Search Documents

By W. G. Worcester

IN the presentation of this paper to the Institute, three objects are in the mind of the writer: first, to set forth the close relation which, of necessity, exists between ceramics and the industrial minerals; second, to clarify the apparently hazy understanding which many have of ceramics in general; and lastly, of equal or even more importance, to stimulate a greater interest in the industrial minerals, especially in those used and required by the ceramic industries. While Canada is now producing in large quantities a fairly wide variety of the ceramic industrial minerals, there are some which are not known to occur in the Dominion. Hence it is to be desired that our geologists, prospectors, and others, while on field work, should be on the look out for commercial deposits of such minerals as diaspore, bauxite, ucts of a value in excess of $600,000,000, a figure which places ceramics as kyanite, massive topaz, and sillimanite. A find of any of these in quantity would prove of very great importance and value to the country as a whole. At this point it seems desirable to introduce formally the word ceramic or the plural of it, ceramics. In doing so it may be stated that the origin of the word dates far back in history in that it was derived in part from the Greek word Keramos, 'a potter' or 'pottery', which in turn has been traced back to an older Sanskrit root meaning 'to burn' or 'burned stuff', having reference, no doubt, to burned pottery or other clay wares; and the word was so used until near the close of the last century, when the world's first schools of ceramic engineering were established in the United States. The use of the term ceramics was then expanded to cover a much larger field the entire field of the silicate industries and products. At one time it was suggested by a limited number of ceramists that the term 'ceramic engineering' be changed to 'silicate engineering'. This proposal, however, gained little support and was soon abandoned.

Jan 1, 1945

By B. M. Das, F. Claridge, V. K. Garga

Coal, as well as a large part of other minerals in Canada, is produced by surface mining methods. This has resulted in short and long-term accumulation of waste rock in dumps. Two main problems arise from the flow of water through these dumps: stability of dumps and the impact on stream flows. In recent years, a number of mines have started placing waste rock in valleys for general disposal or far constructing mine access road ways. All these have created challenges in the following areas: effective design of dumps and flow-through dams; stability monitoring of the structures; environmental impacts downstream by way of increased amount of fines in suspension, sedimentation, and toxic substances; and long-term status of flow and flood. Similar situations also exist in many civil engineering structures. This paper discusses the status of rock drains and the immediate and future research needs.

Jan 1, 1990

By Keith Donovan

Why are we here? Improve equipment performance & health ? Eliminate undesirable downtime and expensive secondary damage ? Maximize equipment life, optimize running costs (reduce costs) ? Improve safety and environmental performance ? Capture and consistently apply equipment knowledge ? Improve Proactive Maintenance processes & practices

May 1, 2009

By Yannis Faitakis, Simon Bergeron

"This paper describes the implementation of model-based predictive control (MPC) on a vacuum heat exchange network at Alcan's Jonquière Complex. The plant produces alumina from bauxite ore using the Bayer Process.The MPC system was commissioned in 2000, by Alcan personnel and an Advanced Control Engineer from Matrikon. The application has achieved an uptime of about 97%.The benefits were:• Energy savings : 0.5% - live steam reduction• Reduced variation: standard deviation of key temperatures reduced by 50%• Plant throughput increase: via the automated use of surge tanks• Decreased supervision time: by plant operations• Faster and easier diagnosis of problems and plant constraintsThe benefits were higher than expected with a payback time around 12 months.The purpose of the vacuum heat exchange network is to recover energy from a hot stream (pregnant liquor) by transferring it to a cold stream (spent liquor). The system is very tightly coupled, and the main constraints of the multivariable control system are: • to control the many tank levels involved in the process (8 tanks)• to maximize the temperature of the heated streams (spent liquor)• to prevent cooled streams (pregnant liquor) from cooling to below a minimum temperatureThe system includes 9 manipulated, 14 controlled and 2 feedforward variables.The advanced control implementation runs under an expert system environment and provides added flexibility to the overall control strategy."

