Search Documents

By D. F. Coates

Slope problems arise on mining properties from cuts for roads and railroads and from open pits. When it is 'realized that 1,000,000 extra tons of waste may have to be mined as a result of an average slope being reduced by 1 ° it is easy to appreciate that the slope problems connected with open pits are of far greater importance than the others. The type of slope failure that can occur can be classified in different ways. The most useful classification would be one that separates the causes in such a way as to provide a basis for studies to deal with problems of prevention and control. Using this criterion the types of slope failures are classified into four groups. Having classified the problems in this way an understanding can be gained of the various mechanisms involved in failure ..

Jan 1, 1961

By W. R. Green, B. W. Barde

"Geological exploration involves the collection and analysis of a wide variety of information. A basic problem in interpretation is to determine the interrelationship s of the different data. A number of statistical methods can be applied to this problem, provided that subsets of data can be selected.We have recently developed a set of interactive computer programs which provide the cap ability to quickly examine a large set of data, and may be used by people with little previous computer experience. There are two main stages in using this system. First is selection of subsets of data , by applying various tests on the values of given items. This includes matching specific entries in descriptive fields, and minimum - maximum tests on numeric fields. The second stage is basic statistical analysis and data display , including histograms, 2-D scalier plots, probability (cumulative frequency) plots, and correlation matrices. All output can be viewed on a computer terminal, and important parameters changed to produce the most effective display for use in interpretation.This system has been applied to a number of different exploration problems. An example was the determination of the nature and extent of mineralization of a gold prospect in the Queen Charlotte Islands, from drill-hole data. With the aid of the computer programs , a mineralized zone was defined, and locations for further exploration identified."

Jan 1, 1984

By J. -F. Blais, M. -O. Simonnot, J. Mocellin, G. Mercier, J. -L. Morel

Large quantities of ferromanganese sludge are generated as waste material by blast furnace during the manufacturing of ferromanganese. These slags are very rich in manganese, zinc and lead (5 to 40 %). These residues have been deposited in a pond in periphery of the steel industry. Considering the market value of the metals, these brownfield sites can now be considered as secondary resources. We have developed a hydrometallurgical process for selectively leaching Zn, Mn and Pb in order to produce compounds of Mn and Zn pure enough to be economically recoverable and a residue rich in Pb. Batch laboratory experiments were carried out to determine appropriate leaching conditions to maximize zinc extraction (100 %) and manganese extraction (90.0 %) with sulfuric acid and to generate a residue containing 15 to 30% of lead. This Pb residue is recyclable by another process.

Jan 1, 2015

By W. F. Scott, K. L. Somerville

"This paper outlines the development and inplementation of functional training at the Thompson Mine of Inco Metals Company, Manitoba Division. This training is an extension of similar methods implemented throughout the company to meet safety and health and productivity objectives. It consists of the orientation to the mine, induction in the basic mining skills, and specific training in drilling and other skills in the mine. Initial results indicated a positive effect on the safety performance and proficiency of the mine workforce.IntroductionThe primary mining method at the Thompson Mine is mechanized cut and fill, with secondary recovery of pillars by undercut and fill . These methods require a workforce of about 900 hourly operating employees to obtain capacity production of 6500 tons of ore per day.Historically, turnover of mine employees has been high and large numbers of new recruits are introduced to the mine every year. These men are recruited primarily in Manitoba, but also from distant areas of Canada; most of the se people have no previous mining experience.Training has always been an important component of mine operations. Mine supervisors and experienced miners have committed an appreciable amount of time and effort to training these new recruits. As well, training efforts have been directed toward upgrading the skills of experienced workers.Recently, a growing awareness of the significance of this training effort and its impact on accident frequency, productivity, turnover and other important parameters of the mine operation has led to a review of training methods. The training program described in this paper has resulted from this review."

Jan 1, 1981

By O'Halloran. Gerard F.

