over the last 15 years, discharge from the tailings management facility (TMF) and a fresh water stream, impacted during the operational phase by tailings spills, has improved in water quality for most parameters of concern. Loadings to the environment of three key contaminants (radium-226, total dissolved solids, and uranium) have consistently been less than during the operational phase with radium-226 having the greatest variability. Outstanding environmental issues associated with the recovering drainage system formerly used for tailings disposal, are being addressed in an enhanced environmental monitoring program to commence in 2000. Changes in water chemistry and the natural re-introduction of aquatic organisms are issues of concern. In the meantime, application for release from selected satellite areas commenced in 1999. This paper reviews the issues which have arisen during the transition phase, outlines how they have and are being addressed, and provides a comparison of original and current predictions of the recovery process under way at the former Beaverlodge mine site.

Jan 1, 2000

By D. J. Robertson

"THE copper smelting operation of the Hudson Bay Mining and Smelting Company, Limited, at Flin Flon, Manitoba, generates a gas flow of 350,000 c.f.m. at n.t.p. This gas stream passes to atmosphere through a 20-foot diameter by 250-foot brick stack, carrying with it an appreciable dust burden in the form of metallic oxide fumes. The flow constituents during the period 1952 and 1953 and •before gas filtration was included in the treatment scheme are shown in Table I. This paper describes the gas filtration treatment which was installed in 1957, using glass cloth media to recover this dust burden, and discusses the associated problem as its treatment for recovery of zinc and cadmium.The metallurgical details associated with the problem are illustrated by a description of the material flow sequence of the Company's hydrometallurgical zinc plant and copper smelter. In this ore processing complex, the zinc plant and copper smelter form an integrated unit within which intermediate zincrich products of each operation enter the treatment circuit of the other."

Jan 1, 1960

By Samuel Frimpong

Green house gases have become a major concern within the international community over the last two decades due to their potential link to global warming. Carbon dioxide (CO2) is the principal greenhouse gas. In the Kyoto Agreement, Canada has committed to reduce emissions by 6 % below 1990 levels by 2012. This presents a serious economic challenge to Canada and Alberta. Over the next decade, oil sands production expansion, population and industry growth and energy demand will increase CO2 emissions. Current and future CO2 emissions and their economic implications in Alberta will be critical in formulating a comprehensive and balanced policy for dealing with concerns in this area. Disposal of carbon dioxide (CO2) in land aquifers is a potentially viable option for Alberta in dealing with long-term CO2 emissions. Studies have confirmed the existence of appropriate aquifers in the Alberta Basin for CO2 storage over a long geological period. Carbon dioxide is an ideal candidate for aquifer disposal because of its high density and solubility in water at relatively high pressures. In this study, the authors develop a computer simulation model of a scaled aquifer disposal system. The scaled model consists of an injector well, aquifer environment with dominant Ca++ and Mg++ cations. Liquefied CO2 is injected at an appropriate pressure and concentration through an injector well model. The injected CO2 migrates from the point of contact between the injector well and the aquifer domain to the main regime of the latter. The rate of migration is a function of porosity, permeability, cations, aquifer fluid flow regime and CO2 injected pressure. These models are validated using flue gas data from the 546 MW Wabamum Power Plant in Alberta. The total energy requirements for aquifer CO2 disposal system are distributed between a minimum of 105 MW and a maximum of 172 MW, with a mean of 132 MW and a coefficient of variation of 10%. The results show that there is significant variability in all the energy requirements for the CO2 disposal system. The total energy requirements for the disposal system as a fraction of the total power generated by the Wabamum plant of 546 MW could be between 0.19 and 0.32. This is a very significant energy requirement and thorough analysis must be carried out to reduce this variability and energy requirements.

