Search Documents

By Jürgen Antrekowitsch, Gerardo R. F. Alvear Flores, Mehmet Ayhan, Christoph Zschiesche

Synergies between copper and lead extractive metallurgical processes enable the processing of a broad range of polymetallic materials. However, this complexity also brings some challenges expressed in terms of complex intermediates and final products. For instance, based on the limited solubility of Cu and Ni in crude lead bullion additional phases will appear during the crystallization of the melt. Beyond the need for continuous optimization of metallurgy the control of phase solidification is a further important pillar to achieve a more efficient process by minimizing the amount and cycles of reverts. This paper describes the microscopy study of one of the most relevant intermediate in the Cu and Pb metallurgy, the Cu based alloy and highlights the importance of applying a well-controlled cooling sequence to improve the overall process efficiency. INTRODUCTION One of the key aspects in Aurubis’s 2025 vision is to move towards the implementation of a multi metal recovery strategy. The implementation of this new multi metal vision is supported by the long tradition of the company, founded in 1866 as Norddeutsche Affinerie, and further developed by adopting modern copper smelting and lead smelting technologies for the processing of primary and secondary materials. The combination of these assets have already build the basis for processing of complex materials in the copper and lead circuits implemented in Aurubis’s facilities. The addition of a new smelting facility, will enhance these capabilities. Aurubis current flowsheet combines Cu, Pb and Zn metallurgy. This includes primary smelting of copper concentrate, processing of secondaries (residues, slimes, slags) and recycling materials (scrap, shredder material, e-scrap). These broad range of materials contain not only the mentioned base metals but also a number of minor metals that requires to be properly managed to ensure efficient recoveries and quality of the targeted metals.

Jan 1, 2019

By A. Brown

THIS P APER has been pre-pared as a progress report on Mines Branch investigations into problems of ground stress in certain co al mines of Western Canada. As such, it should be considered as a companion report to the one ( 1) presented to the Mining Society of Nova Scotia in 1956 and which dealt with similar investigations in the coal mines of Eastern Canada. For the past 50 years, dynamic incidents in the form of 'bumps' and 'outbursts' have been occurring in the coal mines of the Inner Foot-hills belt of tl1e Canadian Cordillera. As these phenomena generally become more frequent with in-creased thickness of overburden, a limiting depth of mining of 2,500 feet has been set (2) for estimating recoverable reserves of coal. If such a view were accepted, from a long-term viewpoint very large resources of coking-grade ?coal -in a part of the continent deficient in such coals -would not be available to the nation. The terrain in which these in-6dents take place may be described in geological terms as being dominated by pronounced structure in strata ?consisting of a large proportion of highly indurated rocks. The Geological Survey of Canada has co-operated by carrying out structural studies (3) at the mines, supplemented lithological by stratigraphic observations.

Jan 1, 1958

By M. Jackson, R. McDonald, T. Osken, D. Robinson

"The addition of sulphidic materials in the leaching of nickel laterites has several potential benefits that include improvements in the rheological behaviour of the blends, reductions in the sulphuric acid and steam requirements, sweetening of the nickel grade of the combined feed material, and the option of using a range of sulphidic materials. The current study examines the oxidative processing of 30% w/w blends of nickel concentrate and nickel laterite ore at 250oC. In particular, the viability of using low oxygen overpressures was examined for significant amounts of nickel flotation concentrate, up to 12% w/w. Further to this the impact of process water quality, in particular the presence of chloride, upon the kinetics of extraction and the mineralogy of the residue were also investigated. This paper will present the results of preliminary work in this area.INTRODUCTIONThe use of sulphidic ore as a source of sulphuric acid during oxidative hydrometallurgical processing is not a novel idea and can be traced back over forty years (Seidel & Fitzhugh, 1968). A series of patents pertaining to application of this approach for laterite ores can be subsequently found (O’Neill, 1973; Opratko et al., 1974; Rodriguez, 2008a, 2008b; O’Callaghan, 2010; Liu et al., 2011) and a few of articles containing published data (Ferron & Fleming, 2004; Quinn et al., 2009). The use of pyrrhotite tailings as a source of sulphuric acid has also been employed for the leaching of converter slags (Perederiy et al., 2011).It is known that hydrometallurgical operations such as the HPAL plant at Murrin Murrin have added small amounts of sulphides as either transitional (mixed sulphide/oxide) ore or non-smeltable concentrate. This can improve the rheology (Rodriguez, 2009) and provide heat credits. However these plants are generally limited in their ability to add such materials due to their reducing nature and given under highly acidic conditions that the breakdown potential of the titanium used for the autoclave lining is significantly reduced. A suitable oxidant must therefore be present to ensure the potential remains sufficiently high."