"ECSTALL MINING has installed in their plants the most modern equipment in the mining industry. At the minesite, digital blocked frequency controls are used to monitor all crushers, conveyors, ventilation equipment and pumps from underground. Distant pumping stations are monitored and controlled by radio. Modern friction skip and cage hoisting systems have been installed with static power supply designed for automatic operation. Rotary-type compressors of recent design are in service in place of the conventional reciprocating-type units. At the concentrator, the 800- and 1500-hp synchronous motors driving the grinding mills have static field excitation and pneumatic clutches, still meeting modern-day concepts, having been• installed in 1966. The maintenance work load has increased annually for the past eight years. The modern plant, with all the present-day sophistication, must have a welltrained and well-organized force of skilled workers, and a maintenance system which will supply realistic facts and guidelines. This presentation will review the relative location of plants, utilities, maintenance and services, plant maintenance control and mechanical control. It is the hope that enough information will be presented to weigh the size of the job and how the resources are utilized for controlled maintenance."

Jan 1, 1974

By Q. Shi, Q. Feng

"The influence mechanism of chlorite on the flotation of pyrrhotite was investigated through flotation tests, Zeta potential measurements, optical microscope photos, solution ion measurements and absorption measurements. It is observed that, the addition of chlorite influences the flotation of pyrrhotite seriously. The IEP (isoelectric point) of pyrrhotite and chlorite is 7.6 and 4.3 respectively, in the condition of slight alkalinity, both pyrrhotite and chlorite are negatively charged, and the hetero-aggregation will not occur. With the existence of oxygen in solution, the iron ions are dissolved from pyrrhotite surface because of the oxidation of pyrrhotite during pulp conditioning. The dissolved iron ions adsorb onto the surface of chlorite in the forms of iron hydroxyl and iron hydroxide, and the adsorption results in the opposite charge of chlorite surface. As a result, the hetero-aggregation between pyrrhotite and chlorite occurs. The adsorption of chlorite changes the surface property of pyrrhotite and restricts the adsorption of amyl xanthate onto pyrrhotite surface, and then decreases the flotability of pyrrhotite.INTRODUCTIONIn sulfide ores processing, magnesium silicate bearing gangue minerals often report to the concentrate causing downstream processing problems as well as increased smelting costs. Talc,chlorite and serpentine are gangue minerals commonly encountered in complex sulfide ores (Engel, Middlebrook, & Jameson, 1997; Pietrobon et al., 1997; Witney & Yan, 1997; Chen, Grano, Sobieraj, & Ralston, 1999a, 1999b; Bremmell, Fornasiero & Ralston, 2005; Senior & Thomas, 2005; Wang, Somasundaran, & Nagaraj, 2005; WieseHarris & Bradshaw, 2007). All of them are characterized with uniform crystal structures consisting of silicon-oxygen tetrahedron and magnesium-oxygen octahedron. The magnesium-oxygen octahedron layers are broken during the liberation of serpentine to expose the magnesium-oxygen bonds with strong ionicity and hydration, which results in natural hydrophilicity of serpentine. In water, the hydroxyl on serpentine surface ruptures and dissolves into the aqueous phase while the Mg2+ remains, resulting in surface positive charge (Tao, 2012). As serpentine has a positive potential at alkaline condition, it is therefore likely that it will attach through electrostatic attraction to the negatively charged mineral surface and reduce both the flotation rate and recovery of target minerals (Lu et al., 2011). For talc, characterized as good natural hydrophobicity, the liberation comes from the interlaminar fracture to remain molecular bonds on surface with weak hydration. Being naturally hydrophobic, talc easily reports to flotation concentrates, thus reducing concentrate grade (Shortridge, Harris, Bradshaw, & Koopal, 2000; Beattie, Huynh, Kaggwa, & Ralston, 2006). Meanwhile, both molecular bonds and magnesium-oxygen bonds are exposed on chlorite surface when liberation occurs, resulting in moderate natural hydrophobicity between serpentine and talc (Tao, 2012). And thus the mechanisms of influence of chlorite on sulfide ores are more difficult to study."

Jan 1, 2016

By Richard Simon

This paper presents an ongoing study on the use of borehole breakouts to estimate in situ stresses at depth in a Canadian underground mine. Breakouts were identified using an acoustic televiewer (ATV) probe. Rock samples were tested in a laboratory to determine their failure curve. Breakout analyses were performed using a 2D failure criterion and a multiaxial failure criterion. Analyses were carried out using both short-term (peak) and long-term strengths (the latter considered here as being represented by the damage initiation threshold DIT). The analyses have shown that the use of the longterm strength and a multiaxial failure criterion leads to results that are more consistent with stress measurements performed in the field, in the vicinity of the mine.

