Search Documents

By Christopher Sherman

The engineering properties of a geologic material are greatly affected by the presence of macropores. Previous research has demonstrated that the size, location, and proximity of macropores influences both the strength and stiffness of specimens. Knowledge of the distribution of macropores in a specimen prior to testing would be useful for a number of reasons. We are developing a non-destructive method called cross-specimen acoustic tomography (CSAT) currently to determine some (or all) of the macropore characteristics for a laboratory specimen. The CSAT method uses a set of piezoelectric sensors that generate and receive high frequency acoustic waves. We measure the travel times of the acoustic waves through a specimen and then use a commercially available tomography software package to invert the data. The inverted velocity model is then used to locate the voids within the specimen. Two dimensional (cross-sectional) results from plaster specimens containing large macropores of Styrofoam show the technique is promising and worthy of further development.

May 1, 2009

By Y. C. Kim

This paper discusses Air Liquide's patented SPALTM (Surface Protection Air Liquide) technology and process for the inerting of coreless induction furnaces using cryogenic liquid gas. Air Liquide Canada Inc., in collaboration with Riverside Brass and Aluminum Foundry Limited (Riverside Brass), conducted plant trials to demonstrate the applicability of the SPALTM technology for copper-based alloys. Results showed that with SPALTM, Riverside Brass benefited from a significant increase in metal yield as the level of dross formation was drastically reduced. Together with the many other benefits of this technology, SPALTM demonstrated to be a non-negligible cost-effective solution to reduce metal production costs. In an effort to optimize the argon flow, different flow rates were used and the oxygen level above the metal bath was measured to pinpoint optimal flow. The results of metal yield, charge mix, dross formation, and melt temperature are compared with and without argon. The metal yield improvements are dramatic and calculated net savings are presented hereunder.

Jan 1, 2007

By M. J. S. Innes

Abstract This paper is an account of an investigation made by the Dominion Observatory with a gravity meter and magnetometer over sulphide concentrations at East Sullivan, Val d'Or, Que., in June, 1947. The topographic relief over the area does not exceed 20 feet. The overburden varies from 0 co 50 feet. The west orebody had been outlined by extensive drilling. The average density contrast between the sulphide body and surrounding rocks is 0.5. Two hundred and sixty gravity and one hundred and ninety magnetic stations were observed. The results are shown on contour sketches. A derailed account is given of the methods employed to reduce the gravity observations. The survey shows that both gravimetric and magnetic methods are useful in delineating sulphide deposits under the conditions in which they occur at East Sullivan. The results indicate that the buried contact of the syenite intrusive southeast of the orebody could be traced with the gravimeter and chat the magnetometer was of little value for that purpose. Gravity anomalies due to the varying depths of overburden are negligible as compared to the magnitude of the total anomalies. Introduction The project was first suggested at a meeting of the Associate Committee on Geophysics of the National Research Council in September, 1946. At that time it was pointed out that the accuracy and speed of operation of the new gravity meters made them of special importance for geophysical prospecting and it was highly desirable to have an objective test of the performance of an instrument of this kind in delineating an orebody of known dimensions and density characteristics. Several years ago, a private company did some work with a gravimeter over the Amulet deposits, near Noranda. Unfortunately, the topography there is rather rugged, with hills and ravines exceeding 100 feet, so that the topographical effects rendered it impracticable to distinguish between anomalies due to the sulphides and those due to surface irregularities. An orebody of a typical nature, where the disturbing topographical corrections were not excessive, was therefore sought.

