Search Documents

By S. Sillitoe

In mining, as in other business and engineering enterprises, efficient operation depends upon how well and how quickly the lines of communication can function. Mines have used the telephone on and between levels for many years, but in the hoisting shaft maintenance of physical wire connections for communication with the moving cage or skip has been found, for all practical purposes, impossible. A most natural solution was, therefore, the code-bell or buzzer signal system between fixed levels, and this has been standard practice throughout the mining world for many years. However, this system has serious limitations which make it impossible to signal a cage between levels in the shaft, and it requires crude, hazardous or costly methods for signalling during daily shaft inspection. Radio signalling overcomes these difficulties, because the communication medium is never broken and the cage-tender or shaft inspector can safely signal to, and receive signals from, the hoistman at any time from any position in the shaft, whether stationary or in motion. In addition to both audible and visual code signalling, two-way telephone communication and slack cable alarm are facilities made possible in recent commercially developed equipment.

Jan 1, 1949

By R. A. L. Drew, F. Edelmann

Brazing is a low-cost process used extensively in the manufacturing and repair of aircraft gas turbine engines. Components within the compressor stage of the engine experience relatively low temperatures (600-700°C), therefore joints of stainless steels are typically employed. In such joints, a Pd-Ni-Cr-Si-B (PalNiCroTM) brazing alloy is used as a sealant, however brazing procedures are not well understood. The wetting behavior of PalNiCroTM on AISI 347 was evaluated with respect to contact angle. A microstructural evaluation was carried out with variable joint clearances. Microhardness profiles were performed to investigate the presence of hard secondary phases, which were later confirmed by electron microscopy. The results indicated an equilibrium contact angle of 10° within 100 seconds. The average microhardness of the braze layer and base metal were approximately 550 and 205 VHN, respectively. At the interface, a diffusion zone was present containing carbides and borides.

Jan 1, 2004

By Ken G. Kress

Syphons can be a simple, reliable and proven alternative to otherwise more complex pumping systems or low level outlet works. In a simple form they consist of a pipeline constructed over the top of an embankment or high topographic feature, connecting a source pond to a receiving pond or channel (see Photograph 1). The syphon action is initiated by removing air from the pipeline (priming) using simple devices which can be purchased ?off the shelf?. Once primed, the syphon flow rate can be controlled or stopped using conventional gate, valve, orifice plate or other devices. Repriming is not required even if the flow is stopped, provided the syphon is not drained. A limiting factor in considering a syphon as a design option is the maximum lift (i.e., vertical distance from source pond level to summit of syphon) which is approximately 9 metres, or less, dependent on syphon pipe features and site conditions. Pipeline syphons can be quickly constructed from readily available materials including steel, polyethylene and PVC pipe. They are particularly well suited to many of the unique conditions often encountered at minesites. This paper identifies situations that can sometimes be best resolved using pipeline syphons. It provides basic principles for pipeline syphon design and includes case histories of their successful application.

May 1, 2001

By A. L. Mackie

Mine water from base metal mines is generally characterized as having high concentrations of heavy metals and low pH, resulting in the need for treatment prior to discharge to receiving waters. In this study, two high-rate clarification processes were evaluated at bench-scale: the high density sludge (HDS) process and sand-ballasted flocculation. High-rate clarification processes generate larger, denser flocs which settle more quickly than those formed in conventional flocculation processes. The HDS process uses recirculated sludge in order to seed floc formation, whereas ballasted flocculation uses microsand. Both of these high-rate processes require the addition of quicklime or hydrated lime to increase pH and allow for the formation of insoluble metal hydroxides, which can then be removed in the clarification stage. Previous research has shown that cement kiln dust (CKD) can effectively replace quicklime in conventional sedimentation processes for metals and acidity reduction to meet discharge guidelines (Mackie & Walsh 2012). CKD is an alkaline by-product of cement manufacture that has fine particle sizes and varying free lime concentrations depending on the manufacturing process. The lower solubility (i.e., free lime content) of CKD requires larger doses of material to be added to reach treatment pH targets for metals precipitation. The purpose of this study was to evaluate the treatment efficacy of high-rate clarification processes for mine water treatment, compared with conventional sedimentation, at bench-scale with conventional (i.e., lime) and novel (i.e., CKD) pH adjustment additives. Results of the study showed that all treatment processes (i.e., HDS, ballasted flocculation, and conventional sedimentation) were able to reduce target metal concentrations to well below Canadian guidelines (i.e., total zinc and total nickel < 0.5 mg/L, total copper < 0.3 mg/L) using either CKD or lime. Additionally, mine water samples treated with CKD generated lower sludge volumes than those treated with lime (i.e., 50 versus 100 mL for conventional sedimentation and 100 versus 200 mL for HDS) even with increased concentrations of solids introduced during treatment. This is most likely due to slower neutralization rates when using CKD, due to its lower solubility, as well as finer particle size. The sand-ballasted flocculation process was able to reduce final turbidity in CKD-treated samples while the HDS process did not when compared to conventional sedimentation, making the ballasted flocculation process preferable for reducing final solids concentrations in CKD-treated mine water.

