Search Documents

By B. D. Thompson

Many mines adopt necessarily conservative backfilling strategies due to a lack of understanding of their backfill behaviour. In the past five years, extensive instrumentation campaigns have focused on measuring in-situ cemented paste backfill behaviour. These tests have resulted in optimised backfilling efficiency through elimination or reduction of cure periods where; i) controls on backfill behaviour are understood, and ii) barricade pressures are demonstrated to be within a safe range using routine monitoring as a required QA/QC procedure. Recently, this work has been extended to consider hydraulic backfill operations. Two stopes have been instrumented at Vale?s Coleman and Garson Ramp mines. The instrumentation and deployment methods are discussed, and representative total earth pressure, pore pressure, and temperature data are presented. In one case, pressures in the stope are relatively low as drainage causes strength gain in the fill and so pressures are arched. In a second example, again, drainage causes strength gain in the fill, but increasing temperatures correlate with pressure increases even during downtimes in filling. These pressure increases are thought to be caused by thermal expansion of the backfill in confined locations. Generally, the instrumentation approach has proven successful in measuring hydraulic backfill behaviour and offers good potential for incorporation into a procedure to safely maximise backfilling efficiency through routine barricade pressure monitoring, when combined with safeguards to ensure adequate fill drainage.

Aug 1, 2013

By R. Q. Honaker

A significant problem in ultrafine particle classification is the significant amount of submicron particle by-pass to the coarse particle stream. In classifying cyclones, submicron particle by-pass to the underflow stream can be reduced by decreasing water recovery. Past studies have shown that a reduction can be realized when the feed solids concentration is increased or the apex diameter is reduced. However, both adjustments tend to increase the particle size cut point and negatively affect classification efficiency due to the impact on slurry rheology. The addition of a viscosity modifier to the feed stream of a classifying cyclone improved the classification performance and decreased the particle size cut point over a range of feed solids concentrations. The detailed test program investigated the use of the modifier in conjunction with varying apex diameters to identify conditions that minimize ultrafine by-pass. With small apex sizes, roping conditions were readily eliminated by the addition of viscosity modifiers. The addition of the modifier had no deleterious effect on froth flotation performance, which commonly serves as a downstream separation process. The fundamental and practical benefits of viscosity modifiers in classification processes are discussed in this publication.

Jan 1, 2006

By D. Getzlaf

"Oilfield cementing has been utilized in the industry since the turn of the century. Originally, wells were shallow and criteria for well integrity were somewhat limited. Since that time, wells have stretched the envelope in depth, temperature, and pressure. Environmental regulations have also become more stringent, thus, the importance of hydraulic isolation between permeable zones, and between these zones and surface has become more and more important.Initially, oilfield cements were comprised predominantly of construction cement and very limited additives. As time progressed, additives were incorporated to control pumping time or placement time and little effort was placed on optimizing actual components within the cement chemistry. This paper presents issues and concerns created by adding just one new component to the fundamental chemistry of an oilfield cement."

Jan 1, 2004

By P. F. Venus

In December 1977, a large pillar was removed by blasthole mining methods at lnco's Creighton No. 3 mine. Although the 2,363.000-ton blast was not a size record for a single underground blast at Inco, it did represent a significant departure from conventional blasthole mining. In terms of the application of nominal 6-inch-diameter boreholes underground, coupled with bulk slurry explosives, the magnitude of the blast is considered a first and very important development. The application of large-diameter boreholes in underground operations was first tried successfully in 1973. Since that time over 13/4 million feet have been drilled in this adaptation of an open-pit technique to underground operations. The blast, which required 708 holes, totalling 131,500 feet of drilling, was loaded in a six-week period, using special slurry handling techniques developed jointly by Inco and CIL. Inco operating and engineering personnel consider this application of large boreholes and slurry explosives for blasthole mining a very important milestone in modern mining technology.