Jan 1, 1949

The following guidelines have been recommended by the Diamond Exploration Best Practices Committee established by the Canadian Institute of Mining, Metallurgy and Petroleum. These guidelines are applicable to public companies and their consultants reporting diamond exploration results. In respect of these guidelines, Diamond Exploration Results are results derived from the initial activities undertaken to investigate a diamond bearing prospect or deposit, to generate tonnage, grade and value estimates that cannot be classified as a Mineral Resource or Mineral Reserve. They do not address the earlier stage reporting of geophysical, geochemical or kimberlite indicator mineral results. Public reports of Diamond Exploration Results relating to mineralization not classified as Mineral Resource or Mineral Reserve must address the confidence limits of the result and contain sufficient information to allow a considered and balanced judgement of the significance of the results. The objective of these guidelines is to assist public companies and consultants in making appropriate disclosure of diamond exploration results by reporting in a manner which is: ??Uniform within the diamond exploration industry; ??Consistent with reporting from other industry sectors; ??Comprehensive; ??Unambiguous. The guidelines are not prescriptive. Materiality is the overriding principle that determines the information that should be disclosed. However, where a company or consultant deviates from the guidelines, the disclosure or technical report should state the extent to which the guidelines have not been followed, and the reasons for the deviation. The guidelines do not in any way replace jurisdictional reporting requirements (For example, the requirement for Canadian reporting issuers to comply with Canadian Securities Administrators National Instrument 43-101 by having technical disclosure endorsed by a Qualified Person as defined in that legislation).

May 1, 2003

By Marc R. Laflèche, Suzanne Paradis, A. Shirley Péloquin, Harold L. Glbson, Robin Potvin, Pierre Verpaelst

"The Archean Blake River Group is best known from a central volcanic complex in Rouyn-Noranda. This volcano-tectonic depression, delimited by the Hunter Creek fault to the north and the Horne Creek fault to the south, is interpreted to be a cauldron approximately 20 km in diameter. Its western and eastern boundaries are the Flavrian Plutonand the D'Alembert shear zone respectively. The complex has an exposed stratigraphic thickness of 10.5 km. Two cycles, composed of andesitic units overlain by bimodal, andesite - rhyolite units, are observed in the area, and are, in turn, overlain by an andesitic unit interpreted to be the lower part of a third cycle.The southern sector of the Blake River Group, south of the central volcanic complex, is considered to be outside the limits of the cauldron, but partly contemporaneous with it. The maximum stratigraphic thickness exposed in this area is 4 .6 km. At least two cycles occur in this sector. The oldest unit, a pre-cauldron andesitic to basaltic unit, occurs only in the southern part of the sector. In the north, two partial andesite - bimodal cycles, interpreted as contemporaneous with the cauldron volcanism, are observed.The eastern sector of the Blake River Group, east of the central volcanic complex, apparently overlies the complex. Two units are observed in this sector: a lower bimodal unit and an uper andesitic unit. The bimodal unit is coupled with the uppermost andesitic unit of the central volcanic complex to form a cycle, and the andesitic unit is considered to be the uppermost unit of the Blake River Group. The total exposed stratigraphic thickness in the sector is 2.5 km.The western sector of the Blake River Group, north and west of the central volcanic complex, is interpreted as the lateral equivalent of the complex. Three andesite - bimodal cycles are exposed in this sector, giving a total stratigraphic thickness of9 .5 km. The two lower cycles correspond directly to the central volcanic complex cycles; this correlation is facilitated by two stratigraphic marker units observed on either side of the Hunter Creek fault: the Fish-roe rhyolite flow, east of the Flavrian pluton, and a spherulitic rhyolite lapilli-tuff, west of the Flavrian pluton.Many of the volcanogenic massive sulphide deposits found in the central volcanic complex are spatially and temporally associated with synvolcanic faults, and felsic domes and feeder dykes that are the sites of felsic volcanism in the bimodal units. However, these features also occur outside the central volcanic complex, and the similarities recognized in this work between the complex and the surrounding area suggest that such deposits need not be restricted to the central volcanic complex. The presence of volcanogenic massive sulphide deposits outside the complex confirms this."