Aug 1, 2013

By J. L. Thornton

Introduction The importance of coal in our economy is well established, but it may not .be so generally realized how important a part it plays in our daily life. Select a product - any product - and, if it is made in America, bituminous coal has touched it first. Everywhere we will find coal, derivatives of coal, or functions made possible by coal. Apart from the well known major uses of coal for domestic purposes, coking, utilities, railways, and manufacture of steel and cement, there are over 200,000 products derived from coal, from lipstick colours to nylon products and perfumes. An item of interest is the recent action of the Canadian Government in voting $90,000 for development of coal deposits in Yukon Territory to make coal available to the settlers in that area. The value of this move, in case of some emergency, is very evident. Coal in its several stages of formation as peat, lignite, sub-bituminous, bituminous, semi-bituminous, semi-anthracite, and anthracite, has been used for centuries. Coal, as such, was not very well known to the ancients. First reference to "magic stone&apos;, or coal, was in 371 BC by Theophrastus, a pupil of Aristotle. This substance was said to burn like wood coal or charcoal and was used by the smiths. The first record we have in modern times was in 852 AD, when sea coal was gathered by the cowled monks of Durham, in Britain, and even at that time a major problem was transportation. Our first record of coal in this continent was near Richmond, Virginia, in 1700. Commercial mining was not under way, however, until 1750. The anthracite fields (presumably in Pennsylvania) were opened in 1793. Even so, there was no extensive mining until about the year 1820. The famous Pocahontas coalfields were opened in 1883. The earliest record of coal mining in Canada is about 1746.

Jan 1, 1950

By John Knox

The object of this paper is to present an analysis of the major problems encountered both in the design and application of downhole drills. Particular reference is made to design features governed by: physical size limitations; metallurgical material standards; physical operating environment; range of commercial materials to be drilled; high power output required, coupled with simplicity from the operating and maintenance viewpoint; and bit design. The history of attempts to develop downhole drills is discussed, and representative mechanical configurations are illustrated. The general design and application aspects of the different types are commented on. The application of this drill type in various commercial fields, such as (a) oil-well drilling, (b) open-pit mining and (c) underground mining, is discussed, along with the limitations presently imposed by the commercial state of the art in the manufacture of accessory equipment; e.g., drill rods, air compressors, mountings, etc. Suggestions on the possible future direction of the development and application of this tool are put forth.

Jan 1, 1965

By F. Flores

With the World Summit for Sustainable Development planned for 2002 in mind, nine of the world&apos;s largest mining companies decided to initiate a project to examine the role of the minerals sector in contributing to sustainable development, and how that contribution could be increased ? the Mining, Minerals and Sustainable Development Project (MMSD). This project assumed from the start that sustainable development could provide a useful framework to guide the minerals sector which main goal was integrating economic activity with environmental integrity, social concerns, and effective governance systems. The broad steps of MMSD project strategy can be grouped into four major categories: increase understanding of sustainable development; create organizational-level policies and management systems for implementing the principles of sustainable development; collaborate with others with common interests to take joint steps towards sustainable development, and; increase our ability to work towards sustainable development at the local, national, and global levels. In opinion of the article&apos;s author, to go ahead with the MMSD strategy and achieving the sustainable development objectives, it is necessary to consider the concept of self-organization, fundamental of the emergent new scientific paradigm, and the consequent epistemology and values that conform a supporting culture for sustainable development.