May 1, 2001

By L. A. Jameson, J. Awmack, P. J. Lind

"Peñasquito is a polymetallic deposit containing gold, silver, lead, and zinc. The operation is currently the largest producer of gold in Mexico. Over the next few years, the process flowsheet will be expanded beyond the flotation of lead and zinc to include flotation of pyrite from zinc tails and subsequent leaching of the pyrite concentrate. This paper outlines mineralogical leach characterization that has been carried out to improve the understanding of the complex hosting of gold and silver minerals in the ore. Organic carbon that is present in the ore can have an impact on flotation and leaching. Mineralogical techniques used to characterize this deleterious component of the ore are introduced.INTRODUCTION Goldcorp’s Peñasquito operation is located in the Mexican state of Zacatecas, approximately 200 km from the city of Zacatecas as shown in Figure 1. Peñasquito has been in operation since 2009 and is currently Mexico’s largest gold mine. Mining is carried out by open-pit methods, with oxide ore proceeding to a heap leach facility and sulfide ore treated in the sulfide processing plant.The processing capacity of the sulfide plant is 130,000 tonnes of ore per day and in 2016 production amounted to 450,000 ounces of gold, 17.6 million ounces of silver, 109 million lb of contained lead, and 263 million lb of contained zinc in lead and zinc concentrates. GEOLOGY The Peñasquito deposit is hosted in and adjacent to two breccia pipes; Peñasco and Breccia Azul. The two breccia pipes are branches of a larger intrusive-related complex, which is hosted in the sedimentary Caracol formation as illustrated in Figure 2. The regional geology is dominated by Mesozoic sedimentary rocks which comprise a thick series of marine sediments deposited during the Jurassic and Cretaceous periods. A 2 km thick sequence of carbonaceous and calcareous siltstones and interbedded sandstones is underlain by a 1.5 to 2 km thick limestone sequence (Goldcorp Inc., 2015)."

Jan 1, 2017

By F. Tanaka

Copper losses to discard slag have long impacted on the profitability of copper smelters. Businesses based on the treatment of secondary materials have also revealed that copper losses are indices of precious-metals losses. Many custom smelters are thus required to obtain more reliable controls for reducing copper losses than ever before. Mitsubishi Materials Corp. has cooperated with academic research institutes in conducting research projects on the pyrometallurgical fundamentals of copper smelting systems, including mutual evaluation of magnetite behavior between synthetic and industrial slags. The state-of-the-art pyrometallurgy has subsequently been introduced to Naoshima smelter for controlling the Mitsubishi process. The revised controls function successfully and the operational results demonstrate that avoiding the discharge of solid magnetite from the S-furnace is quite effective to reduce copper losses. Magnetite behavior has been controlled over the Mitsubishi process so as to reduce copper losses while satisfying the needs of recycling businesses growing in Japan. In-situ estimation of magnetite behavior using the absorbed heat from the melts to cooling water will also be discussed.

Jan 1, 2007

By L Munholand, G. Soucy, P. Quintal

This work presents early results from the first study to optimize the hydrodynamics of a Plasma Lift Reactor (PLR). The PLR is designed to break down organic contaminants in aqueous solutions. New experimental results are presented for air/water tests and for plasma degradation of organic contaminants in Bayer liquor. In addition, a multiphase Computational Fluid Dynamics (CFD) model has been developed which predicts the hydrodynamic behavior in the PLR. These results of this work suggest the PLR is effective at reducing contaminants in the Bayer liquor and that the CFD model adequately describes the hydrodynamic flow.

Jan 1, 2005

By Kristopher John Shelswell

The work in this paper describes the theory, development and analysis of a computer model simulating a mine operation moving material using concurrent decline ramp truck haulage and skipping practices. This simulation was designed specifically to assess the performance of the truck haulage component and to expand on the scope and capabilities of traditional TKM fleet calculations. Haulage fleet simulation results were similar to TKM calculations for the lower to moderate production rate cases. However, comparisons of ramp-up and high production rate scenarios indicated that the simulation model was significantly more sensitive to operating practices and factors not accounted for by calculations derived when using a single TKM figure. Given the proper calibration of inputs and logic, the simulation model was additionally capable of providing information associated with general mine operations efficiency. Further benefits of the simulation model over a TKM approach included logistical assessments such as production schedule feasibility, productivity trade-off quantifications for proposed operating practices, and the validation of mine resource utilization scheduling. The simulation model was able to expand on traditional methods to approach planning and logistics by considering factors such as truck queuing, real-time traffic interactions, random events, and competition for resources on mine productivity.