Jan 1, 1990

By N. A. Jabit

The dissolution behaviour of ilmenite in acid solutions has been studied by many researchers to improve the leaching efficiency. Most studies which utilized natural ilmenite from different origins resulted in different reactivity due to the alteration caused by the weathering process. Previous researchers have suggested that the greater reactivity shown by some ilmenite samples towards sulphuric acid may be a result of the mineral being relatively unaltered. In the present study a rotating synthetic ilmenite disc of 2.2 cm diameter was subjected to leaching studies in hydrochloric acid. The dissolution rates of iron and titanium from synthetic ilmenite were determined in hydrochloric acid solutions (4 M to 9 M) over a temperature range of 50 to 80°C. Results show that the rate of dissolution of both iron and titanium increased with the increase in acid concentration. However, the rates decreased with time and obeyed a parabolic rate law indicating the blockage of the surface by an insoluble product. The rates of dissolution of both iron and titanium were higher in the presence of SnCl2 and remained unaffected with time indicating the reductive role of SnCl2 which inhibits the formation of surface blocking solids. Application to natural ilmenite is also discussed.

Jan 1, 2014

By X. -G. Chen, J. Qin, K. Liu, D. Racine

"Understanding the thermo-mechanical fatigue (TMF) behavior of materials plays a significant role in the safety design of critical components used in aerospace and automotive industries, such as engine blocks and cylinder heads, which undergo the cyclic change of temperature and stress. However, the cyclic changes of temperature, stress and strain make it difficult using the traditional testing methods to accurately simulate the TMF process. In the present work, the Gleeble® 3800 system was successfully applied to develop a reliable procedure to measure the TMF behavior of aluminum alloys. The modified setup together with the new designed program allows the Gleeble system to precisely simulate the cyclic profiles of temperature and mechanical strain. The novel procedure includes the calibration and verification of the TMF setup to ensure the test validity with Young’s modulus measurement, multi-cycle measurement of the thermal strain and zero stress adjustment followed by online monitoring the TMF cycles. The results of the TMF testing of an AA6061 alloy under cyclic temperatures (60–300°C) and various strain amplitudes (0.2–0.6%) were demonstrated. Its TMF behavior was characterized by the typical hysteresis loops and cyclic stress-strain response.INTRODUCTION The thermo-mechanical fatigue (TMF) behaviour becomes increasing important to evaluate the elevated-temperature properties of materials used as the critical components in automotive and aerospace industries, such as the gas turbines (Hu, Shi & Yang, 2016; Moverare, 2007; Segersäll et al., 2015) and engine blocks (Grieb, Christ & Plege, 2010; Javidani & Larouche, 2014). During the cycles of start-up and shutdown of the engines, these components undergo a complex change of loading. Meanwhile, a dramatic temperature gradient exists on the components due to the cooling system. Therefore, the cyclic changes of load and temperature can give rise to the TMF and may limit the use life of such components (Hu, Shi & Yang, 2016; Javidani & Larouche, 2014; Moverare, 2007). Hence, performing the TMF tests to precisely simulate the cyclic changes of load and temperature to understand the TMF behaviours of materials is playing a significant role in the safety design of these components. For TMF tests, two principal types of cycles are generally employed, including the in-phase (IP) cycle where the load and temperature are at the same phase (i.e. maximum load at highest temperature) and out-of-phase (OP) cycle where the maximum load is applied at minimum temperature (Kliemt, 2012; Miller, 2014). The most significant damage mechanisms in engine components are reported to be OP TMF cycles (Javidani & Larouche, 2014; Kliemt, 2012)."

Jan 1, 2018

By Ted J. Williams

Underhand cut and fill mining methods are used at the Lucky Friday, Stillwater, and Galena mines in the western US in an effort to safely mine in difficult ground conditions and as a primary mining method where access below the ore is limited. The method has evolved at each mine to meet the unique situations associated with their milling procedure and mine layout. Details of the operational aspects of the backfilling and mining cycles at each mine are presented in this paper, accompanied by a summary of the mechanical properties of the backfill and its in-situ geomechanical behavior.