Jan 1, 2007

By L H. Warren

The types of equipment available for generating a plasma have been reviewed. The efficiency and potential of the plasma generating equipment used in performing extractive metallurgical reactions have been determined. A general classification of the reactions that might be per-formed in a plasma has been proposed. Experimental work done on extractive metallurgical plasma reactions, heat transfer between the plasma and solids, and the quench of the products of plasma reaction has been summarized. From the preliminary results it appears that the high-intensity are or the transpiration-cooled anode plasma torch offer the most promising areas for further research. C ONSIDERABLE world-wide research effort is currently being devoted to the development of processing technologies which employ the new high-temperature generating devices that have appeared over the past few years. The plasma flames produced by these devices offer the potential for subjecting materials to any single gas or mixture of gases at temperatures up to 20,000°K. With these conditions available, many reactions in extractive metallurgy,

Jan 1, 1965

By D. C. Martin, P. M. Hawley, C. P. Acott

"In bedded deposits such as coal or sedimentary iron, economic limits of mineable reserves are clearly defined by the footwall of the seams or ore-bearing units. Where open pits are developed in dipping strata, a long, high footwall slope may result. In many cases, unbenched slopes excavated along the base of the lowest mineable seam are operationally simple, economically desirable and geotechnicalty practical, although a variety of failure mechanisms may develop. This paper examines the engineering geology and rock mechanics parameters of importance in the design of footwall slopes. Possible failure mechanisms and stability analysis methods are described. Design considerations for benched and unbenched slopes are discussed with prime consideration given to development of long high stopes without benches or with a minimum number of benches. IntroductionIn bedded deposits, the ultimate depth and economic viability of an open pit in dipping strata may be controlled by the design of the footwall slope. The stability and, hence, design of footwall slopes is strongly influenced by the engineering geology and rock mechanics parameters of the slope forming materials. A clear understanding of the structural geology, engineering geology and tectonic history of the deposit is essential to assess the behaviour of the slope. This is particularly important for long high, unbenched footwall slopes such as shown in Photo I.A rational footwall slope design requires identification and assessment of all possible slope failure mechanisms with respect to the proposed slope geometry. Stability analyses of each potential failure mechanism are used to identify the main controls on slope stability and to develop appropriate slope design criteria. The optimum slope design is based on the most economic and geotechnically practical slope geometry with due consideration of operational constraints and of the possible advantages of specific remedial measures."

Jan 1, 1986

By A. M. Salomon de Friedberg

With respect to impurities, HBM&amp;S&apos; copper smelter, located in Flin Flon, Manitoba, is in an unusual position. In addition to the usual concerns, the fact that copper and zinc production at Flin Flon is closely integrated results in the unique situation where feed to the copper smelter typically contains 7% to 8% zinc. This paper discusses the ramifications to copper smelter operations resulting from the marriage of HBM&amp;S&apos; metallurgical plants. Distributions of impurities (specifically Zn, Pb, Ni, As, Bi, Sb, and Cd) are presented and operating practices designed to reduce the impact of impurities on anode copper quality are detailed.

Jun 1, 1993

By Harry Perry

By 1980, the free world's need for economic sources of energy is expected to double. As a result, there will be a tremendous potential for all energy sources working together to supply the demand. For coal to continue its dominant role as a low-cost energy source, means must be found for it to meet the challenge of nuclear power and to overcome obstacles placed on its use by air and water pollution regulations. As the more limited reserves of gas and oil diminish, economic ways are also required for converting coal to synthetic liquid and gaseous fuels, and to chemicals, thus resulting in optimum utility of the most abundant low-cost fuel resource. The means for accomplishing these ends can only come about by a vigorous research and development program. Successful efforts by industry and government working together, both in America and abroad, will assure the continued use of coal to meet the world's energy demands. This paper discusses the emerging patterns of energy sources throughout the world and the role that research and development on coal will play in supplying future energy requirements.

Jan 1, 1967

By Jarret Thomson

An understanding of groundwater flow is essential for many aspects of mining. This is especially true for the process of shaft sinking through the sandstones of the Manitou Falls Group in the Athabasca Basin of northern Saskatchewan. Experience has shown that the hydraulic conductivities of these sandstones can be relatively high, especially in zones containing natural fractures. To develop a better understanding of the inflow potential into a shaft, a laboratory testing program was undertaken to investigate the hydraulic conductivity of fracture core samples from the Manitou Falls Group. This program involved the measurement of hydraulic conductivities under steady-state flow conditions, while cycling the effective confining pressure across a span that is representative of in-situ conditions. The change in fracture aperture was simultaneously recorded at each confining stress level. It was found that existing relationships relating aperture and flow did not accurately capture the behavior of the samples tested. The effects of fracture staining and infilling were also investigated, and were found to have a notable impact on the hydraulic conductivity.

Jun 1, 2012

By J. Duby

"A description is given of a series of tests performed to determine the comparative effects which dynamic and static straining, in compression, have on the physical strength properties of mild steel and an aluminum alloy. The dynamic deformation was imposed during the passage of single stress pulses of about 100 micro-second duration. These pulses were recorded with strain gauges mounted near both ends of the specimen. The resulting records were analysed using a simple wave theory; there from the dynamic stress-strain curves for the respective metals were deter-mined and were then compared with the static stress-strain relation. The respective hardnesses of the metals after deformation are evaluates by means of static stress-strain curves in compression. The micro-structures of the metals before and after deformation are also shown. It is observed that dynamic de-formation considerably modifies the rate of strain hardening. This modified hardening appears to be persistent. The observed differences in physical strength properties and micro-structures are discussed in the light of the accepted dislocation theory for metals."