Jan 1, 2003

By David Lin

"Modal data from Red Dog Main Pit ores were collected and analysed on a size-by-size basis. The Main Pit data were compared to data from composite samples of Red Dog Aqqaluk ores. The data revealed that a large fraction of the sphalerite in the Aqqaluk baritic ore was tied up in sphalerite/galena binaries. This provided an explanation for its poor leadlzinc selectivity compared to Main Pit ores. The Aqqaluk vein ore exhibited levels of sphalerite/galena binaries comparable to that of Main Pit ores resulting in comparable lead/zinc selectivity.An attempt was made to correlate the modal and metallurgical data for Main Pit stockpiles. It was found that there was moderate correlation between the percentage of sphalerite locked in binaries with galena in the <C5>C6 size fi-action and sphalerite deportment to the leadconcentrate.INTRODUCTIONTeck Cominco’s Red Dog Mine in northern Alaska is one of the richest zinc districts in the world. Red Dog Mine has been in operation for over ten years and produces nearly 1 million tonnes of zinc concentrate per mum. Red Dog Mine is an open pit operation and current mining is conducted in the area known as the Main Pit. The Main Pit contains proven reserves of about 41 900 000 tonnes of ore grading 19.2% Zn and 5.2% Pb (Cominco 2000). To the north of the Main Pit is the Aqqaluk deposit. It contains probable reserves of 56 100 000 tonnes of ore grading 16.6% Zn and 4.1 % Pb. After the Main Pit has been exhausted, the Aqqaluk deposit will be exploited.The Aqqaluk deposit consists of three main geologic ore types: baritic, siliceous and vein. The siliceous ore type is dominant, representing 64% of the mineralisation. Composite samples of these ore types were created from drill core and batch flotation tests were performed on them. The flotation tests indicated that there were significant metallurgical differences between Main Pit ore and the Aqqaluk siliceous and baritic ore. The siliceous and baritic ores were found to suffer from poor lead/zinc selectivity (Lin 1999, G&T 1999). It was suspected that there were problems with the original Aqqaluk composite samples, thus a new set of composite samples were created and batch flotation tests were conducted again. In this set of tests, the new baritic ore still suffered from leadlzinc selectivity problems, but the new siliceous ore provided excellent metallurgical results. A summary of the flotation results is given in Table 1. Stockpile 132, which is typical of Main Pit ore, is given for comparison purposes. The mineral suite at Red Dog is relatively simple. The ore consists of galena, sphalerite and pyrite in a silicate matrix. The low zinc recoveries of the baritic ore were largely due to sphalerite losses to the lead concentrate."

Jan 1, 2002

By E. Hardwick, K. C. Sole, Y. Jurrius

"The Luilu cobalt plant at Kolwezi, Democratic Republic of Congo, has been operating since the late 1950s, using a conventional precipitation flowsheet for removal of impurities from the cobalt process stream. Most impurities are, however, incompletely removed using this technology. Copper and zinc, both of which quantitatively deposit at the cathode in the cobalt electrowinning process, are two of the main impurities contaminating the cobalt metal product. Ion exchange offers a modern approach to removing these impurities from the cobalt advance electrolyte.Following a laboratory testwork programme to identify a suitable ion-exchange system, an on-site pilot-plant trial, treating 1500 to 3000 L/d of electrolyte, was operated for a period of six weeks to optimise the operating conditions and to determine full-scale design criteria. Copper removal was carried out using a fixed-bed lead-polish configuration with the Lanxess iminodiacetic acid resin, TP 207. Zinc removal was subsequently carried out in a similar configuration using the Lanxess aminophosphonic acid resin, TP 260. The optimised system proved capable of removing both copper and zinc from 20 to 30 mg/L to <1 mg/L from plant electrolyte containing ~20 g/L Co. Selective elution allows co-loaded cobalt to be returned to the main circuit and value to be obtained for the copper impurity. The process shows operational and economic advantages over the traditional flowsheet. Full-scale implementation of the developed process is in progress and some design considerations are discussed."