Jan 1, 1978

By B. H. Weber

"Industry generally has become noise-conscious and is realizing that damage to the human ear is expected to become more costly than any other compensation. Noise control has been recognized as a necessity and, fifteen years ago, in co-operation among different countries, inter-national organizations were set up to co-ordinate measures against dangerous noise and the development of silencing devices began. Rock drills for underground operations were particularly scrutinized because of the explosive nature of the noise developing from air escaping from exhaust. This paper describes the results and the present stage of development in the reduction and control of noise on rock drills, with special application to their use in mines."

Jan 1, 1970

By V. Aitken

Line-of-sight radio control has received widespread acceptance for use in many mining methods because today’s technology offers improved economics and personnel safety. Significant advances in higher autonomy for mining machines are not currently seeing widespread use even though they offer great future potential. With autonomous capabilities being a longer-term goal, a logical sequence of advances based on TeleRemote control is proposed. Under Tele - Remote control, the operator is in direct control of the machine at all times. Three levels of Tele - Remote control systems are presented including line-of-sight, extended line-of-sight, and full load-haul-dump applications. Distributed control and sensing subsystems arranged in a vehicle control area network support incremental system expansion through the three levels of TeleRemote control and prepare the machine for integration of higher levels of automation as mature technology becomes available. This approach allows full exploitation of today’s mining automation technology with a flexible future growth path.

Jan 1, 1998

By T. G. Sitharam, Resmi Sebastian

"Wave propagation studies across jointed rocks have significance in the fields of rock mechanics and geophysics. The passage of a seismic wave induces strains in rocks and often, these strains are of low magnitudes except at the vicinity of source. These low magnitude strains are generally in the elastic range and hence elastic constants necessary for the design and analysis of strength of rock mass, can be derived from wave velocities. Measurement of travel time velocities and measurement of resonance frequencies are the two methods usually adopted for obtaining wave propagation velocities.Resonant column apparatus measures wave velocities from the resonant frequencies obtained during testing. Depending on the type vibration applied, torsional or flexural, shear and compression wave velocities are secured. By varying the amplitude of vibrations applied, various strain levels can be introduced and corresponding resonant frequencies and wave velocities can be calculated. The resonant column experiments were performed on a model material, hardened Plaster of Paris (POP) samples, in laboratory. The paper explains the preparation of samples and the working mechanism of resonant column apparatus along with the estimation of wave velocity from resonant frequency. The numerical simulation of resonant column apparatus using distinct element method and its validation with the experimental results are presented in the paper.A distinct element code is usually used to simulate the movement of materials with intersecting discontinuities. Finite rotations and displacements of individual blocks representing the material are permitted and new contacts between the blocks are identified as the calculation progresses. Three dimensional Distinct Element Code (3DEC), the software intended for the numerical simulation of rock engineering projects, can well simulate the behavior of jointed rocks under static and dynamic loading conditions. The numerical simulation of resonant column apparatus has been performed with 3DEC considering its efficiency in modeling jointed rocks.The numerical modeling of the resonant column apparatus with application of torsional and flexural vibrations to the sample is elaborated in the paper. The response of samples to a range of frequencies is obtained and the frequency that induces maximum displacement in the sample is measured as the resonant frequency, for any particular strain level. The displacements measured at various points of the sample during application of vibrations are compared and presented. The numerical modeling of resonant column apparatus with an intact sample (without joint) and a sample with a joint incorporated are explained at a particular strain level. The resonant frequencies obtained from laboratory experiments and numerical simulations are compared and illustrated. It has been found that resonant frequencies obtained using numerical and laboratory experiments are in good comparison and can be extended for various strain levels and sample conditions."

Jan 1, 2015

By M. Uszko

The climatic area in which Poland is located requires heating the ventilation air at intake shafts during the winter season. Air heating of the intake shaft should ensure safe operation of hoisting devices; while at the same time it also affects the conditions of the mine environment. The paper presents the issues of shaft heating in coal mines in terms of the mining law, the effect on the conditions of the mine environment and heating technology solutions used in the mines of Kompania Weglowa S.A. (KWSA).