Jun 1, 2012

By P. A. Crane, N. Shirley, Aung Moe, H. M. Nicholson, D. Kan

Kazakhstan’s first commercial copper-leach solvent extraction-electrowinning plant, Central Asia Metals’ Kounrad project, was commissioned in April 2012. Exploiting low grade waste stockpiles produced during Soviet era open pit mining, a 10,000 tpa copper cathode plant was designed, constructed and commissioned within 18 months. Overcoming initial challenges with a workforce unfamiliar with the technology and with extensive periods of sub-zero conditions during winter the project has consistently met targets and produced high quality copper cathodes at cash costs of less than US$1/lb. Challenges encountered during the first two years of operation are described and future plans briefly discussed.

Jan 1, 2014

By L. P. Srivastava

Rock bolts have been used since long to enhance the shear strength response of jointed rocks in civil and mining engineering structures. However, the assessment of strength response of a rock mass reinforced with rock bolts remains an unresolved problem till date. In the present article, an attempt has been made to study, through physical model tests, the shear strength enhancement of a blocky mass due to provision of passive rock bolts. Direct shear tests were conducted on large specimens of size 750 mm x 750 mm x 900 mm of rock mass under a normal stress varying from 0 to 2.0 MPa. Concrete was used as a model material to simulate intact rock and, elemental blocks of size 150 mm x 150 mm x 150 mm were used to form the mass specimens. Steel bolts of 6 mm diameter with 2 mm thick grout were used to reinforce the mass. Three different configurations of bolts were adopted. Observations were made on shear stress, horizontal shear displacement, and dilation during the tests. Effect of normal stress and reinforcement on peak shear stress and shear stiffness was studied. It is observed that the rock bolts enhance the shear strength of the mass by preventing sliding along the shearing plane, and by inducing additional normal stress due to tension mobilized in the bolts. The rock mass, therefore, becomes stronger due to the high degree of interlocking produced by the bolts. Shear strength of the mass increases with increasing numbers of bolts. In the case of reinforced mass, the enhancement in shear strength due to provision of bolts decreases with an increase in normal stress. The provision of bolts improves the cohesion of joints substantially. The effect on friction angle is low. The shear strength enhancement depends on the area of the bolts, spacing of the joints, spacing between the bolts and the cohesion of the intact material. A correlation has been established using which the enhancement in shear strength due to the provision of bolts can be assessed.

Jan 1, 2015

By Alexandre Desbarats, Michel David

"All optimum pit design studies start from the geological are reserves inventory, the estimated grades of all blocks of potential are within the interpreted limits of the deposit. The actual optimization procedure is then carried out on block valuations based on these estimated grades. Thus, the relevance of any pit design can be seen to depend directly on the ore reserve estimation . To insure a proper pit design, a first step would be to use a geostatistical reserve estimation technique such as kriging, however, this is not enough. A frequently neglected fact is that the blocks of ore estimated during the planning stage of the mine are usually considerably larger than those on which the ore-waste selection will be made at the time of mining. Experience in the exploitation of large low-grade deposits has shown that large blocks, estimated to be are, when mined selectively in smaller blocks, often yield significant amounts of waste material. This phenomenon, known as internal waste, is a function of the variability of the grades, the size of mining unit and the amount of sampling information on which ore-waste decisions are made.In this study, it was proposed to consider the effect of internal waste caused by selective mining, on. pit design, using geostatistical methods to predict the tonnage and grade of recoverable reserves within large blocks.Optimum pits obtained using a block valuation formula taking into account the recoverable reserves within large blocks were compared with optimum pits obtained using a conventional block valuation formula. It was found that the optimum pits obtained by the proposed method had the highest total valuations and thus were, in fact, ""more optimum”. These pits were characterized by greater are tonnages at a lower average grade, the additional ore more than compensating for the drop in grade. It was also found that the consideration of internal waste in pit design could considerably alter pit limits in marginal areas of the deposit.It was concluded that selective mining had a significant, potentially critical, impact on the design of optimum pits especially in the case of large low-grade deposits."