May 1, 2013

By H. A. Halupka, I. A. Mozer

"At its plant in San Juan, Peru, Marcona Mining Company operates two grate pelletizing furnaces for the agglomeration of 3.5 million long tons of magnetic concentrates annually. Line One, installed in 1963, was built by Lurgi as a downdraft process furnace utilizing a furnace fan for the recuperation of hot gases from the cooling zone. This line was modified in 1966 to include both updraft drying and downdraft drying, and the original roof burners were converted to side-wall burners. Line Two, a Dravo-Lurgi furnace with an annual capacity of 2.4 million long tons, was built in 1966. This line, in contrast to the modified Lurgi furnace, employs direct recuperation of hot gases from the cooling zone and utilization of process gases from the firing zone for updraft drying.At its plant in San Juan, Peru, Marcona Mining Compa-ny operates two grate pelletizing furnaces for the agglo-meration of 3.5 million long tons of magnetic concentrates annually. Line One, installed in 1963, was built by Lurgi as a downdraft process furnace utilizing a furnace fan for the recuperation of hot gases from the cooling zone. This line was modified in 1966 to include both updraft drying and downdraft drying, and the original roof burners were converted to side-wall burners. Line Two, a Dravo-Lurgi furnace with an annual capacity of 2.4 million long tons, was built in 1966. This line, in contrast to the modified Lurgi furnace, employs direct recuperation of hot gases from the cooling zone and utilization of process gases from the firing zone for updraft drying. 5 per cent increased capacity, 30 per cent lower fuel oil consumption, and approximately 400 per cent reduction in grate bar and pallet corrosion. Firing of the pellet bed was improved by conversion from roof to side-wall burners. This modification also permitted utilization of monolithic refractory in place of pre-fired shapes, thereby improving over-all furnace availability and reducing refractory stock requirements from 154 different shapes to 18.Data are presented to compare operating performance of the Dravo-Lurgi furnace and the modified Lurgi furnace. These data show 30 per cent lower fuel oil consumption and 10 per cent higher capacity per unit grate area for the Dravo-Lurgi furnace, which also averages higher availability due to greater operating flexibility."

Jan 1, 1970

By Earle J. Klohn

"The design, construction and operation of tailings dams is rapidly becoming a major consideration for most new mining developments, as well as for many existing operations. In North America, under pressure from public opinion, various government agencies have in recent years enacted legislation covering the design, construction and operation of tailings dams. In British Columbia, comprehensive legislation has been passed during the past year (1971). All of these new regulations may be placed into two broad categories: regulations concerning the safety of the dam and appurtenant structures, and regulations concerning the prevention of pollution. Both types of regulation affect the design of the tailings dam facilities. Consequently, they must be considered jointly by the designer. A good tailings dam design must satisfy the basic requirements of safety, pollution control, storage capacity and economy. To achieve this, 'the design must be based on a thorough understanding of both the geotechnical problems involved and the requirements of the mining development. Obviously, this requires close cooperation between the designing geotechnical engineers and the mining operators. This paper outlines the major engineering factors that should be considered in the investigation, design, construct ion and operation of tailings dams. Basic methods of tailings dam construction are reviewed and the advantages and disadvantages of each briefly discussed. Comparisons are made between the design and construction of conventional water supply dams and tailings dams. Examples are presented of some of the problems that may arise during construction and operation of a tailings dam. The paper also explains the need for basic instrumentation of tailings dams and for carrying out simple field tests and measurements during construction and operation. Of prime importance is the downstream monitoring of surface and subsurface seepage flows. These observations are invaluable where contamination of surface and/or subsurface water may become a contentious issue at some future date. Each tailings dam design must be based on a study of the particular requirements of that project. To make a proper evaluation, adequate data must be available concerning a large number of items•, including such things as: topography, hydrology, geology, subsoil properties, seismicity, government regulations, fineness of mill grind, mill water balance, availability of suitable construction materials, volume of water to be stored behind starter dam, downstream development or liability, and many others. The large number of variables involved in such an evaluation often result in the designer considering two or more alternative designs. Selection of the final design, which is usually based on detailed cost analyses of the alternatives, must be made in close consultation with the owner."