Aug 1, 2013

By N. Gharib, F. Hassani, P. Nekoovaght

"Novel rock breakage techniques are becoming more viable and attractive to industry. Microwave energy, as a thermal energy capable of inducing micro cracks through differential heating (therefore expansion) is a technology gaining considerable attention in mineral processing and ore comminution applications. Recently, the use of microwave radiation has been evaluated as a possible avenue for terrestrial and extra-terrestrial drilling applications as well as full face tunneling or rock breaking machines. As part of an overall research on use of microwave in rock breaking systems, the influence of microwave energy on the mechanical properties of common hard rock types as basalt has been investigated. The results revealed that microwave energy irradiation imposes micro and macro cracks to the surface of the rock being irradiated. In explosive free tunneling applications using TBM, jointed and cracked surface of rock eases the cutting process and increases penetration rate. The experimental setups have been simulated with the help of a multi-physics numerical modeling and the results have been compared with practical experiment. The wave propagation of microwave has been simulated and the distances where the power intensity is higher are identified. Experimental and simulation results underlined the potential impact of the use of microwave energy in underground or surface excavation applications such as mining and tunneling. This will also contribute economically when mine-to-mill operation is fully considered to improve the efficiency of rock crusher stages. INTRODUCTIONDuring hard rock breakage (i.e., separation of a piece of a rock from its parent deposit) in mining and civil applications, the performance of mechanical equipment such as tunnel boring machines (TBMs) is limited by high levels of bit wear and maintenance. Preweakening natural rock prior to breaking it by machine is one approach to lower bit wear and maintenance costs. Some preweakening methods apply heat directly or indirectly. For example, flame torch-assisted TBMs (Lauriello et al., 1974; Resource Technology, 1984) have been deemed economical in terms of equipment, but their feasibility is limited by high fuel consumption. Microwave energy could offer several advantages over the flame torch method: it does not produce emissions or increase fuel consumption (electricity source is available on the machine), and is easy to control (quick power on and off)."

Jan 1, 2015

By S. A. Luciani

"In 1957, an asbestos orebody was discovered in the northern sector of the Ungava Peninsula of the Province of Quebec, an area now identified as Asbestos Hill. The deposit is situated on a plateau 1700 feet above sea level and 42 miles inland from Hudson Strait. It is a bleak, iso. lated location of typical arctic environment. Fifteen years were to pass before the first shipment of ungraded fibre was made in 1972. These years we1•e occupied with field surveys and investigations, diamond drilling, engineering design, evaluation of investment and operating costs, and construction. The problems normally associated with mine development were further complicated by location, isolation, and the extreme cold and permanently frozen ground of the arctic regions. Unique to an isolated arctic operation are the organization of support facilities and services, procurement and retention of personnel, construction of access roads and airports, and scheduling of product out and supplies in during the short summer period of sea navigation."

Jan 1, 1976

By L. Cheng, Y. W. Pan, Y. R. Liu

"Impounding deformation of slope and foundation is significant during and post dam construction. Reservoir impoundment is accompanied with various phenomena, including material degradation, effective stress decreasing and buoyancy in rock masses. These phenomena are related with some engineering concerns like reservoir-induced earthquake, landslide and dam stability. The Malpasset dam and Vajont dam are typical hydraulic projects suffering from seepage in dam foundation and slope, which finally led to failure and landslide. Pore pressure in jointed rock masses is considered in constitutive relation. The expression of effective stress for porous rock with fluids is incorporated into the Drucker-Prager criterion. Based on monitoring data of valley width and dam deformation, the effective stress law is applied to analyse the impounding influence of slope and foundation to Jinping-I high arch dam. The dam is accompanied with complicated topographical and geological conditions. The results show that calculated and monitored values agree well, and the application of effective stress law provides an approach to evaluate dam deformation, stress and stability with impounding effect considered.INTRODUCTIONImpounding deformation of slope and foundation is a common and significant problem during dam construction and operation. This phenomenon exists in a lot of reservoirs in China, like Laxiwa, Ertan, Xiluodu and Jinping-I arch dams, and some dams in Europe. It is related with some engineering concerns like reservoir-induced earthquake, landslide and dam stability. The Malpasset dam and Vajont dam are typical hydraulic projects suffering from seepage in dam foundation and slope. Monitored data indicates that the valley width tends to shrink in hydraulic engineering during the impounding process, which will change the stress and deformation of dam and abutment. Therefore, global stability of dam and foundation should be evaluated with impounding process taken into consideration."