May 1, 2007

By Glenn Kosick, Roger Amelunxen, Glenn Dobby

"The variability in flotation response within an orebody is often a significant problem to address during the design phase of a flotation circuit. In addition, for existing operating plants, the reasons for such a variability need to be clearly understood and accounted for if plant performance is to be optimized. MinnovEX Technologies, in collaboration with major mining companies, is developing methodologies and tools to address the issue of variability in ore characteristics (such as ore hardness and flotation response). The tool is used for design and scale-up of flotation circuits from lab flotation data, and for prediction of recovery and final concentrate grades throughout the mine block model for any given circuit design.INTRODUCTIOTNH: EI SSUEB EINGA DDRESSEDThis paper describes the current development of a methodology and software tool for improved flotation plant design and enhanced prediction of froth flotation performance in an operating plant. The need for this tool is attributed to two primary factors: variability of flotation response properties throughout an orebody and related difficulties with scaleup from laboratory tests. Consider these in more detail.It is well recognized that separation performance via froth flotation will vary significantly within a single mineral deposit. This has been enhanced through the wide application of SAG milling. Throughput with SAG mills is more susceptible to ore hardness changes than is the case with crushing-rod-ball circuits; it is not uncommon to see SAG mill throughput to vary by up to 100% on a regular basis, e.g. 1000 tph to 2000 tph.The implication of this on laboratory testing for prediction of metallurgical performance is as follows: it is unlikely that either the plant grind (size distribution) feeding froth flotation or the flotation residence time will be known at the time of laboratory testing for a given block of ore. Hence, the grind used for the laboratory test is not likely to be that which actually occurs once the ore is processed, and the laboratory retention time may not represent the plant conditions."

Jan 1, 2002

By Yolaine le Beau

Plan de la présentation Le contexte mauritanien La situation de l?environnement en 1999 L?évolution de 1999 à 2010 Bilan La situation de l?environnement en 2011 Le contexte mauritanien Pays du Maghreb couvert à 75% par le désert du Sahara Un des plus pauvres au monde Index de développement humain : 136esur 169 pays en 2010 46,7% de la population ne peut subvenir à ses besoins quotidiens

May 1, 2011

By R. J. Balfour, T. L. Papucciyan

"INTRODUCTIONCapital Cost considerations are basic to feasibility in the achievement of success for Mineral Processing Projects as much as or more than in many other industries. Capital cost is an important factor ae it 1R the unit of measurement for process engineering economic decisions. As a result of ever increasing complexity, alternatives of process and remoteness of site, there is an ever increasing emphasis on accurate estimating and the attendant cost control systems in the international market of today for the Mineral Industry where initial plant costs are becoming a more important factor than operating costs. An undervaluation means trouble ahead. An over-cautious assessment may bring an unnecessary abandonment of a project. Consequently, the ultimate cost must be predicted early and accurately and must be controlled to this parameter during the design and construction phases. Cost Est!~ mating is one of a variety of project management tools used to assist in planning and achieving the optimum balance between Quality, Cost and Time, the eternal triangle of evaluation, namely obtaining a project of acceptable quality at minimum cost and on time. In order to attain these established objectives, proper planning, organizing, coordinating, monitoring, adjusting and controlling the design, procurement and construction elements of the project are essential.This project management approach based upon the principle of a Task Force under single management, comprising a complete service organization, requires a substantial number of qualified individuals specialized in their own field and capable of working together as a team to perform their various functions effectively. The Task Force is supported by their chiefs of discipline and performs in accordance with established procedures and standards under the leadership of a Project Manager.General Engineering Company Limited with the backing of the full resources of Surveyer, Nenniger & Chenevert and its total staff of approximately 1,0009 offers the complete project management service to the Mineral Processing Industry of North America and the rest of the world. As mine sites become more remote and difficult of access, the need for an experienced team of specialists who work under the Task Force principle, with well established standards and procedures becomes even more important. Our long history of successful pro1ecta in this field has been our training ground for the fulfillment of this need."