Jan 1, 1984

By W. P. Tassie

"The location of Quintette Coal Limited's pit and geologic nature of the dedicated reserves combine to introduce a number of factors which can adversely affect waste dump stability. These factors include steep terrain, variable material type and particle size, and precipitation. This paper describes the solutions to related waste dump problems. A brief geotechnical review of the waste dumps is given and Quintette's operational strategies during periods of dump stability and instability are discussed. Despite best efforts, failures occasionally occur and discussion is included on Quintette's success at bringing failed dumps safely back into use. IntroductionQuintette Coal Limited (QCL) property is situated on the east slope of the Rocky Mountains near Tumbler Ridge, approximately 120 km southwest of Dawson Creek, British Columbia. This surface mine is located on mountainous terrain and is subject to climatic extremes of wind, precipitation and temperature.QCL has a current annual production of 4.75 million tonnes of metallurgical coal with a stripping ratio of 7: 1. This correctly implies the extraction of over 33 million bank cubic metres (BCM) of waste which is placed on numerous waste dumps at various locations adjacent to the pit.There are three active pits - Mesa, Wolverine, and Shikano (Fig. 1). Shikano is a newly developed pit located near the plant site. It is not subject to the unique dump management problems prevalent at the Mesa and Wolverine pits, therefore the Shikano waste dumps will not be discussed . The dumps for the Mesa and Wolverine pits, however, have been technically and operationally challenging since shortly after mining began in 1983. Their characteristics, associated site specifics and management, therefore, are the subject of this paper.Waste dump locations for the Mesa and Wolverine pits are shown in Figures 2 and 3 as is the relative waste distribution . Each sub-pit is connected to a principal waste dump in reasonable proximity and to an alternate dump should disposal of waste be necessary at that location. The waste dumps are constructed from the top elevations initially to coincide with subpit development. In the initial years (1-7) waste dump heights will be up to 250 m, then, as the mine matures (8-20 years), waste dump maximum heights will continuously decrease to coincide with lower bench elevations"

Jan 1, 1988

By Kwang-Hyun Jeon

Recently, 3D printing technology in the manufacturing field is in the spotlight. In the construction industry, similar rapid prototyping technology that does not use conventional form can be applied to meet the demand on free formed structure that can provide aesthetic value and functionality. Conventional formwork can increase construction cost and period for various structure with complex shapes while it has numerous advantages such as high strength, convenience, accuracy and good quality of surface roughness. To meet the demand on free formed structure, automated freeform construction systems such as Contour Crafting and Concrete Printing have been developed with active collaboration between university and industry in USA and England. However, details on the system have not been fully released in public, so the possibility of its fusion and spin-off technology cannot be expected. In this paper, cost-effective solution for mechanical and control system for constructing a free curved structure without mold are described. As an appropriate material for the system, fiber reinforced mortar was selected by experiments on compressive strength, setting time and fluidity. After performing G-code simulation, transfer and extrusion experiments with the selected mortar mix were performed and the possibility of the development of automated freeform construction system was demonstrated. Based on this research results, it is required to keep the automated freeform construction system improve and extend it into the new application area in construction industry.

Aug 1, 2013

By F. A. McLean

Given a promising claim and the required financial backing to develop it, the first problem that confronts the mine operator is usually the selection of the necessary compressed air plant. The size and type of drive are questions that naturally follow, the former being determined largely by the amount of money available and the speed with which it is desired to carry on the programme of development. The type of drive, such as electric motor, steam or oil-engine, depends on local conditions and has an important bearing on the cost of operations. ns. Few prospective mine operators are fortunate enough to locate claims within the service radius of electric power-lines, although this is more likely to happen nowadays than formerly. In the majority of cases, however, some other form of prime mover is necessary. When wood or coal are available at moderate cost, a small steam-driven plant is usually chosen. Such plants are often arranged so that they can be converted to electric-drive should future developments at any time make this desirable. Many plants of this type are installed in northern Ontario mines. When wood or coal are costly or difficult to transport, oil-engine driven mining plants have many advantages in their favor, and are now quite commonly used. Oil in some locali-ties is considerably cheaper than wood or coal, and is much easier to transport over bad roads.