Jan 1, 2015

By A. M. King, J. M. Neilsen

"Roughness at varying scales is an important component of the shear strength of discontinuities. Small scale roughness can be assessed in drillcore and through laboratory testing of drillcore derived samples. Large scale roughness, or waviness, also plays an important part in peak shear strength and a number of methods for its incorporation into defect plane strength models are presented.A number of methods for capturing waviness data from exposed faces are reviewed. A method is presented for deriving waviness from downhole televiewer data, which is shown to be significantly more accurate than structural data derived from core logging. The method is based on work undertaken in the highly anisotropic bedded units of the Hamersley Province, Western Australia where televiewer surveys are routinely undertaken. Values of waviness are derived through a review of variation in dip resolved in the direction of the slope face. This method allows design engineers to incorporate large scale roughness in defect plane shear strengths at the design stage.INTRODUCTIONThere are a number of constitutive models currently being applied by rock mechanics practitioners in calculating defect plane shear strength parameters, such as Patton, Barton – Bandis and Hencher [1, 2, 3]. Most of these shear strength determinations are typically undertaken by determining the base or residual friction angle, and applying corrections for small and large scale surface roughness."

Jan 1, 2015

By F. N. Smith

The carbon steel casings of Heat Recovery Steam Generators (HRSGs) in a co¬generation plant were found to have developed cracks that originated on the inside surfaces. The HRSGs receive hot exhaust gases from the primary Gas Turbines (GTs), which are fuelled with pipeline natural gas. The GTs was initially operating without any suppression of nitrogen oxides (NOx). After being in service for about two years, some of the cracks were found to have penetrated right through the 1/4 in. thick casings. The casings are fitted with insulation on the inside (hot gas side). Examination of steel samples cut from the casing walls revealed (i) fine cracks propagating through the steel from the inside surfaces, and (ii) the presence of relatively large amounts of nitrate ion on the inside surfaces. It was concluded that the nitrate ions originated from nitric acid that was condensing on the relatively cool walls of the casings behind the insulation. Nitric acid was formed in the GT exhaust gases by the combination of water vapour (formed from combustion of the hydrocarbon fuel and from moisture in the combustion air) and nitrogen oxides (formed from nitrogen and oxygen in the combustion air).

Jan 1, 2005

By N. Shi, T. G. Joseph

ABSTRACT: An interactive cable shovel simulation has been developed to mimic any shovel dipper geometry for a given cable shovel operating in any homogeneous face material. This interactive cable allows the user to predict shovel performance in any face material encountered and track both its ground stability and the dipper-ground interaction. An embedded Microsoft® Visual Basic spreadsheet was used as the platform for developing an interactive simulation that allows for maximum user-defined parameter input and interactive visual output. The result is an analytical dipper-ground interaction solution that yields crowd, hoist, and digging effort as a function of face activity position.