Jan 1, 2012

By Hilden. M.

"As the Cadia mill was the first 40ft diameter SAG mill, commissioned in 1998, its performance, liner and discharge design attracted considerable international attention. Twelve years on, the liner design and the control philosophy are being readdressed to further improve the mill’s performance. A comprehensive series of 3D liner scans, over life of the liner, have been used to calibrate liner mass loss and progressive changes in the liner profile. This data is being used to provide true charge mass and mill filling, plus progressive trajectory profiles over life of liner. This information, along with measures of mill performance over liner life, is being used to select the optimal operating conditions as the liner wears, and hopes to inform future liner design. INTRODUCTIONSince the Cadia mill was the first 40ft diameter SAG mill, its performance, liner and discharge design has attracted considerable international attention, as reported in previous SAG conferences. The mill experienced particular challenges with regard to pebble and slurry discharge, which necessitated a discharge redesign, incorporating a considerably greater pebble port open area and curved pulp lifters (Hart, Valery, Clements, Reed, Song & Dunne, 2001). Packing between lifter bars on the shell liner was found to dramatically reduce mill throughput over the first half of the liner life. In response, the liners were redesigned to a 2/3 spacing so as to open up the space between lifters. Due to ongoing high liner wear issues, the liner was redesigned based on the discrete element modelling (DEM) of Conveyor Dynamics conducted by Nordell and Potapov (2001). This aimed to maintain mill throughput with new liners and provide an extended liner life. This design was kept proprietary for many years, so has not been open to review."

Jan 1, 2012

By A. A. Lavrinenko, N. I. Gluhova, L. M. Sarkisova, D. V. Makarov

"The investigated sulfide Cu-Ni ores are characterized by low PGE contents and emulgated impregnations of pentlandite and palladium minerals in the main ore-forming mineral pyrrhotite, which hinders their selective separation, requiring a collective flotation of sulfides to concentrate, and hydrometallurgical processing. As revealed by studies of floatability of Pt-Cu-Ni ore in a mixture of butyl xanthate and chelating phosphorus containing reagents, the most effective additive is Aerophine 3416 (a phosphinates mixture) manufactured by Cytec. Using collective flotation with a butyl xanthate – Aerophine 3416 composite in the ratio of 1:3 has afforded to enhance the Pt, Pd, and Ni recovery by 13.6 %, 9.2 %, and 9.4 %, respectively. The optimal ratios of Aerophine 3416 to butyl collector for the collective flotation are the following: 1:1 for Pt and Pd and 3:1 for Ni. The effect of these reagents on the electrode potential and surface hydrophobicity of pyrrhotite, pentlandite, and platinum black has been investigated. The extraction UV spectrophotometry experiments demonstrate that DIBDTPI exists on the pyrrhotite surface mainly in the form of disulfide in weak acid medium and in the form of compounds with Fe on the mineral surface in minute amounts. There appears some disulfide and few amount of (DIBDTPI)2Ni on the surface after interaction of DIBDTPI and pentlanditeINTRODUCTIONXanthates are widely used in flotation of copper-nickel ores containing platinum group metals (PGM) as sulfides collectors which can concentrate the most part of PGM connected with the sulfides. Though xanthates are hardly efficient for flotation of free PGM, the latter are floated more slowly compared to the sulfides of base metals. The reasons for poor floatation of free (mineral) forms of PGM are under-researched, however the key accepted reasons are: fine disseminations of free PGM, insufficient interaction with xanthate and negative influence of blue copperas and sulfur-containing ions which are sulfides oxidation products (Penberthy et al. 1999; Shackleton et al., 2007). That’s why an additional collector, normally dialkyldithiophosphates, is used during flotation of PGM-containing copper-nickel ores. A reagent DP-4 is used for recovery of PGM at Norilsk mining and metallurgical plant. The reagent represents a slightly-soluble organic calcium sulfonate which is given to flotation pulp in the form of water emulsion of 5% - solution in automotive diesel oil."