Jan 1, 1924

By E. Ghali, C. Su, G. Houlachi

"The influence of lead ions on zinc electrowinning process was investigated by means of electrochemical noise measurements (ENMs) and cyclic voltammetry in conjunction with scanning electron microscopy and X-ray diffraction. All electrochemical experiments were performed in sulphuric acid electrolyte containing different lead ion concentrations as impurity. Lead was added in six trace levels between 0.05–0.8 mg/L in the bath. The lead content of the zinc deposits was dependent on the introduced lead concentrations. The overpotential associated with zinc electrodeposition shifted to higher values with the increase of lead concentration in the solution. An appropriate correlation was found between the different concentrations of lead in the electrolyte and the morphology of zinc deposit by ENM. The results showed that the increase of lead ion concentrations is generally accompanied with the decrease of skew and increase of kurtosis values that could be related to the morphology of zinc deposit. Effectively, the morphology changes from well-defined hexagonal platelets to large hexagonal, layered platelets and finally to non-symmetric refined crystalline structure, respectively.INTRODUCTION In commercial zinc electrowinning, zinc oxide is leached from the roasted calcine with an aqueous acid sulfate electrolyte. Then the zinc-rich solution is purified and transferred into an electrolytic cell. During electrolysis, zinc is deposited on aluminum cathode where lead-silver or pure lead is served as anode. Electrodeposition of zinc could be influenced by several parameters such as bath acidity, temperature, current density, the nature and concentration of impurities as well as additives in electrolyte. Metallic impurities play a complex role during zinc electrowinning and they can adversely"

Jan 1, 2016

By Serena Biella

Gold has received a growing interest as a catalyst for the selective oxidation of organic molecules using oxygen under mild conditions1. In the liquid phase application small gold particles (2.5-7 nm) deposited over different solid supports can be used but, like many other noble metals, their catalytic activity depends upon the nature of the support and the preparation metod2-5. In particular, gold on carbon is the preferred catalyst for the oxidation of the alcoholic 2-7 and the aldehydic7-9 groups and one of the best preparation method is the immobilisation of colloidal particles2-5,8,9. Suggested application of gold catalysis in fine chemicals production, tested on laboratory scale preparations, is reported in table 110. In order to produce more efficient catalysts for the liquid phase oxidation and to derive new insights into the reaction mechanism, we have made a comparison among catalytic systems based on different metals. The first effort was to test the activity, if present, of naked metal particles and then to study the influence of various materials commonly used as a support.

Oct 1, 2003

By Terry McNulty

"Previous papers (McNulty 1998 and 2004) have dealt with the causes of successful and less successful achievement of design production rate by new processing plants in the minerals industry. Examination of many case histories has allowed the construction of curves or profiles that represent projects with similar characteristics that equate to differing degrees of care exercised during the project development phase. Simplistically, decreasing care is reflected by increasing risk and a heightened likelihood of poor technical and/or financial performance.This contribution provides an update, including recent case histories, and presents a modified Series 1A curve that includes the best 23 case histories, out of a total of 81 examined, or 28%. This is done to show that some very carefully developed and executed projects can ramp-up quickly and that owners of new projects should avoid being too pessimistic in projecting early cash flow if they are certain that they have done their homework. The role of metallurgical process development in the reduction of project risk is discussed and several financial analyses are presented that express the potential monetary value of a well-designed and professionally executed metallurgical program."

Jan 1, 2014

By C. Karpuz, Y. S. Istanbulluoglu

This paper describes the results of convergence measurements conducted about five years for the re-use gate roadways at OAL lignite mine in Turkey. Double lignite seams separated with a marn layer, are mined with long-wall retreating mining system at the mine. Rib pillar has been abandoned and gate roadways were planned to be packed for the re-use of full extraction. Various packing systems have been attempted, namely three rows of woodenchock, one row of wooden chock plus concrete wall and concrete wall only. The re-use of maingate roadways packed with wooden chock yielded 62% of closure. Lastly developed concrete packing of 3 meters wide and specially developed support set composed of three friction props and a cap, which is a modification of yieldable set, have successfully maintained the main and tail gate roadways stability with a total vertical convergence of 32%. Good correlation has been established between pack stiffness and floor heave as well as maingate and tailgate convergences. The elimination of rib pillars by re-use of gate roadways increased the coal recovery by 20% and decreased the development/production ratio from 0.065 m3/ton to0.022 m3/ton.