Jan 1, 1960

By K. Winterton, Carruthers. J.

"Attempts have been made to produce hardened structures of a pseudomorphic type in various carbon and alloy steels. In order to obtain martensite with a fine distribution of cementite, an initial structure of fine lamellar or nodular pearlite is required; this may be obtained by conventional means. This is followed by partial austenitization and quenching.Two methods have been tried to induce partial austenitization:(a) A resistance (direct current) heating method involving rapid entry into the austenite field.(b) A new method, described as the ""threshold"" technique, involving homogenization of temperature just below A 1, followed by entry into the austenite field; two furnaces are required.The resulting structures have been examined for microstructures, hardness, tensile, and impact values. The tensile properties are comparable with those obtainable by conventional treatment methods. Impact values are disappointing, but this is explainable from the nature of the manifold changes occurring."

Jan 1, 1960

By Paul Grady, Martin Froehling, Curtis Mohns, Eliab Roman

"Since the idea of processing rock to unlock the valuable minerals inside was put into practice, efforts to improve production began. Methods have been learned that allow for operation in environments and under circumstances where it would not have been possible until now. All existing operations have experienced at least some form of productivity improvement measures. The objective is simple: generate more product of better quality in less time and at lower unit cost. Since the year 2000, various modifications have been made at the Kemess Concentrator in efforts to improve productivity. The following is a discussion of these modifications and their contributions to the success of the operation.INTRODUCTIONThe Kemess South Mine, a major producer of gold and copper, is located in north-central British Columbia. Kemess was brought into production in May 1998 by Royal Oak Mines with a modern mill controlled by a fully integrated Foxboro IA DCS system and employing 134 people. On February 11, 2000 Northgate Exploration Limited (now Northgate Minerals Corporation) acquired Kemess Mine from receivership. Since acquisition in 2000, Kemess has seen many accomplishments, including the reduction of costs by 40% site wide.The mill has a nameplate capacity of approximately 56,000 tonnes per day which is processed through a Metso (Svedala) 60” x 89” Primary Gyratory Crusher and then conveyed by a 60” conveyor to a stockpile with 48 hours of total storage capacity. The nominal minus 6” rock from the stockpile is fed to two parallel grinding circuits (A & B). Each section consists of a 10.4 m F x 4.7 m SAG mill with dual drive motors (4,480 kW apiece) discharging onto a 2.4 m x 7.3 m Metso (Svedala) single deck vibrating screen to remove the coarse material for recycle to the SAG mill by a Continental 45º high angle sandwich conveyor. Screen undersize is pumped along with ball mill discharge to a cyclopac consisting of twelve Krebs 66 cm F cyclones to classify flotation feed to a size of approximately 65% minus 200 mesh. Cyclone underflow feeds a Metso (Svedala) 6.8 m F x 11.0 m ball mill, also with dual drive motors (4,480 kW apiece). The primary grinding circuit has 35,840 kW available for grinding."

Jan 1, 2005

By A. M. Salomon de Friedberg

"With respect to impurities, HBM&S&apos; copper smelter, located in Flin Ron, Manitoba, is in an unusual position. In addition to the usual concerns, the fact that copper and zinc production at Flin Ron is closely integrated results in the unique situation where feed to the copper smelter typically contains 7% to 8% zinc. This paper discusses the ramifications to copper smelter operations resulting from the marriage of HBM&S&apos; metallurgical plants. Distributions of impurities (specifically Zn, Pb, Ni, As, Bi, Sb, and Cd) are presented and operating practices designed to reduce the impact of impurities on anode copper quality are detailed.IntroductionHudson Bay Mining & Smelting Co. Ltd. (HBM&s), has been operating its metallurgical complex located in Flin Flon, Manitoba, since 1930. The smelter and zinc plant were originally separate entities with respect to production. The smelting operation consisted of traditional multiple-hearth roasters, a reverberatory furnace and Peirce-Smith converters. The zinc plant also utilized multiple hearth roasters and then followed with sulphuric acid leaching, purification and electrowinning. The zinc plant also recovered cadmium from a separate purification/electrowinning circuit.The two plants operated essentially independently of each other until rising zinc levels in the copper concentrate and large stockpiles of zinc-rich leach residues prompted the construction of the fuming plant in 1949. The smelter used pulverized coal to reduce zinc oxide present in the reverb slag and then captured the resulting zinc bearing fume in the fuming plant baghouse. The fume was sent to a separate ""oxide roaster"" in the zinc plant where it was first roasted to remove halogens and then leached to recover the contained zinc. This oxide fume became a major source of feed to the zinc plant accounting for roughly one quarter of the total zinc production. Furthermore, through the smelter&apos;s treatment of sulphide leach residue, both copper and zinc recoveries were improved for the over-all complex."