Jan 1, 2016

By S. Caron, M. Bourassa, J. Châteauneuf, L. Tardif

"Since many years, the Yvan-Vézina gold plant custom mills and processes different ore types that show different behaviors. Because of this, cyanidation control is more complex than for a typical milling operation. In 1992, a Cyancor™ on-line « free cyanide » analyzer has been installed for monitoring and optimizing cyanidation. This implementation significantly reduced cyanide consumption for the overall cyanidation process. In order to further reduce cyanide costs, an automatic control strategy has been implemented to decrease fluctuations of« free cyanide » from their set points.This paper outlines the major steps of the project: process control audit, control strategy development, implementation and running-in period. Control strategy features include data filtering modules, adaptive PID algorithm and set points management modules are also presented. Finally, the strategy efficiency is illustrated with load-disturbance responses.IntroductionLocated in northwestern Quebec, the Yvan-Vézina plant has an average capacity of 1300 t/d using carbon-in-pulp technology. In 1991, the Yvan-Vézina gold plant was processing three types of ores (Beauchemin, Mouska and Silidor mines) and a pyrite concentrate (Beliveau mine). A cyanide reduction program was then undertaken to reduce « free cyanide» fluctuations <6>. To reach this objective, the optimum cyanide concentration was determined for each ore, a continuous monitoring method with the Cyancor™ on-line analyzer was developed and a tighter control of cyanide addition was applied. These modifications to the leaching practice significantly reduced cyanide consumption.After a while, it was observed that regulation of « free cyanide » concentrations could still be improved by the use of an automatic control strategy. Yvan-Vézina and CRM began collaborating in 1995 to develop and implement such a strategy. Results show that main disturbances of the circuit (e.g. ore mineralogy and pulp feed rate) can be significantly overcome in order to reduce their effects on the leaching operation."

Jan 1, 1998

By P. R. Brito-Parada, A. Norori-McCormac

Positron emission particle tracking (PEPT) has become an important tool for flotation research, as it is able to resolve directly the behaviour of particles in laboratory scale flotation vessels. The first applications of PEPT to flotation showed only the motion of an individual particle in the pulp and the froth, but nonetheless allowed interpretations of behaviour not previously possible. Since then, PEPT measurement and data analysis techniques have improved significantly and now ensure a high level of confidence in the particle behaviour obtained. In particular, statistical analysis of long-duration experiments allows time-averaged data to be collated, ensuring spatial accuracy and allowing rigorous comparison of different conditions. It will be shown that these PEPT techniques can be used to compare directly the effect of operating conditions and particle properties in a laboratory flotation system. Particle tracks will be illustrated, as well as analyses of particle speeds, average flow streamlines and occupancy that show marked differences in behaviour near the interface and impeller.