Jan 1, 1997

By Botao Lin, Yan Jin, Hongjuan You, Jingjun Pan, Huiwen Pang, Mian Chen, Sen Chen

"Steam Assisted Gravity Drainage (SAGD) has become the mainstream technology for ultra-heavy oil recovery in Xinjiang oilfield, the success of which depends heavily on shortening of preheating period as well as forming homogeneous and highly permeable zone in land-facies oilsands layer. Towards this aim a special hydraulic fracturing process is required, which is accomplished through controlled water injection to a pair of horizontal wells in order to create homogenously distributed microcracks in the zone between the two wells. The associated mechanical response, however, is unclear for land-facies Karamay oilsands that is loose in texture. In this regard, this research utilizes a triaxial test system on cylindrical specimens extracted from field-collected oilsands cores. Isotropically consolidated drained triaxial compression tests are conducted on both saturated and unsaturated specimens so as to investigate the mechanical response of oilsands at different spots relative to the wellbore. Moreover, acoustic emission and fast pulse-decay permeability are performed to monitor fracture development and permeability evolution. Based on these experimental studies, the mechanism of dilation in oilsands is comprehensively analyzed. The findings reveal distinctive behavior between the saturated and unsaturated specimens as respect to dilation, porosity/volumetric evolution and change of permeability. It is also found that shear bands can be created upon shearing on triaxial specimens, rendering porosity or volumetric strain the factor that is more proper for evaluation of stimulation efficiency in the field.INTRODUCTIONXinjiang oilfield is widely known for its abundant deposit of heavy and ultra-heavy oil that has been estimated to be several hundred million tons. The ultra-heavy oil deposit located in Fengcheng region of Karamay at the northwestern part of the Junggar Basin, Xinjiang, China, has over 360 million tons of resource (Yuan et al. 2013). The resource is deposited in depths from 180 to 450 m and has viscosity over 100, 000 mPa•s at a temperature of 50ºC, bringing technical challenges to recovery activities."

Jan 1, 2015

By Joseph Sawicz

By now, the concept of remotely controlling heavy equipment in underground mines has become commonplace. Personnel safety is the biggest justifier for remote control, followed by an inherent cost saving (in certain cases) when wireless video is added to the mix. There are a handful of vendors targeting this need, and for years the mines have remained loyal to their brand. But as the number of remote-control related accidents and maintenance costs increase it forces our industry to take another look at this commonplace concept. And as the blinders are taken off, the mines are getting the revelation that not all remote control systems were created equally. This paper highlights the differences between various remote control systems, and then moves into an in-depth look at HARD-LINE?s package which drastically cuts maintenance costs, and also provides a solid investment toward full Tele-operation.

Apr 1, 2005

By I. Murray, N. Geoffroy

"Buried pipelines, tanks and other similar equipment are almost always present on large scale industrial sites, including in the oil and gas fields. However, as the proverb “out of sight, out of mind” suggests, it is easy to overlook proper maintenance procedures and simply assume that corrosion protection measures in place are working correctly. Unfortunately, this is not always the case, leading to significant environmental damage and loss of production. This paper describes several cases from various industries where buried equipment failed because of corrosion, sometimes with catastrophic results. It also presents various strategies, based on experience and new research, to help predict and prevent damage to underground metallic structures.INTRODUCTION Metallic underground structures are extremely common in industrial and commercial settings for numerous reasons. Burying pipes, tanks, wires and other similar equipment has numerous advantages: it provides significant protection from mechanical damage, frees up ground space that can be used for other purposes, requires little to no support structure and is generally more esthetically pleasing. However, this last benefit can also be considered the most significant disadvantage of underground equipment: becoming invisible and forgotten. While every engineer is aware of the importance of preventive maintenance, it is also human nature to somewhat forget about equipment that is hard to inspect and assume that everything is fine. This is unfortunately not always the case and failures in industrial settings can have extremely serious consequences. While economic aspects immediately come to mind (loss of production, cleanup cost, etc.), failure of underground equipment also results in an environmental and therefore public relations nightmare, especially in the oil and gas field. Leaks that would have been considered negligible in the past can now make national headlines and perfect reliability, while probably impossible to achieve, is now the goal of most companies. While environmental damage (real or perceived) is most often associated with leaks in the oil and gas industry, it can also affect the mining world. For example, the authors have worked on a project where a buried slurry pipeline had ruptured in the ground, causing a release of perfectly inert tailings. While the economic loss was low, the leak was reported in local media and caused a public relations problem."

Jan 1, 2017