Jan 1, 2014

By Ning Shi

This paper suggests an alternative design approach for an innovative shovel dipper, for use in ground conditions where cutting of virgin ground rather than scooping of blasted material is required. Not only does the new design have an optimized dimension ratio (width:height:depth) and attachment arrangement (angle, position), but also a non-linear pro¯le in 2D and 3D. The approach is based on the simulation of a shovel&apos;s duty cycle to verify a pilot dipper model. In order to achieve a realistic simulation that could be used to evaluate a dipper design, the model is e®ectively a descriptor of actual shovel activity under soft ground conditions. The shovel geometry, motion and operation, with an emphasis on digging and dumping kinematics and dynamics are the principal elements of the simulation. The simulation considers a fresh face location, repeating tucking, digging and dumping swing motions within the geometric range of the machine, ending when no more face material remaining within reach without re- positioning. The simulation yields digging force, friction force, trajectory, ¯ll time, ¯ll factor, etc, which may be integrated into two basic considerations: power draw (output) and volume delivered (production), as indicators of dipper performance. The simulation has been used as a tool to modify an existing dipper design, prior to looping further simulation cycles. Ultimately, an optimized or totally-new-concept shape is realized. A prototype dipper as a fractional scale model will be built to verity the performance under actual mining conditions.

May 1, 2004

By C. M. Campbell

In his report on the Coal Resources of Southern Vancouver Island, Mr. J. D. MacKenzie stated that: "For various reasons it has been imagined that the coal deposits of Vancouver Island are extremely large and readily available." "Unfortunately," he added, "neither of these assumptions is correct." The chief disability under which the Island mines now labor does not concern the extent of the deposits. There is ample coal for the present demand. It does, however, concern the availability of the coal. If it were readily available the fuel-oil competition would not be serious and there would be no competition with Alberta, American, Welsh, or Australian coal along the Pacific Coast, for Vancouver Island coal could be produced at a price that would cut out all competition. The outstanding operating difficulty common to all Island mines is the extreme irregularity of the coal seams. To most people a coal seam is synonymous with uniformity, and in most coal seams a condition found at one point will be repeated at other points in the same seam throughout the basin. The accompanying drawings show how very far this is from being true in the Cassidy mine, which, in many respects, is typical of Vancouver Island mines. Figure I is a plan covering about 160 acres of the Douglas seam, the only workable seam in this part of the district. The area shown represents what has been the best producing part of the mine and indicates the very large percentage of the seam where the coal is either entirely lacking or so small in amount that it cannot be profitably recovered.

Jan 1, 1924

By Deon van Tonder, Chuck Edwards

"Solvent extraction is used in many acid leach uranium circuits to upgrade and purify the uranium bearing solution prior to final product precipitation. A number of strip options are available to recover the uranium from the loaded organic. This paper compares some of these options on the basis of typical capital and operating costs for both the solvent extraction circuit and downstream uranium processing, and also considers other related issues. The aim is to provide an objective comparative assessment of these options that could be used as a qualitative guide in process selection or improvement.INTRODUCTIONIn the 1950s the uranium industry was the first industry to adopt solvent extraction (SX). Since then, the flow sheets have advanced. Notable was the introduction of tertiary amine extractants by General Mills during the late 1950s and 1960s (Mackenzie, 1997; Mackenzie, 2005), which is still today considered ‘state of the art’ technology. Initially solvent extraction was done in combination with ion-exchange, such as in the Eluex flow sheet, followed later by the adoption of direct solvent extraction from pregnant leach solution (PLS). From a strip-precipitation perspective ammonia strip followed by ammonium diuranate precipitation was widely adopted as the norm in the uranium industry. More recently alternative strip systems have been receiving increasing attention due to the environmental, health and safety issues associated with ammonia and the resulting calcined uranium oxide product. This paper explores some of these alternative options in comparison with the ammonia route.It is important to acknowledge that each operation is unique, and therefore the information and philosophy outlined in this paper serve to provide a general guide that can be potentially applied and adapted to any site or project."