Jan 1, 2015

By G. H. Hope, D. Green

"Recent process advances at Lac Minerals Est Malartic Division are discussed. The Est Malartic mill treats massive sulphide, copper/gold ore from the Bousquet 2 mine, to produce a gravity gold product, a copper flotation concentrate and a gold precipitate. The mill operation has been improved by the application of Knelson concentrators to replace jigs, the application of Outukumpu high grade tank cells and optimizing the cyanide leach to minimize cyanide consumption.IntroductionThe Est Malartic mill is located near the town of Malartic in the Abitibi Region of north western Quebec. The mill has been in production since the mid- J 930's processing mainly clean, free milling gold ore. Active mining from the Est Malartic mine ceased in 1980 and the mill was switched to custom processing of ore from La Mine Doyon located some 45 km to the west. This custom processing arrangement continued until 1987 when the expanded mill at Doyon became available to process all of the Doyon production. In 1987, Lac Minerals commenced development of a second mine at the Bousquet site located 40 km west of Malartic. This mine, Bousquet 2, is the down dip extension of the La Ronde mine developed by Agnico Eagle. During pre-feasibility evaluations, it was determined that modification of the Est Malartic mill to handle this new ore source was economically more attractive than building a new facility on site. Modifications to the mill to process the high copper/gold ore from the Bousquet 2 mine began in late 1989 and the new circuits were commissioned in mid-1990. Modifications included the addition of both gravity and flotation concentration circuits to recover coarse, free gold and the copper. The existing leach circuit continued operating on the copper flotation tailings with some minor modifications to the solution handling systems. An SO,/air cyanide destruction circuit was also added at this time."

Jan 1, 1993

By S. D. Anitha Kumari, T. G. Sitharam

"The huge urbanisation of the world cities have invariably resulted in enormous requirements of development in transport and other facilities. As the surface space available for the construction of these infrastructural facilities is found to be inadequate, underground space is widely used recently for this purpose. However, to understand the behaviour of these underground structures through experiments under various loading conditions is not practically feasible. Hence numerical methods have widely been used to model these structures and predict their behaviour. The underground structures generally rest on soil or rock. Depending upon the properties of the material surrounding the tunnel, the deformation pattern and the stress contours vary. If the tunnels are placed on soft ground at a shallow depth, the presence of existing structures will add to the stresses and strains developed. In the case of densely populated cities, tunnelling operation may result in huge damages if the settlements are not within the desirable limits. This may in turn lead to the collapse of the tunnel along with adjoining structures. So the determination of stress levels associated with the yield of wall due to excavation is very important and necessary supports and reinforcement should be provided. Numerical simulations using discrete element method (DEM) and finite element method (FEM) have been done to understand the stress variation around single and twin tunnels. Studies are also done to quantify the improvement of stability on the introduction of lining around the tunnels in a weak cemented soil mass like sandstone.INTRODUCTIONMost of the life line facilities which include pipelines for electricity, water, communication, sewage, gas, roads, metro, utility tunnels etc in modern urban areas are underground structures. Infrastructure development is crucial for any city and sustainable development urges for underground constructions. Accordingly, there is already a great demand for tunnels to be constructed in difficult and crowded urban settings. This results in the fact that a large number of risk factors are associated with tunnels in these densely populated urban areas. These constraints pose threats to tunnel construction and also demands for minimal disturbance to the public and to the surrounding utilities. One of the most important factor to be considered while designing an underground structure is its stability with respect to the surrounding medium and adjoining existing structures. In this study, a comprehensive presentation of the numerical modeling of single and twin tunnels adopting two different methods is presented."

Jan 1, 2015

By K. Kudo

Magnesium rods of 99.95% purity and approximately 6 mm in diameter were continuously cast at rates of between 15 and 25 mm/min by a heated mould process and their mechanical properties evaluated. It was found that rods cast at 15 and 20 mm/min consisted of a single crystal, while rods cast at a speed of 25 mm/min were multi-crystalline and showed a unidirectional structure. Although room temperature tensile ductility to fracture varied widely, it was found that with an appropriate crystal orientation, cast rods can exhibit elongation by as much as 215%.