Jan 1, 1993

By F. Charette

The paper reviews the requirements of the instrumentation required to monitor mining excavations in a high stress environment, and the development plan to instrument the D-Bolt in such a fashion as to be able to follow the behaviour of the bolts in relationship to the ground movements and support performance. Recent field observations of D-Bolts under static and dynamic conditions are also presented. Also discussed is the assumed mechanical behaviour of the D-Bolt. D-Bolts are used in two (2) Canadian underground mines operating in high stress environments and tested in three (3) other operations.

Jun 1, 2012

By C. J. Coulson, G. A. McKay, A. M. Cormie

"The Leitch mine, in the Beardmore area, Thunder Bay district, Ontario, is a part of the Leitch estate. It includes a group of patented claims, staked by P. A. Leitch of Port Arthur early in the century, along bands of jasper, hematite, iron-bearing slates, carbonatized schists, and greywacke, commonly known as 'iron formation'. The folding and shearing in these variably interstratified beds is a striking structural feature. The vein pattern is very definitely related to these structures.ROCKSThe rocks in the area are typical Keewatin lavas-greenstone-overlain by a series of Timiskaming sediments consisting of arkosic greywacke, iron formation, slate, greywacke, conglomerate, and greywacke, in this order from the contact. The sedimentary beds are generally conformable with the older rock contact except on local folds.Small intrusions of diorite occur as nearly vertical dykes and are believed to be of Algoman age. To the northwest of the mine there are larger intrusions of granodiorite belonging to the same period.Several dykes of quartz diabase up to 100 feet in width, striking generally north and south, with a vertical dip, cross the property. These have been classified by W. C. Laird as pre-Keweenawan in age. One of these dykes in particular is of importance for it cuts through the No. 2 vein and serves as a pillar when stoping. It is approximately 6 feet wide.The youngest rock type represented is a sheet of olivine diabase that extends over an area of thousands of square miles in and around lake Nipigon. It underlies most of this area and its outcrops form some of the most interesting topographical features, with fault scarps rising hundreds of feet. In the vicinity of the mine shaft the sheet is about 600 feet thick and extends from a depth of 1,871 feet to approximately 2,470 feet. It has a dense, hard, chilled margin and a sharp, tight contact. It intruded the sediments with very little lateral disturbance. The chief effect was baking, which darkened and hardened the greywacke near the contact. The sheet dips flatly to the cast."

Jan 1, 1954

By R. B. Fermor

"The tyndalloscope is used in Europe for dust-hazard assessments in both coal and metal mines. Dust-hazard conditions can be directly evaluated by the tyndalloscope in many underground working situations, once the basic standard table or tables have been prepared from representative mine-rock samples.The tyndalloscope is excellent, in many cases, for diagnostic dust sampling during a working shift, because individual readings can be taken to within three-minute intervals. The limitations of the tyndalloscope are also discussed.The author suggests that a combination of both the tyndalloscope and gravimetric sampling methods would be an ideal match for most mine dust-hazard assessments."

Jan 1, 1970

By L. Jiang

This report investigated the dynamic recrystallization (DRX) phenomenon in magnesium alloy AZ31 billets to understand the deformation mechanisms and microstructure evolution during extrusion and other metal forming processes, Compression tests of coarse-grained as-cast magnesium alloy billets containing lamellar Mg17Al12 eutectic phase and (Al, Mn) particles suggest that temperatures higher than 300°C, strains greater than 0,25 and strain rates above 0,l/s lead to the formation of fine DRX grains in the deformed samples. Microstructural observations also indicate particle-stimulated DRX nucleation (PSN) during hot deformation of the AZ31 alloy, facilitated by the presence of Mg17Al12 and (Al, Mn) particles, While the Mg17Al12 is dissolved into the matrix at about 350°C, (Al, Mn) particles may remain effective for PSN at temperatures up to at least 400°C, This study suggests that alloy design with a proper distribution of second-phase particles can provide the desired microstructure for improved properties and formability in wrought magnesium alloys.

Jan 1, 2004