Jan 1, 2013

By Peter Wells, Laxman M. Amaratuga, Todd M. Kanhai

"Certain mining methods (eg. Cut-and-fill) result in the contamination of run-of-mine ore with shotcrete. This shotcrete remains mixed with the ore throughout processing. Experimentation performed by Falconbridge Limited revealed that underground contamination of ore by shotcrete (eg. as little as 1% by weight) has led to ill-effects on the nickel recoveries from the flotation process in the mill. The nickel recoveries of contaminated samples were lower than tests without the shotcrete Contamination.To optimize flotation circuits it is important to know why the contamination has created these effects and also to find a method to abate or remove them. Laboratory testing showed that the age of the shotcrete was a factor in it’s effect on nickel recoveries. Younger aged shotcrete gave nickel recoveries lower than baseline nickel recoveries with no contamination. Older shotcrete gave nickel recoveries similar to the baseline.Literature on other cementitious material contaminations on ore revealed that a possible means of remediating this problem is the use of acid in the flotation. The initial pH in the flotation pulp was designed to be pH 9.2, but with the young shotcrete contamination the pH was in the neighbourhood of 10.5. Acid addition may act as a means of lowering the pH to the optimal operational value. Laboratory test work showed that acid addition brought nickel recoveries closer to the baseline."

Jan 1, 2000

By Lars A. Bergstrom

High-voltage direct -current transmission is a relatively new technology. The successful development and operation of AC/DC converters, capable of handling large power blocks, have made HVDC transmission generally accepted by utility engineer s and planners around the world. HVDC technology still has significant development potential and, as a result, it is expected that equipment costs will escalate at a substantially slower rate than those of conventional AC equipment. This development will also result in still more compact terminal stations. This paper reviews two modern HVDC installations. In Zaire in Africa. a 1700-km overhead DC line rated at 500 kv, will supply power to the copper mining district in the Shaba region. Another HVDC link connects Norway and Denmark through a submarine cable rated at 250 kv. This is the longest HVDC cable in the world, 127 km, and the water depth , maximum 530 m, is also much greater than for any previous similar cable. The reasons for selecting HVDC are discussed, and the design and layouts are presented.

Jan 1, 1978

By Yuyong Li, Liangman Zhang, Zhaolian Wang, Shun Wang, Ltd. Shandong Huate Magnet Technology Co., Fengliang Liu

"Introduce a newly revolutionary magnetic separator - Raising Concentrate Grade and Decreasing Dregs Content Magnetic Separator Series JCTN (i.e. RCG&DDC MS JCTN). HUATE® JCTN is designed for rinsing, purification, desliming and thickening of the magnetic minerals as per different requirements. Adopting 240°-270° larger magnetic element with multi-poles and magnetic pulsation, and combining the devices of multi-channel rinsing water and top flushing water and new style tank, HUATE® JCTN can improve another 2%-10% concentrate mFe% than the traditional MS without lowering the concentrate recovery rate. Thereby, it solves the uneasy concentrate upgradation problem of the traditional MS resulting from the magnetic aggregation. Now, JCTN has been successfully applied in more than 30 mines in Australia, China and Russia, e.g. Sino Iron of CITIC PACIFIC MINING MANAGERMENT PTY LTD. HUATE® JCTN can optimize the industrial processing line by: 1) improving the discarding rate before milling to discard the necessary tailing ASAP; 2) getting in advance the final concentrate after milling. One JCTN can replace many traditional MS in series. In some way, it can also replace the anti-flotation separation process.INTRODUCTIONWe’re writing to introduce a newly revolutionary magnetic separator - Raising Concentrate Grade and Decreasing Dregs Content Magnetic Separator Series JCTN (i.e. RCG&DDC MS JCTN). HUATE® JCTN is designed for rinsing, purification, desliming and thickening of the magnetic minerals as per different requirements."

Jan 1, 2016

By Michel Carreau

Renewable assets have large upfront capital costs but minimal operating expenses over their lifetimes. In some instances, deals can be structured so that direct capital investment is feasible, with paybacks typically within 5-7 years. In others, the burden of renewable CAPEX must be removed in order to create an attractive alternative to fossil-fuel-fired generation. Hatch has designed and oversees the construction of a renewable installation, which is financed, owned and operated by a special-purpose entity. Renewable energy is then delivered to the mining company via a customized power purchase agreement at a price that is lower than the levelized cost of fossil fuels. In this way, the mining company removes the burden of the renewable energy CAPEX from its balance sheet, thus freeing up capital, decreasing risk, and making the predictable, lower cost of renewable power more attractive than the variable cost of fossil fuels. This paper presents the above business model and success stories of hybrid power at remote sites (wind and solar coupled with diesel engine).