Jan 1, 2006

By R. Hans

Removal of toxic anions from aqueous solution was studied using a Magnetic Ion Exchange (MIEX) resin which is a polyacrylic, strong base resin. Gravity based settling is made more efficient due to the magnetic nature of the resin which is advantageous over conventional ion exchange resins. In addition, the magnetic microspheres of MIEX have larger surface area in comparison to conventional ion exchange resins. Over the years MIEX has been successfully used and has gained significant popularity for efficiently removing dissolved organic matter from wastewater and groundwater. In the present study the efficiency of the MIEX resin was tested for the removal of chromium(VI), molybdenium(VI), vanadium(V) and arsenic(V) anions. Effects of pH (2-10) and temperature (25oC-55oC) were examined. In general, low solution pH values were favorable for anion uptake by MIEX. Except for chromium(VI), the metal ion uptake was significantly increased by the increase in solution temperature. The adsorption data were analysed on the basis of chemical speciation and heterogeneous kinetic models.

Jan 1, 2014

By R. E. Molnar, P. A. Riveros, V. M. McNamara

"This paper describes some recent research done at CANMET in the areas of ion exchange and A VR (Acidification- Volatilization Reneutralization), as applied to the recovery of gold and cyanide, respectively. It also discusses the ways in which these two technologies may be combined in order to minimize the environmental impact of gold milling operations and optimize reagent usage. IntroductionGold milling operations can essentially be divided into those that carry out a liquid/solid separation after leaching and those that recover gold directly from a leach pulp. The former produce a barren solution which may contain considerable amounts of cyanide, either free or cornplexed with metals. The latter produce a similar solution but this is now part of a slurry rather than a clear stream. Due to its toxicity, any excess cyanide must be destroyed before the effluent is discharged into the environment. Ideally, this should be (and sometimes is) accomplished by natural degradation. However, in many cases natural degradation alone cannot remove the last traces of rnetallocyanide compounds from the effluent and , as a result, most Canadian gold producers utilize a supplementary chemical oxidation system. This not only increases the operating costs, but concerns have also arisen in recent years about the formation of ammonia as a result of the chemical oxidation of cyanide (via CN--CNO--HCNO-NH3) ·"

Jan 1, 1993

By A. Montini, M. H. Moys

"A conductivity probe mounted in the shell of the mill has been used to measure the behaviour of the load in the mill as a function of operating variables. It was found that certain properties of the conductivity signal correlate strongly with the per cent solids of the slurry passing through the mill; in particular the angular location ?D of the shoulder of the load is an increasing function of the per cent solids. A method for measuring the viscosity of the pulp discharging from the mill has also been developed. The use of the measurements in mill control is illustrated by simulating various control strategies for open circuit milling. It is shown that the use of ?D allows very tight but imprecise control of the slurry rheology in the mill, while the use of viscosity is subject to severe limitations in speed of response. A cascade control system involving both measurements provides adequate control of slurry rheology within the mill. Applications to closed circuit milling are discussed.IntroductionMultivariable control of milling circuits continues to receive a lot of attention in the literature. Hulbert and co-workers and Niemi, et al. have described the use of Inverse Nyquist Array (INA) techniques while Herbst has recently described the use of Optimal Control. It is significant that in neither of these three projects was any variable associated with the grinding mill itself (e.g. power or properties of the mill discharge) used in the control strategy. Pauw, et al.do, however, use mill power in their multivariable peak-seeking controller for pebble-mill control. Little work has been published on the use of measurements of the properties of the slurry being discharged from grinding mills, in spite of the fact that milling efficiency is known to be strongly affected by slurry rheology».Moys has recently developed a technique for measuring the dynamic behaviour of the load in the grinding mill. This method involves the monitoring of the response of a conductivity probe mounted in the shell of the mill which gives a measurement of the orientation of the load inside the mill. It was found that the load behaviour was strongly influenced by slurry rheology. In this project a technique was also developed for the measurement of the viscosity of the slurry in the mill discharge. It was, thus, decided that it would be worth investigating the use of these measurements in mill control schemes since direct control of the slurry rheology in the mill must inevitably increase the efficiency and productivity of the grinding circuit as a whole.This will be done by using the dynamic responses measured by Moys and Montini to simulate the behaviour of an open circuit ball mill. While the control of open circuit mills is of little interest, this simulation provides a simple but powerful demonstration of the advantage provided by these measurements, advantages which should apply to closed circuit operation of any mill type (including autogenous milling). Investigations into multivariable control of a closed circuit ball mill are currently nearing completion and will be published soon."