Jan 1, 2011

By Xiang-dong and Zhu, Xia-jie Hao, Yi-lin Fan, Quan Jiang, Lian-xing Hu, Xia-Ting Feng, Shao-jun Li

"Columnar jointed basalt (CJB), which typically originates from lava flows, is characterized by a special geological structure. The joint network inside the CJB is self-organized into a rough hexagonal arrangement. The field test and measurement during the unloading excavation showed that the columnar joint sets and other internal joint sets not only are important for determining the mechanical properties of the CJB, but also induced its asymmetric unloading deformation and failure. A constitutive model, which considered mechanical deterioration of both the joint sets and rock blocks, was also developed to simulate the unloading behaviour of the CJB. The crack-confinement supporting method for surrounding CJB was developed to overcome the failure of columnar jointed rock mass in the diversion tunnel. Application to the CJB segments of the diversion tunnels in the Baihetan project indicated that this supporting method was reasonable and efficient. INTRODUCTIONColumnar jointed basalt (CJB) rock mass, which typically originates from lava flow, is characterized by a special joint structure. The joint network of the CJB is self-organized into a roughly hexagonal arrangement and leaves behind an ordered colonnade. The widely accepted current view regarding the formation of columnar jointing involves a thermally induced contraction–cooling mechanism (Peck and Minakami, 1968; Degraff and Aydin, 1987; Budkewitsch and Robin, 1994; Lore et al., 2000; Goehring et al., 2006). Although the columnar basalt formation mechanism is fairly understood, the geotechnical characteristics of such rock mass are not well established. In practice, joint sets always induce the multi- failure modes of surrounding rock in the tunneling space (Ibarra et al., 1996; Waltham and Swift, 2004; Mahendra and Bhawani, 2008).According to conventional wisdom in rock mechanics, structural joints affect the mechanical response of rock mass by introducing strong anisotropic effects (Barton and Bandis, 1980; Hudson and Priest, 1983; Brady and Brown, 1985). The columnar jointed rock mass should be considered an anisotropic material given that the joint sets are distributed with some principal directions and characteristic spacing distributions (Cundall and Fairhurst, 1987; Hoek et al., 1998; Wu and Wang, 2001; Budetta and Nappi, 2011; Fortsakis et al.,2012). Columnar jointed rock mass would result in structurally controlled failure patterns, even serious disasters during underground excavation because of the low shear and tensile strengths of intensely joints (Gencer,1985 ;Ishida and Uchita, 2000; Jia and Tang, 2008). The CJB rock mass in the Baihetan hydropower station has exhibited serious stability issues, including sliding, fracturing and even collapse (Shi et al.,2008). Therefore, the geotechnical and geomechanical characteristics of such rock mass should be assessed through in situ investigation and numerical analysis to minimize future accidents during underground unloading excavation."

Jan 1, 2015

By F. Awotwe-Appiah, P. Koshy, J. Dankwah, J. R. Dankwah

This research investigates the generation of an effective carbonaceous material from waste ‘pure water sachets’ and their subsequent utilisation as reductants for the reduction of the Opon Mansi iron ore. Composite pellets of Opon Mansi iron ore and pulverised carbonaceous material generated from waste pure water sachets were heated from room temperature to 1200 °C in a gas fired furnace for seventy minutes. The reduced pellet was analysed chemically for its oxygen and carbon content using a LECO Oxygen/Nitrogen and LECO Carbon/Sulphur analysers, respectively. It was observed that nuggets of metallic iron were readily produced with the carbonaceous materials acting as an effective reductant and source of chemical energy. XRD analysis of waste ‘pure water sachets’ revealed that the polymer was semi-crystalline with peaks that were identical to those of high density polyethylene (HDPE). Gas emission behaviour of the iron ore-PWS pellet was studied in a horizontal tube furnace at 1200 °C using an infrared gas analyser; the results revealed an exhaust gas rich in the reducing gases CO and CH4 along with CO2.

Jan 1, 2015

By B. W. Williams

The crack propagation behaviour of Zr-2.5Nb pressure tube material was studied through comparison of the measured behaviour with the predicted response from finite element analysis. Three-dimensional finite element simulations of compact tension specimens were performed using the crack tip opening angle as a fracture criterion to allow for crack propagation. To obtain reasonable agreement with the measured behaviour, it was important to capture both the anisotropic plastic deformation behaviour of the Zr-2.5Nb material through use of the Hill-48 yield criterion and damage due to void growth, nucleation, and coalescence through the use of a Gurson-based constitutive model in the simulations.