Jan 1, 1972

By K. Hoover, G. Labarre, S. Rantanen

"As part of the Namew Lake project a mill was constructed to treat 1900 tpd of ore grading approximately 0.90% CU and 2.45% Ni to produce copper and nickel concentrates.Nickel occurs mainly as pentlandite and violarite while copper occurs as chalcopyrite. Two main ore types are present1 lower grade disseminated sulphides in a talcose ultramafic gangue and a higher grade solid sulfide with a granitic breccia matrix.Primary crushed ore from underground is treated on surface in a conventional closed circuit crushing plant using 2-stage cone crushing. Crushed ore is conveyed to storage and then fed at a controlled rate to a grinding circuit employing a rod and ball mill with hydrocyclone classification. Rougher flotation separates and cleans nickel and copper sulfides from waste materials followed by a high lime separation circuit to separate the minerals into final concentrates. Dewatering is achieved through use of high capacity thickeners and pressure filters prior to delivery to a loadout area. The crushing and milling control is highly automated.Plant design was based on metallurgical samples obtained from drill cores. After the first year of operations, plant results compared favourably with design projections.INTRODUCTIONThe Namew Lake Project is a joint venture partnership between Outokumpu Mines Ltd. (Canada) and Hudson Bay Mining and Smelting Company Ltd. (60%). The project included construction of a mine and milling complex to treat approximately 500,000 tonnes per year of copper-nickel ore grading o.91% and 2.44% Ni. Known reserves are estimated at 2. 65 million tonnes. The deposit is located approximately 65 km south of Flin Flon (120 km by road) and about 5 km east of the Manitoba-Saskatchewan border. The decision to construct a concentrating facility was made June 15, 1987 and construction started a week later. The facility, designed for 1900 tonne per day throughput, was ready for commissioning in September 1988. Outokumpu Engineering of Finland was chosen to prepare metallurgical flowsheets, select and develop plant layouts, and provide construction management. Kilborn (Toronto) contributed detailed engineering for civil, structural, mechanical and electrical components and outokumpu Equipment of Canada, the design, the supply, and commissioning of the instrumentation package. Hudson Bay undertook the initial metallurgical test work and preliminary design work."

Jan 1, 1990

By Alan D. Curtis

A standard planning block model for Phelps Dodge North America Operations has been developed to improve mine planning efficiency and performance in a skill starved environment. The model saves time on software management and training, consolidates data and standard information/output, enhances evaluation and strategic process, and improves communication between sites.

May 1, 2007

By C. -K. Fang

"Aging effect on the wear resistance of alumina particulate-reinforced 6061 aluminum matrix composites with a block-on-ring wear tester has been investigated. Specimens with various Al2O3 volume fractions of 0%, 10% and 20% were employed in this work. Experimental results indicated that over-aged monolithic 6061 Al had the best wear resistance, as compared with under-aged and peak-aged conditions. For the composite containing 10% Al2O3, over-aging and peak-aging resulted in similar wear resistance, which was higher than that for underaging conditions. For the composite containing a high volume fraction (20%) of Al2O3, the wear resistance reduced with the increase in aging time. Although longer aging time was favourable to the wear resistance of monolithic 6061 Al, it was detrimental to that for the Al2O3/6061 Al composite with high volume fraction of particles. IntroductionMetal-matrix composites (MMCs) have received attention in many engineering applications because of the demands for high specific strength (strength-to-weight ratio) and specific stiffness, good high temperature capabilities and wear resistance. The manufacturing processes of fiber-, whisker-, and particulate-reinforced MMCs have been well developed (Hosking et al., 1982). Because of the reduction in fabrication cost, the applications of MMCs have been widely extended to light weight-bearing sleeves, calipers, automobile parts (brake rotors, drive shafts, connecting rods, piston rings, and cylinder liners), sporting goods, aerospace components, tanks (wheels, speed brakes, and track shoes) and other industrial applications. Among the three types of metal matrix composites, particulate-reinforced MMCs are promising because of their homogeneous and isotropic material properties and low cost. Additionally, they can be formed using conventional metal processing techniques."