Jan 1, 1972

By A. E. Aho

"The material presented in this paper will be subject to modification as new data become available, but it is presented in the hope that it will inspire more intensive mineral exploration and geologic studies of what appears to be one of Canada's richest mineral provinces. A metallogenic province 400 by 150 miles in extent, lying mostly northeast of Tintina trench, encompasses most of the base metal deposits of Yukon, as well as deposits of other metals. Its main features are northwesterly trending arcuate fold belts, with several orogenic axes, which include most of the metamorphosed rocks, granitic intrusives and mineralization; and which are modified by regional uplifts, northwest-striking fault trenches, and lesser transverse folding and faulting.The main base metal occurrences and their regional controls are summarized briefly. Most of the replacement-type deposits are localized in late Proterozoic to early Paleozoic rocks, particularly Lower Cambrian -probably because these are the most physically and chemically favourable hosts encountered in an appropriate temperature and pressure environment; perhaps because of early age of deposition. Most of the deposits also occur near heat sources or intrusives with associated structural uplift, which has, moreover, served to expose the older rocks. They also tend to occur near known or suspected regional fault trenches, such as Tintina, Macmillan and Hess, although this relationship may be fortuitous. In detail, they may be localized in fold axes, flat-lying beds or other appropriate structural traps. Vein-type deposits are fracture-controlled and localized by dilational localfties, the competence of wall rocks and ""damming"" effects.In the Anvil district, large stratiform iron-zinc-lead replacement deposits lie parallel to gently plunging flex-ures in phyllite in a zone parallel to the Tintina trench, along the southwest flank of the arch-like Anvil batholith. About 80 million tons of massive sulphide ore probably existed before erosion of the Faro orebody, the Vangorda deposit could have been of similar magnitude before erosion and much more tonnage probably remains to be discovered in the district. The Anvil deposits may differ from others found to date in Yukon, but resemble the Sullivan orebody of southeastern British Columbia in their large size, localization in essentially non-limy peptic to arena-ceous host rocks of Proterozoic or early Paleozoic age and proximity to the Rocky Mountain -Tintina trench sys-tem. These features suggest an origin from primordial subcrustal sources.More major ore deposits, not only of lead, zinc and copper but probably of other metals as well, will no doubt be found in similar environments in Yukon or Alaska. Thus, the base metal province of Yukon offers challenging opportunities for prospecting, development, field studies and basic research."

Jan 1, 1969

By Gordon G. Duncan

Historical Sketch Occurrences of native copper have been known along the Arctic coast of Canada, especially in the vicinity of the. Coppermine river, since the early part of the eighteenth century (See map, Figure 2, insert). In 1769, Samuel Hearne, a clerk of the Hudson's Bay Company at Fort Churchill, was sent to explore the 'copper mines' from which natives had been reported to secure copper for tools, fishing spears, etc. After two successful attempts, he reached the Coppermine river in 1771, accompanied by Indian guides. This hazardous trip was indeed a remarkable feat when one considers the vast distance covered, a great deal of which was barren lands. At Bloody falls, (See Figure 1) on the Coppermine river, Hearne's Indians swooped down on a party of sleeping Esquimaux, who gathered there each summer to fish, and murdered the entire band encamped on that side of the river. Hence the name of the falls. Hearne's knowledge of minerals was undoubtedly limited. He reported having seen the copper mines from which the natives were securing the copper, but he failed to prove the economic possibilities of the copper occurrences or to give an accurate description of any deposit. Sir John Franklin visited the area in 1821. He and other members of his expedition, namely, Richardson, Back, Kendall, and Hood, reported native-copper float to occur in the vicinity of the Coppermine river and Bathurst inlet.

Jan 1, 1931

By Oliver C. Ralston

DURING the development of froth flotation for the treatment of sulphide ores, a certain amount of information was collected about a few of the nonmetallic minerals, and occasionally the gangue minerals in the sulphide ores showed an embarrassing tendency to float. However, for many years efforts were expended to develop reagents that would cause wetting and depression of these minerals. Among the nonmetallics, the minerals sulphur, graphite, and talc probably should be classified as 'natural floaters', and perhaps sericite. They respond to almost any type of flotation reagent, and their beneficiation by flotation had been attempted years ago. Flotation of sulphur is now common practice, and graphite was concentrated during the World War in many mills, most of which have now closed down. A talc mill has just been constructed, and another may soon be erected. Second to the 'natural floaters' come the 'easy floaters', cassiterite, fluorite, barite, mica, colloidal gangue, and paper pulp from white water of paper mills. That these materials responded to some of the early flotation reagents, as oleic acid, has long been known; occasional references to their behaviour are found in the very early flotation literature and in that of today. In general, however, nonmetallic minerals, valued at $2.00 to $15.00 per ton, have for a long time been regarded as cheap products and not worth much beneficiation. Consequently, only high-grade natural deposits suitable for direct mining and sale have been gouged out. Furthermore, the mining of these minerals has too frequently been in the hands of 'super-practical' men-men of no technical or other training, willing to work for a very low compensation. From the social standpoint, nonmetallics has been the field for small, untrained enterprisers with little money to spend on plant or equipment. But times have been changing. The impact of technically trained men on the old industry has revealed appalling losses and inefficien-cies and proved the value of processing materials discarded or avoided by the old regime.