Jan 1, 1987

By L. J. Heaslip, J. M. Toguri, T. R. Meadowcroft, R. L. Addinall

"""Pilot Plant Operations"" is a final-year core course given to the Metallurgy and Materials Science students at the University of Toronto. This course involves a laboratory study of an industrial project at an industrial site. Details of this program are discussed and reviewed after eight years of experience. IntroductionEducators in the field of Metallurgy and Materials Science have long agreed that ""hands-on"" experience is an important component in the education of metallurgical engineers. This philosophy is reflected in the undergraduate curricula of most metallurgical schools. The major problems encountered with laboratory-associated courses are the requirements for equipment, space and funds for both purchase and maintenance of equipment. For example, consider an exercise in crushing and grinding treatment in a mineral processing laboratory. Such operations require the handling of tons of material and often equipment of large size. The problems of storage of ore, methods of handling and maintenance of equipment are a few of the concerns facing the department. Considering that metallurgical departments at universities are, in general, relatively small, the support to purchase and maintain largescale equipment becomes an annual budgetary concern. In reality, universities today are not geared to operate mini-pilot plant equipment, either in terms of space or personnel.For the above reasons, in 1972an undergraduate core course called ""Pilot Plant Operations"" was introduced to the fourth year curriculum in Metallurgy and Materials Science at the University of Toronto. This course consists of I to 2 full weeks (8 hrs per day) of pilot plant laboratory study at an industrial site on a project of mutual interest with the industrial organization whose facility is being used. The first 5 years of the program were carried out at the pilot plant facility at the Ontario Research Foundation; Stelco&apos;s Research Centre in Burlington, Ontario, was used for the last 3 years. The nature of the projects undertaken during the 8-year period is shown in Table 1."

Jan 1, 1980

By Lauri Gregg

How Can Man Meet the Carbon-Free Energy Challenge ? ? Increases in Energy Efficiency can displace 1/2 to 2/3 of the Carbon-Free Energy required to stabilize at 550 ppmv ? Renewable Energies require too much land and thus can displace 5 to 10 % of the energy requirement ? Large new sources of carbon free energy are needed ? Conservation is desirable but provides only a small and variable contribution ? People will have to adjust to higher levels of CO2 in the atmosphere as energy demand continues to grow