Jan 1, 2003

By C. M. Anson

This paper describes the progresses used in the manufacture of steel wheel-centres, tyres and axles at the works of the Commonwealth Steel Products Co., Newcastle, N.S.W., Australia. The plant is adjacent to the Northern railway and consists of three main buildings, namely: the foundry, the forging and rolling shop, and the machine shop. The foundry contains a 6-ton Heroult electric furnace, together with all necessary mechanical appliances for moulding. Reheating furnaces, steam hammers and tyre rolling mill are installed in the forging shop. The machine shop contains lathes, boring machines, and hydraulic presses. Until this plant commenced operations all wheels used in Australia were imported, previ.ous to the war, from England and Germany, and latterly from England only. Besides being of great benefit to the country in that there is now a domestic source of supply of these articles, there is also the advantage of retaining the home market; and in addition, a small portion of the population are now engaged in highly technical occupations requiring a great degree of skill. The plant began to operate in October 1919, and by 1921 was in a fair way to meet the domestic demand for those articles of railroad equipment which it manufactures.

Jan 1, 1925

By Mark Richards

Highland Valley Copper is a large, open-pit copper mine in the southern interior of British Columbia. Reclamation has been in progress on the site since 1987. Some 6,300 hectares will have been disturbed at the end of the mine?s life, the majority of which will eventually be reclaimed. The establishment of vegetation and the development of a self-sustaining vegetative cover are the central components of the mine?s reclamation plan. The present vegetation-monitoring program for the reclaimed area represents a significant commitment of resources and only addresses a small portion of the site each year. In an effort to expand the area surveyed while improving the efficiency of the monitoring, the use of remote sensing is being investigated. Airborne multispectral imagery was acquired in the summer of 2001, and the results of the multispectral classification were compared to ground observations made during the routine 2000 and 2001 monitoring program. A thematic map with 17 vegetation classes was produced. Within the vegetation classes, there was a strong spectral separation between ? dry grasses? and ?legumes? with further separation according to their density. Green biomass could also be quantified remotely across a wide variety of vegetation types. During summer 2002, further aerial imagery was acquired in combination with a targeted ground-truthing program to determine characteristic vegetation types associated with recognized spectral signatures, which can be used in a supervised classification. It is anticipated that after some fine-tuning, it will be possible to shift the ground-sampling effort from areas where the aerial classification confidence is high to more complex areas.

May 1, 2003

By L. W. Hamel

"Two 35 foot diameter enviro clear thickeners were tested in series as CCD units from June until October, 1978. Up to shutdown in July, we ran with automatic bed level control via the level probes and underflow pinch valves. Despite extensive efforts, we were unable to eliminate the surges created between the units by the opening and closing of the pinch valves. Early in July, the best rake speed and gap setting were determined. After shutdown, the enviro clears were run by manually controlling the pinch valves. These efforts were successful.A few mechanical problems were encountered while operating the thickeners. New units should incorporate more support for the drive coupling and a rubber feed seal. A few modifications of the instrumentation control scheme will be required before the units can be fully automated. A less sophisticated automatic flocculant addition system will accomplish the desired results. Control of the underflow withdrawal via the pinch valve should be investigated further. Our best results were obtained by keeping the feed volume to the No. 1 enviro clear constant. Surges were controlled by opening or closing both underflow valves proportionately.Capacity of the enviro clears is dependent of many variables. The ore treated during the test program was much finer than that reported on in R & D Project Report 76-02. Conditions were never steady enough to determine best flocculant dosage or addition point(s). The lowest soluble losses were obtained at very high wash rates. The underflow densities drop but the soluble losses also drop. Regression equations were developed in order to assess the effect of the various parameters. Within the range studied, these equations will predict the performance of enviro clear thickeners as CCD units on Elliot Lake ores. Our results show that the enviro clear thickeners are a viable alternative to the conventional CCD thickener."