Jan 1, 1937

By S. D. F. Rocha1, L. Katsarou, G. P. Demopoulos

"Crystalline scorodite (FeAsO4·2H2O) has been pointed out as the most stable compound to immobilize arsenic for disposal due to its good stability performance according to EPA’s TCLP test. However, in anaerobic conditions, arsenic releasing is increased to undesired levels due to scorodite reductive break down, in eh <100 mV at 5.5< pH <7 which causes contamination of groundwater. In this work, the concept of encapsulation by controlled deposition of mineral coatings immune to pH or redox potential variations is presented. Aluminum and calcium phosphates were evaluated as coatings and the release of arsenic from scorodite previously coated with phosphates was substantially decreased when compared to the VALUES (obtained from crude scorodite, both in oxic and anoxic conditions. INTRODUCTIONThe widely acknowledged hazardous properties of arsenic as a soil and natural water contaminant and its adverse health effects when present in drinking water have led to very strict environmental regulations (Mandal & Suzuki, 2002) aiming at the drastic reduction of the presence of arsenic in the effluents of the mining and metallurgical industries.In Canada, the Metal Mining Effluent Regulations (Government of Canada, 2002) dictate that the maximum monthly mean concentration in tailings for arsenic must be lower than 0.5 mg/L. At the same time the new Environmental Protection Agency’s (EPA) standard for drinking water foresees concentrations of arsenic less than 0.01 mg/L, which means that the leachability limit for the industrial waste is set at 1 mg/L arsenic (EPA, 1994; Le Berre et. al, 2007). One of the preoccupations of the mining and metallurgical industries is directed to the elimination of arsenic presence in all its effluents, especially since arsenic is commonly found in many ores mainly in the form of oxides and sulphides. After processing of arsenic-containing ores and concentrates, arsenic can be present either in solid residues and tailings, liquid effluents or in flue dusts. Several of these forms of arsenic waste materials are soluble and therefore may cause the contamination of ground water, if disposed of without further treatment."

Jan 1, 2012

By J. Jung, W. Keller, A. Zucht

"The agitator design for nickel high pressure acid leach autoclaves (HPAL) is critical with regard to the process result, i.e., the recovery rate. Further considerations during the design phase are the avoidance of acid hot spots which reduce the lifetime, due to corrosion of the wetted parts, including components manufactured from titanium. Besides the process knowledge to design HPAL autoclaves, tools such as, Computational Fluid Dynamics (CFD) supplemented by lab testing allow the design of optimized agitation systems. This paper describes the effect that different feed point locations have on instantaneous blending of the reactants. Furthermore, experiments and CFD show where abrasion issues might occur and how to obtain information about the static and dynamic forces acting on internals. We show how simulations can be validated by lab testing to ensure that the CFD models are applied in an appropriate way.INTRODUCTIONAgitated systems in hydrometallurgical processes have to comply with multiple process tasks and in many cases have to withstand extreme operation conditions such as pressure up to 50 bar, elevated temperatures of up to 250°C and exposure to very acidic or alkaline environments and abrasive ores. The process tasks range from instantaneous mixing of reactants, homogeneous suspensions of up to 65% wt. solids with coarse and heavy particles, enhancing the solid-liquid mass transfer for leaching, dispersing large volumes of reactants (gas-liquid, liquid-liquid mass transfer) and moreover to transport generated heat e.g., from exothermic reactions through the vessel walls or internal heat exchangers if required. For economies of scale, agitator systems have reached sizes of 5000 m³ for large open leach tanks with impeller diameters of approx. 6 m, while autoclaves nowadays have exceeded 5.5 meters in diameter with a power demand for a single compartment drive between 300 - 400 kW. In parallel all process industries require a more efficient use of resources, to generate less by-products and higher yields, while ore-bodies tend to be less qualitative and new process routes (e.g. direct leach) are developed. Besides all these facts the mixing solution must be robust and economic. In this paper we want to address our approach in the development and designing of HPAL agitation equipment."

Jan 1, 2012