Nov 1, 2002

By Dale A. Sketchley

"Abstract - Large differences in gold content between rock fragments or small volumes of unbroken rock, commonly referred to as the nugget effect, are related to sample and subsample weights, crushing and pulverizing sizes, and density, shape and size distribution of gold grains. Gy’s sampling theory, which relates gold grain characteristics to sample weight, fragment size, and error, provides a method of estimating a sampling constant that quantifies deposit characteristics that contribute to the nugget effect.Sampling control tests provide methods for determining the sampling constant. Sampling control charts, comprising nomographs that relate sample weight, error and particle size, use the sampling constant to optimize sample weights and comminution sizes, and to minimize the variability introduced by incorrect or inadequate sampling and sub-sampling procedures. The sampling constant is useful in classifying ores into arbitrary categories according to expected sampling difficulties. Spatial variations in the sampling constant can be used to aid in defining ore types for modeling geological domains, which should have unique sampling protocols. Examples that illustrate the relationship between the sampling constant and expected sampling problems, and the spatial variation of the sampling constant, are given for various deposits. Case histories of sampling programs are presented.Quality control procedures consist of monitoring sample contamination amd accuracy and precision of analytical results. Accuracy, precision and contamination are monitored by including standards, duplicates and blanks into batches of samples being analyzed. Analytical results of standards and blanks are plotted on a batch-and-time basis with control lines at plus or minus two/three standard deviations as confidence limits of the accepted round-robin value. Examples are given that illustrate a laboratory system in statistical control and the various types of problems encountered when interpreting quality control data. These include sample transcription errors, degradation, contamination, sampling errors, detection limit problems, instrumental drift, lack of statistical control, laboratory bias, procedural problems and data tampering.Where bias is negligible, precision, as a function of concentration, can be obtained from duplicates using the Thompson-Howarth precision algorithm, which also allows calculation of the practical detection limit. Examples are given that illustrate variations in precision, with grain size, for different types of duplicates, as well as mineralogical changes and sampling errors."

Jan 1, 1998

By Alireza Sarafi, Alijan Aftabi

"A hydrocyclic system used for mineral separation at the laboratory scale results in the separation of more than 90% of micas. The system functions only by water and might offer advantages where other methods of mica separation are not available. INTRODUCTIONVarious methods for the separation of micas, wollastonite, and garnet, e.g., screening, flotation, magnetic separation, and heavy liquids, are well known (e.g., Spence, 1929; Bates,I960; Gillson et al., 1960; Benjamin, 1971; Connor and Kolhnar, 1991; Collings and Andrews, 1991). However, where these methods are not available, the separation of micas by a hydrocyclic system developed by Sarafi and Aftabi (1991) may prove to be economic. This note is a brief description of the hydrocyclic system. Minerals and MethodFor testing the recovery of mica and other minerals from different rocks (garnet-mica schist, skarn, and pegmatite), standard minerals were tested first, and then rock samples. Pure mineral standards were prepared from coarse-grained samples of pegmatite, mica schist and skarn; the grain size of the minerals separated was more than I cm. The Hydrocyclic System and Mineral SeparationThe hydrocyclic system is shown schematically in Figure 1. In the first step in mineral separation, mineral and rock samples were crushed, milled, and then sieved to minus 250 plus 125 microns. Approximately 10 gm to 25 gm of the sample were inserted in decanter Dt • The motor pwnps, M1 and M2, were then turned on and the water valve rl was opened. At this time, water was flowing turbulently (30 em3/sec. to 50 em3/sec.) and minerals were separated according to their crystallographic nature, density and!or habit. The fInal separation was done by exit valves r2, r3 and r4, while the motor pwnps were still operating. After each experiment, the rt , r2&apos; r3 and r4 valves were closed and the motor pumps were turned off. Following this, minerals in each decanter and the mter were collected, dried and weighed. The whole time of the experiment was optimized to be about 10 minutes, but varied from 3 to 15 minutes for micas and garnets. respectively."

Jan 1, 1994

By Bill Almdal

Today?s presentation ? Role of the Regional Issues Working Group ? What does RIWG do? ? How can RIWG?s work benefit Stakeholders? ? Review of forecasts vs. reality ? How have past investment compared to the reality? ? Risks to future growth ? The growth potential is very high and so are the risks ? Examples of outputs ? Housing needs ? Growth in population ? Tires for large trucks The Regional Issues Working Group ? Our vision ? To provide a proactive process which promotes the responsible, sustainable development of resources within the Regional Municipality of Wood Buffalo for the benefit of all stakeholders ? What we do ? Facilitate planning for growth ? Facilitate effective and efficient resolution of issues ? Involve all of the resource developers and affected stakeholders in planning ? Develop plans for sharing benefits with Aboriginal stakeholders ? Benefits for Stakeholders ? Our forecasts include up-to-date information from all developers ? including information on employment and housing needs ? Our forecasts are the basis of planning for many stakeholders ? and can assist in their development planning