Jan 1, 2010

By Gui Hua Wang, Xin Chang, Zhong Ying Han, Yuan Fang Cheng

"According to the geometrical characteristics of triangular meshes, Triangular Mesh Split Model (TMSM) based on a finite element method is proposed to simulate cracks propagation of fractured rock. With TMSM, stress intensity factors at the tip of cracks are obtained by far-field contour integral. Meanwhile, vector cross multiplication is adopted to fix the cracking unit, and maximum circumferential stress criterion is used to determine the crack propagation angle. Then crack dynamic propagation simulation is realized through local mesh split or node movement at crack tip. With this method, the crack can split apart a unit or extend along the mesh boundary, so the crack could extend along an arbitrary path and is not restricted by the initial mesh. The applicability of the mesh split algorithm is verified by the crack propagation examples of wing crack and multi-fractured rock mass with holes. The results show that this method not only has higher accuracy of fracture parameters calculation, but also can accurately simulate the crack initiation and propagation of rock under complex stress state such as tension, compression and shear. In addition, the far contour integral is introduced to determine the crack tip stress intensity factor and there is no need to reconstruct a singular element at the crack tip or to intensify the meshes. Compared with the existing mesh reconstruction algorithm, this method significantly improves the computational efficiency.INTRODUCTIONGenerally, rock is neither the full continuum, nor entirely discrete body, but rich in geological defects, such as joints and cracks. A large amount of geotechnical engineering practice shows that most fracture of rock is closely related to the internal joints, cracks and crack expansion (Horii et al., 1985; Wong et al., 1998). Although the classical theory of fracture mechanics established the theoretical foundation of crack initiation, propagation, so far it is still extremely difficult to characterize the propagation of airfoil-typed crack and the interference problem of multiple cracks. Up to now, the micromechanics mechanism research of crack propagation of fractured rocks has still been a hot research topic of rock fracture mechanics."

Jan 1, 2015

By F. Barriga-Ordonez, J. A. Finch, L. Calzado, S. R. (Ram) Rao

Sludge, formed by lime treatment of acidic drainage and stored in tailing ponds of the Sudbury region, contains 5-7% Ni, mostly in a mix of hydroxides with Fe (~ 10%), Mg (~ 10%) and Cu (-0.5%), and Ca (-3.5%) as sulphate. Investigations were conducted to recover nickel by a 2-stage process. In the first stage, the sludge was leached with sulphuric acid at pH 3.2. About 90% of the nickel was extracted, producing a solution, which contained mainly nickel (2 g/L) and magnesium (3.7 g/L). In the second stage, nickel was separated by treating with ozone which recovered 99% of the nickel in the Ni(III) oxidation state as -85% pure nickel oxide-hydroxide (NiOOH) precipitate. The oxide settled and filtered readily. A potential use of the product in battery making is suggested. The leach residue contained 0.5% Ni making it less toxic for disposal. Some physical properties of nickel oxy-hydroxide and process parameters including ozone consumption will be discussed.

Jan 1, 2005

By J. L. Luo, D. G. Ivey, A. H. Adeleke

Double-edge-notched flat tensile samples of X70 steel were used for both slow strain-rate testing (SSRT) and cyclic loading testing with the notch located in the zone of interest, i.e., the weld metal (WM), base metal (BM) and heat affected zone (HAZ). By using both optical and scanning electron microscopy, the stress corrosion cracking (SCC) behaviour with respect to crack morphology and various forms of microstructure was investigated. In all the samples considered, the mode of failure was predominantly transgranular with cleavage facets around the edges of the fracture surface. The BM, with a bainitic microstructure, had the highest resistance to SCC when compared with the mixed microstructures of acicular ferrite-primary ferrite and acicular ferrite-grain boundary ferrite observed in the WM and HAZ, respectively. The effect of microstructure on stress corrosion cracking behaviour is discussed based on experimental observations.

Jan 1, 2005