Jan 1, 1979

By Chris Fleming, John R. Goode, James Brown

"Data will be produced from two uranium feasibility studies that were conducted in 2008, both involving uranium recovery from leached slurry by resin-in-pulp (RIP) with strong base resins. Excellent metallurgical results were produced in RIP pilot plants in both studies, and the loaded resins were eluted with strong sulphuric acid and recycled to RIP in an integrated process. Resin losses by either abrasion or mechanical breakage were immeasurably low.Metallurgical results from these two campaigns will be presented, along with an economic analysis of RIP versus the alternative process of CCD or filtration and solvent extraction.INTRODUCTIONThe recovery of uranium directly from pulp with strong base resins in RIP contactors was practiced commercially in the USA in the 1960s, but the process never established itself as a viable alternative to solid/liquid separation and solvent extraction. This was due mainly to the necessity to do a sand-slime separation partially resulting from the unavailability of coarse resin beads, inadequacies in the design of the RIP contactors and screens to separate resin from pulp, as well as problems with the strength and durability of resins in agitated pulps.There have been significant advances in the last 30 years in each of these areas. All the commercial resin manufacturers are now producing very tough, durable, strong base resins, and are manufacturing them in a large bead size that is better suited to RIP applications. In addition, with the emergence and wide spread implementation of the carbon in pulp process in the gold industry in the 1980s, many innovative techniques for preparing leached slurries and separating carbon from pulp have become firmly established. These techniques have proven to be equally applicable to resin separation from pulps in RIP contactors."

Jan 1, 2010

By Sam Palombo, James José Varela

"Washing can be defined as the process used to eliminate or reduce the dirt (presence of fines or slimes) of one material. It is also the basic and oldest process applied to ore preparation for further concentration. This process, in combination with commnution and screening, form the so called washing plant and in many cases produce end products. This work describes the factors that influence the performance of the washing process and main washing technologies used in the mineral processing industry.The Hydro-Clean represents, since 1998, a state of the art technology in this area and is comprised of one of the most innovative solutions developed at HAVER & BOECKER. HAVER & BOECKER design and manufacture technology for mining and related industries. Today the Hydro-Clean is manufactured and sold throughout the Haver Screening Group (HSG) which is comprised of HAVER & BOECKER Maschinenfabrik Münster, HAVER & BOECKER Latinoamericana – Brazil and W.S. Tyler Canada.The Hydro-Clean is a washing technology based on utilization of high pressure water jets. To follow we will discuss how the Hydro-Clean’s different modes of operation result in several advantages related with mine waste reduction, recovery of saleable product, lower capital costs, superior washing results, less stress for the material, a wider range of application and less maintenance cost. Aside from these positive factors, its lower operation costs related to the consumption of energy and water are presented. It is important to note that the quantities, tonnages, data and management concepts presented in the paper are accurate for the time of writing and are subject to change and modification as operations progress."

Jan 1, 2009

By Steve Hubbard, Brad Marchant, Rolando Cuadra

"Triton Mining Corporation acquired the rights to Mina El Limon in Nicaragua in 1993 by international bid. The bid included the gold operations at Limon and an exploration concession of approximately 4000 km2. Triton assumed control of operations and exploration in May 1994.The Limon mine is located in west-central Nicaragua, approximately 100 kilometers northwest of Managua. The climate is tropical, characterized by a wet season from May through October, and a dry season November through April. Gold at Limon is associated with both banded quartz and silicified breccia veins in Tertiary volcanic rocks, belonging to the lower Coyol Group. Mining is from two open pits and one mechanized underground operation. A second underground mine is currently under development for production during 1997.This paper describes the expansion of the milling facility at El Limon from a nominal capacity of 400 tonnes/day, producing approximately 20,000 ounces of gold annually, to the existing 900 tonne per day mill operation. Engineering of the new mill facility was initiated in September 1994 and construction was completed a year later."

Jan 1, 1997