May 1, 2002

By C. A. Sutherland

"Smelting of copper-gold ore from nearby Rossland mines started at Trail in the 1890s. As ore from the Rossland mines became exhausted, lead smelting of hand-sorted galena ore from other British Columbia mines was initiated. With the development of flotation technology for the separation of lead, zinc, and iron sulphides in the first two decades of this century, the large Sullivan orebody at Kimberley, British Columbia, became the f oundation for the growth of a major zinc and lead smelter at Trail. Lead smelting began in 1901, electrolytic zinc in 1916, and by 1984, the Trail metallurgical complex had produced 10 million tons of each metal. Its present capacity is 270000 tonnes per year of zinc and 110 000 tonnes/year of lead.This paper reviews the history of technological changes in the Trail production plants, emphasizing the zinc plant modernization program started in the 1970s, and also the planned introduction of the QSL oxygen lead smelting process in the late 1980s. Lead modernization will increase production capacity to a maximum of 160000 tonnes per year.IntroductionCopper-gold ore was discovered at Rossland, British Columbia, in the year 1890, starting a mining industry that was to last over three decade s. Selected ore was at first transported at high cost to distant U.S. smelters, so there naturally followed a decision to construct a small copper smelter to process the local ore to matte. It was built in 1896 at the mouth of Trail Creek on the Columbia River, about 10 km from Rossland. This little smelter was to develop and diversify in the next 90 years into the world &apos;s largest lead-zinc producer).The mining boom that occurred in the northwestern United States and southeastern British Columbia in the period of 1890 to 1910 saw the brief operation of many small local smelters. The only one to survive was the smelter at Trail. The circumstances that permitted its continued life and subsequent growth, form a fascinating history of business deals, litigation, andsteady technical progress.Early investment in local railway transportation and options by F.A. Heinze, the smelter&apos; s founder, attracted the attention of the Canadian Pacific Railway Company, which purchased Heinze&apos; s assets in 1898. This provided the capital base for survival and growth of the smelter, which remained and prospered under the Canadian Pacific umbrella for almost ninety years. It was registered as the Consolidated Mining and Smelting Company of Canada Limited in 1906; in 1966, this name wasshortened to Cominco Ltd.The Rossland mines continued to supply copper ore for the smelter until the late 1920s, but lead-silver ore also became available from the contemporary mining boom in the Slocan area, about 80 km away. In 1901, the Trail smelter diversified into lead; and when the CM&S Co. acquired the St. Eugene Mine at Moyie and the Sullivan Mine at Kimberley, the smelter was guaranteed a firm supply of lead ore. The company also purchased the West Kootenay Power and Light Company, which even before the turn of the century had constructed the first of four hydroelectric generating plants on the Kootenay River near Trail. This acquisition assured the CM&S smelter and its local mines of a stable power supply and the opportunity to diversify into power intensive technology."

Jan 1, 1988

By Michel Gamache

This paper describes a system that manages and assigns vehicles in real-time in an underground mine. Each dispatching decision takes into account the traffic on the road segments of the mine network, whether bi-directional or unidirectional, and ensures that each LHD (Load-Haul-Dump Vehicle) arrives in the right orientation at loading and dumping points. Such systems can be used for two main purposes: 1) as a strategic planning tool and 2) as a real-time managing and optimising system for operations. Using a simulator in conjunction with the fleet management system, it is possible to accurately estimate the impact on productivity of decisions such as the development of waiting areas (bays, sidings), or the addition (elimination) of vehicles to the fleet in operation. Moreover, when used in for real-time dispatching, routing and scheduling of vehicles, the system can optimise production with respect to various assignment criteria such as minimising the cycle time or minimising the deviation from an optimal production plan. Dispatching, routing, and scheduling are handled simultaneously, taking into account the mine status, operational constraints, and all available information.

May 1, 2001