Aug 1, 2013

By Ian Thomson

OBJECTIVES OF EXPLORATION ? Prove/Disprove presence of potentially economic mineralization ? Keep on budget ? Minimize negative environmental impacts ? Gain a ?Social License to Operate? (SLO) WHAT IS A ?SLO? ? Granted by the local community ? Intangible, informal, non-permanent ? Has to be earned and then maintained ? Defined as ? Ongoing Approval (BSR and AccountAbility) ? Ongoing Approval, broad social Acceptance (Joyce and Thomson) ? Ongoing Acceptance (Nelson, and many others) ?Expression of the quality of a ?relationship?

May 1, 2010

By BARRY BANNATYNE

Non-swelling bentonite has been quarried in Manitoba by Pembina Mountain Clays Limited since 1941. It occurs in several thin layers near the base of the Pembina Member of the Upper Cretaceous Vermilion River Formation, and is quarried from the narrow outcrop belt along the slope of the Manitoba Escarpment. It is marketed both as natural and activated bentonite for a variety of specialized uses. Percolation of acidic water through bentonite has produced a naturally activated bentonite with good absorbent properties; these properties are enhanced by treatment with sulphuric acid to produce an activated bentonitefor decolourizing petroleum and vegetable oil.

Jan 1, 1984

By K. D. Peaslee, J. M. Soto, IéDé Smith, A. D. Saikia

Spinel-forming refractories reduce penetration of metal and slags through a tightening of the lining resulting from the volume expansion associated with spinel formation. Sintered spinel is often added to reduce the overall volume increase that results. Tests were carried out to evaluate the difference between performance in spinel¬forming and spinel-containing refractory mixes. Eight refractory linings, one (1) pure magnesia, three (3) magnesia-base spinel-forming and four (4) alumina-base spinel- containing dry vibratable mixes, were tested for four hours in contact with a low-carbon, low-manganese steel in a coreless induction furnace at temperatures in excess of 1600°C. Afterwards, sample were cut, and wear and penetration were measured. For magnesia-based mixes wear was minimized using 20-30wt. spinel formation although further experiments are required to determine the optimal value. For alumina-based mixes, there seemed to be an optimal ratio of spinel added to spinel formed that minimized penetration and wear at the slag line. Sidewall accretion occurred and the accretion was the highest for the mix with the ratio of spinel formed to spinel added near the optimum value. Therefore to design an optimum refractory mix the benefits of higher ratios of spinel added to reduce penetration and wear at the slag line will need to be balanced with the tendency to form accretions on the sidewalls of the furnace.

Jan 1, 2004

By M. Piard

Fires and explosions are not likely to originate in clean gobs above pillar faces steadily driven through a solid panel in order to effect a complete extraction. As. to the storage which such a process implies where the market is intermittent, its cost will never equal that of abandoning large pillars in a fully developed property. Much less will that cost, thanks to the big sizes obtained, ever approach that of cleaning wet and dirty crushings robbed at great expense from small pillars exposed to many years of roof pressure. Even thick seams under bad roof may be fully extracted without the help of filling material. Fatal accidents from falls of roof owing to the great height of excavations, losses in coal, and the danger from fire, have compelled operators in South Staffordshire, England, to discontinue the stall-and-pillar system at one time supreme in the district, and to successfully adopt the following plan: A retreating&apos; longwall is run along the top coal, as the first working; the bottom coal is taken in the same manner, after the fallen roof has become sufficiently consolidated to allow the mine to be reopened. A similar plan is suggested in this paper in order to deal with the outcropping and pitching seams found in the Kootenay measures.

Jan 1, 1930

By Christopher R. Davis

Resource modelling is the basis for any economic appraisal of a mining project and includes a number of steps from data acquisition and validation to resource reporting and classification. At each step in the modelling process it is necessary to define the specific objectives, the methodology proposed to achieve those objectives and to establish a set of checks and validation tools to assess the effectiveness of the proposed methodology. The data used has to be both reliable and relevant for the purpose of the modelling. QA/QC for database validation requires verification of sample location; including correct collar location, topographic modelling and down-hole surveying. Validation is also performed on assaying information such as checks for sampling bias and accuracy of core splits, proper use of pulp duplicates and standards, handling of calculated values, explicit/implicit absent data and data entry errors. The second step involves identifying the mineralized domains resulting from the mineralization process. This step requires a geometric interpretation of all relevant geological features that have influenced the spatial distribution of the mineralization including dykes, faults and alteration. In addition, a geologic reference system rather than a standard Cartesian system is established to measure distances between samples. Once the mineralized domains are established and the database has been validated, statistical and spatial description of the mineralized samples are examined in order to establish the histogram and the variogram of all variables of interest and their correlation. Results are also used to calibrate the global resource estimate within the mineralized domain and to establish the search strategy for grade interpolation. The mineral envelope is filled with polyhedral cells representing mining blocks. The average grade of these blocks is estimated using kriging techniques in order to eliminate global bias and to minimize the local error in the block grade estimate. Visual checks are made to validate the spatial trends in grade distribution while global bias and smoothing effect are assessed from the declustered sample statistics. When required, smoothing correction may be applied using ?change of support? techniques. Simulations are used to perform sensitivity analysis and the simulation models are used if severe smoothing of spatial variability makes the interpolated model inappropriate for mine planning. The keys to successful resource estimation are an integrated team of geologists, geophysicists, geostatisticians and mine engineers using the best available technology and reviews by independent auditors. The resource team is also responsible for performing a QA/QC program in order to measure the effectiveness of the methods in meeting the specific objectives at each step of the modelling process.

May 1, 2001

By K. Webb, M. Hohn

"This paper reviews the evolving Ontario mining regime for mining industry-Aboriginal engagement and its apparent alignment with court decisions, domestic law, emerging international norms, mining industry rules, and mining firm-Aboriginal agreements, drawing on publicly available commentary from government officials, the private sector, and Indigenous communities. This paper provides a preliminary analysis of the potential implications of the new regime, especially for the mining industry and Aboriginal communities and, on that basis, discusses possible future developments.RÉSUMÉ Le présent article analyse le régime minier de l’Ontario pour l’engagement entre l’industrie minière et les Autochtones et son harmonisation avec les décisions des tribunaux, le droit interne, les nouvelles normes internationales, les règles de l’industrie minière et les ententes compagnies minières- Autochtones en se basant sur des commentaires, disponibles publiquement, d’officiels gouvernementaux, du secteur privé et des communautés autochtones. Cet article fournit une analyse préliminaire des implications potentielles du nouveau régime, surtout pour l’industrie minière et les communautés autochtones et, en s’appuyant sur ces données, il traite des futurs développements possibles."

Jan 1, 2016

By W. Almdal

"To compete in the ever expanding global market, companies must continuously improve. Benchmarking, a tool that can help determine where the best areas for improvement are, is more than comparing measures, it is comparing how business is carried out and how decisions are made. The key to success is in integrating benchmarking results into the organization, so that those most affected by the results own them and are empowered to use them as a positive change agent. This is a necessary step to achieving substantive change to practices and achieving optimum performance improvement. IntroductionBenchmarking is a powerful tool that can assist in the continuous goal of improvement. Benchmarking is more than comparing productivity rates or unit costs, it is seeking out best practices and assimilating them into a business to provide a positive change agent.Benchmarking is a continuous process - is time consuming, labour intensive, and requires a lot of discipline. There are no easy answers and no easy solutions, just a lot of work. The results, however, are nothing short of spectacular. More and more companies are adopting benchmarking practices because it is a key tool of the learning organization and will become part of the way business is done, part of the way it is managed. Business must change to stay ahead or to get ahead and benchmarking can accelerate the process of business change. Improvements in an organization can happen faster and more effectively with a benchmarking approach."

Jan 1, 1994